The WAN port should at least respond to IGMP and MLD queries as
otherwise a snooping bridge/switch might drop traffic.
RFC4890 recommends to leave IGMP and MLD unfiltered as they are always
link-scoped anyways.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45613
Before r45593 kmod-l2tp-ip did not depend on kmod-ipv6.
With r45593 support for L2TP IPv6 encapsulation was added and
included in the kmod-l2tp-ip package. This change also
added the dependency to kmod-ipv6 to kmod-l2tp-ip, regardless
of whether the user chose to generally include IPv6 support
or not.
Change this so L2TP over IPv6 and the resulting dependency
to kmod-ipv6 is only included in kmod-l2tp-ip if IPv6 support
is enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45612
OpenVPN assumes that its control channel messages are sent and received
unfragmented, this assumption is broken when CBC record splitting is
enabled in mbedTLS.
The record splitting is intended as countermeasure against BEAST attacks
which do not apply to OpenVPN, therefore we simply disable it until
upstream OpenVPN gains the ability to process fragmented control
messages.
Disabling the splitting also works around a (not remotely triggerable)
segmentation fault in mbedTLS.
References:
* https://dev.openwrt.org/ticket/19101
* https://community.openvpn.net/openvpn/ticket/524
* https://github.com/ARMmbed/mbedtls/pull/185
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45602
This reverts commit ff84c27a281bc19df19bc62ee8688cca5586f6e3.
This tool has really broken size handling (many values hardcoded), it
crashes right now in case of NVRAM not filling whole MTD partition.
Conflicts:
package/utils/nvram/src/nvram.h
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45579
This reverts r43204. The symlinks are faulty, as they point to a
temporary staging dir
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45569
For years Broadcom devices use 64 KiB NVRAM partition size and some of
them indeed have it filled in more than 50%. This change allows handling
whole NVRAM e.g. on Netgear WNDR4500 and Netgear R8000.
The same fix was applied to kernel in upstream commit 6ab7c29.
Reported-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45566
We don't have broadcom-diag for months or years now and the correct
solution is to simply don't have "nvram" partition on WGT634U anyway.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45564
Sytax of /proc/mtd is following:
dev: size erasesize name
which means that sscanf "mtd%d: %08x" reads size, not erasesize.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45563
instead of failing when authsae is not installed, also try using
wpa_supplicant as the newly added -mesh variants support mesh mode
and SAE encryption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45520
The most significant change from the previous version is the trimming of
the 300-ip_tiny.patch to lib/utils.c where a section previously patched
had vanished. That section of the patch was removed.
Built and lightly tested on ar71xx against uClibc and musl.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 45512
Hostapd's control file location was changed in 2013, and that has apparently
broken the wps button hotplug script in cases where there are multiple radios
and wps is possibly configured also for the second radio. The current wps
button hotplug script always handles only the first radio.
https://dev.openwrt.org/browser/trunk/package/network/services/hostapd/files/wps-hotplug.sh
The reason is that the button hotplug script seeks directories like
/var/run/hostapd*, as the hostapd-phy0.conf files were earlier in
per-interface subdirectories.
Currently the *.conf files are directly in /var/run and the control sockets
are in /var/run/hostapd, but there is no subdirectory for each radio.
root@OpenWrt:/# ls /var/run/hostapd*
/var/run/hostapd-phy0.conf /var/run/hostapd-phy1.conf
/var/run/hostapd:
wlan0 wlan1
The hotplug script was attempted to be fixed after the hostapd change by
r38986 in Dec2013, but that change only unbroke the script for the first
radio, but left it broken for multiple radios.
https://dev.openwrt.org/changeset/38986/
The script fails to find subdirectories with [ -d "$dir" ], and passes just
the only found directory /var/run/hostapd, leading into activating only the
first radio, as hostapd_cli defaults to first socket found inthe passed
directory:
root@OpenWrt:/# hostapd_cli -?
...
usage: hostapd_cli [-p<path>] [-i<ifname>] [-hvB] [-a<path>] \
[-G<ping interval>] [command..]
...
-p<path> path to find control sockets (default: /var/run/hostapd)
...
