The MR18 stores the ath9k eeprom values on the NAND.
This patch makes it possible to retrieve the images
from there.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47948
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
This adds support for specifying the dsl modem, atm bridge configs and setting
the pppoe protocol for wan.
These additions are required to port the Lantiq target to board.d.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47750
Some boards, e.g. the Sheeva Plug, require the lan interface to be set
to DHCP instead of a static address, therfore support that.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47732
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.
This change ...
* removes the reset and enable arguments from ucidef_add_switch()
* unconditionally writes reset:1 and enable:1 to JSON
* converts the three users of nonstandard values to ucidef_add_switch_attr()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47720
Remove support for now unused ucidef_add_switch_vlan(), move port->vlan and
vlan->interfaces conversion to uci-defaults-new.sh and massively simplify
config_generate.
This change prepares the following upcoming steps:
* Eliminate use of ucidef_set_interface_lan_wan() for switch only devices
* Merge ucidef_add_switch() with ucidef_add_switch_ports()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47719
Properly quote variables in ucidef_set_interface_lan() and
ucidef_set_interface_lan(), otherwise interfaces with multiple devices
are not properly written into the configuration.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47673
Add ucidef_set_board_id() and ucidef_set_model_name() procedures to store
model information in the board.json file.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47671
The only user was the hg255d board and config_generate did not even emit
proper uci for it.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47658
Remove extra nesting of rssi leds in the led object and move rssi monitor
declaration to its own object.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47655
Add further helper functions to uci-defaults-new.sh for easier declarations
of complex switch layouts.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47638
Even though there are not many users left within the OpenWrt tree it seems
this function broke during the kernel 3.18 transition.
Fix it by providing a workdir as required by overlayfs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47015
- Simplify user spec parsing code
- Alias IPKG_INSTROOT to shorten code
- Quote variables where appropriate
- Remove a useless-use-of-cat instance
- Suppress errors in case control or list files are missing
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46975
This enables passworldless login for root via SSH whenever no root
password is set (e.g. after reset, flashing without keeping config
or in failsafe) and removes telnet support alltogether.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46809
Using the postinst script for sanity checks and expecting opkg to fail
if the postinst didn't return 0 was possible in Barrier Breaker, propagate
the real postinst return code through default_postinst to restore this
behaviour.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46653
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
get_image allows passing 2nd argument that is used in a pipe for
extracting firmware from a non-native format. By accepting such command
in default_do_upgrade we allow platforms to use this helper for vendor
specific images.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45900
Instead of stripping everything after the first dot, strip everything
after the last dot.
This fixes pre-/postrm actions for packages with a dot in their name,
like libusb-1.0.
Fixes#19668.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45702
The name variable contains at first the package name,
and after the last group name.
This patch fixes /etc/rc.d symlink creation (at least).
Change name in pkgname, change the other name in ugname
(user group name), and id in ugid (user group id)
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 44253
This restores normal pre-r43715 200ms blink-period for the System LED we're all accustomed to see while our OpenWrt routers are booting.
Failsafe possibility will now be signalled with a new 100ms blinking, which is easily recognizable from the normal 200ms booting.
So no existing user will be scared by a new 500ms LED pattern, since such a slow pattern could easily be mistaken for something wrong... I was like "ok why my router is collapsing now, is this a bad flash, a kernel panic, or what else" when I've seen it for the first time ;)
Sorry for not having explained myself better in v1 of this patch.
Original:
Preinit, failsafe is possible: 200ms
Preinit, failsafe not possible anymore, booting normally: 200ms
Failsafe entered: 50ms
Now (after preinit_regular has been introduced):
Preinit, failsafe is possible: 200ms
Preinit, failsafe not possible anymore, booting normally: 500ms *here is the "offending" change*
Failsafe entered: 50ms
With my proposed patch:
Preinit, failsafe is possible: 100ms *indicate this condition with a new timing, that prompts the user to press the key if they want to start failsafe*
Preinit, failsafe not possible anymore, booting normally: 200ms *keep this as before*
Failsafe entered: 50ms
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 44056
The enable and reset settings need to be added even when they're false. This is true at least for 'enable', that seems to default to true otherwise.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43887
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
create user:group before running postinst-pkg. the postinst hook might require
the user:group to already exist.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 43472
ldd might be called for shell scrips during sysupgrade, causing it to
complain that they are not a dynamic executables.
This is a harmless error, so supress it to avoid confusing about them
being serious ones.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43315
Felix Fietkau
Jo-Philipp Wich
John Crispin
Steven Barth
Jonas Gorski
Luka Perkov