36e862da17
lantiq: vgv7519: fix board_config on dts, read mac address and set
...
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
SVN-Revision: 43109
2014-10-29 20:50:40 +00:00
4d7ae64b73
vgv7519: support more recent board release with vrx288 v1.2
...
The existance of this new board has been confirmed and tested by the guy on this commit
76fdd8e638
2014-10-26 17:18:41 +00:00
0f790247e3
lantiq: allow pcie to be disabled by dts + vgv7519 fix pci irq + disable pcie by dts
...
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
SVN-Revision: 42907
2014-10-14 11:04:25 +00:00
c085d07ee3
lantiq - vgv7519: load rt5362 eeprom from bootloader param patition
...
SVN-Revision: 42824
2014-10-06 20:08:30 +00:00
6a961da231
lantiq - vgv7519: enable pci bus
...
SVN-Revision: 42823
2014-10-06 20:08:18 +00:00
c2e4007bc1
lantiq - vgv7519: remove spi_cs4, since the board use this line for something else
...
SVN-Revision: 42822
2014-10-06 20:08:11 +00:00
4cdf861521
lantiq - vgv7519: fix open-drain configuration for stp
...
SVN-Revision: 42821
2014-10-06 20:08:04 +00:00
1e7962ceaf
lantiq - vgv7519: add pci-rst entry into dts
...
SVN-Revision: 42820
2014-10-06 20:07:56 +00:00
ea9aec2fa9
lantiq - vgv7519: remove exin definition copied from dev-board dts
...
SVN-Revision: 42819
2014-10-06 20:07:45 +00:00
9483a322dd
lantiq - vgv7519: we don't have pcie bus so we don't need the reset device tree for this board
...
SVN-Revision: 42818
2014-10-06 20:07:30 +00:00
48d67fe650
lantiq - vgv7519: we don't have dual minipci-card so we don't need gnt1-req1 for pci handling
...
SVN-Revision: 42817
2014-10-06 20:07:19 +00:00
d0606948cb
lantiq - vgv7519: fix gphy led configuration (this set correct alt function to gpio and let peripherials on pci bus to comes up)
...
SVN-Revision: 42816
2014-10-06 20:07:04 +00:00
3dd93e8336
lantiq: move the lantiq,switch property into the interface node
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42574
2014-09-16 14:53:01 +00:00
e47fbcbf1d
lantiq: BTHOMEHUBV2B use bigger mtd partition for kernel
...
The bb-rc3 image for the BTHOMEHUBV2B is too big for its
mtd partition. This patch corrects the partition sizes in
the device tree. This patch should really go in before
bb-final, otherwise the BTHOMEHUBV2B images won't be useable.
I do apologise for not spotting this straight away.
Many thanks,
Ben
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 42316
2014-08-28 06:27:41 +00:00
b796ff6ef3
lantiq: generate unique ARV7519RW22 firmware
...
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42183
2014-08-18 13:09:11 +00:00
5f71dbb005
lantiq: improve ARV7519RW22 support
...
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42180
2014-08-18 13:08:56 +00:00
c21a20cd78
lantiq: fix dgn3500 and td8970 wifi
...
ath9k failed to come up due to a bad mac addr
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41860
2014-07-28 15:26:41 +00:00
4beb468f11
lantiq: fix board_id/boardname for VGV7519
...
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
SVN-Revision: 41672
2014-07-16 11:36:02 +00:00
85cacfd753
lantiq: vgv7519 add missing wps label to dts
...
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
SVN-Revision: 41655
2014-07-14 18:43:02 +00:00
85ca75decd
lantiq BTHOMEHUBV2B - update dts for automatic detection of ubi partition and rootfs type
...
This patches the BTHOMEHUB2B device tree to make use of the
new code for automatic detection of the ubi partition and the
rootfs type within it. Gets rid of the ugly alternative bootargs
lines.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41214
2014-06-16 18:54:38 +00:00
e6c46554bb
lantiq: fixup vgv7519 usb support
...
https://dev.openwrt.org/ticket/16800
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41213
2014-06-16 18:54:33 +00:00
7ba5188fe9
lantiq: Fix ARV7510PW22 etop
...
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40920
2014-06-02 12:43:43 +00:00
d4ec98c2cc
lantiq: Fix ARV4518 etop
...