-i<ifname> Interface to listen on (default: first interface found in the
socket path)
Below is a run with the default script and with my proposed solution.
Default script (with logging added):
==================================
root@OpenWrt:/# cat /etc/rc.button/wps
#!/bin/sh
if [ "$ACTION" = "pressed" -a "$BUTTON" = "wps" ]; then
for dir in /var/run/hostapd*; do
[ -d "$dir" ] || continue
logger "WPS activated for: $dir"
hostapd_cli -p "$dir" wps_pbc
done
fi
>>>> WPS BUTTON PRESSED <<<<<
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan0 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan1 wps_get_status
PBC Status: Timed-out
Last WPS result: None
root@OpenWrt:/# logread | grep WPS
Tue Apr 14 18:38:50 2015 user.notice root: WPS activated for: /var/run/hostapd
wlan0 got WPS activated, while wlan1 remained inactive.
I have modified the script to search for sockets instead of directories and
to use the "-i" option with hostapd_cli, and now the script properly
activates wps for both radios. As "-i" needs the interface name instead of
the full path, the script first changes dir to /var/run/hostapd to get simply
the interface names.
Modified script (with logging):
===============================
root@OpenWrt:/# cat /etc/rc.button/wps
#!/bin/sh
if [ "$ACTION" = "pressed" -a "$BUTTON" = "wps" ]; then
cd /var/run/hostapd
for dir in *; do
[ -S "$socket" ] || continue
logger "WPS activated for: $socket"
hostapd_cli -i "$socket" wps_pbc
done
fi
>>>> WPS BUTTON PRESSED <<<<<
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan0 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan1 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# logread | grep WPS
Tue Apr 14 18:53:06 2015 user.notice root: WPS activated for: wlan0
Tue Apr 14 18:53:06 2015 user.notice root: WPS activated for: wlan1
Both radios got their WPS activated properly.
I am not sure if my solution is optimal, but it seems to work. WPS button is
maybe not that often used functionality, but it might be fixed in any case.
Routers with multiple radios are common now, so the bug is maybe more
prominent than earlier.
The modified script has been in a slightly different format in my community
build since r42420 in September 2014.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45492
The last line of procd.sh has a reference to procd_add_interface_reload. procd_add_interface_reload
doesn't seem to exist. I've removed the reference of it to minimize confusion.
Signed-off-by: Eric Schultz <eschultz@prplfoundation.org>
SVN-Revision: 45487
Depending on configuration, disable the LED before writing the trigger
and enable it after writing it. Fixes LEDs where the value defaults to 1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45463
it has been non-functional for years and caused numerous memleaks and
crashes for people that tried to enable it.
it has no maintained upstream source, and it does not look like it's
going to be fixed any time soon
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45423
To prevent future confusion around '/overlay' vs. 'overlay' simply reject
relative path specifications as mount points since such paths result in
undefined behaviour anyway.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45404
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45380
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45379
Fixes build failure caught by buildbot:
IEEE Std 802.15.4 Low-Rate Wireless Personal Area Networks support (IEEE802154) [M/n/y/?] m
6lowpan support over IEEE 802.15.4 (IEEE802154_6LOWPAN) [N/m/?] (NEW) aborted!
Console input/output is redirected. Run 'make oldconfig' to update configuration.
make[6]: *** [silentoldconfig] Error 1
make[5]: *** [silentoldconfig] Error 2
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45357
r45270 removed ieee80211n=%d from the format string but didn't remove
the parameter itself. Though this probably doesn't cause any harm, it's
quite confusing and unneeded.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45351
it causes problems with newer iptables when ipv6 is disabled as iptc uncoditionally links ip6tc
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 45350
This patch adds the wpan-tools (iwpan) utility to OpenWRT
build system. This utility required to manage IEE-802.15.4
devices.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
SVN-Revision: 45349
Current NAND sysupgrade process is a bit hard to follow due to the way
of triggering stage1. Currently this is done by leaving a /mark/ in the
form of /tmp/sysupgrade-nand-path during nand_do_platform_check.
