mirror of https://github.com/hak5/openwrt-owl.git
Gabor Juhos
parent
9b7ea0451a
commit
aaac1064de
|
|
@ -0,0 +1,117 @@
|
|||
Index: linux-2.6.25/arch/mips/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/arch/mips/Kconfig
|
||||
+++ linux-2.6.25/arch/mips/Kconfig
|
||||
@@ -18,6 +18,20 @@ choice
|
||||
prompt "System type"
|
||||
default SGI_IP22
|
||||
|
||||
+config MIPS_ADM5120
|
||||
+ bool "ADM5120 SoC based machines"
|
||||
+ select CEVT_R4K
|
||||
+ select CSRC_R4K
|
||||
+ select SYS_HAS_CPU_MIPS32_R1
|
||||
+ select SYS_HAS_EARLY_PRINTK
|
||||
+ select DMA_NONCOHERENT
|
||||
+ select HW_HAS_PCI
|
||||
+ select IRQ_CPU
|
||||
+ select SYS_SUPPORTS_LITTLE_ENDIAN
|
||||
+ select SYS_SUPPORTS_BIG_ENDIAN
|
||||
+ select SYS_SUPPORTS_32BIT_KERNEL
|
||||
+ select GENERIC_GPIO
|
||||
+
|
||||
config MACH_ALCHEMY
|
||||
bool "Alchemy processor based machines"
|
||||
|
||||
@@ -683,6 +697,7 @@ config WR_PPMC
|
||||
|
||||
endchoice
|
||||
|
||||
+source "arch/mips/adm5120/Kconfig"
|
||||
source "arch/mips/au1000/Kconfig"
|
||||
source "arch/mips/basler/excite/Kconfig"
|
||||
source "arch/mips/jazz/Kconfig"
|
||||
Index: linux-2.6.25/arch/mips/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/arch/mips/Makefile
|
||||
+++ linux-2.6.25/arch/mips/Makefile
|
||||
@@ -174,6 +174,16 @@ cflags-$(CONFIG_MACH_JAZZ) += -Iinclude/
|
||||
load-$(CONFIG_MACH_JAZZ) += 0xffffffff80080000
|
||||
|
||||
#
|
||||
+# ADMtek 5120
|
||||
+#
|
||||
+
|
||||
+libs-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/prom/
|
||||
+core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/
|
||||
+core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/boards/
|
||||
+cflags-$(CONFIG_MIPS_ADM5120) += -Iinclude/asm-mips/mach-adm5120
|
||||
+load-$(CONFIG_MIPS_ADM5120) += 0xffffffff80001000
|
||||
+
|
||||
+#
|
||||
# Common Alchemy Au1x00 stuff
|
||||
#
|
||||
core-$(CONFIG_SOC_AU1X00) += arch/mips/au1000/common/
|
||||
Index: linux-2.6.25/include/asm-mips/bootinfo.h
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/include/asm-mips/bootinfo.h
|
||||
+++ linux-2.6.25/include/asm-mips/bootinfo.h
|
||||
@@ -94,6 +94,58 @@
|
||||
#define MACH_MSP7120_FPGA 5 /* PMC-Sierra MSP7120 Emulation */
|
||||
#define MACH_MSP_OTHER 255 /* PMC-Sierra unknown board type */
|
||||
|
||||
+/*
|
||||
+ * Valid machtype for group ADMtek ADM5120
|
||||
+ */
|
||||
+#define MACH_ADM5120_GENERIC 0 /* Generic board */
|
||||
+#define MACH_ADM5120_WP54G_WRT 1 /* Compex WP54G-WRT */
|
||||
+#define MACH_ADM5120_WP54G 2 /* Compex WP54G */
|
||||
+#define MACH_ADM5120_WP54AG 3 /* Compex WP54AG */
|
||||
+#define MACH_ADM5120_WPP54G 4 /* Compex WPP54G */
|
||||
+#define MACH_ADM5120_WPP54AG 5 /* Compex WPP54AG */
|
||||
+#define MACH_ADM5120_NP28G 6 /* Compex NP28G */
|
||||
+#define MACH_ADM5120_NP28GHS 7 /* Compex NP28G HotSpot */
|
||||
+#define MACH_ADM5120_NP27G 8 /* Compex NP27G */
|
||||
+#define MACH_ADM5120_WP54Gv1C 9 /* Compex WP54G version 1C */
|
||||
+#define MACH_ADM5120_RB_111 10 /* Mikrotik RouterBOARD 111 */
|
||||
+#define MACH_ADM5120_RB_112 11 /* Mikrotik RouterBOARD 112 */
|
||||
+#define MACH_ADM5120_RB_133 12 /* Mikrotik RouterBOARD 133 */
|
||||
+#define MACH_ADM5120_RB_133C 13 /* Mikrotik RouterBOARD 133c */
|
||||
+#define MACH_ADM5120_RB_150 14 /* Mikrotik RouterBOARD 150 */
|
||||
+#define MACH_ADM5120_RB_153 15 /* Mikrotik RouterBOARD 153 */
|
||||
+#define MACH_ADM5120_HS100 16 /* ZyXEL HomeSafe 100/100W */
|
||||
+#define MACH_ADM5120_P334 17 /* ZyXEL Prestige 334 */
|
||||
+#define MACH_ADM5120_P334U 18 /* ZyXEL Prestige 334U */
|
||||
+#define MACH_ADM5120_P334W 19 /* ZyXEL Prestige 334W */
|
||||
+#define MACH_ADM5120_P334WH 20 /* ZyXEL Prestige 334WH */
|
||||
+#define MACH_ADM5120_P334WHD 21 /* ZyXEL Prestige 334WHD */
|
||||
+#define MACH_ADM5120_P334WT 22 /* ZyXEL Prestige 334WT */
|
||||
+#define MACH_ADM5120_P335 23 /* ZyXEL Prestige 335/335WT */
|
||||
+#define MACH_ADM5120_P335PLUS 24 /* ZyXEL Prestige 335Plus */
|
||||
+#define MACH_ADM5120_P335U 25 /* ZyXEL Prestige 335U */
|
||||
+#define MACH_ADM5120_ES2108 26 /* ZyXEL Ethernet Switch 2108 */
|
||||
+#define MACH_ADM5120_ES2108F 27 /* ZyXEL Ethernet Switch 2108-F */
|
||||
+#define MACH_ADM5120_ES2108G 28 /* ZyXEL Ethernet Switch 2108-G */
|
||||
+#define MACH_ADM5120_ES2108LC 29 /* ZyXEL Ethernet Switch 2108-LC */
|
||||
+#define MACH_ADM5120_ES2108PWR 30 /* ZyXEL Ethernet Switch 2108-PWR */
|
||||
+#define MACH_ADM5120_ES2024A 31 /* ZyXEL Ethernet Switch 2024A */
|
||||
+#define MACH_ADM5120_ES2024PWR 32 /* ZyXEL Ethernet Switch 2024PWR */
|
||||
+#define MACH_ADM5120_CAS630 33 /* Cellvision CAS-630/630W */
|
||||
+#define MACH_ADM5120_CAS670 34 /* Cellvision CAS-670/670W */
|
||||
+#define MACH_ADM5120_CAS700 36 /* Cellvision CAS-700/700W */
|
||||
+#define MACH_ADM5120_CAS771 37 /* Cellvision CAS-771/771W */
|
||||
+#define MACH_ADM5120_CAS790 38 /* Cellvision CAS-790 */
|
||||
+#define MACH_ADM5120_CAS861 39 /* Cellvision CAS-861/861W */
|
||||
+#define MACH_ADM5120_NFS101U 40 /* Cellvision NFS-101U/101WU */
|
||||
+#define MACH_ADM5120_NFS202U 41 /* Cellvision NFS-202U/202WU */
|
||||
+#define MACH_ADM5120_EASY5120PATA 42 /* Infineon EASY 5120P-ATA */
|
||||
+#define MACH_ADM5120_EASY5120RT 43 /* Infineon EASY 5120-RT */
|
||||
+#define MACH_ADM5120_EASY5120WVOIP 44 /* Infineon EASY 5120-WVoIP */
|
||||
+#define MACH_ADM5120_EASY83000 45 /* Infineon EASY-83000 */
|
||||
+#define MACH_ADM5120_BR6104K 46 /* Edimax BR-6104K/BR-6104KP */
|
||||
+#define MACH_ADM5120_RB_192 47 /* Mikrotik RouterBOARD 192 */
|
||||
+#define MACH_ADM5120_BR61x4WG 48 /* Edimax BR-6104Wg/BR-6114WG */
|
||||
+
|
||||
#define CL_SIZE COMMAND_LINE_SIZE
|
||||
|
||||
extern char *system_type;
|
||||
|
|
@ -0,0 +1,26 @@
|
|||
Index: linux-2.6.25/drivers/mtd/maps/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/mtd/maps/Kconfig
|
||||
+++ linux-2.6.25/drivers/mtd/maps/Kconfig
|
||||
@@ -590,5 +590,9 @@ config MTD_PLATRAM
|
||||
|
||||
This selection automatically selects the map_ram driver.
|
||||
|
||||
+config MTD_ADM5120
|
||||
+ tristate "Map driver for ADM5120 based boards"
|
||||
+ depends on MIPS_ADM5120
|
||||
+
|
||||
endmenu
|
||||
|
||||
Index: linux-2.6.25/drivers/mtd/maps/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/mtd/maps/Makefile
|
||||
+++ linux-2.6.25/drivers/mtd/maps/Makefile
|
||||
@@ -44,6 +44,7 @@ obj-$(CONFIG_MTD_DBOX2) += dbox2-flash.
|
||||
obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
|
||||
obj-$(CONFIG_MTD_PCI) += pci.o
|
||||
obj-$(CONFIG_MTD_ALCHEMY) += alchemy-flash.o
|
||||
+obj-$(CONFIG_MTD_ADM5120) += adm5120-flash.o
|
||||
obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o
|
||||
obj-$(CONFIG_MTD_EDB7312) += edb7312.o
|
||||
obj-$(CONFIG_MTD_IMPA7) += impa7.o
|
||||
|
|
@ -0,0 +1,27 @@
|
|||
Index: linux-2.6.25/drivers/net/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/net/Kconfig
|
||||
+++ linux-2.6.25/drivers/net/Kconfig
|
||||
@@ -606,6 +606,10 @@ config MIPS_AU1X00_ENET
|
||||
If you have an Alchemy Semi AU1X00 based system
|
||||
say Y. Otherwise, say N.
|
||||
|
||||
+config MIPS_ADM5120_ENET
|
||||
+ tristate "MIPS ADM5120 Ethernet switch support"
|
||||
+ depends on MIPS_ADM5120
|
||||
+
|
||||
config SGI_IOC3_ETH
|
||||
bool "SGI IOC3 Ethernet"
|
||||
depends on PCI && SGI_IP27
|
||||
Index: linux-2.6.25/drivers/net/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/net/Makefile
|
||||
+++ linux-2.6.25/drivers/net/Makefile
|
||||
@@ -187,6 +187,7 @@ obj-$(CONFIG_SC92031) += sc92031.o
|
||||
# This is also a 82596 and should probably be merged
|
||||
obj-$(CONFIG_LP486E) += lp486e.o
|
||||
|
||||
+obj-$(CONFIG_MIPS_ADM5120_ENET) += adm5120sw.o
|
||||
obj-$(CONFIG_ETH16I) += eth16i.o
|
||||
obj-$(CONFIG_ZORRO8390) += zorro8390.o
|
||||
obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
|
||||
|
|
@ -0,0 +1,35 @@
|
|||
Index: linux-2.6.25/drivers/usb/host/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/usb/host/Kconfig
|
||||
+++ linux-2.6.25/drivers/usb/host/Kconfig
|
||||
@@ -260,3 +260,6 @@ config USB_R8A66597_HCD
|
||||
To compile this driver as a module, choose M here: the
|
||||
module will be called r8a66597-hcd.
