This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.
This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).
This is especially useful if an OpenWrt device with two radios is used to
retransmit the same network (one in AP mode for other clients, one as STA for
the uplink); the following configuration prevents the device from associating
with itself, given that the own AP to be avoided is using the bssid
'C0:FF:EE:D0:0D:42':
config wifi-iface
option device 'radio2'
option network 'uplink'
option mode 'sta'
option ssid 'MyNetwork'
option encryption 'none'
list bssid_blacklist 'C0:FF:EE:D0:0D:42/00:FF:FF:FF:FF:FF'
This change consists of the following cherry-picked upstream commits:
b3d6a0a8259002448a29f14855d58fe0a624ab76
b83e455451a875ba233b3b8ac29aff8b62f064f2
79cd993a623e101952b81fa6a29c674cd858504f
(squashed to implement bssid_{white,black}lists)
0047306bc9ab7d46e8cc22ff9a3e876c47626473
(Add os_snprintf_error() helper)
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 44438
Introduce configuration options to build an "hardened" OpenWRT.
Options to enable Stack-Smashing Protection, FORTIFY_SOURCE and RELRO
have been introduced.
uClibc makefile now automatically detects if SSP support is necessary.
hostapd makefile has been fixed to use "^" as sed separator since
using a comma was problematic when using "-Wl,-z,now" and the like in
TARGET_CFLAGS.
Currently enabling SSP on user space depends on enabling SSP kernel
side, this is due to the fact that TARGET_CFLAGS are used to build
kernel modules (at least). Suggestions on how to avoid this are welcome.
Using "select" instead of "depends on" doesn't seem to work with choice
entries.
Tested with a lantiq (WBMR) router, GCC 4.8, uClibc and a subset of
the available packages.
Needs to be tested with GCC 4.9 and the remaining packages.
PIE not currently included.
Signed-off-by: Alessandro Di Federico <ale+owrt@clearmind.me>
SVN-Revision: 44005
This patch fixes adding new stations for some specific drivers when
using more than 1 BSS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43951
The uapsd option sets the uapsd_advertisement_enabled flag in hostapd.
The check for phy support is already implemented here in hostapd since 2011:
http://w1.fi/cgit/hostap/commit/?id=70619a5d8a3d32faa43d66bcb1b670cacf0c243e
So this can be safely set to 1 as default.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43846
In r41872 and r42787 Dynamic VLAN support was reintroduced, but the vlan_bridge
parameter is not read while setting up the config, so the default is used which
is undesirable for some uses.
Signed-off-by: Ben Franske <ben.mm@franske.com>
SVN-Revision: 43473
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
The wpa_psk_file option offers the possibility to use a different WPA-PSK key for each client. The directive points to a file with the following syntax:
mac_address wpa_passphrase_or_hex_key
Example:
00:11:22:33:44:55 passphrase_for_client_1
00:11:22:33:44:67 passphrase_for_client_2
00:11:22:33:44:89 0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
So it is possible to specify both ASCII passphrases and raw 64-chars hex keys.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43001
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
In r41872 Dynamic VLAN support was reintroduced, but the vlan_naming
parameter is not read while setting up the config, so it always
defaults to 1.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 42787
With this patch WPS discovery can be started or canceled over ubus if
WPS is enabled in wireless configuration. This is equivalent of
'hostapd_cli wps_pbc' and 'hostapd_cli wps_cancel' commands.
Signed-off-by: Petar Koretic <petar.koretic@sartura.hr>
SVN-Revision: 42459
This patch brings full dynamic vlan support to netifd that existed in hostapd.sh in Attitude Adjustment.
Signed-off-by: Joseph CG Walker <Joe@ChubbyPenguin.net>
[jow@openwrt.org: changed commit message, rebased on top of current hostapd.sh]
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41872
Fixed wpa_supplicant when the radio is in 40MHz mode so that it no
longer restarts hostapd with the second channel disabled.
Signed-off-by: Lance Chaney <furryfur1@gmail.com>
SVN-Revision: 41019
rsn_preauth is used outside of "case $auth_type", so if it is set
for an EAP-enabled SSID, it would also be set for the following
non-EAP-enabled SSIDs, because it would not be read again.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 41012
`own_ip_addr` is used by hostapd as NAS-IP-Address.
This is used to identify the AP that is requesting the authentication of the
user and could be used to define which AP's can authenticate users.
Some vendors implement only NAS-Identifier or NAS-IP-Address and not both.
This patch adds ownip as an optional parameter in /etc/config/wireless.
Signed-off-by: Thomas Wouters <thomaswouters@gmail.com>
SVN-Revision: 40934
This patch fixes compilation failure for hostapd when using eglibc 2.15.
Signed-off-by: Zachery Stoddard <zacherystoddard@gmail.com>
SVN-Revision: 40575
This patch implements support for 802.11s protected mesh wireless networks (using authsae) in the netifd framework.
Until meshd-nl80211 implements a proper -P option for the PID file, this uses shell backgrounding in order to be able to get the PID for the process.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 40497
r39995 introduced a new parameter wps_pbc_in_m1 to wifi wps config, but
apparently did not provide a default value 0.
When that option's non-existing value is later evaluated in
/lib/netifd/hostapd.sh, it causes the "bad number" error to be logged in
syslog if user has not set the wps_pbc_in_m1 option. The error materialises
only if user has enabled wps.
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio1 (1254): sh: bad number
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio0 (1253): sh: bad number
Discussion in bug 15508: https://dev.openwrt.org/ticket/15508#comment:3
Error is caused by line 282:
https://dev.openwrt.org/browser/trunk/package/network/services/hostapd/files/netifd.sh#L282
My patch sets the parameter's default value to 0, which does nothing. The
default might also be set a bit later in the function, but this felt like the
most clear place to do that.
Signed-off-by hnyman <hannu.nyman@iki.fi>
SVN-Revision: 40469
Option pbc_in_m1 is being used as a WPS capability discovery
workaround for PBC with Windows 7.
Add possibility to enable this workaround from UCI.
To enable it, turn on wps and set wps_pbc_in_m1 parameter to 1.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
SVN-Revision: 39995
This patch introduces 802.11ac support to mac80211 and hostapd. The split of
VHT160 in two 80 MHz bands is not yet supported, since it requires an
additional user supplied parameter for the channel of the second band.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
[sven@open-mesh.com: Rebased patch, merged htmode and vhtmode,
removed special hwmode, replaced uci vht_capab list with overwritable
autoconfig, fixed hostapd integration, fixed commit description, add HT40+/-
for VHT modes, add VHT40 center_freq autoconfig, refactored major parts]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 39456
John Crispin
Felix Fietkau
Rafał Miłecki
Nicolas Thill
Steven Barth
Luka Perkov
Jo-Philipp Wich