UCI paramater multicast is added which allows to toggle multicast support on gre interfaces.
By default multicast support is enabled as gre tunnels are often used in combination with
routing protocols using multicast.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Nick Podolak <nicholas.podolak@dtechlabs.com>
SVN-Revision: 48596
* Enable drop_invalid by default to catch unnatted packets (#21738)
* Fix processing of inversions for -i, -o, -s, -d and -p flags
* Remove delegate_* chain indirection but rely on xt_id to identify own rules
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48551
Commit 6a7e56b adds support for adding local hostname for own lan ula adress
but if ula prefix is not specified results into an invalid config (address=/OpenWrt.lan/1)
causing dnsmasq not to start up.
Use lanaddr6 when adding local hostname as the lan ula address is constructed based on the
UCI parameters ip6hint and ip6ifaceid and thus not always ula prefix suffixed with 1
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 48495
RSA keys should be generated with sufficient length.
Using 1024 bits is considered unsafe.
In other packages the used key length is 2048 bits.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
SVN-Revision: 48494
Update to upstream Git HEAD to include VHT rate support and a number of
coverity scan fixes.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48487
This adds IPv6 support to qos-scripts for both tc/qdisc and the
iptables classification rules. The tc/qdisc part is accomplished
by removing "protocol ip" from the tc command line, causing the
rule to be applied to all protocols. The iptables part is
accomplished by adding each rule using both iptables and ip6tables.
This patch is based on previous work by Ilkka Ollakka and
Dominique Martinet.
Signed-off-by: Michael Marley <michael@michaelmarley.com>
SVN-Revision: 48452
This adds a "srciface" option that can be used on classification
rules in /etc/config/qos. This is useful to allow prioritization
based on the local network from which the traffic originates, for
example to deprioritize traffic from a guest network.
Signed-off-by: Michael Marley <michael@michaelmarley.com>
SVN-Revision: 48446
Set the save-mark mask for the qos_${cg} chain to 0xff instead of
0xf0. With the old value, the nibble that was saved would be
masked during the restore, preventing ingress traffic from being
classified. Thanks to nbd for recommending the fix.
Signed-off-by: Michael Marley <michael@michaelmarley.com>
SVN-Revision: 48388
The auth change appears to break the endpoint update for most users and with
my local tests the old update url works just fine.
This reverts commit 99c03a88cb6fed0519efdfaac305794653a12542.
SVN-Revision: 48384
Introduce config options client_cert2, priv_key2 and priv_key2_pwd
used for EAP-TLS phase2 authentication in WPA-EAP client mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 48345
WPA-EAP supports several phase2 (=inner) authentication methods when
using EAP-TTLS, EAP-PEAP or EAP-FAST (the latter is added as a first
step towards the UCI model supporting EAP-FAST by this commit)
The value of the auth config variable was previously expected to be
directly parseable as the content of the 'phase2' option of
wpa_supplicant.
This exposed wpa_supplicant's internals, leaving it to view-level to
set the value properly. Unfortunately, this is currently not the case,
as LuCI currently allows values like 'PAP', 'CHAP', 'MSCHAPV2'.
Users thus probably diverged and set auth to values like
'auth=MSCHAPV2' as a work-around.
This behaviour isn't explicitely documented anywhere and is not quite
intuitive...
The phase2-string is now generated according to $eap_type and $auth,
following the scheme also found in hostap's test-cases:
http://w1.fi/cgit/hostap/tree/tests/hwsim/test_ap_eap.py
The old behaviour is also still supported for the sake of not breaking
existing, working configurations.
Examples:
eap_type auth
'ttls' 'EAP-MSCHAPV2' -> phase2="autheap=MSCHAPV2"
'ttls' 'MSCHAPV2' -> phase2="auth=MSCHAPV2"
'peap' 'EAP-GTC' -> phase2="auth=GTC"
Deprecated syntax supported for compatibility:
'ttls' 'autheap=MSCHAPV2' -> phase2="autheap=MSCHAPV2"
I will suggest a patch to LuCI adding EAP-MSCHAPV2, EAP-GTC, ... to
the list of Authentication methods available.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 48309
This was generating a conffiles list that included the binary
and CONTROL/ files.
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
SVN-Revision: 48296
This adds support for configuring VTI interfaces within /etc/config/network.