|
||||
|
||||
+config USB_ADM5120_HCD
|
||||
+ tristate "ADM5120 HCD support (EXPERIMENTAL)"
|
||||
+ depends on USB && MIPS_ADM5120 && EXPERIMENTAL
|
||||
Index: linux-2.6.25/drivers/usb/host/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/usb/host/Makefile
|
||||
+++ linux-2.6.25/drivers/usb/host/Makefile
|
||||
@@ -8,6 +8,7 @@ endif
|
||||
|
||||
obj-$(CONFIG_PCI) += pci-quirks.o
|
||||
|
||||
+obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o
|
||||
obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
|
||||
obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
|
||||
obj-$(CONFIG_USB_OHCI_HCD) += ohci-hcd.o
|
||||
Index: linux-2.6.25/drivers/usb/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/usb/Makefile
|
||||
+++ linux-2.6.25/drivers/usb/Makefile
|
||||
@@ -16,6 +16,7 @@ obj-$(CONFIG_USB_UHCI_HCD) += host/
|
||||
obj-$(CONFIG_USB_SL811_HCD) += host/
|
||||
obj-$(CONFIG_USB_U132_HCD) += host/
|
||||
obj-$(CONFIG_USB_R8A66597_HCD) += host/
|
||||
+obj-$(CONFIG_USB_ADM5120_HCD) += host/
|
||||
|
||||
obj-$(CONFIG_USB_ACM) += class/
|
||||
obj-$(CONFIG_USB_PRINTER) += class/
|
||||
|
|
@ -0,0 +1,38 @@
|
|||
Index: linux-2.6.25/drivers/leds/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/leds/Kconfig
|
||||
+++ linux-2.6.25/drivers/leds/Kconfig
|
||||
@@ -25,6 +25,21 @@ config LEDS_ATMEL_PWM
|
||||
This option enables support for LEDs driven using outputs
|
||||
of the dedicated PWM controller found on newer Atmel SOCs.
|
||||
|
||||
+config LEDS_ADM5120
|
||||
+ tristate "LED Support for ADM5120 GPIO LEDs"
|
||||
+ depends on LEDS_GPIO && MIPS_ADM5120
|
||||
+ help
|
||||
+ This option enables support for LEDs connected to GPIO lines
|
||||
+ on ADM5120 SoC based platforms.
|
||||
+
|
||||
+config LEDS_ADM5120_EXPERIMENTAL
|
||||
+ bool "Enable ADM5120 LEDs experimental code"
|
||||
+ depends on LEDS_ADM5120
|
||||
+
|
||||
+config LEDS_ADM5120_DIAG
|
||||
+ bool "Enable ADM5120 LEDs diagnostic mode"
|
||||
+ depends on LEDS_ADM5120
|
||||
+
|
||||
config LEDS_CORGI
|
||||
tristate "LED Support for the Sharp SL-C7x0 series"
|
||||
depends on LEDS_CLASS && PXA_SHARP_C7xx
|
||||
Index: linux-2.6.25/drivers/leds/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/leds/Makefile
|
||||
+++ linux-2.6.25/drivers/leds/Makefile
|
||||
@@ -5,6 +5,7 @@ obj-$(CONFIG_LEDS_CLASS) += led-class.o
|
||||
obj-$(CONFIG_LEDS_TRIGGERS) += led-triggers.o
|
||||
|
||||
# LED Platform Drivers
|
||||
+obj-$(CONFIG_LEDS_ADM5120) += leds-adm5120.o
|
||||
obj-$(CONFIG_LEDS_ATMEL_PWM) += leds-atmel-pwm.o
|
||||
obj-$(CONFIG_LEDS_CORGI) += leds-corgi.o
|
||||
obj-$(CONFIG_LEDS_LOCOMO) += leds-locomo.o
|
||||
|
|
@ -0,0 +1,23 @@
|
|||
Index: linux-2.6.25/arch/mips/pci/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/arch/mips/pci/Makefile
|
||||
+++ linux-2.6.25/arch/mips/pci/Makefile
|
||||
@@ -48,3 +48,4 @@ obj-$(CONFIG_TOSHIBA_RBTX4938) += fixup-
|
||||
obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc30x.o
|
||||
obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o
|
||||
obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o
|
||||
+obj-$(CONFIG_PCI_ADM5120) += pci-adm5120.o
|
||||
Index: linux-2.6.25/include/linux/pci_ids.h
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/include/linux/pci_ids.h
|
||||
+++ linux-2.6.25/include/linux/pci_ids.h
|
||||
@@ -1704,6 +1704,9 @@
|
||||
#define PCI_VENDOR_ID_ESDGMBH 0x12fe
|
||||
#define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
|
||||
|
||||
+#define PCI_VENDOR_ID_ADMTEK 0x1317
|
||||
+#define PCI_DEVICE_ID_ADMTEK_ADM5120 0x5120
|
||||
+
|
||||
#define PCI_VENDOR_ID_SIIG 0x131f
|
||||
#define PCI_SUBVENDOR_ID_SIIG 0x131f
|
||||
#define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000
|
||||
|
|
@ -0,0 +1,26 @@
|
|||
Index: linux-2.6.25/drivers/leds/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/leds/Kconfig
|
||||
+++ linux-2.6.25/drivers/leds/Kconfig
|
||||
@@ -213,4 +213,12 @@ config LEDS_TRIGGER_DEFAULT_ON
|
||||
This allows LEDs to be initialised in the ON state.
|
||||
If unsure, say Y.
|
||||
|
||||
+config LEDS_TRIGGER_ADM5120_SWITCH
|
||||
+ tristate "LED ADM5120 Switch Port Status Trigger"
|
||||
+ depends on LEDS_TRIGGERS && LEDS_ADM5120
|
||||
+ help
|
||||
+ This allows LEDs to be controlled by the port states of
|
||||
+ the ADM5120 built-in Ethernet Switch
|
||||
+ If unsure, say N.
|
||||
+
|
||||
endif # NEW_LEDS
|
||||
Index: linux-2.6.25/drivers/leds/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/leds/Makefile
|
||||
+++ linux-2.6.25/drivers/leds/Makefile
|
||||
@@ -30,3 +30,4 @@ obj-$(CONFIG_LEDS_TRIGGER_IDE_DISK) += l
|
||||
obj-$(CONFIG_LEDS_TRIGGER_HEARTBEAT) += ledtrig-heartbeat.o
|
||||
obj-$(CONFIG_LEDS_TRIGGER_MORSE) += ledtrig-morse.o
|
||||
obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON) += ledtrig-default-on.o
|
||||
+obj-$(CONFIG_LEDS_TRIGGER_ADM5120_SWITCH) += ledtrig-adm5120-switch.o
|
||||
|
|
@ -0,0 +1,39 @@
|
|||
Index: linux-2.6.25/drivers/mtd/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/mtd/Kconfig
|
||||
+++ linux-2.6.25/drivers/mtd/Kconfig
|
||||
@@ -168,6 +168,22 @@ config MTD_OF_PARTS
|
||||
the partition map from the children of the flash node,
|
||||
as described in Documentation/powerpc/booting-without-of.txt.
|
||||
|
||||
+config MTD_MYLOADER_PARTS
|
||||
+ tristate "MyLoader partition parsing"
|
||||
+ depends on MIPS_ADM5120 && MTD_PARTITIONS
|
||||
+ ---help---
|
||||
+ MyLoader is a bootloader which allows the user to define partitions
|
||||
+ in flash devices, by putting a table in the second erase block
|
||||
+ on the device, similar to a partition table. This table gives the
|
||||
+ offsets and lengths of the user defined partitions.
|
||||
+
|
||||
+ If you need code which can detect and parse these tables, and
|
||||
+ register MTD 'partitions' corresponding to each image detected,
|
||||
+ enable this option.
|
||||
+
|
||||
+ You will still need the parsing functions to be called by the driver
|
||||
+ for your particular device. It won't happen automatically.
|
||||
+
|
||||
comment "User Modules And Translation Layers"
|
||||
|
||||
config MTD_CHAR
|
||||
Index: linux-2.6.25/drivers/mtd/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/mtd/Makefile
|
||||
+++ linux-2.6.25/drivers/mtd/Makefile
|
||||
@@ -12,6 +12,7 @@ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redbo
|
||||
obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
|
||||
obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
|
||||
obj-$(CONFIG_MTD_OF_PARTS) += ofpart.o
|
||||
+obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
|
||||
|
||||
# 'Users' - code which presents functionality to userspace.
|
||||
obj-$(CONFIG_MTD_CHAR) += mtdchar.o
|
||||
|
|
@ -0,0 +1,95 @@
|
|||
Index: linux-2.6.25/drivers/mtd/chips/cfi_cmdset_0002.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/mtd/chips/cfi_cmdset_0002.c
|
||||
+++ linux-2.6.25/drivers/mtd/chips/cfi_cmdset_0002.c
|
||||
@@ -47,12 +47,19 @@
|
||||
#define MANUFACTURER_AMD 0x0001
|
||||
#define MANUFACTURER_ATMEL 0x001F
|
||||
#define MANUFACTURER_SST 0x00BF
|
||||
+#define MANUFACTURER_MACRONIX 0x00C2
|
||||
#define SST49LF004B 0x0060
|
||||
#define SST49LF040B 0x0050
|
||||
#define SST49LF008A 0x005a
|
||||
#define AT49BV6416 0x00d6
|
||||
#define MANUFACTURER_SAMSUNG 0x00ec
|
||||
|
||||
+/* Macronix */
|
||||
+#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */
|
||||
+#define MX29LV160T 0x22C4 /* MX29LV160 Top-boot chip */
|
||||
+#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */
|
||||
+#define MX29LV320T 0x22A7 /* MX29LV320 Top-boot chip */
|
||||
+
|
||||
static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
|
||||
static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
|
||||
static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
|
||||
@@ -221,6 +228,41 @@ static void fixup_use_atmel_lock(struct
|
||||
mtd->flags |= MTD_POWERUP_LOCK;
|
||||
}
|
||||
|
||||
+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
|
||||
+/*
|
||||
+ * Some Macronix chips has no/bad bootblock information in the CFI table
|
||||
+ */
|
||||
+static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
|
||||
+{
|
||||
+ struct map_info *map = mtd->priv;
|
||||
+ struct cfi_private *cfi = map->fldrv_priv;
|
||||
+ struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
|
||||
+ __u8 t;
|
||||
+
|
||||
+ switch (cfi->id) {
|
||||
+ /* TODO: put affected chip ids here */
|
||||
+ case MX29LV160B:
|
||||
+ case MX29LV320B:
|
||||
+ t = 2; /* Bottom boot */
|
||||
+ break;
|
||||
+ case MX29LV160T:
|
||||
+ case MX29LV320T:
|
||||
+ t = 3; /* Top boot */
|
||||
+ break;
|
||||
+ default:
|
||||
+ return;
|
||||
+ }
|
||||
+
|
||||
+ if (extp->TopBottom == t)
|
||||
+ /* boot location detected by the CFI layer is correct */
|
||||
+ return;
|
||||
+
|
||||
+ extp->TopBottom = t;
|
||||
+ printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
|
||||
+ "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
|
||||
+}
|
||||
+#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
|
||||
+
|
||||
static struct cfi_fixup cfi_fixup_table[] = {
|
||||
{ CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL },
|
||||
#ifdef AMD_BOOTLOC_BUG
|
||||
@@ -252,6 +294,9 @@ static struct cfi_fixup fixup_table[] =
|
||||
*/
|
||||
{ CFI_MFR_ANY, CFI_ID_ANY, fixup_use_erase_chip, NULL },
|
||||
{ CFI_MFR_ATMEL, AT49BV6416, fixup_use_atmel_lock, NULL },
|
||||
+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
|
||||
+ { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
|
||||
+#endif
|
||||
{ 0, 0, NULL, NULL }
|
||||
};
|
||||
|
||||
Index: linux-2.6.25/drivers/mtd/chips/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/mtd/chips/Kconfig
|
||||
+++ linux-2.6.25/drivers/mtd/chips/Kconfig
|
||||
@@ -196,6 +196,14 @@ config MTD_CFI_AMDSTD
|
||||
provides support for one of those command sets, used on chips
|
||||
including the AMD Am29LV320.
|
||||
|
||||
+config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
|
||||
+ bool "Fix boot-block location for Macronix flash chips"
|
||||
+ depends on MTD_CFI_AMDSTD
|
||||
+ help
|
||||
+ Some Macronix flash chips have no/wrong boot-block location in the
|
||||
+ CFI table, and the driver may detect the type incorrectly. Select
|
||||
+ this if your board has such chip.
