Instead of setting them up on invocation of brcm63xx_detect, set them
when calling diag.sh based.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44837
Board IDs are not unique, so in preparation for depricating them, always
use board_name for any (default) configuration decisions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44836
Use the device tree model property for detecting the board instead
of board id from nvram if present.
Since we can now directly detect the DVA-G3810BN, we can remove the
extra check for it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44834
Take full board name from devicetree, if present. Provide a method
for retrieving the board name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44833
Rename board_name to board_id to prepare for using board_name as a
proper name for the board.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44832
This adds support for the Netgear DGND3700 v1 and DGND3800B.
DGND3700 v1 and DGND3800B are exactly the same router, only one difference,
the factory firmware. This patch produces two factory firmwares for each router.
The router includes an onboard NAND flash for extra storage. NAND is currently
not supported in bcm63xx, so no code added for this part. The NOR flash (32MB)
is enough for storing an openwrt firmware.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: Add back commit message from v1]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44831
Split out kmods from ALL to make it easier to create local builds that
are compatible kmod-wise with releases.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44830
Build all geode platform drivers into the kernel
Remove kmod-* packages for these drivers
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44809
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44795
This patch allows AP148 to boot from NOR flash.
As we're using a FIT image as kernel (which includes kernel bin + DTB)
we enable the MTD_SPLIT_FIT_FW kernel option, which will detect the FIT
image and automatically split the "firmware" partition into 2 MTD parts
(kernel + rootfs).
The rootfs will then be parsed and split between rootfs + rootfs_data,
as usual.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44794
Only one bootargs is really needed: the tty port. All the other
information will use the OpenWrt mechanisms.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44793
If this option is enabled, the FIT image format will be detected and
split by the mtdsplit code. Detection is based upon the FDT magic, which
will trigger the parsing and detection of the rootfs, ending-up in the
creation of the 2 new partitions.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44792
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.
The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44791
Certain DHCP servers push a gateway outside of the assigned interface subnet,
to support those situations install a host route towards the gateway.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44789
It will now actually enable the mib counters instead of enabling rx/tx for
the first switch port.
Reported-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44788
Jonas Gorski
John Crispin
Felix Fietkau
Rafał Miłecki
Jo-Philipp Wich