Commit Graph

33400 Commits (2c4faaed7440687a027cfd9bdd592411b0c460f5)

Author SHA1 Message Date
John Crispin ec21c9821c lantiq: Configure disabled WLAN bands for TDW89X0.
The TDW8970 has a AR9381, which is the bgn 3x3:3 variant of the AR938x family.

The TDW8980 has a AR9287, which is the bgn 2x2:2 variant of the AR928x family.

This means that the chip for both routers is 2.4 GHz only.

Anyway, the manufacturer didn't disable the 5 GHz band in the EEPROM partition
(at least on my TDW8970).

So this patch disables the 5 GHz band.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47912
2015-12-17 09:27:40 +00:00
John Crispin f2fd516d72 lantiq: Allow configuration of ath9k disabled bands and LED polarity from the device tree.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47911
2015-12-17 09:27:31 +00:00
John Crispin 932bc8d5eb ath9k: Allow configuration of LED polarity in platform data.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47910
2015-12-17 09:27:24 +00:00
John Crispin 4a4b0b82ec ath9k: Pass LED polarity to ath_create_gpio_led when initializing the LEDs.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47909
2015-12-17 09:27:18 +00:00
John Crispin 7de7bd0201 ramips: mt7621: fix error message when initramfs is too large
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47908
2015-12-17 09:27:09 +00:00
John Crispin 1c5136c4c3 ramips: remove unwanted change from patch
Remove unwanted change to irq-mips-gic.c from mt7621 support patch

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47907
2015-12-17 09:27:00 +00:00
John Crispin 43422a634b ramips: change CM_GCR_BASE_CMDEFTGT_MEM value to match datasheet
Zero config value for default memory region means 'memory', not
not 'disabled' according to 'Control Registers Of The Coherency
Manager' manual.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47906
2015-12-17 09:26:51 +00:00
John Crispin acbed0eff3 ramips: mt7621: undo mips-cm probe hack to not wipe out memory regions
Since now we hopefully setup memory regions properly we no longer need this hack.

Tested and works on ubnt-erx.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47905
2015-12-17 09:26:43 +00:00
John Crispin 622e268710 ramips: mt7621: setup memory region for pcie controller memory
Only compile tested since I do not have any hardware with
devices on pcie bus.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47904
2015-12-17 09:26:35 +00:00
John Crispin e8890c6be0 ramips: mt7621: add patch to setup CM memory region for palmbus
This is tested and works on ubnt-erx.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47903
2015-12-17 09:26:28 +00:00
John Crispin b4bb10b3a0 ralink: update config files to build the cleaned up ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47902
2015-12-17 09:26:20 +00:00
John Crispin 402db12f1a ralink: drop dummy profile from mt7688
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47901
2015-12-17 09:26:09 +00:00
John Crispin 651e620de5 ralink: fixup devicetree files to work with new ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47900
2015-12-17 09:25:57 +00:00
John Crispin fa854a02a1 ralink: drop old ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47899
2015-12-17 09:25:30 +00:00
John Crispin 31116661ff ralink: add reworked ethernet driver
update to the version of the driver that is on its way upstream

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47898
2015-12-17 09:25:24 +00:00
Felix Fietkau a99c78a09a netifd: update to the latest version, fixes more route table issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47897
2015-12-16 23:15:15 +00:00
Rafał Miłecki 716905b986 bcm53xx: print bcm47xxpart buf to debug R8000 UBI problem
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47896
2015-12-16 09:37:16 +00:00
Imre Kaloz 5705d058eb generic/4.4: bump to -rc5
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 47894
2015-12-15 11:20:38 +00:00
Felix Fietkau 513702e658 netifd: update to the latest version, fixes reload issues on routing table changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47893
2015-12-15 11:01:47 +00:00
Felix Fietkau 6505dc3367 ar71xx: clean up ethernet tx queue after reset, wake queues when done - fixes hangs reported in #18922
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47892
2015-12-14 20:22:09 +00:00
Felix Fietkau 510f5a7209 linux-atm: add wrapper for br2684ctl to defer nasX device bringup
Fixes a race condition on netifd device bringup.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47891
2015-12-14 11:02:12 +00:00
Felix Fietkau c0f4c9e0d8 include/netfilter.mk: fix kmod-ipt-tee build with 4.3/4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47890
2015-12-13 18:33:11 +00:00
Felix Fietkau 6b87e0706d ar71xx: Update merakinand.sh to fix sysupgrade
Remove reliance on /lib/upgrade/nand.sh as this is called by sysupgrade,
based on felix's comments at
https://lists.openwrt.org/pipermail/openwrt-devel/2015-December/037963.html

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47889
2015-12-13 18:05:42 +00:00
Felix Fietkau be00acca5a lantiq: ltq-vdsl-app: cleanup Makefile
- CONFIG_IFX_CLI is unused, couldn't find any reference to this config variable
- use disable-feature instead of enable-feature=no
- reorder configure args to have depending args together
- remove configure args which set the default value
- group enable-model and configure args which enable or disable features that
  are covered by the feature set

The config.log contains the same values as before. The vdsl_cpe_control binary
has the same checksum as before.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47888
2015-12-13 17:04:12 +00:00
Felix Fietkau d984e3836f lantiq: ltq-vdsl-app: re-add showtime counters support
The typicial feature set doesn't include "DSL PM showtime counters support"
(INCLUDE_DSL_CPE_PM_SHOWTIME_COUNTERS). This feature provides the
vdsl_cpe_control command 'pmccsg', which is used by 'dsl_control status' to get
the line uptime.