|
||||
+
|
||||
config MTD_CFI_STAA
|
||||
tristate "Support for ST (Advanced Architecture) flash chips"
|
||||
depends on MTD_GEN_PROBE
|
||||
|
|
@ -0,0 +1,74 @@
|
|||
Index: linux-2.6.25/drivers/mtd/chips/jedec_probe.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/mtd/chips/jedec_probe.c
|
||||
+++ linux-2.6.25/drivers/mtd/chips/jedec_probe.c
|
||||
@@ -121,6 +121,10 @@
|
||||
#define UPD29F064115 0x221C
|
||||
|
||||
/* PMC */
|
||||
+#define PM39LV512 0x001B
|
||||
+#define PM39LV010 0x001C
|
||||
+#define PM39LV020 0x003D
|
||||
+#define PM39LV040 0x003E
|
||||
#define PM49FL002 0x006D
|
||||
#define PM49FL004 0x006E
|
||||
#define PM49FL008 0x006A
|
||||
@@ -1170,6 +1174,58 @@ static const struct amd_flash_info jedec
|
||||
ERASEINFO(0x02000,2),
|
||||
ERASEINFO(0x04000,1),
|
||||
}
|
||||
+ }, {
|
||||
+ .mfr_id = MANUFACTURER_PMC,
|
||||
+ .dev_id = PM39LV512,
|
||||
+ .name = "PMC Pm39LV512",
|
||||
+ .uaddr = {
|
||||
+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
|
||||
+ },
|
||||
+ .DevSize = SIZE_64KiB,
|
||||
+ .CmdSet = P_ID_AMD_STD,
|
||||
+ .NumEraseRegions= 1,
|
||||
+ .regions = {
|
||||
+ ERASEINFO(0x01000,16),
|
||||
+ }
|
||||
+ }, {
|
||||
+ .mfr_id = MANUFACTURER_PMC,
|
||||
+ .dev_id = PM39LV010,
|
||||
+ .name = "PMC Pm39LV010",
|
||||
+ .uaddr = {
|
||||
+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
|
||||
+ },
|
||||
+ .DevSize = SIZE_128KiB,
|
||||
+ .CmdSet = P_ID_AMD_STD,
|
||||
+ .NumEraseRegions= 1,
|
||||
+ .regions = {
|
||||
+ ERASEINFO(0x01000,32),
|
||||
+ }
|
||||
+ }, {
|
||||
+ .mfr_id = MANUFACTURER_PMC,
|
||||
+ .dev_id = PM39LV020,
|
||||
+ .name = "PMC Pm39LV020",
|
||||
+ .uaddr = {
|
||||
+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
|
||||
+ },
|
||||
+ .DevSize = SIZE_256KiB,
|
||||
+ .CmdSet = P_ID_AMD_STD,
|
||||
+ .NumEraseRegions= 1,
|
||||
+ .regions = {
|
||||
+ ERASEINFO(0x01000,64),
|
||||
+ }
|
||||
+ }, {
|
||||
+ .mfr_id = MANUFACTURER_PMC,
|
||||
+ .dev_id = PM39LV040,
|
||||
+ .name = "PMC Pm39LV040",
|
||||
+ .uaddr = {
|
||||
+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
|
||||
+ },
|
||||
+ .DevSize = SIZE_512KiB,
|
||||
+ .CmdSet = P_ID_AMD_STD,
|
||||
+ .NumEraseRegions= 1,
|
||||
+ .regions = {
|
||||
+ ERASEINFO(0x01000,128),
|
||||
+ }
|
||||
}, {
|
||||
.mfr_id = MANUFACTURER_PMC,
|
||||
.dev_id = PM49FL002,
|
||||
|
|
@ -0,0 +1,28 @@
|
|||
Index: linux-2.6.25/drivers/mtd/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/mtd/Kconfig
|
||||
+++ linux-2.6.25/drivers/mtd/Kconfig
|
||||
@@ -57,6 +57,11 @@ config MTD_ROOTFS_SPLIT
|
||||
depends on MTD_PARTITIONS
|
||||
default y
|
||||
|
||||
+config MTD_TRXSPLIT
|
||||
+ bool "Automatically find and split TRX partitions"
|
||||
+ depends on MTD_PARTITIONS
|
||||
+ default n
|
||||
+
|
||||
config MTD_REDBOOT_PARTS
|
||||
tristate "RedBoot partition table parsing"
|
||||
depends on MTD_PARTITIONS
|
||||
Index: linux-2.6.25/drivers/mtd/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/mtd/Makefile
|
||||
+++ linux-2.6.25/drivers/mtd/Makefile
|
||||
@@ -8,6 +8,7 @@ mtd-y := mtdcore.o mtdsuper.o
|
||||
mtd-$(CONFIG_MTD_PARTITIONS) += mtdpart.o
|
||||
|
||||
obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o
|
||||
+obj-$(CONFIG_MTD_TRXSPLIT) += trxsplit.o
|
||||
obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
|
||||
obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
|
||||
obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
|
||||
|
|
@ -0,0 +1,30 @@
|
|||
Index: linux-2.6.25/drivers/ata/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/ata/Makefile
|
||||
+++ linux-2.6.25/drivers/ata/Makefile
|
||||
@@ -71,6 +71,7 @@ obj-$(CONFIG_PATA_BF54X) += pata_bf54x.o
|
||||
obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o
|
||||
obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o
|
||||
obj-$(CONFIG_PATA_ICSIDE) += pata_icside.o
|
||||
+obj-$(CONFIG_PATA_RB153_CF) += pata_rb153_cf.o
|
||||
# Should be last but two libata driver
|
||||
obj-$(CONFIG_PATA_ACPI) += pata_acpi.o
|
||||
# Should be last but one libata driver
|
||||
Index: linux-2.6.25/drivers/ata/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/ata/Kconfig
|
||||
+++ linux-2.6.25/drivers/ata/Kconfig
|
||||
@@ -679,4 +679,13 @@ config PATA_BF54X
|
||||
|
||||
If unsure, say N.
|
||||
|
||||
+config PATA_RB153_CF
|
||||
+ tristate "RouterBOARD 153 Compact Flash support"
|
||||
+ depends on MIPS_ADM5120
|
||||
+ help
|
||||
+ This option enables support for a Compact Flash connected on
|
||||
+ the RouterBOARD 153.
|
||||
+
|
||||
+ If unsure, say N.
|
||||
+
|
||||
endif # ATA
|
||||
|
|
@ -0,0 +1,17 @@
|
|||
Index: linux-2.6.25/arch/mips/kernel/head.S
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/arch/mips/kernel/head.S
|
||||
+++ linux-2.6.25/arch/mips/kernel/head.S
|
||||
@@ -126,7 +126,12 @@
|
||||
/*
|
||||
* Reserved space for exception handlers.
|
||||
* Necessary for machines which link their kernels at KSEG0.
|
||||
+ * Use as temporary storage for the kernel command line, so that it
|
||||
+ * can be updated easily without having to relink the kernel.
|
||||
*/
|
||||
+
|
||||
+EXPORT(_image_cmdline)
|
||||
+ .ascii "CMDLINE:"
|
||||
.fill 0x400
|
||||
#endif
|
||||
|
||||
|
|
@ -0,0 +1,297 @@
|
|||
Index: linux-2.6.25/drivers/serial/amba-pl010.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/serial/amba-pl010.c
|
||||
+++ linux-2.6.25/drivers/serial/amba-pl010.c
|
||||
@@ -52,11 +52,10 @@
|
||||
|
||||
#include <asm/io.h>
|
||||
|
||||
-#define UART_NR 8
|
||||
-
|
||||
#define SERIAL_AMBA_MAJOR 204
|
||||
#define SERIAL_AMBA_MINOR 16
|
||||
-#define SERIAL_AMBA_NR UART_NR
|
||||
+#define SERIAL_AMBA_NR CONFIG_SERIAL_AMBA_PL010_NUMPORTS
|
||||
+#define SERIAL_AMBA_NAME CONFIG_SERIAL_AMBA_PL010_PORTNAME
|
||||
|
||||
#define AMBA_ISR_PASS_LIMIT 256
|
||||
|
||||
@@ -82,7 +81,7 @@ static void pl010_stop_tx(struct uart_po
|
||||
struct uart_amba_port *uap = (struct uart_amba_port *)port;
|
||||
unsigned int cr;
|
||||
|
||||
- cr = readb(uap->port.membase + UART010_CR);
|
||||
+ cr = readl(uap->port.membase + UART010_CR);
|
||||
cr &= ~UART010_CR_TIE;
|
||||
writel(cr, uap->port.membase + UART010_CR);
|
||||
}
|
||||
@@ -92,7 +91,7 @@ static void pl010_start_tx(struct uart_p
|
||||
struct uart_amba_port *uap = (struct uart_amba_port *)port;
|
||||
unsigned int cr;
|
||||
|
||||
- cr = readb(uap->port.membase + UART010_CR);
|
||||
+ cr = readl(uap->port.membase + UART010_CR);
|
||||
cr |= UART010_CR_TIE;
|
||||
writel(cr, uap->port.membase + UART010_CR);
|
||||
}
|
||||
@@ -102,7 +101,7 @@ static void pl010_stop_rx(struct uart_po
|
||||
struct uart_amba_port *uap = (struct uart_amba_port *)port;
|
||||
unsigned int cr;
|
||||
|
||||
- cr = readb(uap->port.membase + UART010_CR);
|
||||
+ cr = readl(uap->port.membase + UART010_CR);
|
||||
cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
|
||||
writel(cr, uap->port.membase + UART010_CR);
|
||||
}
|
||||
@@ -112,7 +111,7 @@ static void pl010_enable_ms(struct uart_
|
||||
struct uart_amba_port *uap = (struct uart_amba_port *)port;
|
||||
unsigned int cr;
|
||||
|
||||
- cr = readb(uap->port.membase + UART010_CR);
|
||||
+ cr = readl(uap->port.membase + UART010_CR);
|
||||
cr |= UART010_CR_MSIE;
|
||||
writel(cr, uap->port.membase + UART010_CR);
|
||||
}
|
||||
@@ -122,9 +121,9 @@ static void pl010_rx_chars(struct uart_a
|
||||
struct tty_struct *tty = uap->port.info->tty;
|
||||
unsigned int status, ch, flag, rsr, max_count = 256;
|
||||
|
||||
- status = readb(uap->port.membase + UART01x_FR);
|
||||
+ status = readl(uap->port.membase + UART01x_FR);
|
||||
while (UART_RX_DATA(status) && max_count--) {
|
||||
- ch = readb(uap->port.membase + UART01x_DR);
|
||||
+ ch = readl(uap->port.membase + UART01x_DR);
|
||||
flag = TTY_NORMAL;
|
||||
|
||||
uap->port.icount.rx++;
|
||||
@@ -133,7 +132,7 @@ static void pl010_rx_chars(struct uart_a
|
||||
* Note that the error handling code is
|
||||
* out of the main execution path
|
||||
*/
|
||||
- rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
|
||||
+ rsr = readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
|
||||
if (unlikely(rsr & UART01x_RSR_ANY)) {
|
||||
writel(0, uap->port.membase + UART01x_ECR);
|
||||
|
||||
@@ -165,7 +164,7 @@ static void pl010_rx_chars(struct uart_a
|
||||
uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
|
||||
|
||||
ignore_char:
|
||||
- status = readb(uap->port.membase + UART01x_FR);
|
||||
+ status = readl(uap->port.membase + UART01x_FR);
|
||||
}
|
||||
spin_unlock(&uap->port.lock);
|
||||
tty_flip_buffer_push(tty);
|
||||
@@ -210,7 +209,7 @@ static void pl010_modem_status(struct ua
|
||||
|
||||
writel(0, uap->port.membase + UART010_ICR);
|
||||
|
||||
- status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
|
||||
+ status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
|
||||
|
||||
delta = status ^ uap->old_status;
|
||||
uap->old_status = status;
|
||||
@@ -238,7 +237,7 @@ static irqreturn_t pl010_int(int irq, vo
|
||||
|
||||
spin_lock(&uap->port.lock);
|
||||
|
||||
- status = readb(uap->port.membase + UART010_IIR);
|
||||
+ status = readl(uap->port.membase + UART010_IIR);
|
||||
if (status) {
|
||||
do {
|
||||
if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
|
||||
@@ -251,7 +250,7 @@ static irqreturn_t pl010_int(int irq, vo
|
||||
if (pass_counter-- == 0)
|
||||
break;
|
||||
|
||||
- status = readb(uap->port.membase + UART010_IIR);
|
||||
+ status = readl(uap->port.membase + UART010_IIR);
|
||||
} while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
|
||||
UART010_IIR_TIS));
|
||||
handled = 1;
|
||||
@@ -265,7 +264,7 @@ static irqreturn_t pl010_int(int irq, vo
|
||||
static unsigned int pl010_tx_empty(struct uart_port *port)
|
||||
{
|
||||
struct uart_amba_port *uap = (struct uart_amba_port *)port;
|
||||
- unsigned int status = readb(uap->port.membase + UART01x_FR);
|
||||
+ unsigned int status = readl(uap->port.membase + UART01x_FR);
|
||||
return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
|
||||
}
|
||||
|
||||
@@ -275,7 +274,7 @@ static unsigned int pl010_get_mctrl(stru
|
||||
unsigned int result = 0;
|
||||
unsigned int status;
|
||||
|
||||
- status = readb(uap->port.membase + UART01x_FR);
|
||||
+ status = readl(uap->port.membase + UART01x_FR);
|
||||
if (status & UART01x_FR_DCD)
|
||||
result |= TIOCM_CAR;
|
||||
if (status & UART01x_FR_DSR)
|
||||
@@ -301,7 +300,7 @@ static void pl010_break_ctl(struct uart_
|
||||
unsigned int lcr_h;
|
||||
|
||||
spin_lock_irqsave(&uap->port.lock, flags);
|
||||
- lcr_h = readb(uap->port.membase + UART010_LCRH);
|
||||
+ lcr_h = readl(uap->port.membase + UART010_LCRH);
|
||||
if (break_state == -1)
|
||||
lcr_h |= UART01x_LCRH_BRK;
|
||||
else
|
||||
@@ -334,7 +333,7 @@ static int pl010_startup(struct uart_por
|
||||
/*
|
||||
* initialise the old status of the modem signals
|
||||
*/
|
||||
- uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
|
||||
+ uap->old_status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
|
||||
|
||||
/*
|
||||
* Finally, enable interrupts
|
||||
@@ -365,7 +364,7 @@ static void pl010_shutdown(struct uart_p
|
||||
writel(0, uap->port.membase + UART010_CR);
|
||||
|
||||
/* disable break condition and fifos */
|
||||
- writel(readb(uap->port.membase + UART010_LCRH) &
|
||||
+ writel(readl(uap->port.membase + UART010_LCRH) &
|
||||
~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
|
||||
uap->port.membase + UART010_LCRH);
|
||||
|
||||
@@ -387,7 +386,7 @@ pl010_set_termios(struct uart_port *port
|
||||
/*
|
||||
* Ask the core to calculate the divisor for us.
