The Makefile for binutils creates a broken symlink to "binutils-linaro" in
"trunk/build_dir/toolchain-<target>_gcc-4.9-linaro_uClibc-0.9.33.2".
Modify the Makefile to point the symlink to the correct directory.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 42954
Fix the move_config() procedure to properly find the corresponding disk if
the rootfs was mounted by PARTUUID instead of a device node.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42946
This kmod is required by the Alix APU 1D4 to be reachable after
installing an x86-64 image.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42945
* Rewrite ndp proxy using kernel proxying
* Aid flash-renumbering in hybrid DHCPv6-mode
* Unicast RAs to RS senders
* Add support for router address
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42944
We still don't have a smart sysupgrade method, but at least we can use
UBI which provides some protection for rootfs (SquashFS).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42941
UBI requires PEBs to be formatted (with a valid UBI header) or empty
(0xFF), however CFE doesn't clear blocks after flashing the image. To
workaround this problem, teach UBI to recognize EOF mark in a similar
way JFFS2 handles that in OpenWrt.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42940
This change configures grub to mount the rootfs by PARTUUID instead of the
device path if CONFIG_TARGET_ROOTFS_PARTNAME is unset.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42936
- Add current buildroot scm url as base feed to feeds.conf
- Prefer feeds.conf over feeds.conf.default when generating the SDK feeds.conf.default
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42935
- Consider not installed feeds as well
- Add option to decide whether to comment disabled feeds
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42931
Inside every LuCI package you need to clear luci-indexcache and
sometimes when installing non LuCI pacakges it's also needed to clear
it. Easier put it into default_postinst().
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 42923
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
SVN-Revision: 42922
The installation process on nand-based boards using ubi
like the BTHOMEHUBV2B makes use of a ramdisk image, so it
makes sense to generate this by default.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 42920
This patch adds missing architecture-specific headers for use with
eventfd(2). Fixes#16679.
Signed-off-by: Luis Dallos <ld@nkvd.ignorelist.com>
SVN-Revision: 42916
Currently JFFS2 end-of-filesystem marker 0xdeadc0de is included the
computation of image's MD5 checksum as part of the seama header. But
OpenWrt will erase blocks including and after the marker thus
invalidating the checksum after the first boot.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42915
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42914
Change the "help" info to emphasize that this option refers
specifically to packaging the toolchain that would be built anyway.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
SVN-Revision: 42912
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 42897
This change makes the profile of WDR4900 more consistent with other router
specific profiles.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
SVN-Revision: 42896
Error reported by buildbot:
Package kmod-at91-adc is missing dependencies for the following libraries:
input-core.ko
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 42893
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42892
pts/feeds update -a" can fail rather silently for feeds using git, as
the script does not pause when updating a feed fails. Instead it prints the
error message and calmly continues to the next feed. It is very easy to
overlook update errors with the feeds updated first, as their text scrolls
rapidly away from the screen.
This behaviour has not been a big problem with svn feeds, as svn update stops
with a conflict message and interactively forces the user to resolve or
postpone the conflict. In any case the svn error is noticed by the user.
Majority of the feeds use now git, so this silent failure can affect users
doing private builds in an increasing amount.
Below is an example of update failing and script continuing:
perus@v1404:/Openwrt/barrier$ ./scripts/feeds update -a
Updating feed 'packages' from
'https://github.com/openwrt/packages.git;for-14.07' ...
remote: Counting objects: 17, done.
remote: Compressing objects: 100% (15/15), done.
remote: Total 17 (delta 10), reused 8 (delta 1)
Unpacking objects: 100% (17/17), done.
From https://github.com/openwrt/packages
62031da..dc26009 for-14.07 -> origin/for-14.07
Updating 62031da..dc26009
error: Your local changes to the following files would be overwritten by merge:
utils/collectd/Makefile
Please, commit your changes or stash them before you can merge.
Aborting
failed.
Updating feed 'luci' from 'http://git.openwrt.org/project/luci.git;luci-0.12' ...
Already up-to-date.
Create index file './feeds/luci.index'
Updating feed 'routing' from
'https://github.com/openwrt-routing/packages.git;for-14.07' ...
...
The script prints "failed.", but does not break the updating process. The
"update_feed" function returns an error code 1, but that value is not checked
in the "update" function, which continues to the next feed.
Return 1 as error:
https://dev.openwrt.org/browser/trunk/scripts/feeds#L547
Call to update_feed without any error monitoring:
https://dev.openwrt.org/browser/trunk/scripts/feeds#L585
The included patch makes the feeds script to stop updating after failing to
update a feed.
The script continues to the refresh_config step despite a possible failure in
updating, so the stopping action just prevents the other feeds from updating
and makes the error more clearly visible.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 42891
Felix Fietkau
Steven Barth
Jo-Philipp Wich
Rafał Miłecki
John Crispin