The 3.10.x infrastructure has been present for some time, and seems to
run fine here.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 39483
It was recently sent to linux-mips for comments. It adds workaround for
WNR3500L to enable USB port.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 39469
This does not add any new features, just some changes to the patches
and a first try to use dt to set the irqs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39466
The original dragino2 board support was missing some changes from the
upstream svn repository (http://svn.dragino.com/dragino2) that supported
sysupgrade.
[juhosg: change subject]
Signed-off-by: Karl Palsson <karlp@remake.is>
Patchwork: http://patchwork.openwrt.org/patch/4801/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39429
Since the yaffs code update (r39084), it is not
possible to install OpenWrt on RouterBoards with
small-page NAND chips. Fix the yaffs code to make
it work again.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39409
The 3.6 kernel isn't used by any of the x86 subtargets, so remove it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39403
Use the 'swconfig_trig_set_brightness' function to set
the brightness value of the LED when the link goes down.
This ensures that the last brighness value is saved into
a local variable which is used to track the actual LED
status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39402
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39392
Get the size of the mtd partitions directly from the
MTD layout and remove the superfluous macro parameters.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39384
The macro checks the size of the rootfs image even if
the second parameter of the macro contains the size of
an eraseblock. It is wrong because the size of the
kernel image will be adjusted to the next eraseblock
and the resulting image might be too large.
Fix the macro to check the size of the final image
instead of the rootfs image.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39383
This reverts r38197.
The automatically created firmware partition includes
the partition_table partition. Apart from the partition
table, this partition contains sensitive data on some
Compex devices which data can be destroyed when the
firmware partition gets modified. Revert the change to
prevent that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39382
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39373
The default inittab uses "askconsole" which is implemented by procd
and uses the console provided by the kernel command line.
Hence, this platform specific workaround is not necessary anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39367
Add kernel support for the BCM963269BHR board, USB and Ethernet switch,
LEDs and buttons are working.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39363
Allow using the HSSPI controller since it works just fine, as well as
the integrated switch core, since that one works too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39362
Hauke Mehrtens
Zoltan Herpai
Felix Fietkau
Gabor Juhos
Florian Fainelli
Luka Perkov