This prevents generating every supported image, except for de "Default" profile.
Also fixes Neufbox 6 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42210
Use generic profiles for brcm63xx instead of having similar profiles for
each subtarget.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42208
This changes board info to match the Wiki
http://wiki.openwrt.org/toh/huawei/hg556a, removes the no longer needed
fallback board and fixes HG556 Ralink eeprom extraction.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: rename partitions instead]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42206
There is a group of devices that lzma-loader doesn't work with. They
simply hang at "Starting program at 0x80001000" which is really hard to
debug and we didn't find any solution for this for years.
Broadcom doesn't use lzma-loader on these devices anyway. They decided
to drop lzma-loader and use less optimal LZMA compression that can be
handled by CFE itself (it doesn't use dictionary).
So support these devices we will need kernel compressed with different
parameters and trx without a loader.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42205
Switch in Edimax 3G-6200n also require full switch reset, not only vlan definitions. Tested on Edimax 3G-6200n.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42194
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42193
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42184
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42180
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 42179
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.
Tested on hardware.
[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 42178
The conversion was not 100% correct and leads to u-boot failing to
verify the CRC, revert that change for now.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42170
This patch is causing more harm than good on most AR7 routers out there,
better have no manageable switch rather than no ethernet connection, at
least for now.
Fixes#16523, #5927
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42168
Jonas Gorski
John Crispin
Hauke Mehrtens
Florian Fainelli
