Add support for the ADT7410 hwmon driver, a high precision
I2C temperature sensor.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
[juhosg: update subject, reformat commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38186
Move pca953x support from i2c.mk to other.mk, where other
GPIO drivers are located. Remove duplicate pcf857x support
from i2c.mk.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
[juhosg: update subject, and reformat commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38185
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38036
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38001
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37977
Most of the Linksys devices without an own GPIO configuration where
detected as WRT54G. On one board this made OpenWrt to boot into
failsafe every time, because one GPIO configurated as button was not a
button.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37970
The imx sata module has only been backported to imx6 target. This change will
fix buildbot errors due to missing patches in other targets. Keep this until
all targets use kernel version with imx sata support in them.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37950
This fixes the following error:
keyspan: Unknown symbol ezusb_fx1_ihex_firmware_download (err 0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37899
This enables usage of the ath10k driver on OpenWrt. Only 2.0 PCI hardware
is supported. The ath10k firmware is currently only available
through github so use that as its source for now.
This goes build tested, not run time tested.
[Hauke: I did some minor changes]
Cc: ath10k@lists.infradead.org
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Mathieu Olivari <mathieu@qca.qualcomm.com>
Cc: Jerome Proffit <jproffit@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Matthew McClintock <mmcclint@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37898
The package makes it possible to create custom SPI
buses via GPIO lines.
This module is based on i2c-gpio-custom and allows to
configure an SPI bus via GPIO lines and expose it to
userspace without rebuilding the kernel. This is maily
intended to connect microcontrollers and other simple
SPI devices without making an ad-hoc kernel driver.
Signed-off-by: Marco Burato <zmaster.adsl@gmail.com>
[juhosg:
- change subject,
- extend and reformat commit message,
- cleanup checkpatch errors/warnings in module source]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37872
Backport some rt2x00 specific changes from
wireless-testing/master-2013-08-26 to add
support for RT3573 based devices.
Also refresh the rt2x00 specific patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37843
Gabor Juhos
Felix Fietkau
John Crispin
Hauke Mehrtens
Luka Perkov
Steven Barth