|
||||
*/
|
||||
- baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
|
||||
+ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
|
||||
quot = uart_get_divisor(port, baud);
|
||||
|
||||
switch (termios->c_cflag & CSIZE) {
|
||||
@@ -450,7 +449,7 @@ pl010_set_termios(struct uart_port *port
|
||||
uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
|
||||
|
||||
/* first, disable everything */
|
||||
- old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
|
||||
+ old_cr = readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
|
||||
|
||||
if (UART_ENABLE_MS(port, termios->c_cflag))
|
||||
old_cr |= UART010_CR_MSIE;
|
||||
@@ -540,7 +539,7 @@ static struct uart_ops amba_pl010_pops =
|
||||
.verify_port = pl010_verify_port,
|
||||
};
|
||||
|
||||
-static struct uart_amba_port *amba_ports[UART_NR];
|
||||
+static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
|
||||
|
||||
#ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
|
||||
|
||||
@@ -550,7 +549,7 @@ static void pl010_console_putchar(struct
|
||||
unsigned int status;
|
||||
|
||||
do {
|
||||
- status = readb(uap->port.membase + UART01x_FR);
|
||||
+ status = readl(uap->port.membase + UART01x_FR);
|
||||
barrier();
|
||||
} while (!UART_TX_READY(status));
|
||||
writel(ch, uap->port.membase + UART01x_DR);
|
||||
@@ -567,7 +566,7 @@ pl010_console_write(struct console *co,
|
||||
/*
|
||||
* First save the CR then disable the interrupts
|
||||
*/
|
||||
- old_cr = readb(uap->port.membase + UART010_CR);
|
||||
+ old_cr = readl(uap->port.membase + UART010_CR);
|
||||
writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
|
||||
|
||||
uart_console_write(&uap->port, s, count, pl010_console_putchar);
|
||||
@@ -577,7 +576,7 @@ pl010_console_write(struct console *co,
|
||||
* and restore the TCR
|
||||
*/
|
||||
do {
|
||||
- status = readb(uap->port.membase + UART01x_FR);
|
||||
+ status = readl(uap->port.membase + UART01x_FR);
|
||||
barrier();
|
||||
} while (status & UART01x_FR_BUSY);
|
||||
writel(old_cr, uap->port.membase + UART010_CR);
|
||||
@@ -589,9 +588,9 @@ static void __init
|
||||
pl010_console_get_options(struct uart_amba_port *uap, int *baud,
|
||||
int *parity, int *bits)
|
||||
{
|
||||
- if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
|
||||
+ if (readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
|
||||
unsigned int lcr_h, quot;
|
||||
- lcr_h = readb(uap->port.membase + UART010_LCRH);
|
||||
+ lcr_h = readl(uap->port.membase + UART010_LCRH);
|
||||
|
||||
*parity = 'n';
|
||||
if (lcr_h & UART01x_LCRH_PEN) {
|
||||
@@ -606,8 +605,8 @@ pl010_console_get_options(struct uart_am
|
||||
else
|
||||
*bits = 8;
|
||||
|
||||
- quot = readb(uap->port.membase + UART010_LCRL) |
|
||||
- readb(uap->port.membase + UART010_LCRM) << 8;
|
||||
+ quot = readl(uap->port.membase + UART010_LCRL) |
|
||||
+ readl(uap->port.membase + UART010_LCRM) << 8;
|
||||
*baud = uap->port.uartclk / (16 * (quot + 1));
|
||||
}
|
||||
}
|
||||
@@ -625,7 +624,7 @@ static int __init pl010_console_setup(st
|
||||
* if so, search for the first available port that does have
|
||||
* console support.
|
||||
*/
|
||||
- if (co->index >= UART_NR)
|
||||
+ if (co->index >= SERIAL_AMBA_NR)
|
||||
co->index = 0;
|
||||
uap = amba_ports[co->index];
|
||||
if (!uap)
|
||||
@@ -643,7 +642,7 @@ static int __init pl010_console_setup(st
|
||||
|
||||
static struct uart_driver amba_reg;
|
||||
static struct console amba_console = {
|
||||
- .name = "ttyAM",
|
||||
+ .name = SERIAL_AMBA_NAME,
|
||||
.write = pl010_console_write,
|
||||
.device = uart_console_device,
|
||||
.setup = pl010_console_setup,
|
||||
@@ -659,11 +658,11 @@ static struct console amba_console = {
|
||||
|
||||
static struct uart_driver amba_reg = {
|
||||
.owner = THIS_MODULE,
|
||||
- .driver_name = "ttyAM",
|
||||
- .dev_name = "ttyAM",
|
||||
+ .driver_name = SERIAL_AMBA_NAME,
|
||||
+ .dev_name = SERIAL_AMBA_NAME,
|
||||
.major = SERIAL_AMBA_MAJOR,
|
||||
.minor = SERIAL_AMBA_MINOR,
|
||||
- .nr = UART_NR,
|
||||
+ .nr = SERIAL_AMBA_NR,
|
||||
.cons = AMBA_CONSOLE,
|
||||
};
|
||||
|
||||
Index: linux-2.6.25/drivers/serial/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/serial/Kconfig
|
||||
+++ linux-2.6.25/drivers/serial/Kconfig
|
||||
@@ -287,10 +287,25 @@ config SERIAL_AMBA_PL010
|
||||
help
|
||||
This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
|
||||
an Integrator/AP or Integrator/PP2 platform, or if you have a
|
||||
- Cirrus Logic EP93xx CPU, say Y or M here.
|
||||
+ Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
|
||||
|
||||
If unsure, say N.
|
||||
|
||||
+config SERIAL_AMBA_PL010_NUMPORTS
|
||||
+ int "Maximum number of AMBA PL010 serial ports"
|
||||
+ depends on SERIAL_AMBA_PL010
|
||||
+ default "8"
|
||||
+ ---help---
|
||||
+ Set this to the number of serial ports you want the AMBA PL010 driver
|
||||
+ to support.
|
||||
+
|
||||
+config SERIAL_AMBA_PL010_PORTNAME
|
||||
+ string "Name of the AMBA PL010 serial ports"
|
||||
+ depends on SERIAL_AMBA_PL010
|
||||
+ default "ttyAM"
|
||||
+ ---help---
|
||||
+ ::: To be written :::
|
||||
+
|
||||
config SERIAL_AMBA_PL010_CONSOLE
|
||||
bool "Support for console on AMBA serial port"
|
||||
depends on SERIAL_AMBA_PL010=y
|
||||
|
|
@ -0,0 +1,15 @@
|
|||
Index: linux-2.6.25/drivers/amba/bus.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/amba/bus.c
|
||||
+++ linux-2.6.25/drivers/amba/bus.c
|
||||
@@ -17,6 +17,10 @@
|
||||
#include <asm/io.h>
|
||||
#include <asm/sizes.h>
|
||||
|
||||
+#ifndef NO_IRQ
|
||||
+#define NO_IRQ (-1)
|
||||
+#endif
|
||||
+
|
||||
#define to_amba_device(d) container_of(d, struct amba_device, dev)
|
||||
#define to_amba_driver(d) container_of(d, struct amba_driver, drv)
|
||||
|
||||
|
|
@ -0,0 +1,50 @@
|
|||
Index: linux-2.6.25/drivers/pci/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/pci/Kconfig
|
||||
+++ linux-2.6.25/drivers/pci/Kconfig
|
||||
@@ -42,6 +42,12 @@ config PCI_DEBUG
|
||||
|
||||
When in doubt, say N.
|
||||
|
||||
+config PCI_DISABLE_COMMON_QUIRKS
|
||||
+ bool "PCI disable common quirks"
|
||||
+ depends on PCI
|
||||
+ help
|
||||
+ If you don't know what to do here, say N.
|
||||
+
|
||||
config HT_IRQ
|
||||
bool "Interrupts on hypertransport devices"
|
||||
default y
|
||||
Index: linux-2.6.25/drivers/pci/quirks.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/pci/quirks.c
|
||||
+++ linux-2.6.25/drivers/pci/quirks.c
|
||||
@@ -24,6 +24,7 @@
|
||||
#include <linux/kallsyms.h>
|
||||
#include "pci.h"
|
||||
|
||||
+#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS
|
||||
/* The Mellanox Tavor device gives false positive parity errors
|
||||
* Mark this device with a broken_parity_status, to allow
|
||||
* PCI scanning code to "skip" this now blacklisted device.
