This prevents generating every supported image, except for de "Default" profile.
Also fixes Neufbox 6 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42210
Use generic profiles for brcm63xx instead of having similar profiles for
each subtarget.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42208
This changes board info to match the Wiki
http://wiki.openwrt.org/toh/huawei/hg556a, removes the no longer needed
fallback board and fixes HG556 Ralink eeprom extraction.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: rename partitions instead]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42206
There is a group of devices that lzma-loader doesn't work with. They
simply hang at "Starting program at 0x80001000" which is really hard to
debug and we didn't find any solution for this for years.
Broadcom doesn't use lzma-loader on these devices anyway. They decided
to drop lzma-loader and use less optimal LZMA compression that can be
handled by CFE itself (it doesn't use dictionary).
So support these devices we will need kernel compressed with different
parameters and trx without a loader.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42205
Switch in Edimax 3G-6200n also require full switch reset, not only vlan definitions. Tested on Edimax 3G-6200n.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42194
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42193
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42184
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42180
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 42179
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.
Tested on hardware.
[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 42178
The conversion was not 100% correct and leads to u-boot failing to
verify the CRC, revert that change for now.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42170
This patch is causing more harm than good on most AR7 routers out there,
better have no manageable switch rather than no ethernet connection, at
least for now.
Fixes#16523, #5927
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42168
The GW5520 is a small form-factor single-board computer with the following
features:
* 70x100mm form-factor
* IMX6DL 800MHz SoC (IMX6Q optional)
* 512MB 32bit DDR3 SDRAM (up to 2GB optional)
* 256MB NAND FLASH (up to 2GB optional)
* Gateworks System Controller
* 2x front-panel Intel i210 GbE adapters with passive PoE support
* 2x MiniPCIe sockets with USB support
* 2x front-panel USB
* 1x rear-panel full-size HDMI connector
* 1x front-panel bi-color user LED
* 1x front-panel user pushbutton
* 1x rear-panel barrel jack for power
* 1x Application connector with:
* 2x TTL level UARTs
* 10x TTL level Digital IO
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42148
The GW16083 Ethernet Expansion Mezzanine adds the following to supported
Gateworks baseboards:
* 7-port Ethernet Switch
* 4x RJ45 ports (ENET1-4) supporing 802.11af/at PoE (with optional PoE module)
* 2x RJ45 ports or SFP module (ENET5-6) (auto-selected)
This series adds support for a phy driver that adds support for ENET5/ENET6
PHY adding initialization for those PHY's and a polling mechanism that detects
SFP insertion and configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42147
The GW16082 miniPCI Expansion Mezzanine has the INTA/B/C/D IRQ's reversed
from the PCI standard. This will soon be resolved in the bootloader via
devicetree, but in the meantime this will work around the issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42146
Now that we migrated all users to dtb based detection, we can drop the
board fixup code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42129
This requires individual images for each board version for now.
Linux partition was shrunk to ensure writing thewrong image won't
erase wifi calibration data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42126
Add the required nodes to the dtsi files and code to prevent double
registration from the board support code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42123
In preparation for switching to dtb based board identification, add
support for building lzma-loader and lzma cfe kernels with dtb
appended.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42121
Allow appending a dtb blob to the binary and use it for identifying the
board. Fall back to nvram based identification in case of no dtb passed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42119
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42088
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42083
In r41578 this was added in order to make default images bootable for the BB
release. We need more generic approach for this.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42071
Apparently this is a fairly common refurb unit of the 3800 series now,
with merely the recognition string changed in the boot loader.
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 42023
Created on basis of 3.10 config. Remove few obsolete symbols and add new
upstream symbols. New symbols left in its default state.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41996
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
SVN-Revision: 41993
Fix IFF_NO_IP_ALIGN location which is collide with new netdev private flag
IFF_MACVLAN.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41992
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.
Signed-off-by: Lintel <lintel.huang@gmail.com>
SVN-Revision: 41961
This commit implements a new netfilter match "xt_id" which can be used to
attach unsigned 32bit IDs to iptables rules.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41945
Mostly works except for USB led. Flashing not tested yet. Mostly
as an example for the sprom fixup code.
Fixup values taken from GPL tarball by comparing bcm43217_map.c
with the struct in sprom.c.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41944
Rework fallback sprom support by providing different sproms for
different chips. Also make it optional to use.
This likely causes sprom fallback support to break on a few boards.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41942
Now that BB is branched off, we can now switch to 3.14 and start
breaking stuff again.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41941
Add a working lzma loader and use it for generating initramfs kernels
to allow easily netbooting elf kernels on devices with a 4 MiB CFE
size limit.
Based on ar71xx's lzma-loader.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41940
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41939
This patch adds support for setting SPI_CS1 as Chip Select, Watchdog reset output and GPIO#27.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41938
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41932
without this the build for NBG6716 fails due to missing packages
https://dev.openwrt.org/ticket/17325
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41930
This is a backport of bcma from wireless-tesing/master tag master-2014-07-29-1.
For kernel < 3.10 this only adds the header changes needed by more
recent b43 versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41899
Fix a typo: gpio 21 is already used for the WPS led. Gpio 20 is the
right one (tested) for the mode switch. Confirmed that
/sys/kernel/debug/gpio state followed the position of the switch.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41858
Jonas Gorski
John Crispin
Hauke Mehrtens
Florian Fainelli
Luka Perkov
Imre Kaloz
Jo-Philipp Wich
Felix Fietkau
Steven Barth
Zoltan Herpai
