We did not start the PHY when an external phy was in use. Without this
patch the driver uses half duplex mode and the switch uses full duplex
mode, which causes problems.
Thank you fback for spotting this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39719
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.
Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39703
That will be used to drive the 74HC595 serial-in/parallel-out
8-bits shift register which can be found on some RouterBOARDs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39702
The serial flash devices used on the ROuterBOARDs are
supporting 4KiB erase blocks. Enable the small sector
erase option in the m25p80 driver to avoid superfluous
erase/write of adjacent blocks.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39696
This is a backported patch for the gianfar ethernet driver
used in TPLink 4900 v1. It is supposed to fix the error which
show up in dmesg with:
NETDEV WATCHDOG: eth0 (fsl-gianfar): transmit queue xy timed out
Full upstream patch is at: http://patchwork.ozlabs.org/patch/271242
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
SVN-Revision: 39692
Only netboot tested, so no images or now.
GbE ports are only working in FE mode, and leds do not work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39679
Completely untested except for booting from network; wan port
only works in 10/HD, lan1 only in 100/FD.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39678
BCM63168 has 6 ports (3 FE PHY, 1 GE PHY, two RGMII) and BCM63268
has two additional RGMII ports, making it 8.
Fix this by checking the chip variant and applying an appropriate
limit.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39677
Support for Asmax AR 1004g router
Signed-off-by: Adrian Feliks <mexit@o2.pl>
Patchwork: http://patchwork.openwrt.org/patch/4464/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39674
This adds profile and build image for Sagemcom F@st2704, using b43
driver.
For WiFi to work properly BCMA fallback SPROM support patch must
be applied (http://git.io/z1Ki8A).
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4212/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39673
This adds userspace support for Sagemcom F@st 2704 router.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4215/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39672
This adds kernel support support for Sagemcom F@st 2704 wireless ADSL
router.
It's a BCM6328-based 802.11n wireless router with USB port and ADSL2+
modem equipped with 64 MiB RAM and 8 MiB flash.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4266/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39671
Update the Ventana device-tree to match upstream:
- Add IMX6Q/IMX6DL variants for GW54xx/GW53xx/GW52xx/GW51xx
- align pinctrl with upstream
- consolidate multiple patches into one
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39644
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result. I have cleaned up this patch.
When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.
This patch applies cleanly to SVN 39392.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
- drop the 'rb951ui_wlan_init' function and rework the code to
use the recently introduced rb95x_wlan_init function instead,
- fix GPIO number of the port5 LED,
- rename LEDs according to the standard LED naming conventions,
and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39641
This is a backport of code to improve the quality of fq_codel
hashing for 3.10 for some encapsulated protocols.
Not needed in 3.11 and later.
Patch-by: Dave Taht <dave.taht@bufferbloat.net>
Patchwork: http://patchwork.openwrt.org/patch/4902/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39640
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4849/
[juhosg:
- use the Archer C7 specific LED setup instead of adding
identical code]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39636
This missing bit of the hack saves hugely on instruction traps
on tcp connections to ar71xx based routers.
Patch-by: Dave Taht <dave.taht@bufferbloat.net>
Patchwork: http://patchwork.openwrt.org/patch/4905/
[juhosg: adjust subject, refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39626
Solves ticket #14356 <https://dev.openwrt.org/ticket/14356>
Without this patch, UART output will show only 4 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000050000 : "u-boot"
[ 0.760000] 0x000000050000-0x000000070000 : "u-boot-env"
[ 0.770000] 0x000000070000-0x0000007f0000 : "firmware"
[ 0.790000] 0x0000007f0000-0x000000800000 : "art"
and then linux complains :VFS: Cannot open root device "(null)"
With this patch, UART out will show 7 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.760000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.770000] 0x000000050000-0x0000007f0000 : "firmware"
[ 0.780000] 2 netgear-fw partitions found on MTD device firmware
[ 0.780000] 0x000000050000-0x00000014b440 : "kernel"
[ 0.790000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.800000] 0x00000014b440-0x0000007f0000 : "rootfs"
[ 0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.820000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.830000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.830000] 0x000000340000-0x0000007f0000 : "rootfs_data"
[ 0.840000] 0x0000007f0000-0x000000800000 : "art"
This patch is tested against r39502 of trunk.
Signed-off-by: Jonathan Chang <changcs@santos.ee.ntu.edu.tw>
Patchwork: http://patchwork.openwrt.org/patch/4870/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39625
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0xfe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-dockstar-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-by: Alexander Couzens <lynxis@fe80.eu>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39593
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0xfe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-ib62x0-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-by: Luka Perkov <luka@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39592
Previous patch was pushed due to false user report. While at it fix alphabetic
ordering.