Existence of this mark stops standard sysupgrade process (as the result
of sysupgrade_pre_upgrade exit). This may be a bit misleading.
Proposed solution adds a new function that will allow platform.sh
trigger NAND sysupgrade consciously. This will also allow cleaning
nand_do_platform_check limiting it to just checking the image.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45338
- move config symbol to separate package (Why was it there in the first place?)
- 8723au might be used in some USB sticks or on some sunxi boards
compile tested only
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45336
Enables last error support for the PPP protocol handlers.
In generic teardown the PPP daemon exit code is translated into
a self explaining error string which is set as interface error
by proto_notify_error in case of failure.
Signed-off-by: Johan Peeters <johan.peeters111@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45333
this allow us to use syslog tcp with \0 trailer
instead of \n trailer (logread -0 option)
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 45329
Subtarget legacy is supposed to support all ssb SoC except for BCM4705.
There are few BCM4703 devices with 802.11n supprt (WRT160N v1.0, v1.1).
Few BCM4704 devices with 802.11n: ASUS WL-500W, Linksys WRT150N v1.0 &
v1.1, Linksys WRT300N v1.0, Netgear WNDR3300 v1, WNR834B v1 & v2.
It seems we have to enable N-PHY for legacy as well to support above.
Unfortunately it increases root.squashfs size by 48 460 B.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45309
This driver is upstream since 2012 (commit: a8e510f682f), so switch to
it and remove own sources. Also place it under "Network Devices" menu
together with other phy drivers.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 45269
The arg argument is missing to the printer call in the print_option
utility when the option flag OPT_A2STRVAL is set.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45264
PPPD crashes (SEGV) when the dump or dryrun options are specified and an option
is internally defined as "o_special" with an option flag of "OPT_A2STRVAL".
As the option value is not saved when the parameter is processed, a reference
to the option will result into a crash (e.g. when printing).
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45263
User might have modified/extended template direct or by LuCI application.
So do not overwrite on update/upgrade.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 45258
Most AP devices out there do not have a properly programmed regulatory
domain code, which means they are limited to US frequencies by default.
This has been a major annoyance for a long time now. Since no fix for
the manfuacturing process seems to be forthcoming, the only sane option
seems to be to allow users to change the country code in such cases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45252
Otherwise procd cannot initialize the watchdog since the module will
be loaded later.
Tested with booke_wdt.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 45239
CONFIG_MFD_OMAP_USB_HOST is needed for working USB on BeagleBoard
tested on BeagleBoard C4 (EBVBeagle)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45236
replaces kmod-usb-serial-motorola-phone it's found only in Kernel <3.12
This module handles many simple USB serial devices
like Motorola Phones, GPS reveivers in Kernels above 3.14
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45233
This module is needed for bluetooth audio playback
with pulseaudio 6 and bluez5.
a working guide can be found in the wiki:
http://wiki.openwrt.org/wiki/bluetooth.audio
(additional packages/modifications are required
and submitted to github feeds)
tested with:
Android mobile (Sony Xperia M) as audio source
TI omap BeagleBoard as audio sink
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45231
This patch backports the option --tftp-no-fail to dnsmasq and prevents the
service from aborting if the specified TFTP root directory is not available;
this might be the case if TFTP files are located on external media that might
occasionally not be present at startup.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 45213
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: changes in input.mk broke the patch, some of the CONFIG_SND_*
stuff was added already
SVN-Revision: 45205
from upstream
commit title: "[IPV4]: The scheduled removal of multipath cached routing support."
removed in Kernel 2.6.23 (2007)
Reasons: very buggy, no maintainer, no fixes
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45121
driver in staging since 3.14
removed upstream in 3.17
from upstream commit message:
Most webcams covered by this driver are now supported by gspca.
Nobody has the hardware or is willing to convert the remaining devices to gspca.
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45120
This updates libnetfilter_conntrack to the latest
stable version 1.0.4 which was released Aug-06-2013.
