Commit Graph

21 Commits (8eb0b7ab3dd22d800afd65fc63efa52bfb6f99fa)

Author SHA1 Message Date
Florian Fainelli 16dfe8b4d1 add support for BT Voyager 2110 (#8810)
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>

SVN-Revision: 26959
2011-05-20 10:06:25 +00:00
Florian Fainelli 6c8387fe15 add support for DSL-2640B rev B2
Signed-off-by: Adrian Feliks <mexit@o2.pl>

SVN-Revision: 26958
2011-05-20 10:06:22 +00:00
Florian Fainelli 3e83f60a66 add support for D-Link DVA-G3810BN/TL
This patch adds support for D-Link's DVA-G3810BN/TL product.

Signed-off-by: Roman Dumycz <roman@secureas.com>

SVN-Revision: 26956
2011-05-20 10:06:15 +00:00
Florian Fainelli f0a99c1692 add support for BT Voyager 2500 (#9070)
SVN-Revision: 26954
2011-05-20 10:06:07 +00:00
Florian Fainelli 9c8a2d5961 bcm63xx: Add support for the T-Home Speedport W 303V
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 26878
2011-05-11 13:34:14 +00:00
Florian Fainelli 7d3b735854 bcm63xx: Update support for the DSL-274xB revision C
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.

While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 26876
2011-05-11 13:33:50 +00:00
Florian Fainelli 0fb1c2d537 bcm63xx: Accept any led with power in its name as power led
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 26875
2011-05-11 13:33:45 +00:00
Florian Fainelli b7f8e1276d add support for 'MAGIC' bcm6348-based board
I wrote a patch to add 96348SV board (aka MAGIC) support to trunk.
In my case I've found it in a Telsey "Alice W-Gate" router, fairly common
(in the past) in Italy.

I used the board definition (GPIOs, leds, ...) from the Broadcom GPL-2
relased code (here is a mirror: http://beghiero.myftp.org/sorgenti/boardparms.c )

Thanks to KanjiMonster for the support on the IRC channel.

Signed-off-by: Laurento Frittella <laurento.frittella@gmail.com>

SVN-Revision: 25584
2011-02-19 12:44:27 +00:00
Florian Fainelli 2d3ed6dc2d fix T-Com Speedport W 500V default config
The device is called SPW500V, not SP500W.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 25431
2011-02-09 13:09:02 +00:00
Daniel Dickinson 6ee5411686 base-files: Added uci-defaults script to run mtd fixtrx on firstboot for devices that need it.
Signed-off-by: Daniel Dickinson <daniel@cshore.neomailbox.net>

SVN-Revision: 24836
2010-12-26 04:18:04 +00:00
Daniel Dickinson 44e22cbd49 Fixed Comtrend CT536_CT5621 board settings. These boards are based on the 96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network.
SVN-Revision: 24442
2010-12-10 18:59:58 +00:00
Daniel Dickinson 7129521696 base-files: Added network defconfig because board only has one ethernet (4-port switch)
SVN-Revision: 24273
2010-12-06 02:01:08 +00:00
Daniel Dickinson 314bce63e6 bcm63xx: Add support for the T-Com Speedport W 500V.
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 24190
2010-11-28 22:04:44 +00:00
Daniel Dickinson c51d772e62 bcm63xx: Finalize support for DSL-274xB, rev C2.
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 24188
2010-11-28 22:04:36 +00:00
Daniel Dickinson 8fa9b24a4c bcm63xx: Allow 'colored' power leds.
Since some devices have more than one power led, they might be separated by
their color in the name. To also allow them to be on after leaving preinit,
set any status led starting with 'power' to on instead of only those with
the exact name of 'power'.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 24187
2010-11-28 22:04:30 +00:00
Daniel Dickinson b1b318750a bcm63xx: Add defconfigs.
Port the mechanism for different default configurations from ar71xx and
use the old configuration as the default configuration. This should have
no functional differences to before.
While we are at it, remove the obsolete nat option.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 24185
2010-11-28 22:04:19 +00:00
Daniel Dickinson a5fdf57a1b base-files: diag.sh: For power button as preinit status led, end with led left on, not off
SVN-Revision: 22466
2010-08-02 19:33:08 +00:00
Daniel Dickinson cc8fba8441 brcm63xx: Added LED code for preinit (/etc/diag.sh) for 96348GW (Tecom 6x00)
SVN-Revision: 21627
2010-05-30 01:32:58 +00:00
Florian Fainelli a0a85ba7c6 we are using the default-on trigger for power LEDs, no need to change their state from userspace
SVN-Revision: 16892
2009-07-18 09:27:33 +00:00
Florian Fainelli ecad504c39 register GPIO-connected LEDs for known boards
SVN-Revision: 16887
2009-07-18 00:40:23 +00:00
Florian Fainelli 4fc7535fc7 Make 4-port LAN and 1 port wan configurations work
SVN-Revision: 13362
2008-11-26 15:51:55 +00:00