|
||||
@@ -1495,6 +1496,7 @@ static void __devinit fixup_rev1_53c810(
|
||||
}
|
||||
}
|
||||
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810);
|
||||
+#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */
|
||||
|
||||
static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end)
|
||||
{
|
||||
@@ -1562,6 +1564,7 @@ void pci_fixup_device(enum pci_fixup_pas
|
||||
}
|
||||
EXPORT_SYMBOL(pci_fixup_device);
|
||||
|
||||
+#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS
|
||||
/* Enable 1k I/O space granularity on the Intel P64H2 */
|
||||
static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev)
|
||||
{
|
||||
@@ -1875,3 +1878,4 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AT
|
||||
quirk_msi_intx_disable_bug);
|
||||
|
||||
#endif /* CONFIG_PCI_MSI */
|
||||
+#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */
|
||||
|
|
@ -0,0 +1,29 @@
|
|||
Index: linux-2.6.25/drivers/leds/leds-gpio.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/leds/leds-gpio.c
|
||||
+++ linux-2.6.25/drivers/leds/leds-gpio.c
|
||||
@@ -41,13 +41,17 @@ static void gpio_led_set(struct led_clas
|
||||
container_of(led_cdev, struct gpio_led_data, cdev);
|
||||
int level;
|
||||
|
||||
- if (value == LED_OFF)
|
||||
- level = 0;
|
||||
- else
|
||||
- level = 1;
|
||||
-
|
||||
- if (led_dat->active_low)
|
||||
- level = !level;
|
||||
+ switch (value) {
|
||||
+ case LED_OFF:
|
||||
+ level = led_dat->active_low ? 1 : 0;
|
||||
+ break;
|
||||
+ case LED_FULL:
|
||||
+ level = led_dat->active_low ? 0 : 1;
|
||||
+ break;
|
||||
+ default:
|
||||
+ level = value;
|
||||
+ break;
|
||||
+ }
|
||||
|
||||
/* Setting GPIOs with I2C/etc requires a task context, and we don't
|
||||
* seem to have a reliable way to know if we're already in one; so
|
||||
|
|
@ -0,0 +1,35 @@
|
|||
Index: linux-2.6.25/drivers/watchdog/Kconfig
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/watchdog/Kconfig
|
||||
+++ linux-2.6.25/drivers/watchdog/Kconfig
|
||||
@@ -619,6 +619,18 @@ config SBC_EPX_C3_WATCHDOG
|
||||
|
||||
# MIPS Architecture
|
||||
|
||||
+config ADM5120_WDT
|
||||
+ tristate "Infineon ADM5120 SoC hardware watchdog"
|
||||
+ depends on WATCHDOG && MIPS_ADM5120
|
||||
+ help
|
||||
+ This is a driver for hardware watchdog integrated in Infineon
|
||||
+ ADM5120 SoC. This watchdog simply watches your kernel to make sure
|
||||
+ it doesn't freeze, and if it does, it reboots your computer after a
|
||||
+ certain amount of time.
|
||||
+
|
||||
+ To compile this driver as a module, choose M here: the module will be
|
||||
+ called adm5120_wdt.
|
||||
+
|
||||
config INDYDOG
|
||||
tristate "Indy/I2 Hardware Watchdog"
|
||||
depends on SGI_HAS_INDYDOG
|
||||
Index: linux-2.6.25/drivers/watchdog/Makefile
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/watchdog/Makefile
|
||||
+++ linux-2.6.25/drivers/watchdog/Makefile
|
||||
@@ -90,6 +90,7 @@ obj-$(CONFIG_SBC_EPX_C3_WATCHDOG) += sbc
|
||||
# M68KNOMMU Architecture
|
||||
|
||||
# MIPS Architecture
|
||||
+obj-$(CONFIG_ADM5120_WDT) += adm5120_wdt.o
|
||||
obj-$(CONFIG_INDYDOG) += indydog.o
|
||||
obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o
|
||||
obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o
|
||||
|
|
@ -0,0 +1,13 @@
|
|||
Index: linux-2.6.25/drivers/usb/host/adm5120-hcd.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/usb/host/adm5120-hcd.c
|
||||
+++ linux-2.6.25/drivers/usb/host/adm5120-hcd.c
|
||||
@@ -45,7 +45,7 @@
|
||||
#include "../core/hcd.h"
|
||||
#include "../core/hub.h"
|
||||
|
||||
-#define DRIVER_VERSION "0.24.0"
|
||||
+#define DRIVER_VERSION "0.25.0"
|
||||
#define DRIVER_AUTHOR "Gabor Juhos <juhosg at openwrt.org>"
|
||||
#define DRIVER_DESC "ADMtek USB 1.1 Host Controller Driver"
|
||||
|
||||
|
|
@ -0,0 +1,109 @@
|
|||
Index: linux-2.6.25/drivers/usb/host/adm5120-dbg.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/usb/host/adm5120-dbg.c
|
||||
+++ linux-2.6.25/drivers/usb/host/adm5120-dbg.c
|
||||
@@ -456,7 +456,7 @@ show_list(struct admhcd *ahcd, char *buf
|
||||
}
|
||||
|
||||
static ssize_t
|
||||
-show_async(struct class_device *class_dev, char *buf)
|
||||
+show_async(struct device *dev, struct device_attribute *attr, char *buf)
|
||||
{
|
||||
struct usb_bus *bus;
|
||||
struct usb_hcd *hcd;
|
||||
@@ -464,7 +464,7 @@ show_async(struct class_device *class_de
|
||||
size_t temp;
|
||||
unsigned long flags;
|
||||
|
||||
- bus = class_get_devdata(class_dev);
|
||||
+ bus = dev_get_drvdata(dev);
|
||||
hcd = bus_to_hcd(bus);
|
||||
ahcd = hcd_to_admhcd(hcd);
|
||||
|
||||
@@ -475,13 +475,13 @@ show_async(struct class_device *class_de
|
||||
|
||||
return temp;
|
||||
}
|
||||
-static CLASS_DEVICE_ATTR(async, S_IRUGO, show_async, NULL);
|
||||
+static DEVICE_ATTR(async, S_IRUGO, show_async, NULL);
|
||||
|
||||
|
||||
#define DBG_SCHED_LIMIT 64
|
||||
|
||||
static ssize_t
|
||||
-show_periodic(struct class_device *class_dev, char *buf)
|
||||
+show_periodic(struct device *dev, struct device_attribute *attr, char *buf)
|
||||
{
|
||||
struct usb_bus *bus;
|
||||
struct usb_hcd *hcd;
|
||||
@@ -496,7 +496,7 @@ show_periodic(struct class_device *class
|
||||
return 0;
|
||||
seen_count = 0;
|
||||
|
||||
- bus = class_get_devdata(class_dev);
|
||||
+ bus = dev_get_drvdata(dev);
|
||||
hcd = bus_to_hcd(bus);
|
||||
ahcd = hcd_to_admhcd(hcd);
|
||||
next = buf;
|
||||
@@ -574,13 +574,13 @@ show_periodic(struct class_device *class
|
||||
|
||||
return PAGE_SIZE - size;
|
||||
}
|
||||
-static CLASS_DEVICE_ATTR(periodic, S_IRUGO, show_periodic, NULL);
|
||||
+static DEVICE_ATTR(periodic, S_IRUGO, show_periodic, NULL);
|
||||
|
||||
|
||||
#undef DBG_SCHED_LIMIT
|
||||
|
||||
static ssize_t
|
||||
-show_registers(struct class_device *class_dev, char *buf)
|
||||
+show_registers(struct device *dev, struct device_attribute *attr, char *buf)
|
||||
{
|
||||
struct usb_bus *bus;
|
||||
struct usb_hcd *hcd;
|
||||
@@ -591,7 +591,7 @@ show_registers(struct class_device *clas
|
||||
char *next;
|
||||
u32 rdata;
|
||||
|
||||
- bus = class_get_devdata(class_dev);
|
||||
+ bus = dev_get_drvdata(dev);
|
||||
hcd = bus_to_hcd(bus);
|
||||
ahcd = hcd_to_admhcd(hcd);
|
||||
regs = ahcd->regs;
|
||||
@@ -656,27 +656,27 @@ done:
|
||||
spin_unlock_irqrestore(&ahcd->lock, flags);
|
||||
return PAGE_SIZE - size;
|
||||
}
|
||||
-static CLASS_DEVICE_ATTR(registers, S_IRUGO, show_registers, NULL);
|
||||
+static DEVICE_ATTR(registers, S_IRUGO, show_registers, NULL);
|
||||
|
||||
|
||||
static inline void create_debug_files (struct admhcd *ahcd)
|
||||
{
|
||||
- struct class_device *cldev = admhcd_to_hcd(ahcd)->self.class_dev;
|
||||
+ struct device *dev = admhcd_to_hcd(ahcd)->self.dev;
|
||||
int retval;
|
||||
|
||||
- retval = class_device_create_file(cldev, &class_device_attr_async);
|
||||
- retval = class_device_create_file(cldev, &class_device_attr_periodic);
|
||||
- retval = class_device_create_file(cldev, &class_device_attr_registers);
|
||||
+ retval = device_create_file(dev, &dev_attr_async);
|
||||
+ retval = device_create_file(dev, &dev_attr_periodic);
|
||||
+ retval = device_create_file(dev, &dev_attr_registers);
|
||||
admhc_dbg(ahcd, "created debug files\n");
|
||||
}
|
||||
|
||||
static inline void remove_debug_files (struct admhcd *ahcd)
|
||||
{
|
||||
- struct class_device *cldev = admhcd_to_hcd(ahcd)->self.class_dev;
|
||||
+ struct device *dev = admhcd_to_hcd(ahcd)->self.dev;
|
||||
|
||||
- class_device_remove_file(cldev, &class_device_attr_async);
|
||||
- class_device_remove_file(cldev, &class_device_attr_periodic);
|
||||
- class_device_remove_file(cldev, &class_device_attr_registers);
|
||||
+ device_remove_file(dev, &dev_attr_async);
|
||||
+ device_remove_file(dev, &dev_attr_periodic);
|
||||
+ device_remove_file(dev, &dev_attr_registers);
|
||||
}
|
||||
|
||||
#endif
|
||||
|
|
@ -0,0 +1,363 @@
|
|||
Index: linux-2.6.25/drivers/usb/host/adm5120.h
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/usb/host/adm5120.h
|
||||
+++ linux-2.6.25/drivers/usb/host/adm5120.h
|
||||
@@ -431,6 +431,13 @@ struct admhcd {
|
||||
#define OHCI_QUIRK_BE_MMIO 0x10 /* BE registers */
|
||||
#define OHCI_QUIRK_ZFMICRO 0x20 /* Compaq ZFMicro chipset*/
|
||||
// there are also chip quirks/bugs in init logic
|
||||
+
|
||||
+#ifdef DEBUG
|
||||
+ struct dentry *debug_dir;
|
||||
+ struct dentry *debug_async;
|
||||
+ struct dentry *debug_periodic;
|
||||
+ struct dentry *debug_registers;
|
||||
+#endif
|
||||
};
|
||||
|
||||
/* convert between an hcd pointer and the corresponding ahcd_hcd */
|
||||
Index: linux-2.6.25/drivers/usb/host/adm5120-hcd.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/usb/host/adm5120-hcd.c