Changeset is available here:
http://git.netfilter.org/libnetfilter_conntrack/log/
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 45074
To enable 802.11r, wpa_key_mgmt should contain FT-EAP or FT-PSK. Allow
multiple key management algorithms to make this possible.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 45050
The 802.11r implementation in hostapd uses nas_identifier as PMK-R0 Key
Holder identifier. As 802.11r can also be used with WPA Personal, nasid
should be appended to the hostapd config for all WPA types.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 45049
'hostapd-common' is needed by all of the variants for wifi to function
correctly (a number of the target profiles simply select 'wpad-mini').
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 45048
These new variants include support for mesh mode and SAE crypto.
They always depend on openssl as EC operations are not provided by
the internal crypto implementation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45047
madwifi was dropped upstream, can't find it anywhere in OpenWrt
either, thus finally burrying madwifi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45045
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44969
Helpful to disable when debugging lldpd crashes (when working on it).
When privilege separation is on, some crashes are stack-traced to
some privilege separation code.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 44967
fix a bug the made uloop_end() not work when called from within a uloop_process
callback handler
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44945
Use xattr to store the filesystem initialization state of the overlay.
As long as the filesystem is not marked as initialized yet (happens in
/etc/init.d/done), all overlay data (except for sysupgrade.tgz) will be
discarded before the system is allowed to boot
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44942
There are some places where there is a redundant declaration of
strlcpy() that prevents building perf otherwise.
Signed-off-by: John Szakmeister <john@szakmeister.net>
SVN-Revision: 44926
from Erik Tews <erik@datenzone.de>
This patch has two effects. First, the quickleave feature/behaviour is
disabled for all groups that are used on more than one interface. The
idea of quickleave is to leave a group fast and later figure out whether
there is still somebody interested in that group. For groups used on
more than one interface, it is already known that there is still
somebody interested in that group.
Second, when a leave is received for a group that is used on more than
one interface, igmpproxy sends queries on all interface to discover
remeining listeners for that group. Previously these queries were only
send on the interface the leave was received on, so that listeners on
the other interfaces were not discovered and the group might be left on
the upstream router incorrectly.
This patch can be improved by sending the queries only on the interface
the leave was received on and adapting the algorithm in
internAgeRoute(...) in rttable.c in a way that only one interface is
actually processed and all other interfaces of the route are silently
assumed to be still active.
Signed-off-by: Erik Tews <erik@datenzone.de>
SVN-Revision: 44859
Certain DHCP servers push a gateway outside of the assigned interface subnet,
to support those situations install a host route towards the gateway.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44789
DNSMASQ has the ability to provide a menu to a pxeboot system, using
the --pxe-prompt and --pxe-service configuration options. The current
init.d script converting the "dhcp" file to "dnsmasq.conf" does not
find these options, but they are supported. This patch thus enables
the options.
Signed-off-by: Derek LaHousse <dlahouss@mtu.edu>
SVN-Revision: 44747
Netcat 1.10 compatibility require server options
1.10 compatibility without server option
produce error "NO OPT l!" and completely not function
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 44746
The --dhcp-boot option of dnsmasq does not require servername and serveraddress
arguments if the builtin tftp server is used.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 44744
The names for the config options were taken from lldpd's
configure.ac file.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 44743
Below you'll find a patch to add ipmark module support to ipset.
Changeset 44671 already bumped ipset to version 6.24, but it's still
compiled without ipmark support. This is a requirement for mwan3 v1.6.
Signed-off-by: Jeroen Louwes <jeroen.louwes@gmail.com>
SVN-Revision: 44742
It's the eglibc packaging with a bit of spit-polishing. And testing. :-)
[blogic: merged glibc and eglibc into 1 and made eglibc a glibc variant]
Signed-off-by: Jeff Waugh <jdub@bethesignal.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44701
Included you'll find a patch to bump ipset to version 6.24. This
version supports the ip,fwmark set, which is needed for mwan3 1.6.