VTI interfaces are used to create IPsec tunnel interfaces. These interfaces
may be used for routing and other purposes.
Example config:
config interface 'vti1'
option proto 'vti'
option mtu '1500'
option tunlink 'wan'
option peeraddr '192.168.5.16'
option zone 'VPN'
option ikey 2
option okey 2
config interface 'vti1_static'
option proto 'static'
option ifname '@vti1'
option ipaddr '192.168.7.2/24'
The options ikey and okey correspond to the fwmark value of a ipsec policy.
The may be null if you do not want fwmarks.
Also peeraddr may be 0.0.0 if you want all ESP packets go through the
interface.
Example strongswan config:
conn vti
left=%any
leftcert=peer2.test.der
leftid=@peer2.test
right=192.168.5.16
rightid=@peer3.test
leftsubnet=0.0.0.0/0
rightsubnet=0.0.0.0/0
mark=2
auto=route
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 48274
By default dnsmasq uses random ports for outbound dns queries;
when the minport UCI option is specified the ports used will
always be larger than the specified value.
This is usefull for systems behind firewalls.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 48244
This is a patch for CVE-2015-5252, CVE-2015-5296 and CVE-2015-5299. A
patchset for these vulnerabilities was published on 16th December 2015.
Signed-off-by: Jan Čermák <jan.cermak@nic.cz>
SVN-Revision: 48133
Source package gre was depending on kmod-ip6-gre, however the actual
kernel module package that is created is kmod-gre6. Therefore
update (source) package gre for ipv6 gre support.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 48100
In sta-only configuration, wpa_supplicant needs correct regulatory
domain because otherwise it may skip channel of its AP during scan.
Another alternative is to fix "iw reg set" in mac80211 netifd script.
Currently it fails if some phy has private regulatory domain which
matches configured one.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
SVN-Revision: 48099
iproute2-4.0 had connmark support added by nbd. This does not work
with 4.x kernels. iproute2-4.3 is the latest version and has his
changes mainlined. This patch updates the package to iproute2-4.3
and fixes the patches so that it compiles. This should resolve
ticket #21374.
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
SVN-Revision: 48098
Add back a slightly modified version of the lowlevel settings which
where removed with r46920.
In compare to the old lowlevel settings, the B43c tone is added to
tone_adsl_b and tone_adsl_bv.
If an unsupported tone value is used, the auto probing mode is used, in
compare to the fallback to tone_adsl_av and tone_vdsl_av with the old
lowlevel settings.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48054
According to ITU-T G.997.1 Amendment 2 (04/2013) section 2.1, bit 3 of
XTSE octet 8 either allow or denies the initialization of G.993.5.
Even if the current redistributable xDSL firmware doesn't include
G.993.5 vectoring support, enable this bit by default to allow people to
get their G.993.5 line working using a custom xDSL firmware.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48053
r47933 revealed that the driver/app in combination with the chosen
firmware does a good job in selecting a working xtse.
Use this probing mode if no annex is specified.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48052
This patch adds the missing VDSL2 bits to the annex specific XTSE (like
it should be according to the comments above the XTSE bits).
Since r47933 it's mandatory to remove the annex option to switch to
VDSL2 (only) operation mode.
As shown by ticket #21436 and a few mails I received personally, even
experienced users are not aware that they have to remove the annex
option to get their VDSL2 line working and as shown by this patch it
doesn't need to be that "complicated".
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48051
MD5SUM is wrong, it was not updated during last update to v1.4.1.
Thanks to Daniel Dickinson <openwrt@daniel.thecshore.com> for reporting it.
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 48017
Changed the tunnel update URL into format tunnelbrokers
example has, that made it work again. Current method gives "Username/Password
Authentication Failed." when I tried the wget line manually and logread
eventually says also "6in4: update failed". With corrected URL it works fine:
"good 111.222.333.444" or "nochg 111.222.333.444" and logread concurs with
success, and tunnel actually updates.
Tested-by: Vaasa Hacklab <info@vaasa.hacklab.fi>
Signed-off-by: Sami Olmari <sami@olmari.fi>
SVN-Revision: 48006
When using cli, print link state the same way kernel used to do it.
