5178c177dc
rebase config-3.3
...
SVN-Revision: 32797
2012-07-24 17:28:25 +00:00
48869ef7c0
move CONFIG_ETHERNET_PACKET_MANGLE to a generic config file
...
This broke falcon builds
SVN-Revision: 32794
2012-07-24 15:33:01 +00:00
95e69ac4f1
clean up generic image building
...
SVN-Revision: 32065
2012-06-05 17:49:42 +00:00
a4d96aae8d
bump to 3.3.8
...
SVN-Revision: 32055
2012-06-05 06:57:51 +00:00
7f00e5ffc6
uboot-envtools: update to 2012.04.01
...
SVN-Revision: 32051
2012-06-04 21:55:49 +00:00
2b4ef2eafa
adds unset Kbuild symbol
...
SVN-Revision: 32026
2012-06-02 14:03:32 +00:00
47ef62d1b8
adds patch to make Tantos (psb6970) switch buildable again
...
SVN-Revision: 32006
2012-05-30 17:41:28 +00:00
ff74305623
lantiq: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31995
2012-05-29 16:39:21 +00:00
f567980d38
move files-3.3 -> files
...
SVN-Revision: 31912
2012-05-27 16:13:02 +00:00
8002770520
3.2 R.I.P.
...
SVN-Revision: 31911
2012-05-27 16:12:59 +00:00
81ddc886e1
dgn3500 support with eeprom loading from sysfs
...
WIFI eeprom:
As discussed, it is impossible for nand and spi flash platforms to have the eeprom data available from mtd. I suggested to load the eeprom from user-space. I've looked into regular firmware loading but this is only possible when using modules. I've created a sysfs entry that allows reading and writing the eeprom data to the platform data. After loading the eeprom data I rely on pci-hotplug support to disable the bogus pci device and rescan the bus (with fixups and all). Because hotplug is not available, an init script is created that performs the copy from mtd to platform data. I think it is best to eventually move the sysfs functions to dev_wifi_athxk.c file, this would get rid of the external to the ath9k platform data.
SPI flash:
It seems that the spi-xway driver is not really working. It causes my kernel to crash in all sorts of ways. I added to bitbang SPI to be able to the calibration data mention above.
I've kept the original mtd partitioning that Netgear uses.
Buttons/LED:
Both buttons are working properly. Two leds are not enabled: The red internet led is connected to the pci_gnt1 pin... I can't disable it because then DMA stops working.
The green wifi led is connected to an unknown atheros gpio.
Signed-off-by: Pieter Voorthuijsen <p.voorthuijsen at gmail.com>
SVN-Revision: 31910
2012-05-27 16:02:22 +00:00
6e8fe84472
fixes zyxel p2601hnfx
...
moves the linux partition, removes the config partition and the
buttons settings have small adjustments.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31909
2012-05-27 16:02:20 +00:00
3f2f50c681
Add basic configuration for new board ZTE H201L. Still missing are button and led gpio values.
...
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31908
2012-05-27 16:02:16 +00:00
2ae5581447
kernel: update linux 3.3 to 3.3.7
...
SVN-Revision: 31848
2012-05-23 21:05:32 +00:00
9037c2ccc6
lantiq: allow platforms with rt2x00 to override the mac address without overriding eeprom, fixes bogus wlan mac address on arv4520
...
SVN-Revision: 31835
2012-05-20 21:58:03 +00:00
39994008cb
linux: move certain disabled symbols to the generic configs
...
* CONFIG_ARCH_DMA_ADDR_T_64BIT
* CONFIG_ARCH_HAS_ILOG2_U32
* CONFIG_ARCH_HAS_ILOG2_U64
* CONFIG_ARCH_PHYS_ADDR_T_64BIT
* CONFIG_ARCH_SUPPORTS_MSI
* CONFIG_GENERIC_CPU_DEVICES
* CONFIG_HWMON_DEBUG_CHIP
* CONFIG_I2C_PXA_PCI
* CONFIG_LEDS_GPIO
* CONFIG_MINIX_FS_NATIVE_ENDIAN
* CONFIG_MLX4_CORE
* CONFIG_POWER_SUPPLY
* CONFIG_POWER_SUPPLY_DEBUG
* CONFIG_QUOTACTL
* CONFIG_SDIO_UART
* CONFIG_SENSORS_K10TEMP
* CONFIG_SENSORS_SCH56XX_COMMON
* CONFIG_SENSORS_VIA_CPUTEMP
* CONFIG_SERIO_AMBAKMI
* CONFIG_SERIO_I8042
* CONFIG_SERIO_LIBPS2
* CONFIG_SERIO_PCIPS2
* CONFIG_SERIO_RAW
* CONFIG_SERIO_SERPORT
* CONFIG_SPI_BITBANG
* CONFIG_SPI_GPIO
SVN-Revision: 31737
2012-05-15 10:58:52 +00:00
364f47e454
code style cleanup of the mach files
...
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31735
2012-05-15 09:38:05 +00:00
07dca108a9
adds zyxel p2601hnfx support
...
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31734
2012-05-15 09:38:02 +00:00
9785ec070e
set 3.3.6 as default
...
SVN-Revision: 31733
2012-05-15 09:37:59 +00:00
c61ada1db8
set 3.3.5 as default
...
SVN-Revision: 31718
2012-05-14 16:11:26 +00:00
b472e5d12e
kernel: update linux 3.3 to 3.3.6
...