Signed-off-by: Jeroen Louwes <jeroen.louwes@gmail.com>
SVN-Revision: 44671
Based on patch by Bryan Forbes <bryan@reigndropsfall.net>
Also update mt76 to update for API changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44655
buildbot complained about
ifxmips_ptm_adsl.c:1445:70: error: macro "alloc_netdev" requires 4 arguments, but only 3 given
g_net_dev[i] = alloc_netdev(0, g_net_dev_name[i], ether_setup);
^
fix that similar to the change made to ltq_ptm_vdsl.c
compile tested only.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44632
The wwan package holds the hotplug script to set mobile broadband
interfaces (un)available. Add it as a dependency to comgt-ncm,
uqmi and umbim.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44631
Interface should not be set unavailable in all error cases,
returning 1 is enough.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44630
Adds ncm proto to the list of checked protocols, sets interfaces
unavailable on device removal and removes the unnecessary ifup
command.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44629
USB modem data files should be a part of the wwan package, which
actually uses them unlike comgt.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44628
Upstream choose to not rely on configure.ac and recursively expand paths in pkgconfig files at make time,
leading to absolute /usr/include & /usr/lib in there... And we don't want that when cross-compiling...
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44627
Tested myself on ixp4xx and mvebu, and (originally)
by Daniel on i.MX6. Also tested on a MIPS target,
to make sure the change to ASFLAGS does not break things.
Based on a patch submitted by Daniel Drown:
https://lists.openwrt.org/pipermail/openwrt-devel/2014-July/026639.html
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Daniel Drown <dan-openwrt@drown.org>
SVN-Revision: 44618
HAMRADIO enabled in all generic configs, but no one platform directly
use related drivers/protocols. This symbol is only used for kmod-ax25
package modules. Furthermore, half of platforms explicitly disables
this symbol, what silently disables build of modules for kmod-ax25
package.
So disable HAMRADIO by-default in generic config, add it to kmod-ax25
package and remove it from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44613
The initial fix for 3.18 in r44346 wrongly treated the newly added
parameter of alloc_netdev to be another function pointer, causing
ether_config to be skipped during ptm netdev init.
Fix this by partially reverting r44346 and properly setting the newly
added macro parameter.
(Tested on VRX200 board)
A similar change might be needed for ltq-ptm-adsl as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44607
IP VTI (Virtual Tunnel Interface) is used to create a virtual device
for IPsec VPN (similar to OpenVPN).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
SVN-Revision: 44606
In mtd_verify(), the return value of md5sum() has been
interpreted as error if nonzero, while the function
returns number of processed bytes, which caused
mtd_verify() to always fail.
This patch fixes error checking to interpret only
negative values as errors.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
SVN-Revision: 44605
Remove the need for the header file to be exported - we don't need most
of it anyway; all we care about are the offset of the rootfs length and
header crc fields.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44557
Procd enabled init scripts can now specify:
procd_set_param stdout 1
procd_set_param stderr 1
... to relay their respective standard IO streams to the system log.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44547
This is required to properly update syslog idents when switching between
log modes.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44546
Update to git head in order to switch the block, mount_root etc. logging to
the common ulog() api for putting early boot messages into dmesg.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44545
Update to git head in order to switch the kmodloader logging to the common
ulog() api for putting early boot messages into dmesg.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44544
Update to git head in order to switch the procd logging to the common ulog()
api for putting early boot messages into dmesg.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44543
Update to git head in order to introduce the new ulog() logging api which
supports early boot logging to dmesg.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44542
- Support external overlays on non-MTD systems again
- Account for new directory structure of overlayfs partitions (additional upper/ component)
- Support executing block from either overlay or rom
- Support loading fstab from either overlay or rom
- Log extroot failures to dmesg
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44535
This is required during early boot in the extroot setup phase to support
loading kmods from the overlay that depend on kmods on the rom partition.
The subsequent mount_root updates will use the LD_LIBRARY_PATH env
variable to pass kmod directories to kmodloader.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44533
This driver is used on IPQ806x to instanciate & drive the ethernet
interfaces.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44521
In a dual-WAN setup, it's useful to specify an interface over which to
have PPTP.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44507
When passing struct termios to ioctl TCGETS and TCSETS should be
used instead of TCGETA and TCSETA, which are meant for the older
struct termio. Should fix https://dev.openwrt.org/ticket/19012
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44506
This patch adds SDIO support for the brcmfmac driver.