|
||||
+++ linux-2.6.25/drivers/usb/host/adm5120-hcd.c
|
||||
@@ -35,6 +35,7 @@
|
||||
#include <linux/dma-mapping.h>
|
||||
#include <linux/dmapool.h>
|
||||
#include <linux/reboot.h>
|
||||
+#include <linux/debugfs.h>
|
||||
|
||||
#include <asm/io.h>
|
||||
#include <asm/irq.h>
|
||||
@@ -799,6 +800,14 @@ static int __init admhc_hcd_mod_init(voi
|
||||
pr_info("%s: block sizes: ed %Zd td %Zd\n", hcd_name,
|
||||
sizeof (struct ed), sizeof (struct td));
|
||||
|
||||
+#ifdef DEBUG
|
||||
+ admhc_debug_root = debugfs_create_dir("admhc", NULL);
|
||||
+ if (!admhc_debug_root) {
|
||||
+ ret = -ENOENT;
|
||||
+ goto error_debug;
|
||||
+ }
|
||||
+#endif
|
||||
+
|
||||
#ifdef PLATFORM_DRIVER
|
||||
ret = platform_driver_register(&PLATFORM_DRIVER);
|
||||
if (ret < 0)
|
||||
@@ -811,6 +820,12 @@ static int __init admhc_hcd_mod_init(voi
|
||||
platform_driver_unregister(&PLATFORM_DRIVER);
|
||||
error_platform:
|
||||
#endif
|
||||
+
|
||||
+#ifdef DEBUG
|
||||
+ debugfs_remove(admhc_debug_root);
|
||||
+ admhc_debug_root = NULL;
|
||||
+error_debug:
|
||||
+#endif
|
||||
return ret;
|
||||
}
|
||||
module_init(admhc_hcd_mod_init);
|
||||
@@ -818,6 +833,9 @@ module_init(admhc_hcd_mod_init);
|
||||
static void __exit admhc_hcd_mod_exit(void)
|
||||
{
|
||||
platform_driver_unregister(&PLATFORM_DRIVER);
|
||||
+#ifdef DEBUG
|
||||
+ debugfs_remove(admhc_debug_root);
|
||||
+#endif
|
||||
}
|
||||
module_exit(admhc_hcd_mod_exit);
|
||||
|
||||
Index: linux-2.6.25/drivers/usb/host/adm5120-dbg.c
|
||||
===================================================================
|
||||
--- linux-2.6.25.orig/drivers/usb/host/adm5120-dbg.c
|
||||
+++ linux-2.6.25/drivers/usb/host/adm5120-dbg.c
|
||||
@@ -390,6 +390,42 @@ static inline void remove_debug_files(st
|
||||
|
||||
#else
|
||||
|
||||
+static int debug_async_open(struct inode *, struct file *);
|
||||
+static int debug_periodic_open(struct inode *, struct file *);
|
||||
+static int debug_registers_open(struct inode *, struct file *);
|
||||
+static int debug_async_open(struct inode *, struct file *);
|
||||
+static ssize_t debug_output(struct file*, char __user*, size_t, loff_t*);
|
||||
+static int debug_close(struct inode *, struct file *);
|
||||
+
|
||||
+static const struct file_operations debug_async_fops = {
|
||||
+ .owner = THIS_MODULE,
|
||||
+ .open = debug_async_open,
|
||||
+ .read = debug_output,
|
||||
+ .release = debug_close,
|
||||
+};
|
||||
+static const struct file_operations debug_periodic_fops = {
|
||||
+ .owner = THIS_MODULE,
|
||||
+ .open = debug_periodic_open,
|
||||
+ .read = debug_output,
|
||||
+ .release = debug_close,
|
||||
+};
|
||||
+static const struct file_operations debug_registers_fops = {
|
||||
+ .owner = THIS_MODULE,
|
||||
+ .open = debug_registers_open,
|
||||
+ .read = debug_output,
|
||||
+ .release = debug_close,
|
||||
+};
|
||||
+
|
||||
+static struct dentry *admhc_debug_root;
|
||||
+
|
||||
+struct debug_buffer {
|
||||
+ ssize_t (*fill_func)(struct debug_buffer *); /* fill method */
|
||||
+ struct device *dev;
|
||||
+ struct mutex mutex; /* protect filling of buffer */
|
||||
+ size_t count; /* number of characters filled into buffer */
|
||||
+ char *page;
|
||||
+};
|
||||
+
|
||||
static ssize_t
|
||||
show_list(struct admhcd *ahcd, char *buf, size_t count, struct ed *ed)
|
||||
{
|
||||
@@ -455,8 +491,7 @@ show_list(struct admhcd *ahcd, char *buf
|
||||
return count - size;
|
||||
}
|
||||
|
||||
-static ssize_t
|
||||
-show_async(struct device *dev, struct device_attribute *attr, char *buf)
|
||||
+static ssize_t fill_async_buffer(struct debug_buffer *buf)
|
||||
{
|
||||
struct usb_bus *bus;
|
||||
struct usb_hcd *hcd;
|
||||
@@ -464,24 +499,22 @@ show_async(struct device *dev, struct de
|
||||
size_t temp;
|
||||
unsigned long flags;
|
||||
|
||||
- bus = dev_get_drvdata(dev);
|
||||
+ bus = dev_get_drvdata(buf->dev);
|
||||
hcd = bus_to_hcd(bus);
|
||||
ahcd = hcd_to_admhcd(hcd);
|
||||
|
||||
/* display control and bulk lists together, for simplicity */
|
||||
spin_lock_irqsave(&ahcd->lock, flags);
|
||||
- temp = show_list(ahcd, buf, PAGE_SIZE, ahcd->ed_head);
|
||||
+ temp = show_list(ahcd, buf->page, buf->count, ahcd->ed_head);
|
||||
spin_unlock_irqrestore(&ahcd->lock, flags);
|
||||
|
||||
return temp;
|
||||
}
|
||||
-static DEVICE_ATTR(async, S_IRUGO, show_async, NULL);
|
||||
|
||||
|
||||
#define DBG_SCHED_LIMIT 64
|
||||
|
||||
-static ssize_t
|
||||
-show_periodic(struct device *dev, struct device_attribute *attr, char *buf)
|
||||
+static ssize_t fill_periodic_buffer(struct debug_buffer *buf)
|
||||
{
|
||||
struct usb_bus *bus;
|
||||
struct usb_hcd *hcd;
|
||||
@@ -496,10 +529,10 @@ show_periodic(struct device *dev, struct
|
||||
return 0;
|
||||
seen_count = 0;
|
||||
|
||||
- bus = dev_get_drvdata(dev);
|
||||
+ bus = dev_get_drvdata(buf->dev);
|
||||
hcd = bus_to_hcd(bus);
|
||||
ahcd = hcd_to_admhcd(hcd);
|
||||
- next = buf;
|
||||
+ next = buf->page;
|
||||
size = PAGE_SIZE;
|
||||
|
||||
temp = scnprintf(next, size, "size = %d\n", NUM_INTS);
|
||||
@@ -574,13 +607,11 @@ show_periodic(struct device *dev, struct
|
||||
|
||||
return PAGE_SIZE - size;
|
||||
}
|
||||
-static DEVICE_ATTR(periodic, S_IRUGO, show_periodic, NULL);
|
||||
|
||||
|
||||
#undef DBG_SCHED_LIMIT
|
||||
|
||||
-static ssize_t
|
||||
-show_registers(struct device *dev, struct device_attribute *attr, char *buf)
|
||||
+static ssize_t fill_registers_buffer(struct debug_buffer *buf)
|
||||
{
|
||||
struct usb_bus *bus;
|
||||
struct usb_hcd *hcd;
|
||||
@@ -591,11 +622,11 @@ show_registers(struct device *dev, struc
|
||||
char *next;
|
||||
u32 rdata;
|
||||
|
||||
- bus = dev_get_drvdata(dev);
|
||||
+ bus = dev_get_drvdata(buf->dev);
|
||||
hcd = bus_to_hcd(bus);
|
||||
ahcd = hcd_to_admhcd(hcd);
|
||||
regs = ahcd->regs;
|
||||
- next = buf;
|
||||
+ next = buf->page;
|
||||
size = PAGE_SIZE;
|
||||
|
||||
spin_lock_irqsave(&ahcd->lock, flags);
|
||||
@@ -656,27 +687,154 @@ done:
|
||||
spin_unlock_irqrestore(&ahcd->lock, flags);
|
||||
return PAGE_SIZE - size;
|
||||
}
|
||||
-static DEVICE_ATTR(registers, S_IRUGO, show_registers, NULL);
|
||||
|
||||
|
||||
-static inline void create_debug_files (struct admhcd *ahcd)
|
||||
+static struct debug_buffer *alloc_buffer(struct device *dev,
|
||||
+ ssize_t (*fill_func)(struct debug_buffer *))
|
||||
{
|
||||
- struct device *dev = admhcd_to_hcd(ahcd)->self.dev;
|
||||
- int retval;
|
||||
+ struct debug_buffer *buf;
|
||||
|
||||
- retval = device_create_file(dev, &dev_attr_async);
|
||||
- retval = device_create_file(dev, &dev_attr_periodic);
|
||||
- retval = device_create_file(dev, &dev_attr_registers);
|
||||
- admhc_dbg(ahcd, "created debug files\n");
|
||||
+ buf = kzalloc(sizeof(struct debug_buffer), GFP_KERNEL);
|
||||
+
|
||||
+ if (buf) {
|
||||
+ buf->dev = dev;
|
||||
+ buf->fill_func = fill_func;
|
||||
+ mutex_init(&buf->mutex);
|
||||
+ }
|
||||
+
|
||||
+ return buf;
|
||||
+}
|
||||
+
|
||||
+static int fill_buffer(struct debug_buffer *buf)
|
||||
+{
|
||||
+ int ret = 0;
|
||||
+
|
||||
+ if (!buf->page)
|
||||
+ buf->page = (char *)get_zeroed_page(GFP_KERNEL);
|
||||
+
|
||||
+ if (!buf->page) {
|
||||
+ ret = -ENOMEM;
|
||||
+ goto out;
|
||||
+ }
|
||||
+
|
||||
+ ret = buf->fill_func(buf);
|
||||
+
|
||||
+ if (ret >= 0) {
|
||||
+ buf->count = ret;
|
||||
+ ret = 0;
|
||||
+ }
|
||||
+
|
||||
+out:
|
||||
+ return ret;
|
||||
+}
|
||||
+
|
||||
+static ssize_t debug_output(struct file *file, char __user *user_buf,
|
||||
+ size_t len, loff_t *offset)
|
||||
+{
|
||||
+ struct debug_buffer *buf = file->private_data;
|
||||
+ int ret = 0;
|
||||
+
|
||||
+ mutex_lock(&buf->mutex);
|
||||
+ if (buf->count == 0) {
|
||||
+ ret = fill_buffer(buf);
|
||||
+ if (ret != 0) {
|
||||
+ mutex_unlock(&buf->mutex);
|
||||
+ goto out;
|
||||
+ }
|
||||
+ }
|
||||
+ mutex_unlock(&buf->mutex);
|
||||
+
|
||||
+ ret = simple_read_from_buffer(user_buf, len, offset,
|
||||
+ buf->page, buf->count);
|
||||
+
|
||||
+out:
|
||||
+ return ret;
|
||||
+}
|
||||
+
|
||||
+static int debug_close(struct inode *inode, struct file *file)
|
||||
+{
|
||||
+ struct debug_buffer *buf = file->private_data;
|
||||
+
|
||||
+ if (buf) {
|
||||
+ if (buf->page)
|
||||
+ free_page((unsigned long)buf->page);
|
||||
+ kfree(buf);
|
||||
+ }
|
||||
+
|
||||
+ return 0;
|
||||
}
|
||||
|
||||
-static inline void remove_debug_files (struct admhcd *ahcd)
|
||||
+static int debug_async_open(struct inode *inode, struct file *file)
|
||||
{
|
||||
- struct device *dev = admhcd_to_hcd(ahcd)->self.dev;
|
||||