SVN-Revision: 31709
2012-05-14 09:18:32 +00:00
dc4cfd3a64
Add 3.3 config files
...
SVN-Revision: 31672
2012-05-09 12:52:24 +00:00
75827c538d
Add missing 3.3 patches
...
SVN-Revision: 31671
2012-05-09 12:52:21 +00:00
7d638fbb2f
Drop 2.6.32 support
...
SVN-Revision: 31670
2012-05-09 12:52:19 +00:00
34018a630f
kernel: update linux 3.3 to 3.3.5
...
SVN-Revision: 31645
2012-05-07 20:11:43 +00:00
0ff3c396d3
kernel: rewrite the phy packet hook, put it in the network stack to avoid having to keep non-upstream ethernet driver changes
...
SVN-Revision: 31637
2012-05-06 21:19:14 +00:00
cbfce53831
kernel: update linux 3.3 to 3.3.4
...
SVN-Revision: 31541
2012-04-30 08:38:11 +00:00
22b4e6b882
kernel: update linux 3.2 to 3.2.16
...
SVN-Revision: 31459
2012-04-24 09:25:35 +00:00
d4f3677cba
Adding wifi eeprom extract for ARV752DPW - Easybox 802
...
Signed-off-by: Christian Rustmeier <rustmeier a.t. gmail dotty com>
SVN-Revision: 31443
2012-04-23 09:40:37 +00:00
87cdc0dd5b
change /etc/config/network according to actual VLAN config to enable LAN port 4 on the ARV4520PW board
...
The VLAN mapping on the ARV4520PW board is the following:
port on Router: | VLAN in software:
LAN 1 | 3
LAN 2 | 2
LAN 3 | 1
LAN 4 | 0
DSL | 4
So LAN4 is not VLAN4 but VLAN0 (VLAN4 is DSL port) -> set "3 2 1 0 5t" as default switch config.
SVN-Revision: 31391
2012-04-21 08:07:21 +00:00
a8f2bc682e
kernel: also update the targets to use 3.2.15
...
Thanks Gabor for spotting it.
SVN-Revision: 31337
2012-04-17 13:12:14 +00:00
3a9b6dc313
kernel: update linux 3.3 to 3.3.2
...
SVN-Revision: 31336
2012-04-17 12:51:02 +00:00
ee4c47a134
kernel: update linux 3.2 to 3.2.15
...
SVN-Revision: 31335
2012-04-17 12:50:54 +00:00
83948d6385
adds 3.3 patches and files
...
SVN-Revision: 31307
2012-04-16 12:31:48 +00:00
e3889bcf7c
update 3.2 patches
...
sync with lantiq kernel series
SVN-Revision: 31260
2012-04-12 12:33:56 +00:00
16b4cbcdd6
kernel: update linux 3.2 to 3.2.14
...
SVN-Revision: 31222
2012-04-09 14:48:51 +00:00
da3f3f8f9d
add Easybox 802 - ARV752DPW
...
Implements the ARV752DPW architecture in mach-arv.c
Signed-off-by: Christian Rustmeier <rustmeier@gmail.com>
SVN-Revision: 31206
2012-04-05 20:03:21 +00:00
94af65db49
enable usb on dgn3500
...
A power-enable toggle gpio is not available, it is always on and protected with a resettable fuse.
Signed-off-by: Pieter Voorthuijsen<p.voorthuijsen at gmail.com>
SVN-Revision: 31205
2012-04-05 20:03:19 +00:00
d87efd8c3c
kernel: update linux 3.2 to 3.2.13 and refresh patches
...
Also remove a duplicate patch from lantiq (already in generic).
SVN-Revision: 31158
2012-04-01 07:56:55 +00:00
5f799a0e97
ath9k: make endian check optional
...
Turns out it triggers on some AR71xx devices where no swapping should be done.
Enable endian check for the lantiq target.
SVN-Revision: 31084
2012-03-27 13:21:53 +00:00
b982e8166b
cleanup atheros wifi handling
...
Signed-off-by: Andrej Vlašić <andrej.vlasic0@gmail.com>
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31064
2012-03-25 08:50:38 +00:00
5ea100c39b
cleanup image makefile
...
SVN-Revision: 31063
2012-03-25 08:50:32 +00:00
f27c030141
update /etc/uci-defaults/*
...
SVN-Revision: 31062
2012-03-25 08:50:30 +00:00
ba4a7fca7b
update profiles
...
SVN-Revision: 31061
2012-03-25 08:50:27 +00:00
0f6a9d5c7c
bump kernel to 3.2.12
...
SVN-Revision: 31060
2012-03-25 08:50:09 +00:00
db6e326c56
targets: replace madwifi in profiles with ath5k, madwifi is unmaintained
...
SVN-Revision: 31015
2012-03-19 09:58:13 +00:00
fab5be9b4f
lantiq: load dwc_otg early
...
Needed for using external rootfs on usb sticks.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SVN-Revision: 30940
2012-03-14 10:59:52 +00:00
e5798d7c9b
fixes etop locking issue
...
SVN-Revision: 30689
2012-02-23 07:42:00 +00:00
1a71f07d00
generate uboot environment data in target
...
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.
uboot environment config is used by fw_printenv fw_setenv tools.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 30537
2012-02-14 19:07:11 +00:00
7416a5f0aa
fix compile error in previous commit
...
SVN-Revision: 30534
2012-02-14 19:07:05 +00:00
John Crispin
Luka Perkov
Gabor Juhos
Felix Fietkau
Jonas Gorski
Mirko Vogt