For now only very few boards need it.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44465
Kernel commit 1bb5a356c3ea ("net: reduce USB network driver config
options.") hid the USB network drivers behind the new config symbol
CONFIG_USB_NET_DRIVERS.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
SVN-Revision: 44460
configure tries to guess pagesize by calling getconf, provided by eglibc and compiled for the target, not the host.
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44445
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.
This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).
This is especially useful if an OpenWrt device with two radios is used to
retransmit the same network (one in AP mode for other clients, one as STA for
the uplink); the following configuration prevents the device from associating
with itself, given that the own AP to be avoided is using the bssid
'C0:FF:EE:D0:0D:42':
config wifi-iface
option device 'radio2'
option network 'uplink'
option mode 'sta'
option ssid 'MyNetwork'
option encryption 'none'
list bssid_blacklist 'C0:FF:EE:D0:0D:42/00:FF:FF:FF:FF:FF'
This change consists of the following cherry-picked upstream commits:
b3d6a0a8259002448a29f14855d58fe0a624ab76
b83e455451a875ba233b3b8ac29aff8b62f064f2
79cd993a623e101952b81fa6a29c674cd858504f
(squashed to implement bssid_{white,black}lists)
0047306bc9ab7d46e8cc22ff9a3e876c47626473
(Add os_snprintf_error() helper)
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 44438
- kexec-tools is now distributed with tarballs of .tar.gz and .tar.xz
format; .tar.bz2 are not provided anymore.
- Add CONFIG_KEXEC_LZMA for selecting lzma support.
Patches are updated along to:
- Remove the now unnecessary patch 0004-mips_regdefs.patch.
- Drop 100-reduce_size.patch because the size reduction is marginal.
- Allow zlib and lzma support coexist together. This patch has been
merged into upstream project.
- Fix kexec-tools' configure.ac.
- Fix a few compilation warnings.
Size comparison of stripped binaries of kexec malta target with both
zlib and lzma support enabled.
- Before: 41447
- After: 42583
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44437
The recent rework of the 6in4 endpoint update broke the retry mechanism.
Rework the timeout handling and make the update status more verbose.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44327
Align init behaviour with other distros by starting an OpenVPN instance
for each config file found in /etc/openvpn/. This removes the additional
requirement to "register" the configs with uci and thus simplifies the
setup.
Make sure to respect the disabled state in uci to not suddenly autostart
instances which have been previously set to disabled, also skip configs
which are already started due to uci configuration.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44310
Busybox ash does not implement /dev/stdout, therfore any wget output
is written into a file /dev/stdout instead of onto the standard output.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44301
Instead of hardcoding /bin/bash, use /usr/bin/env bash - this fixes the
build on FreeBSD 10.1.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44283
The mt76 driver might have some problem working with MT7602.
MT7602 should not have VHT capabilities . But the driver not identity properly.
Signed-off-by: wengbj <fl.service@t-firefly.com>
SVN-Revision: 44257
The name variable contains at first the package name,
and after the last group name.
This patch fixes /etc/rc.d symlink creation (at least).
Change name in pkgname, change the other name in ugname
(user group name), and id in ugid (user group id)
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 44253
remove obsolete configuration settings
--disable-thread
--enable-nonblocking
--without-krb4
remove SSPI support
only supported on windows
correct --with/without-ca-path handling
only supported with OpenSSL and PolarSSL
correct LDAP/LDAPS protocol
add dependency libopenldap
added SCP/SFTP protocol
default "No"
depends on libssh2
added IDN support
default "No"
depends on libidn
added SMB protocol (new in 7.40)
default "No"
require 'cryptographic authentication' and either 'GnuTLS' or 'OpenSSL' selected
added Unix sockets support (new in 7.40)
default "No"
added error verbose messages
default "No"
changes to Makefile
Increase PKG_RELEASE
PKG_CONFIG_DEPENDS and CONFIGURE_ARGS
extended for new functionality
use "autoconf_bool" for all --enable/--disable options
restructure for easier reading
changes to Config.in
extended for new functionality
implement dependencies
restructure and grouping for easier reading
build tested on XUbuntu 14.10 x86 for x86 (generic) and ar71xx (WNDR3800)
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 44243
Part of rev 44173 added setting the SM Power Save capability in the hostapd.conf
file if the driver indicated that it was supported. It appears this was
incorrect, because the field in the actual HT Capabilities field in the AP
configuration is really a state indication. Just copying the state from the
capability resulted in the AP indicating that it had SMPS enabled all the time
if it supported SMPS. This effectively just disables all clients from sending
packets to the AP with more than one spatial stream, for no good reason.
