brcm63xx: add VW6339GU support

Completely untested except for booting from network; wan port
only works in 10/HD, lan1 only in 100/FD.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 39678

target/linux/brcm63xx/base-files/etc/uci-defaults/02_network

@@ -102,6 +102,13 @@ NB6)
 	ucidef_add_switch_vlan "switch0" "2" "0 9t"
 	;;
 
+VW6339GU)
+	ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
+	ucidef_add_switch "switch0" "1" "1"
+	ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 8t"
+	ucidef_add_switch_vlan "switch0" "2" "4 8t"
+	;;
+
 *)
 	ucidef_set_interfaces_lan_wan "eth1" "eth0"
 	;;

target/linux/brcm63xx/patches-3.10/559-board_vw6339gu.patch

@@ -0,0 +1,119 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -4538,6 +4538,108 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_vw6339gu = {
++	.name				= "VW6339GU",
++	.expected_cpu_id		= 0x63268,
++
++	.has_uart0			= 1,
++
++	.has_ehci0			= 1,
++	.has_ohci0			= 1,
++	.num_usbh_ports			= 1,
++
++	.has_enetsw			= 1,
++
++	.enetsw = {
++		.used_ports = {
++			[0] = {
++				.used	= 1,
++				.phy_id	= 1,
++				.name	= "LAN2",
++			},
++
++			[1] = {
++				.used	= 1,
++				.phy_id	= 2,
++				.name	= "LAN3",
++			},
++
++			[2] = {
++				.used	= 1,
++				.phy_id	= 3,
++				.name	= "LAN4",
++			},
++
++			[3] = {
++				.used	= 1,
++				.phy_id	= 4,
++				.name	= "LAN1",
++			},
++
++			[4] = {
++				.used	= 1,
++				.phy_id	= 7,
++				.name	= "WAN",
++			},
++		},
++	},
++
++	.leds = {
++		{
++			.name		= "VW6339GU:green:power",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++		{
++			.name		= "VW6339GU:red:power",
++			.gpio		= 0,
++			.active_low	= 1,
++		},
++		{
++			.name		= "VW6339GU:green:internet",
++			.gpio		= 8,
++			.active_low	= 1,
++		},
++		{
++			.name		= "VW6339GU:red:internet",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "VW6339GU:green:dsl",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{
++			.name		= "VW6339GU:green:wps",
++			.gpio		= 7,
++			.active_low	= 1,
++		},
++		{
++			.name		= "VW6339GU:green:usb",
++			.gpio		= 15,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 32,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -4628,6 +4730,7 @@ static const struct board_info __initcon
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_63268
+ 	&board_963269bhr,
++	&board_vw6339gu,
+ #endif
+ };
+ 

target/linux/brcm63xx/patches-3.10/801-ssb_export_fallback_sprom.patch

@@ -8,7 +8,7 @@
  #include <linux/spi/spi.h>
  #include <linux/spi/spi_gpio.h>
  #include <linux/spi/74x164.h>
-@@ -4636,7 +4637,7 @@ static const struct board_info __initcon
+@@ -4739,7 +4740,7 @@ static const struct board_info __initcon
   * bcm4318 WLAN work
   */
  #ifdef CONFIG_SSB_PCIHOST
@@ -17,7 +17,7 @@
  	.revision		= 0x02,
  	.board_rev		= 0x17,
  	.country_code		= 0x0,
-@@ -4656,6 +4657,7 @@ static struct ssb_sprom bcm63xx_sprom =
+@@ -4759,6 +4760,7 @@ static struct ssb_sprom bcm63xx_sprom =
  	.boardflags_lo		= 0x2848,
  	.boardflags_hi		= 0x0000,
  };