The GPIO for reset switch is wrong in definition. Further the key codes for the two additional buttons are ineffective.
Both is fixed here.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.
To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:
VR9 # run reset_uboot_config
VR9 # reset
VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The mac address is printed on the label at the bottom of the case.
The following steps are need to be done during first install:
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.
Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.
A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The WBMR boards are the only ones in the whole tree selecting the wpad
and hostapd-utils package by default.
Remove the wps uci-default script as well, there is no obvious reason
why the wps config need to be set only for this board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In case the adsl/vdsl service is disabled intentional, the output is
cluttered with the following message multiple times if the status of
the dsl line is queried:
killall: vdsl_cpe_control: no process killed
If the dsl line status is queried by LuCI, the logfile is spammed with
the message.
Fix the issue by using killall in quite mode. In quite mode killall
still returns a non-zero value if the to be killed process can not be
found so that existing logic based on the return value still works.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the introduced double whitespace the default package selection
isn't applied. This leads to errors like a not working networking
because of a missing swconfig binary.
Fixes FS#208.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add USB led aliases to boards having an led which is meant to be used
as USB led according to the manuals.
Remove the kmod-ledtrig-usbdev from the default package selection for
boards not having an USB led. Add the kmod-ledtrig-usbdev to boards
where it is missing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use a more generic name for the lantiq_get_dt_led_chosen function.
Drop the lantiq_is_dt_led_chosen function. The lantiq_get_dt_led
function can be used to achieve the same.
Signed-off-by: Mathias Kresin <dev@kresin.me>
It missed some changes needed for kernel 4.4. This is only used by the
Falcon SoC and not for the xRX SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Backport patches from upstream Linux kernel which are making the
kernel stores the appended dtb not in the same resisters as defined in
the UHI specification, use a separate variable on MIPS.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[some modifications]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto
Signed-off-by: Mathias Kresin <dev@kresin.me>
No functional change, it's just to have the same style everywhere. This
way I don't need to use any regex magic to extract all subtargets for
compile tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add or fix the physical port number of switch ports to allow LuCI to
display the ports in physical order.
Remove the physical port number in case bridge port and physical port
order are the same.
Reorder the ucidef_add_switch parameter to be aligned with the switch
port number.
Remove board settings which are covered by the default case and remove
comments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With 12fe4b5798 I switched the ath5k
eeprom extraction to an alternate code path. Unfortunately this code
seams to be broken since ages and broke the ath5k EEPROM extraction.
Reported-by: Mohammed Berdai <mohammed.berdai@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
GCC treats 24kc and 34kc exactly the same and will generate identical
code, so there is no need to tune to 34kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Device/AVM unconditionally inherits Device/NAND, which changes the
sysupgrade image to sysupgrade-tar (instead of a "raw" sysupgrade image
as used in the Device/Default template).
This moves the Device/NAND call to the FRITZ3370 device definition, as
this is the only AVM/EVA device that uses NAND.
Additionally we have to define the IMAGE_SIZE for the AVM/EVA NOR
devices to ensure that the images are not discarded.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Use priv->wan instead of priv->id as indicator if packets should go to the
Ethernet WAN group (DPID=1) or not (DPID=0). This way, it's independant of
interface names or indexes.
Signed-off-by: Martin Schiller <mschiller@tdt.de>
By default USB LEDs are associated with usbdev trigger. However,
not all devices which have USB LEDs have kmod-ledtrig-usbdev in their
list of default packages. Add it to the relevant devices.
Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
With an own DMA TX channel for each network device (eth0 + eth1) there
won't be any "tx ring full" errors any more.
This patch also move the spinlocks to the channel level instead of locking
the whole xrx200_hw structure.
Signed-off-by: Martin Schiller <mschiller@tdt.de>
According to the author of the cpu temp driver, not all xrx200 boards
have a cpu temperature sensor. For that reason enable the sensor only
for tested boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not set the lan mac address for boards which having the lan mac
address already set in device tree source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The device tree binding and the associated code duplicates functionality
already patched into the etop driver. The compatible string isn't used
any more. Therefore the whole code can be dropped.
The "mac-increment" property allowed to increment a mac address received
via kernel cmdline. This functionality isn't used by any device and
should be added as etop driver device tree property if required again.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the generic mtd-mac-address dts property to get a mac address from
flash instead of the lantiq specific one.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the same mac address increment in device tree source file and
userspace.
Don't add a mac address increment to either the only mtd mac-address or
to all mac-addresses.
Fix a typo in the TDW89X0.dtsi file to add an increment.
Signed-off-by: Mathias Kresin <dev@kresin.me>
All device tree nodes are using the named properties now and the code
path handling the reg property isn't required any more.
The code related to the ath,eep-flash property has been reformatted to
be better readable.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There does not seem to be any meaningful difference in generated code.
This will save some time and space on snapshot builds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The device tree description misses some Ethernet ports and there was no
model specified for this board. In addition there was no switch
specific default configuration created.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Andreas Eberlein
Mathias Kresin
Rafał Miłecki
Hauke Mehrtens
Álvaro Fernández Rojas
Jo-Philipp Wich
Martin Blumenstingl
Daniel Gimpelevich
Jonas Gorski
Sigurd Hogsbro
Martin Schiller
Matti Laakso
Felix Fietkau
Florian Eckert