When running wifi detect, the user will be told on error output that
wifi detect is deprecated, that wifi config must be used instead. Also
the commit that changes it is referenced for further info.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
Since commit 5f8f8a3661 wifi detect does
not longer work and wifi config it's used to configure not yet
configured wireless devices.
This commit changes command usage to reflect that change.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
The firmware hotplug script tries to read the mac address from a
partition with the name "uboot-env" which does not exist (instead it's
name is uboot_env). This broke calculation of the new checksum (after
patching the mac address) which resulted in ath9k refusing to use the
EEPROM data.
The original error reported by ath9k was:
PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
ath: phy0: Bad EEPROM checksum 0x2523
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:0e.0: Failed to initialize device
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
f107656 netifd: Add option to configure locktime for each device
cdc0e80 interface: add prefix assignment priority support
6397f5e device: add veth support
6228d0f wireless: fix _wireless_add_process
7cc2f10 treewide: fix white space errors
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
platform_find_rootfspart() fails if the kernel partition comes before the
rootfs partition. The proposed patch fixes this while preserving what I
understand was the original idea: stop at first match.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
When running "make kernel_menuconfig" in a clean tree, it fails with:
make[1]: *** No rule to make target 'tools/quilt/install'. Stop.
Replacing the dependency with 'tools/quilt/compile' fixes the issue (quilt
and all its prerequisites will be built, and quilt will be installed in
staging_dir).
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Effects of the bugs could include memory corruption, tx hangs, kernel
crahes, possibly other things as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Upstream linux commit 7523e4dc5057e "module: use a structure to
encapsulate layout." moves some of the struct module members into a
separate struct module_layout.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Do not put the probe function into the __init section, but use the normal
section. This fixes a section mismatch warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were dropped because they are already applied
upstream:
0012-pinctrl-lantiq-fix-up-pinmux.patch
0013-MTD-lantiq-xway-fix-invalid-operator.patch
0014-MTD-lantiq-xway-the-latched-command-should-be-persis.patch
0015-MTD-lantiq-xway-remove-endless-loop.patch
0016-MTD-lantiq-xway-add-missing-write_buf-and-read_buf-t.patch
0017-MTD-xway-fix-nand-locking.patch
0044-pinctrl-lantiq-introduce-new-dedicated-devicetree-bi.patch
0045-pinctrl-lantiq-Fix-GPIO-Setup-of-GPIO-Port3.patch
0046-pinctrl-lantiq-2-pins-have-the-wrong-mux-list.patch
0047-irq-fixes.patch
0047-mtd-plat-nand-pass-of-node.patch
0060-usb-dwc2-Add-support-for-Lantiq-ARX-and-XRX-SoCs.patch
0120-MIPS-lantiq-add-support-for-device-tree-file-from-bo.patch
0121-MIPS-lantiq-make-it-possible-to-build-in-no-device-t.patch
122-MIPS-store-the-appended-dtb-address-in-a-variable.patch
The PHY driver was reduced to the code adding the LED configuration,
the rest is already upstream:
0023-NET-PHY-adds-driver-for-lantiq-PHY11G.patch
The SPI driver was replaced with the version pending for upstream
inclusion:
New driver:
0090-spi-add-transfer_status-callback.patch
0091-spi-lantiq-ssc-add-support-for-Lantiq-SSC-SPI-controller.patch
Old driver:
0100-spi-add-support-for-Lantiq-SPI-controller.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch add ZyXEL NSA325 2-Bay Media Server
The ZyXEL NSA325 device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1600Mhz
- SDRAM memory: 512MB DDR2 400Mhz
- Gigabit ethernet: Marvell Alaska
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II ports (internal)
- 2 USB 2.0 ports (back)
- 1 USB 3.0 port (front)
- Fan (fixed speed)
- hardware watchdog in a mcu
Basically a bigger, more powerful version of NSA310,
installation is the same as they share the same flash layout.
A notable difference is that there is a hardware watchdog
in a mcu on the board, which is disabled by default in the LEDE u-boot.
The watchdog is also disabled with a GPIO activation through
raw register change when kwbooting or it would reset the board before
the new uboot was transferred.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
switch nsa310b mac address reading to mtd_get_mac_ascii helper as
it seems the fw_env.config file is created way later than when
network is set up, when I tested I still had that file included
in the image through /files folder.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
When we merged all the Geode boards into one generic target, the default
network and LED configuration was lost. Put it back.
Fixes: 9e0759ea26 ("x86: merge all geode based subtargets into one")
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Important change was made in 1.0.18: all sub-libs were merged
in one and only libc similarly to musl.
See [1] for more details.
To support that we had to remove refences to those sub-libs like
libpthread, libcrypt, libdl, libm, libutil etc.
[1] http://cgit.uclibc-ng.org/cgi/cgit/uclibc-ng.git/commit/?id=29ff9055c80efe77a7130767a9fcb3ab8c67e8ce
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Currently on attempt to configure uClibc with "V=s" user is prompted
to answer on configuration questions. Major inconvenience here is
build procedure get paused until user answers all questions.
That happens because not all symbols are defined in our .config.
Solution is as simple as usage of "olddefconfig" target instead of
simple "oldconfig". In that case default values get silently set
for symbols not defined by our .config explicitly.
We haven't noticed that subtle issue before because without "V=s"
what we do is "make oldconfig < /dev/null" which automatically
answers all questions :)
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
-mXXX option is deprecated already in arc-2016.03 toolchain
and removed completely starting from arc-2016.09.
Direct replacement is -mcpu=XXX which is already supported by
arc-2016.03 used today in Lede.
With that change we'll be ready for ARC toolchain update still
keeping everything working with current tools.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
The only HMACs currently available use MD5 and SHA1, both of which have known
weaknesses. We already compile in the SHA256 code since we use Curve25519
by default, so there's no significant size penalty to enabling this.
Signed-off-by: Joseph C. Sible <josephcsible@users.noreply.github.com>
David Pinilla Caparrós
Giuseppe Lippolis
Yangbo Lu
Chuanhong Guo
Martin Blumenstingl
Hans Dedecker
Felix Fietkau
Koen Vandeputte
Thibaut VARENE
Baptiste Jonglez
Hauke Mehrtens
Alberto Bursi
Christian Lamparter
David Woodhouse
Alexey Brodkin
Tim Harvey
John Crispin
Joseph C. Sible