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0x1fe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-iconnect-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39591
Some ARV4510PW units seem to have unstable PCI due to missing pull-up
resistors. This patch makes sure that the GPIO lines are driven properly.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 39587
The mtdpartsize macro triggers shell errors on various Linux distributions
when the partname argument $(1) does not appear within the partmap $(2).
Change the sed pattern to only emit anything if a successful substitution
occured and only evaluate the arithmetic expression if something was printed
by the sed program.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39583
This Armada XP GP board from Marvell comes with:
* 2GB DDR3 DIMM
* 1GB NAND flash (8-bit interface)
* 16MB NOR flash (16-bot interrface)
* 16MB SPI flash
* SDIO module
* 3 PCIe
* 1 SATA link
* 2 USB EHCI
* 1 internal SSD
* 4 Ethernet Gigabit
* 1 RS232 port over USB
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
SVN-Revision: 39568
The config-3.10 doesn't specify the configuration of the backported PCI
features, and the Marvell EBU Device Bus Controller, this will prevent
a clean compile. This patch enables these features to archive a clean compile
without having to specify the state of these configuration after starting to
compile.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
SVN-Revision: 39567
This is a backport of the patches accepted to the Linux mainline related to
mvebu SoC (Armada XP and Armada 370) between Linux v3.12, and Linux v3.13.
This work mainly covers:
* Finishes work for sharing the pxa nand driver(drivers/mtd/nand/pxa3xx_nand.c)
between the PXA family, and the Armada family.
* timer initialization update, and access function for the Armada family.
* Generic IRQ handling backporting.
* Some bug fixes.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
CC: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39566
This is a backport of the patches accepted to the Linux mainline related to
mvebu SoC (Armada XP and Armada 370) between Linux v3.11, and Linux v3.12.
This work mainly covers:
* Ground work for sharing the pxa nand driver(drivers/mtd/nand/pxa3xx_nand.c)
between the PXA family,and the Armada family.
* Further updates to the mvebu MBus.
* Work and ground work for enabling MSI on the Armada family.
* some phy / mdio bus initialization related work.
* Device tree binding documentation update.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
CC: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39565
This is a backport of the patches accepted to the Linux mainline related to
mvebu SoC (Armada XP and Armada 370) between Linux v3.10, and Linux v3.11.
This work mainly covers:
* Enabling USB storage, and PCI to mvebu_defconfig.
* Add support for NOR flash.
* Some PCI device tree related updates, and bus parsing.
* Adding Armada XP & 370 PCI driver, and update some clock gating
specifics.
* Introduce Marvell EBU Device Bus driver.
* Enaling USB in the armada*.dts.
* Enabling, and updating the mvebu-mbus.
* Some SATA and Ethernet related fixes.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
CC: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39564
smsc95xx.ko depends on crc16.ko on kernel >= 3.8
There was an additional kmod-usb-net-smsc95xx definition in the mxs
target code which conflicted with the one in the common area.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39562
This adds empty definitions for the PCI quirks functions when they
should not be included in the kernel.
This is based on a patch by Daniel <daniel@makrotopia.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39534
The int brnf_call_ebtables in the header should be extern, otherwise
every object file gets its own int and they will conflict when linking
the binary.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39533
These should either be disabled or not present in the config, else
they might cause build issues because of unexpected unpackaged
modules, as it is the case for LEDS_CLASS.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39529
The 3.10.x infrastructure has been present for some time, and seems to
run fine here.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 39483
It was recently sent to linux-mips for comments. It adds workaround for
WNR3500L to enable USB port.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 39469
This does not add any new features, just some changes to the patches
and a first try to use dt to set the irqs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39466
The original dragino2 board support was missing some changes from the
upstream svn repository (http://svn.dragino.com/dragino2) that supported
sysupgrade.
[juhosg: change subject]
Signed-off-by: Karl Palsson <karlp@remake.is>
Patchwork: http://patchwork.openwrt.org/patch/4801/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39429
Since the yaffs code update (r39084), it is not
possible to install OpenWrt on RouterBoards with
small-page NAND chips. Fix the yaffs code to make
it work again.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39409
The 3.6 kernel isn't used by any of the x86 subtargets, so remove it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39403
Use the 'swconfig_trig_set_brightness' function to set
the brightness value of the LED when the link goes down.
This ensures that the last brighness value is saved into
a local variable which is used to track the actual LED
status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39402
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39392
Get the size of the mtd partitions directly from the
MTD layout and remove the superfluous macro parameters.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39384
The macro checks the size of the rootfs image even if
the second parameter of the macro contains the size of
an eraseblock. It is wrong because the size of the
kernel image will be adjusted to the next eraseblock
and the resulting image might be too large.
Fix the macro to check the size of the final image
instead of the rootfs image.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39383
This reverts r38197.
The automatically created firmware partition includes
the partition_table partition. Apart from the partition
table, this partition contains sensitive data on some
Compex devices which data can be destroyed when the
firmware partition gets modified. Revert the change to
prevent that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39382
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39373