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40919
2014-06-02 12:43:35 +00:00
4f3c740110
lantiq: BT Home Hub 2B - overlayfs on top of ubi
...
BT Home Hub 2B: use overlayfs on top of ubi.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 40553
2014-04-22 08:08:46 +00:00
c4aae8fbc5
lantiq: ARV7519RW22: several fixes
...
- Fix ethernet ports.
- Clean DTS files.
- WiFi is lantiq based (not supported yet), remove ath9k.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40519
2014-04-16 12:01:09 +00:00
9fbbd04f45
lantiq: enable switch on td8970
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40498
2014-04-12 21:22:21 +00:00
60edb8f47b
lantiq: add an extra partition to the TDW8970 flash that can be used to store the vdsl firmware
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40461
2014-04-11 20:40:34 +00:00
858b972e66
lantiq: there is a V2 of VG3503J that needs a newer fe phy firmware
...
this should really be auto detected by the kernel, lets used this workaround until the real
solution is ready
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40418
2014-04-07 15:10:22 +00:00
709cab91d2
lantiq: BT Home Hub 2B support - board support
...
Board support patch for BT Home Hub 2B
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 40370
2014-04-03 14:26:54 +00:00
78a7ae428f
lantiq: make td8970 wifi led work
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40368
2014-04-03 14:26:46 +00:00
58eccdac4f
lantiq: fix vr9 ubi handling
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40364
2014-04-03 14:26:24 +00:00
e36568e74b
lntiq: add support for Astoria ARV7519RW.
...
These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.
Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 40329
2014-03-30 10:02:30 +00:00
5a98a6b9cf
lantiq: P2601HNFX dts update for STP and buttons
...
- Set correct AltSel for STP pins
- Set front button to rfkill
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40320
2014-03-30 09:16:19 +00:00
e733242a23
lantiq: add support for Arcadyan ARV7519PW
...
This patch adds almost full support for this board.
- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40319
2014-03-30 09:16:15 +00:00
9531390aad
lantiq: add support for ZyXEL P2812HNUFX
...
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40317
2014-03-30 09:16:06 +00:00
93e5c8cefc
lantiq: fixup 3370 dts file
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40311
2014-03-30 09:15:41 +00:00
eddc327c7c
lantiq: fix PCI problems on ARV4510PW
...
Some ARV4510PW units seem to have unstable PCI due to missing pull-up
resistors. This patch makes sure that the GPIO lines are driven properly.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 39587
2014-02-15 22:54:32 +00:00
053d596297
lantiq: Add support for Astoria ARV7510PW22
...
This board is pretty similar to ARV752DPW22.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 39303
2014-01-15 19:16:51 +00:00
f58b424c9e
lantiq: improve Arcadyan ARV4510PW support
...
Arcadyan ARV4510PW has already a build profile in OpenWrt, but it is
severely lacking. This patch brings it up-to-date.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 39230
2014-01-12 12:07:07 +00:00
d823c20f05
lantiq: update default mii modes
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38881
2013-11-20 16:56:58 +00:00
000cefd85e
lantiq: DGN3500 fixups
...
Just fixing up a few things for the Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 38733
2013-11-11 13:15:08 +00:00
5139b2d996
lantiq: rename TDW8970 led adsl->dsl
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38730
2013-11-11 12:19:26 +00:00
dabdc6911a
lantiq: update TDW8970.dts to support buttons properly
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38728
2013-11-11 12:19:18 +00:00
715b62ebad
lantiq: experia v8 fixes
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38328
2013-10-07 15:03:00 +00:00
81fb43d2f1
lantiq: fix fritz3370 dts file
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38327
2013-10-07 15:02:56 +00:00
4f3797386f
lantiq: add support for VGV7519 KPN Experia box v8
...
Signed-off-by: Maikel Bloemendal <mbloemendal@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38266
2013-09-30 20:48:46 +00:00
7665c57a72
lantiq: fix usb on sx76x
...
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 38083
2013-09-20 14:24:30 +00:00
43f1a47430
lantiq: add initial support for Siemens GIGASX76X
...
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38050
2013-09-19 00:50:48 +00:00
3b33adeb99
lantiq: add support for ZyXEL P2601HNFX
...
SVN-Revision: 38049
2013-09-19 00:50:46 +00:00
7d2c5682b9
lantiq: add support for ZTE H201L
...
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38048
2013-09-19 00:50:44 +00:00
John Crispin
Luka Perkov