This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Ports: 1 GbE port (PoE in)
WLAN: 5 GHz QCA899X (PCI)
The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).
Installation procedure is the same as the NanoStation [loco] AC:
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The image build code for the Ubiquiti Nanostation AC series adds the
factory image as to be build image. The same is already done by an
included recipe which results into an expanded IMAGE variable of:
IMAGES = sysupgrade.bin factory.bin factory.bin
The build system doesn't like these duplicates and issues the following
warning:
Makefile:82: warning: overriding recipe for target...
Get remove the duplicate factory image to get rid of the warning.
Fixes: 5736af8024 ("ath79: Add support for Ubiquiti NanoStation AC loco")
fa3c2676ab ("ath79: Add support for Ubiquiti Nanostation AC")
Signed-off-by: Mathias Kresin <dev@kresin.me>
5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Switch: QCA8334
Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough)
WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342
Successor to the old NanoStation M5 with AC wireless.
The integrated QCA899X is a Ubiquiti branded part with modified vendor and
product id (0777:11ac9).
Serial
Serial settings: 115200, 8N1
* = plated through hole
0 = nylon screw
[Top of device]
+--------------------------+
| [label] |
| 0 |
| 0 |
| [ubnt] |
| [logo] 3V3 * |
| TX * |
| RX * |
| GND * |
| |
| * |
| * |
| * |
| * |
| 0 |
| 0 |
| |
| |
Installation
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
Atheros AR9342, 16 MB flash, 64 MB RAM
Successor to the old NanoStation M5 loco with AC wireless.
Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti
branded and customized QCA988X with vendor id 0777 and device id 11ac for
AC wireless.
Installation
1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
We select ath10k-ct by default, but it is still possible to build
the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM family.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other
.dts files that utilize it, ar7161_ubnt_routerstation.dts and
ar7161_ubnt_routerstation-pro.dts.
The modifications to generic-ubnt.mk, config-default, and base-files
necessary for image generation, parsing RedBoot FIS partitions, network
configuration, and sysupgrade are also included.
This reintroduces vital bits from platform_do_upgrade_combined() and its
supporting functions to /lib/upgrade/platform.sh, which were previously
removed from ath79 in 3e9d9f6225 "ath79:
sysupgrade: drop unused platform checks". The new function is called
"routerstation_do_upgrade" and will *only* work for the RouterStation
series of boards. It does however retain the ability to downgrade (e.g.
from master -> 17.01.x using sysupgrade -F).
All hardware is functional including the AR8216 switch (for the Pro),
wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button,
and LED.
Switch and LAN/WAN configuration is the same as it is with the
equivalent ar71xx targets. MAC addresses are assigned based upon the
content stored in the RedBoot config partition.
Flashing via both sysupgrade and TFTP has been confirmed to work. Also,
the initramfs images are now raw .bin files instead of being wrapped in
a uImage (as they currently are in ar71xx), which makes them bootable
with RedBoot.
One notable difference to ar71xx is the inclusion of the RedBoot
"fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in
DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD
parser’s DT binding, whose proper usage is mutually exclusive to
defining a separate fixed-partitions node for "RedBoot config". This
config partition contains the board's base MAC address. The lack of a
hard-coded flash location means that the mtd-mac-address property cannot
be used in the .dts, so instead fconfig is used to read the MAC
addresses from flash in userspace during first boot.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
The Unifi AC Mesh is equivalent to the Unifi AC Lite. However,
for setting certain parameters with the flashed device it is
helpful that the devices know their variant (e.g. automatically
setting antenna gain for the different antennas in Lite and Mesh).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
rework the dts to a common unifi-ac dtsi
pro network is connected via phy0 and has usb ports
lite network is connected via phy4 without usb ports
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Remove recipes for not yet migrated boards. Drop variables which aren't
required due to the switch to devicetree like boardname.
Drop the legacy image build code. Boards added to this target shouldn't
use the legacy image build code anyway.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the SoC compatible to the individual dts files. Rename the dts files
to match the common pattern.
Remove dts files wich aren't used and no image in ar71xx exists.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.
Signed-off-by: John Crispin <john@phrozen.org>
Roger Pueyo Centelles
Mathias Kresin
Tobias Schramm
John Crispin
Lech Perczak
Matt Merhar
Christoph Krapp
Adrian Schmutzler
Lucian Cristian
Matthias Schiffer