This will allow kernel switching PORT_LINK from SWITCH_TYPE_STRING.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47998
Only the conditional dependency ought to be required;
if build fails with JSON there is some other problem
at work.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47976
By default dnsmasq sends an ICMP echo request before allocating
an IP address to a host; the uci option noping allows to disable
this check.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 47974
Changed option nonwildcard from --bind-interfaces into --bind-dynamic.
With this, Dnsmasq binds the address of individual interfaces, allowing multiple
dnsmasq instances, but if new interfaces or addresses appear, it automatically
listens on those. This makes dynamically created interfaces work in the same way as
the default, but allows also use of other DNS-servers (like Named) at the same time
on diffirent interfaces where Dnsmasq is NOT configured, whereas with
--bind-interfaces will still reserve every interface even if not used and thus
disallowing use of any other DNS-program even on unused interfaces.
Tested-by: Vaasa Hacklab <info@vaasa.hacklab.fi>
Signed-off-by: Sami Olmari <sami@olmari.fi>
SVN-Revision: 47953
Using the JSON output option depends on json library so
add select json-c library when JSON output is selected.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47928
- 1.4.x has IPv6 support
- set C std explicitly due to gcc 5 changes/old code style of dante
- disable pam via configure vars since detection of without pam option
is broken (-lpam gets linked in if available)
- remove and refresh patches
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47926
- CONFIG_IFX_CLI is unused, couldn't find any reference to this config variable
- use disable-feature instead of enable-feature=no
- reorder configure args to have depending args together
- remove configure args which set the default value
- group enable-model and configure args which enable or disable features that
are covered by the feature set
The config.log contains the same values as before. The vdsl_cpe_control binary
has the same checksum as before.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47888
The typicial feature set doesn't include "DSL PM showtime counters support"
(INCLUDE_DSL_CPE_PM_SHOWTIME_COUNTERS). This feature provides the
vdsl_cpe_control command 'pmccsg', which is used by 'dsl_control status' to get
the line uptime.
The binary size increases to 103912 byte (+4256 byte) uncompressed.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47887
Add the option "--all-servers" which forces dnsmasq to send all
queries to all servers and then take the first answer.
Signed-off-by: Andréas Gustafsson <gurgalof@gmail.com>
SVN-Revision: 47857
this error was not visible until recent bump to
busybox 1.24.1 stable which introduced a warning message
when keyword 'local' is not used with a shell-function.
this does not change behavior and is a cosmetic cleanup.
fixes the following output:
root@box:~ ifup <interface>
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 1: not in a function
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 47828
This should ensure that lldpd is among the first processes to stop,
so that it has time to send the shutdown LLDPU to the other side,
before the network goes down.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47786
Support next to the non-HT/HT channel widths like HT20 or NOHT also VHT80
channels during the mesh join
iw dev mesh0 mesh join "meshnet" freq 5180 80MHz
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47782
Fix the id of NL80211_ATTR_WIPHY_ANTENNA_GAIN for antenna_gain command when
using compat-wireless 2015-10-26.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47778
Use the 'typical' compile configuration instead of 'full', which most
notably excludes the soap support.
/sbin/vdsl_cpe_control shrinks down to ~50%, from 178kb(!) to 90kb.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47769
In this upstream dsl driver app version the autoboot is deactivated activate
it again.
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47637
The scripts for authsae and iw use the option mesh_id to get set the
"meshid" during a mesh join. But the script for wpad-mesh ignores the
option mesh_id and instead uses the option ssid. Unify the mesh
configuration and let the wpa_supplicant script also use the mesh_id from
the configuration.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47615
The OpenWrt wireless configuration for mcast_rate is defined as Kbit/s when
using wpa_supplicant for IBSS/802.11s and iw for unencrypted IBSS/802.11s.
But when using authsae, the unit for the same option is redefined as
Mbit/s. Better use the same unit for this option independent of the backend
which is used.
Old values for mcast_rate (< 1000) are still interpreted Mbit/s to avoid
problems during upgrades from older versions.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47614
The variable $mesh_id was never defined in authsae_start_interface and thus
the option meshid in $authsae_conf_file was always set to "".
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47613
Felix Fietkau
Jo-Philipp Wich
Rafał Miłecki
John Crispin
Nicolas Thill
Hauke Mehrtens
Jonas Gorski