So remove this part of the change.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44239
This "patch to the patch" fixes a NULL pointer derefence crash in the new
intermediate software queues. The crash can be reproduced by injecting an
802.11 frame with a BSSID that does not belong to a configured vif. The
wperf tool (https://github.com/anyfi/wperf) may be convenient for doing
this.
Signed-off-by: Johan Almbladh <ja@anyfi.net>
SVN-Revision: 44220
This patch adds support for Realtek r8712 and RTL8188SU/RTL8191SU/RTL8192SU
family of fullmac usb wireless cards. The r8712u staging driver only supports
WEXT but works with no problems in OpenWRT.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 44184
This patch fixes the NCM protocol by adding the missing ifname
to the netifd script and changing one unintended "send" statement to
"print" in runcommand.gcom. It also cleans up logging and makes the
manufacturer names case-insensitive. Furthermore, comgt-ncm should
not depend on the USB-serial-related kernel modules, as the cdc-wdm
control device works without them. There is also no need to depend on
kmod-huawei-cdc-ncm, since other manufacturers (like Sony-Ericsson
and Samsung) which use other kernel modules should also be supported.
I'd appreciate if someone with Samsung or Sony-Ericsson modems could
test this, I was only able to test it with Huawei E3276, E3372 and
E353.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44182
After r43987 TARGET_lantiq_xrx200_P2812HNUFX does not exist anymore.
Fix empty menuconfig bootloader selection by making u-boot depend on
one of the new target profiles.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 44179
* Update to version 7.40.0
* remove non existing config options around enable/disable HTTPS protocoll
* remove --with-ca-path if ssl support disabled
* set proxy support as default like all versions before CC did
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 44176
Update the libertas driver to configure symlinks in sysfs. This enables
the driver to be handled correctly by the mac80211/netifd/hostapd scripts.
With this patch, the wireless interface is functional on Guruplug Server Plus.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44174
Add some missing 802.11n capabilities to the hostapd ht_capab string when
supported by the hardware: Spatial Multiplexing Power-Save and 7935-byte AMSDUs.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44173
If '/sys/class/ieee80211/phyN' is not a symlink, the call to readlink
produces either an empty path (if /sys/class/ieee80211/phyN/device doesn't
exist) or a path that begins with '/sys/class/ieee80211' (which does not
work with the subsequent line to strip '/sys/devices' from the beginning of
the path). Modify the checks to detect these conditions, and fallback to
using the macaddr.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44172
Change the name of the package to match the module name so it matches the
package name referenced by the Kirkwood (Guruplug) profile.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44171
The previous update introducing LFS support unconditionally changed the
sprintf() pattern used to print the file modification time to use PRIx64.
Explicitely convert the st_mtime member of the stat struct to uint64_t in
order to avoid type mismatch errors when building for non-64bit targets.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44138
* Fix the ubus plugin to not make its uhttpd_plugin entry symbol
constant as uhttpd needs to modify its list_head member
* Make sure that uhttpd supports large files by using 64bit ints
where appropriate and by passing _FILE_OFFSET_BITS=64 to the build
* Plug a possible memleak in the directory listing code
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44135
Update to latest git head in order to support disabling the build
of upgraded which causes linker errors on avr32.
This also adds some fixes to the ubus system.info and system.board
methods.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44134
The previous implementation of the "host-uniq" option used plain strings for
passing the value to pppd which made it impossible to specify binary data.
Switch the format to a hex encoded string to support binary data.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44094
Extend the DHCPv4 handler script to store additional information from the
DHCP lease in the per-interface data object.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44092
Adding support 6LoWPAN over Bluetooth Low Energy in kernel 3.18.