+ file->private_data = alloc_buffer(inode->i_private, fill_async_buffer);
|
||||
+
|
||||
+ return file->private_data ? 0 : -ENOMEM;
|
||||
+}
|
||||
+
|
||||
+static int debug_periodic_open(struct inode *inode, struct file *file)
|
||||
+{
|
||||
+ file->private_data = alloc_buffer(inode->i_private,
|
||||
+ fill_periodic_buffer);
|
||||
+
|
||||
+ return file->private_data ? 0 : -ENOMEM;
|
||||
+}
|
||||
|
||||
- device_remove_file(dev, &dev_attr_async);
|
||||
- device_remove_file(dev, &dev_attr_periodic);
|
||||
- device_remove_file(dev, &dev_attr_registers);
|
||||
+static int debug_registers_open(struct inode *inode, struct file *file)
|
||||
+{
|
||||
+ file->private_data = alloc_buffer(inode->i_private,
|
||||
+ fill_registers_buffer);
|
||||
+
|
||||
+ return file->private_data ? 0 : -ENOMEM;
|
||||
+}
|
||||
+
|
||||
+static inline void create_debug_files(struct admhcd *ahcd)
|
||||
+{
|
||||
+ struct usb_bus *bus = &admhcd_to_hcd(ahcd)->self;
|
||||
+ struct device *dev = bus->dev;
|
||||
+
|
||||
+ ahcd->debug_dir = debugfs_create_dir(bus->bus_name, admhc_debug_root);
|
||||
+ if (!ahcd->debug_dir)
|
||||
+ goto dir_error;
|
||||
+
|
||||
+ ahcd->debug_async = debugfs_create_file("async", S_IRUGO,
|
||||
+ ahcd->debug_dir, dev,
|
||||
+ &debug_async_fops);
|
||||
+ if (!ahcd->debug_async)
|
||||
+ goto async_error;
|
||||
+
|
||||
+ ahcd->debug_periodic = debugfs_create_file("periodic", S_IRUGO,
|
||||
+ ahcd->debug_dir, dev,
|
||||
+ &debug_periodic_fops);
|
||||
+ if (!ahcd->debug_periodic)
|
||||
+ goto periodic_error;
|
||||
+
|
||||
+ ahcd->debug_registers = debugfs_create_file("registers", S_IRUGO,
|
||||
+ ahcd->debug_dir, dev,
|
||||
+ &debug_registers_fops);
|
||||
+ if (!ahcd->debug_registers)
|
||||
+ goto registers_error;
|
||||
+
|
||||
+ admhc_dbg(ahcd, "created debug files\n");
|
||||
+ return;
|
||||
+
|
||||
+registers_error:
|
||||
+ debugfs_remove(ahcd->debug_periodic);
|
||||
+periodic_error:
|
||||
+ debugfs_remove(ahcd->debug_async);
|
||||
+async_error:
|
||||
+ debugfs_remove(ahcd->debug_dir);
|
||||
+dir_error:
|
||||
+ ahcd->debug_periodic = NULL;
|
||||
+ ahcd->debug_async = NULL;
|
||||
+ ahcd->debug_dir = NULL;
|
||||
+}
|
||||
+
|
||||
+static inline void remove_debug_files(struct admhcd *ahcd)
|
||||
+{
|
||||
+ debugfs_remove(ahcd->debug_registers);
|
||||
+ debugfs_remove(ahcd->debug_periodic);
|
||||
+ debugfs_remove(ahcd->debug_async);
|
||||
+ debugfs_remove(ahcd->debug_dir);
|
||||
}
|
||||
|
||||
#endif
|
||||
|
|
@ -0,0 +1,278 @@
|
|||
CONFIG_32BIT=y
|
||||
# CONFIG_64BIT is not set
|
||||
CONFIG_ADM5120_CPU_OVERRIDES=y
|
||||
CONFIG_ADM5120_WDT=y
|
||||
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
|
||||
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
|
||||
CONFIG_ARCH_POPULATES_NODE_MAP=y
|
||||
# CONFIG_ARCH_SUPPORTS_MSI is not set
|
||||
CONFIG_ARCH_SUPPORTS_OPROFILE=y
|
||||
CONFIG_ARCH_SUSPEND_POSSIBLE=y
|
||||
CONFIG_ARM_AMBA=y
|
||||
CONFIG_BASE_SMALL=0
|
||||
CONFIG_BAYCOM_SER_FDX=m
|
||||
CONFIG_BAYCOM_SER_HDX=m
|
||||
# CONFIG_BCM47XX is not set
|
||||
CONFIG_BINFMT_MISC=m
|
||||
CONFIG_BITREVERSE=y
|
||||
CONFIG_CEVT_R4K=y
|
||||
CONFIG_CIFS_DEBUG2=y
|
||||
CONFIG_CIFS_EXPERIMENTAL=y
|
||||
CONFIG_CIFS_STATS2=y
|
||||
CONFIG_CIFS_WEAK_PW_HASH=y
|
||||
CONFIG_CIFS_XATTR=y
|
||||
CONFIG_CLASSIC_RCU=y
|
||||
CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2 init=/etc/preinit"
|
||||
CONFIG_CPU_BIG_ENDIAN=y
|
||||
CONFIG_CPU_HAS_LLSC=y
|
||||
CONFIG_CPU_HAS_PREFETCH=y
|
||||
CONFIG_CPU_HAS_SYNC=y
|
||||
# CONFIG_CPU_LITTLE_ENDIAN is not set
|
||||
# CONFIG_CPU_LOONGSON2 is not set
|
||||
CONFIG_CPU_MIPS32=y
|
||||
CONFIG_CPU_MIPS32_R1=y
|
||||
# CONFIG_CPU_MIPS32_R2 is not set
|
||||
# CONFIG_CPU_MIPS64_R1 is not set
|
||||
# CONFIG_CPU_MIPS64_R2 is not set
|
||||
CONFIG_CPU_MIPSR1=y
|
||||
# CONFIG_CPU_NEVADA is not set
|
||||
# CONFIG_CPU_R10000 is not set
|
||||
# CONFIG_CPU_R3000 is not set
|
||||
# CONFIG_CPU_R4300 is not set
|
||||
# CONFIG_CPU_R4X00 is not set
|
||||
# CONFIG_CPU_R5000 is not set
|
||||
# CONFIG_CPU_R5432 is not set
|
||||
# CONFIG_CPU_R6000 is not set
|
||||
# CONFIG_CPU_R8000 is not set
|
||||
# CONFIG_CPU_RM7000 is not set
|
||||
# CONFIG_CPU_RM9000 is not set
|
||||
# CONFIG_CPU_SB1 is not set
|
||||
CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
|
||||
CONFIG_CPU_SUPPORTS_HIGHMEM=y
|
||||
# CONFIG_CPU_TX39XX is not set
|
||||
# CONFIG_CPU_TX49XX is not set
|
||||
# CONFIG_CPU_VR41XX is not set
|
||||
CONFIG_CRYPTO_AEAD=m
|
||||
CONFIG_CRYPTO_AUTHENC=m
|
||||
CONFIG_CRYPTO_GF128MUL=m
|
||||
CONFIG_CSRC_R4K=y
|
||||
CONFIG_DEVPORT=y
|
||||
# CONFIG_DM9000 is not set
|
||||
CONFIG_DMA_NEED_PCI_MAP_STATE=y
|
||||
CONFIG_DMA_NONCOHERENT=y
|
||||
# CONFIG_E1000E is not set
|
||||
# CONFIG_E1000E_ENABLED is not set
|
||||
CONFIG_EARLY_PRINTK=y
|
||||
CONFIG_ELF_CORE=y
|
||||
# CONFIG_EXT3_FS_POSIX_ACL is not set
|
||||
# CONFIG_EXT3_FS_SECURITY is not set
|
||||
CONFIG_EXT3_FS_XATTR=y
|
||||
CONFIG_FS_MBCACHE=m
|
||||
CONFIG_FS_POSIX_ACL=y
|
||||
CONFIG_GENERIC_ACL=y
|
||||
CONFIG_GENERIC_CLOCKEVENTS=y
|
||||
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
|
||||
CONFIG_GENERIC_CMOS_UPDATE=y
|
||||
CONFIG_GENERIC_FIND_NEXT_BIT=y
|
||||
CONFIG_GENERIC_GPIO=y
|
||||
# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set
|
||||
CONFIG_HAS_DMA=y
|
||||
CONFIG_HAS_IOMEM=y
|
||||
CONFIG_HAS_IOPORT=y
|
||||
CONFIG_HAVE_IDE=y
|
||||
# CONFIG_HAVE_KPROBES is not set
|
||||
# CONFIG_HAVE_KRETPROBES is not set
|
||||
CONFIG_HAVE_OPROFILE=y
|
||||
CONFIG_HID=m
|
||||
CONFIG_HID_SUPPORT=y
|
||||
CONFIG_HW_HAS_PCI=y
|
||||
CONFIG_HW_RANDOM=y
|
||||
CONFIG_HZ=250
|
||||
# CONFIG_HZ_100 is not set
|
||||
CONFIG_HZ_250=y
|
||||
# CONFIG_I2C is not set
|
||||
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
|
||||
# CONFIG_IBM_NEW_EMAC_RGMII is not set
|
||||
# CONFIG_IBM_NEW_EMAC_TAH is not set
|
||||
# CONFIG_IBM_NEW_EMAC_ZMII is not set
|
||||
# CONFIG_IDE is not set
|
||||
# CONFIG_IGB is not set
|
||||
CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
|
||||
CONFIG_INITRAMFS_SOURCE=""
|
||||
CONFIG_INOTIFY=y
|
||||
CONFIG_INOTIFY_USER=y
|
||||
CONFIG_INPUT=m
|
||||
# CONFIG_INPUT_EVDEV is not set
|
||||
# CONFIG_IP1000 is not set
|
||||
CONFIG_IPV6_MIP6=m
|
||||
CONFIG_IPV6_PRIVACY=y
|
||||
CONFIG_IPV6_ROUTE_INFO=y
|
||||
CONFIG_IPV6_TUNNEL=m
|
||||
CONFIG_IP_NF_TARGET_CLUSTERIP=m
|
||||
CONFIG_IRQ_CPU=y
|
||||
# CONFIG_JOLIET is not set
|
||||
CONFIG_LEDS_ADM5120=m
|
||||
# CONFIG_LEDS_ADM5120_DIAG is not set
|
||||
# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set
|
||||
# CONFIG_LEDS_ALIX is not set
|
||||
CONFIG_LEDS_GPIO=m
|
||||
CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m
|
||||
CONFIG_LEGACY_PTYS=y
|
||||
CONFIG_LEGACY_PTY_COUNT=256
|
||||
# CONFIG_LEMOTE_FULONG is not set
|
||||
CONFIG_LZO_COMPRESS=m
|
||||
CONFIG_LZO_DECOMPRESS=m
|
||||
# CONFIG_MACH_ALCHEMY is not set
|
||||
# CONFIG_MACH_DECSTATION is not set
|
||||
# CONFIG_MACH_JAZZ is not set
|
||||
# CONFIG_MACH_VR41XX is not set
|
||||
# CONFIG_MEMSTICK is not set
|
||||
CONFIG_MII=m
|
||||
# CONFIG_MINIX_FS is not set
|
||||
CONFIG_MIPS=y
|
||||
CONFIG_MIPS_ADM5120=y
|
||||
CONFIG_MIPS_ADM5120_ENET=y
|
||||
# CONFIG_MIPS_ATLAS is not set
|
||||
# CONFIG_MIPS_COBALT is not set
|
||||
CONFIG_MIPS_L1_CACHE_SHIFT=5
|
||||
# CONFIG_MIPS_MALTA is not set
|
||||
CONFIG_MIPS_MT_DISABLED=y
|
||||
# CONFIG_MIPS_MT_SMP is not set
|
||||
# CONFIG_MIPS_MT_SMTC is not set
|
||||
# CONFIG_MIPS_SEAD is not set
|
||||
# CONFIG_MIPS_SIM is not set
|
||||
CONFIG_MODULE_FORCE_UNLOAD=y
|
||||
CONFIG_MTD=y
|
||||
# CONFIG_MTD_ABSENT is not set
|
||||
CONFIG_MTD_ADM5120=y
|
||||
CONFIG_MTD_BLKDEVS=y
|
||||
CONFIG_MTD_BLOCK=y
|
||||
CONFIG_MTD_BLOCK2MTD=y
|
||||
CONFIG_MTD_CFI=y
|
||||
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
|
||||
CONFIG_MTD_CFI_AMDSTD=y
|
||||
CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
|
||||
CONFIG_MTD_CFI_I1=y
|
||||
CONFIG_MTD_CFI_I2=y
|
||||
# CONFIG_MTD_CFI_I4 is not set
|
||||
# CONFIG_MTD_CFI_I8 is not set
|
||||
# CONFIG_MTD_CFI_INTELEXT is not set
|
||||
# CONFIG_MTD_CFI_STAA is not set
|
||||
CONFIG_MTD_CFI_UTIL=y
|
||||
CONFIG_MTD_CHAR=y
|
||||
CONFIG_MTD_CMDLINE_PARTS=y
|
||||
CONFIG_MTD_COMPLEX_MAPPINGS=y
|
||||
# CONFIG_MTD_CONCAT is not set
|
||||
# CONFIG_MTD_DEBUG is not set
|
||||
# CONFIG_MTD_DOC2000 is not set
|
||||
# CONFIG_MTD_DOC2001 is not set
|
||||
# CONFIG_MTD_DOC2001PLUS is not set
|
||||
CONFIG_MTD_GEN_PROBE=y
|
||||
# CONFIG_MTD_JEDECPROBE is not set
|
||||
CONFIG_MTD_MAP_BANK_WIDTH_1=y
|
||||
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
|
||||
