Note that the Alix6 uses GPIO 27 to disable wireless transmit (W_DIS#), whereas on all other versions this is used to actuate the speaker.
GPIO 1 : SIM select (Alix6)
GPIO 6 : LED1
GPIO 25 : LED2
GPIO 27 : LED3 or RFKILL (Alix6)
GPIO 24 : Soft switch 1
No kernel version bump. Added i2c-scx200-acb for lm-sensors support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 26880
Note that the Alix6 uses GPIO 27 to disable wireless transmit (W_DIS#), whereas on all other versions this is used to actuate the speaker.
GPIO 1 : SIM select (Alix6)
GPIO 6 : LED1
GPIO 25 : LED2
GPIO 27 : LED3 or RFKILL (Alix6)
GPIO 24 : Soft switch 1
No kernel version bump. Added i2c-scx200-acb for lm-sensors support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 26879
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26878
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26876
Make the fixup board ID independent from the image name to allow using
the same board ID for similar devices.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26874
This patch adds 802.1Q VLAN support for the ADM6996M chip.
The driver is loaded for both the FC and M model. It will detect which of the
two chips is connected. The FC model is initialised, but no further
functionality is offered.
The PHY driver will always report "100 Mbit/s, link up", for both the M and FC
models. This reflects the fact that the link between switch chip and Ethernet
MAC is always on[1].
Further documentation can be found in the kernel's
Documentation/networking/adm6996.txt
Signed-of-By: Peter Lebbing <peter@digitalbrains.com>
SVN-Revision: 26865
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.
The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.
SVN-Revision: 26855
If there is no sprom on an ssb based pci device on the brcm47xx
architecture ssb now asks the architecture code to look into the nvram
to get some sprom data for this device. Now we are able to read out
pci/1/1/ foo or pci/1/3/ foo config options.
This will fix some problems where the wireless devices does not got an
mac address and the following message was show:
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
SVN-Revision: 26801
SPIN_LOCK_UNLOCKED has been deprecated since 2.6.19 and will get removed
in 2.6.39, so replace it with DEFINE_SPINLOCK().
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26770
Use offset from struct mtd_part instead of struct mtd_partition for defining
the new partitions. This enables the usage of MTDPART_OFS_APPEND macro in
struct mtd_partition.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
SVN-Revision: 26705
Dual image capable CFEs store an image sequence at the same place as
currently OpenWrt stores the actual rootfs length, so it will get
overwritten when flashing through such a CFE.
To prevent this from happening, move the rootfs length field to the next
four bytes, thus completely using the reserved1 field.
Since the reserved1 field is now completely in use, it does not make sense
to allow it to be set from the imagetag utility, so remove the option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26680
Add the PC speaker back to the Geos platform.
Add DMI support in BIOS.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 26678
These patches were submitted to netdev and will likely be out in 2.6.38.3.
In the meantime, they're needed in 2.6.37.6.
Patch by Philip Prindeville
SVN-Revision: 26616
Add support for the Buffalo WZR-HP-G301NH. The only difference between it
and the WZR-HP-G00NH is that it has a RTL8366RB instead of a RTL8366S.
Since we don't do runtime detection of the switch, we need a separate
machine definition for it.
While we are at it, also rename the profile to reflect that it now is for
more than one device.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26601
Since the PHY driver is only used for the WAN port and there is virtually
no difference between it and the generic PHY driver, we can sefely remove
it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26600
* Some module should be loaded later to load them after the modules they are depending on
* add some more missing config symbols
* make CS5535 build again
SVN-Revision: 26570
Matteo Croce
Hamish Guthrie
Daniel Dickinson
Florian Fainelli
John Crispin
Gabor Juhos
Travis Kemen
Hauke Mehrtens
Alexandros C. Couloumbis
Jo-Philipp Wich
Felix Fietkau