Creating new bluetooth_6lowpan group with CONFIG_6LOWPAN and CONFIG_BT_6LOWPAN.
Adding kernel object dependencies for 6LoWPAN over Bluetooth Low Energy.
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44084
This restores normal pre-r43715 200ms blink-period for the System LED we're all accustomed to see while our OpenWrt routers are booting.
Failsafe possibility will now be signalled with a new 100ms blinking, which is easily recognizable from the normal 200ms booting.
So no existing user will be scared by a new 500ms LED pattern, since such a slow pattern could easily be mistaken for something wrong... I was like "ok why my router is collapsing now, is this a bad flash, a kernel panic, or what else" when I've seen it for the first time ;)
Sorry for not having explained myself better in v1 of this patch.
Original:
Preinit, failsafe is possible: 200ms
Preinit, failsafe not possible anymore, booting normally: 200ms
Failsafe entered: 50ms
Now (after preinit_regular has been introduced):
Preinit, failsafe is possible: 200ms
Preinit, failsafe not possible anymore, booting normally: 500ms *here is the "offending" change*
Failsafe entered: 50ms
With my proposed patch:
Preinit, failsafe is possible: 100ms *indicate this condition with a new timing, that prompts the user to press the key if they want to start failsafe*
Preinit, failsafe not possible anymore, booting normally: 200ms *keep this as before*
Failsafe entered: 50ms
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 44056
Some Huawei mobile broadband sticks utilizing the NCM protocol expose
the control channel as a cdc-wdm device node instead of a virtual TTY.
This device node does not support the terminal ioctls. This patch
adds a check whether the provided device is a TTY or not and does not
attempt to use the terminal ioctls if they are not supported.
v2: reduce diffstat by simplifying code a little
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44054
This patch adds a simple check to silence logging of messages about
unrecognized igmp packets which originate from devices in local network.
Without this patch igmpproxy floods openwrt syslog with messages such as:
user.warn igmpproxy[19818]: The source address 192.168.1.175 for group
239.255.250.250, is not in any valid net for upstream VIF.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 44020
The --quiet-dhcp setting increases privacy by omitting DHCP lease logs including MAC addresses.
Signed-off-by: Lars Kruse <devel@sumpfralle.de>
SVN-Revision: 44006
Introduce configuration options to build an "hardened" OpenWRT.
Options to enable Stack-Smashing Protection, FORTIFY_SOURCE and RELRO
have been introduced.
uClibc makefile now automatically detects if SSP support is necessary.
hostapd makefile has been fixed to use "^" as sed separator since
using a comma was problematic when using "-Wl,-z,now" and the like in
TARGET_CFLAGS.
Currently enabling SSP on user space depends on enabling SSP kernel
side, this is due to the fact that TARGET_CFLAGS are used to build
kernel modules (at least). Suggestions on how to avoid this are welcome.
Using "select" instead of "depends on" doesn't seem to work with choice
entries.
Tested with a lantiq (WBMR) router, GCC 4.8, uClibc and a subset of
the available packages.
Needs to be tested with GCC 4.9 and the remaining packages.
PIE not currently included.
Signed-off-by: Alessandro Di Federico <ale+owrt@clearmind.me>
SVN-Revision: 44005
Otherwise libatomic cannot be used in conjunction with external toolchains.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 43998
iproute2 includes "sanitized" linux kernel headers, which work fine for uClibc, however
with musl there is some header conflict, principally some ipv6 structure redefinition. This
patch removes <linux/in6.h> from include/linux/if_bridge.h to solve the problem.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 43992
Add documentation that makes it easier to find the alternative,
recommended, and default handling for buttons in OpenWrt.
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
SVN-Revision: 43989
This patch fixes adding new stations for some specific drivers when
using more than 1 BSS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43951
Felix Fietkau
Steven Barth
Jo-Philipp Wich
Rafał Miłecki
Nicolas Thill
Imre Kaloz
John Crispin
Luka Perkov
Jonas Gorski
Zoltan Herpai