The binary size increases to 103912 byte (+4256 byte) uncompressed.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47887
2015-12-13 17:04:02 +00:00
Felix Fietkau ce98f1d264 base-files: drop the now unnecessary dependency on opkg/host
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47886
2015-12-13 17:03:51 +00:00
Felix Fietkau ce6c1c6c84 build: add opkg host dependency
fixes a missing host opkg
found by: unselect base-files, opkg

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 47885
2015-12-13 17:03:40 +00:00
John Crispin 5d4f5689fd ramips: add missing kernel symbols
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47884
2015-12-12 21:01:02 +00:00
Felix Fietkau f0664d34a6 kernel: make kmod-crypto-rng depend on kmod-crypto-hash
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47883
2015-12-12 12:02:20 +00:00
Felix Fietkau bb52e2e1ef ar71xx: add rx/tx delay definitons for qca955x's MAC
This patch adds the rx/tx register offsets for the qca955x SoC.

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47882
2015-12-12 11:27:51 +00:00
John Crispin 4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
John Crispin 1c6c9549d6 ramips: add support for Spansion S34ML0[24]G2 flash
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47880
2015-12-12 07:37:53 +00:00
John Crispin f99c61a94a procd: add 'platform_nand_pre_upgrade'
Add 'platform_nand_pre_upgrade' callback to allow platform specific
preparation right before flashinng, when already in ramdisk.

Example uses might be setting correct values for CI_{KERNPART,UBIPART}.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47879
2015-12-12 07:37:45 +00:00
John Crispin abc84551c0 ar71xx: add support for Cisco's MR18
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47878
2015-12-12 06:42:29 +00:00
John Crispin 9e5044926b ralink: remove stray "+" from ethernet driver
this is what you get if you manually apply patches with c&p

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47877
2015-12-12 06:42:17 +00:00
John Crispin 8470e30a76 ramips: move partition definitions out of mt7621.dtsi file
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47876
2015-12-12 06:42:11 +00:00
John Crispin e610cdfc8a ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47875
2015-12-12 06:42:05 +00:00
Felix Fietkau 0b6271faf4 ar71xx: reorganize target patches/files to make it possible to add boards without adding patch files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47874
2015-12-11 21:12:14 +00:00
Felix Fietkau 0186d4c2c2 ar71xx: on wnr2200, revert the mac0/mac1, the ethernet interfaces are swapped. use MAC1 for wlan
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47873
2015-12-11 21:12:04 +00:00
Felix Fietkau 77bedbe80d Revert "ramips: use gic timer as clocksource for mt7621"
This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7.

SVN-Revision: 47872
2015-12-11 19:22:15 +00:00
Felix Fietkau 6e12ef7430 ar71xx: fix MAC address swapping on WNR2200 and fix the WLAN MAC address
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47871
2015-12-11 19:21:59 +00:00
Felix Fietkau 84a56a7849 kernel: crypto-aead depends on crypto-null in 4.3 as well
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47870
2015-12-11 19:21:49 +00:00
Felix Fietkau d437c72c21 tools/squashfs4: refresh patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47869
2015-12-11 19:21:43 +00:00
Felix Fietkau e5c1cc5545 build: for refresh, override HOST_QUILT like QUILT
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47868
2015-12-11 19:21:29 +00:00
Jo-Philipp Wich 67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
Jo-Philipp Wich b0b8293b7e brcm47xx: migrate network config to board detection framework
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47866
2015-12-11 15:19:43 +00:00
John Crispin 244173a093 firmware-utils: fix various compiler warnings
mostly implicit defines due to missing includes plus one const that
shouldn't be one.

Signed-off-by: Felix Kaechele <felix@kaechele.ca>

SVN-Revision: 47865
2015-12-11 15:09:30 +00:00
John Crispin 0231d41352 mktplinkfw: add missing exceeding bytes info to logs
Add the info on exceeding bytes also to the remaining log messages.

Signed-off-by: Felix Kaechele <felix@kaechele.ca>

SVN-Revision: 47864
2015-12-11 15:08:44 +00:00
John Crispin 786717a7ce uboot-lantiq: fix build with gcc5
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47863
2015-12-11 15:08:34 +00:00
John Crispin 32b37600b9 procd: update procd.sh to support new ujail options
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>

SVN-Revision: 47862
2015-12-11 15:08:19 +00:00