CONFIG_MTD_MAP_BANK_WIDTH_2=y
|
||||
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
|
||||
CONFIG_MTD_MAP_BANK_WIDTH_4=y
|
||||
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
|
||||
# CONFIG_MTD_MTDRAM is not set
|
||||
# CONFIG_MTD_MYLOADER_PARTS is not set
|
||||
# CONFIG_MTD_ONENAND is not set
|
||||
CONFIG_MTD_PARTITIONS=y
|
||||
# CONFIG_MTD_PCI is not set
|
||||
# CONFIG_MTD_PHRAM is not set
|
||||
# CONFIG_MTD_PHYSMAP is not set
|
||||
# CONFIG_MTD_PLATRAM is not set
|
||||
# CONFIG_MTD_PMC551 is not set
|
||||
# CONFIG_MTD_RAM is not set
|
||||
# CONFIG_MTD_REDBOOT_PARTS is not set
|
||||
# CONFIG_MTD_ROM is not set
|
||||
# CONFIG_MTD_SLRAM is not set
|
||||
CONFIG_MTD_TRXSPLIT=y
|
||||
CONFIG_NETDEV_1000=y
|
||||
# CONFIG_NET_PCI is not set
|
||||
# CONFIG_NET_PKTGEN is not set
|
||||
# CONFIG_NET_VENDOR_3COM is not set
|
||||
# CONFIG_NO_IOPORT is not set
|
||||
# CONFIG_PAGE_SIZE_16KB is not set
|
||||
CONFIG_PAGE_SIZE_4KB=y
|
||||
# CONFIG_PAGE_SIZE_64KB is not set
|
||||
# CONFIG_PAGE_SIZE_8KB is not set
|
||||
# CONFIG_PARTITION_ADVANCED is not set
|
||||
# CONFIG_PCIPCWATCHDOG is not set
|
||||
CONFIG_PCI_ADM5120=y
|
||||
CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
|
||||
CONFIG_PCI_DOMAINS=y
|
||||
# CONFIG_PMC_MSP is not set
|
||||
# CONFIG_PMC_YOSEMITE is not set
|
||||
# CONFIG_PNX8550_JBS is not set
|
||||
# CONFIG_PNX8550_STB810 is not set
|
||||
# CONFIG_RTC is not set
|
||||
CONFIG_RTC_LIB=y
|
||||
CONFIG_RWSEM_GENERIC_SPINLOCK=y
|
||||
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
|
||||
CONFIG_SCSI_WAIT_SCAN=m
|
||||
# CONFIG_SERIAL_8250 is not set
|
||||
CONFIG_SERIAL_AMBA_PL010=y
|
||||
CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
|
||||
CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
|
||||
CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
|
||||
# CONFIG_SERIAL_AMBA_PL011 is not set
|
||||
CONFIG_SERIO=y
|
||||
# CONFIG_SERIO_AMBAKMI is not set
|
||||
# CONFIG_SERIO_I8042 is not set
|
||||
# CONFIG_SERIO_LIBPS2 is not set
|
||||
# CONFIG_SERIO_PCIPS2 is not set
|
||||
# CONFIG_SERIO_RAW is not set
|
||||
CONFIG_SERIO_SERPORT=y
|
||||
# CONFIG_SGI_IP22 is not set
|
||||
# CONFIG_SGI_IP27 is not set
|
||||
# CONFIG_SGI_IP28 is not set
|
||||
# CONFIG_SGI_IP32 is not set
|
||||
# CONFIG_SIBYTE_BIGSUR is not set
|
||||
# CONFIG_SIBYTE_CARMEL is not set
|
||||
# CONFIG_SIBYTE_CRHINE is not set
|
||||
# CONFIG_SIBYTE_CRHONE is not set
|
||||
# CONFIG_SIBYTE_LITTLESUR is not set
|
||||
# CONFIG_SIBYTE_RHONE is not set
|
||||
# CONFIG_SIBYTE_SENTOSA is not set
|
||||
# CONFIG_SIBYTE_SWARM is not set
|
||||
CONFIG_SLABINFO=y
|
||||
# CONFIG_SND_USB_AUDIO is not set
|
||||
CONFIG_SOFT_WATCHDOG=m
|
||||
# CONFIG_SPARSEMEM_STATIC is not set
|
||||
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
|
||||
CONFIG_SSB_POSSIBLE=y
|
||||
CONFIG_SYSVIPC_SYSCTL=y
|
||||
CONFIG_SYS_HAS_CPU_MIPS32_R1=y
|
||||
CONFIG_SYS_HAS_EARLY_PRINTK=y
|
||||
CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
|
||||
CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
|
||||
CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
|
||||
CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
|
||||
# CONFIG_THERMAL is not set
|
||||
CONFIG_TICK_ONESHOT=y
|
||||
CONFIG_TMPFS_POSIX_ACL=y
|
||||
# CONFIG_TOSHIBA_JMR3927 is not set
|
||||
# CONFIG_TOSHIBA_RBTX4927 is not set
|
||||
# CONFIG_TOSHIBA_RBTX4938 is not set
|
||||
CONFIG_TRAD_SIGNALS=y
|
||||
# CONFIG_USBPCWATCHDOG is not set
|
||||
# CONFIG_USB_ACM is not set
|
||||
CONFIG_USB_ADM5120_HCD=m
|
||||
# CONFIG_USB_ATM is not set
|
||||
# CONFIG_USB_CATC is not set
|
||||
# CONFIG_USB_DEVICEFS is not set
|
||||
# CONFIG_USB_EHCI_HCD is not set
|
||||
# CONFIG_USB_KAWETH is not set
|
||||
# CONFIG_USB_PEGASUS is not set
|
||||
# CONFIG_USB_PRINTER is not set
|
||||
# CONFIG_USB_R8A66597_HCD is not set
|
||||
# CONFIG_USB_SERIAL is not set
|
||||
# CONFIG_USB_STORAGE is not set
|
||||
# CONFIG_USB_UHCI_HCD is not set
|
||||
# CONFIG_USB_USBNET is not set
|
||||
# CONFIG_VGASTATE is not set
|
||||
CONFIG_VIDEO_V4L2_COMMON=m
|
||||
CONFIG_VM_EVENT_COUNTERS=y
|
||||
CONFIG_ZONE_DMA_FLAG=0
|
||||
|
|
@ -0,0 +1,293 @@
|
|||
CONFIG_32BIT=y
|
||||
# CONFIG_64BIT is not set
|
||||
CONFIG_ADM5120_CPU_OVERRIDES=y
|
||||
CONFIG_ADM5120_WDT=y
|
||||
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
|
||||
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
|
||||
CONFIG_ARCH_POPULATES_NODE_MAP=y
|
||||
# CONFIG_ARCH_SUPPORTS_MSI is not set
|
||||
CONFIG_ARCH_SUPPORTS_OPROFILE=y
|
||||
CONFIG_ARCH_SUSPEND_POSSIBLE=y
|
||||
CONFIG_ARM_AMBA=y
|
||||
CONFIG_BASE_SMALL=0
|
||||
CONFIG_BAYCOM_SER_FDX=m
|
||||
CONFIG_BAYCOM_SER_HDX=m
|
||||
# CONFIG_BCM47XX is not set
|
||||
CONFIG_BINFMT_MISC=m
|
||||
CONFIG_BITREVERSE=y
|
||||
CONFIG_CEVT_R4K=y
|
||||
CONFIG_CIFS_DEBUG2=y
|
||||
CONFIG_CIFS_EXPERIMENTAL=y
|
||||
CONFIG_CIFS_STATS2=y
|
||||
CONFIG_CIFS_WEAK_PW_HASH=y
|
||||
CONFIG_CIFS_XATTR=y
|
||||
CONFIG_CLASSIC_RCU=y
|
||||
CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2 init=/etc/preinit"
|
||||
# CONFIG_CPU_BIG_ENDIAN is not set
|
||||
CONFIG_CPU_HAS_LLSC=y
|
||||
CONFIG_CPU_HAS_PREFETCH=y
|
||||
CONFIG_CPU_HAS_SYNC=y
|
||||
CONFIG_CPU_LITTLE_ENDIAN=y
|
||||
# CONFIG_CPU_LOONGSON2 is not set
|
||||
CONFIG_CPU_MIPS32=y
|
||||
CONFIG_CPU_MIPS32_R1=y
|
||||
# CONFIG_CPU_MIPS32_R2 is not set
|
||||
# CONFIG_CPU_MIPS64_R1 is not set
|
||||
# CONFIG_CPU_MIPS64_R2 is not set
|
||||
CONFIG_CPU_MIPSR1=y
|
||||
# CONFIG_CPU_NEVADA is not set
|
||||
# CONFIG_CPU_R10000 is not set
|
||||
# CONFIG_CPU_R3000 is not set
|
||||
# CONFIG_CPU_R4300 is not set
|
||||
# CONFIG_CPU_R4X00 is not set
|
||||
# CONFIG_CPU_R5000 is not set
|
||||
# CONFIG_CPU_R5432 is not set
|
||||
# CONFIG_CPU_R6000 is not set
|
||||
# CONFIG_CPU_R8000 is not set
|
||||
# CONFIG_CPU_RM7000 is not set
|
||||
# CONFIG_CPU_RM9000 is not set
|
||||
# CONFIG_CPU_SB1 is not set
|
||||
CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
|
||||
CONFIG_CPU_SUPPORTS_HIGHMEM=y
|
||||
# CONFIG_CPU_TX39XX is not set
|
||||
# CONFIG_CPU_TX49XX is not set
|
||||
# CONFIG_CPU_VR41XX is not set
|
||||
CONFIG_CRYPTO_AEAD=m
|
||||
CONFIG_CRYPTO_AUTHENC=m
|
||||
CONFIG_CRYPTO_GF128MUL=m
|
||||
CONFIG_CSRC_R4K=y
|
||||
CONFIG_DEVPORT=y
|
||||
# CONFIG_DM9000 is not set
|
||||
CONFIG_DMA_NEED_PCI_MAP_STATE=y
|
||||
CONFIG_DMA_NONCOHERENT=y
|
||||
CONFIG_EARLY_PRINTK=y
|
||||
CONFIG_ELF_CORE=y
|
||||
# CONFIG_EXT3_FS_POSIX_ACL is not set
|
||||
# CONFIG_EXT3_FS_SECURITY is not set
|
||||
CONFIG_EXT3_FS_XATTR=y
|
||||
CONFIG_FS_MBCACHE=m
|
||||
CONFIG_FS_POSIX_ACL=y
|
||||
CONFIG_GENERIC_ACL=y
|
||||
CONFIG_GENERIC_CLOCKEVENTS=y
|
||||
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
|
||||
CONFIG_GENERIC_CMOS_UPDATE=y
|
||||
CONFIG_GENERIC_FIND_NEXT_BIT=y
|
||||
CONFIG_GENERIC_GPIO=y
|
||||
# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set
|
||||
CONFIG_HAS_DMA=y
|
||||
CONFIG_HAS_IOMEM=y
|
||||
CONFIG_HAS_IOPORT=y
|
||||
CONFIG_HAVE_IDE=y
|
||||
# CONFIG_HAVE_KPROBES is not set
|
||||
# CONFIG_HAVE_KRETPROBES is not set
|
||||
CONFIG_HAVE_OPROFILE=y
|
||||
CONFIG_HID=m
|
||||
CONFIG_HID_SUPPORT=y
|
||||
CONFIG_HW_HAS_PCI=y
|
||||
CONFIG_HW_RANDOM=y
|
||||
CONFIG_HZ=250
|
||||
# CONFIG_HZ_100 is not set
|
||||
CONFIG_HZ_250=y
|
||||
# CONFIG_I2C is not set
|
||||
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
|
||||
# CONFIG_IBM_NEW_EMAC_RGMII is not set
|
||||
# CONFIG_IBM_NEW_EMAC_TAH is not set
|
||||
# CONFIG_IBM_NEW_EMAC_ZMII is not set
|
||||
# CONFIG_IDE is not set
|
||||
CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
|
||||
CONFIG_INITRAMFS_SOURCE=""
|
||||
CONFIG_INOTIFY=y
|
||||
CONFIG_INOTIFY_USER=y
|
||||
CONFIG_INPUT=m
|
||||
# CONFIG_INPUT_EVDEV is not set
|
||||
CONFIG_IPV6_MIP6=m
|
||||
CONFIG_IPV6_PRIVACY=y
|
||||
CONFIG_IPV6_ROUTE_INFO=y
|
||||
CONFIG_IPV6_TUNNEL=m
|
||||
CONFIG_IP_NF_TARGET_CLUSTERIP=m
|
||||
CONFIG_IRQ_CPU=y
|
||||
# CONFIG_JOLIET is not set
|
||||
CONFIG_LEDS_ADM5120=m
|
||||
# CONFIG_LEDS_ADM5120_DIAG is not set
|
||||
# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set
|
||||
# CONFIG_LEDS_ALIX is not set
|
||||
CONFIG_LEDS_GPIO=m
|
||||
CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m
|
||||
CONFIG_LEGACY_PTYS=y
|
||||
CONFIG_LEGACY_PTY_COUNT=256
|
||||
# CONFIG_LEMOTE_FULONG is not set
|
||||
CONFIG_LZO_COMPRESS=m
|
||||
CONFIG_LZO_DECOMPRESS=m
|
||||
# CONFIG_MACH_ALCHEMY is not set
|
||||
# CONFIG_MACH_DECSTATION is not set
|
||||
# CONFIG_MACH_JAZZ is not set
|
||||
# CONFIG_MACH_VR41XX is not set
|
||||
# CONFIG_MEMSTICK is not set
|
||||
CONFIG_MII=m
|
||||
# CONFIG_MINIX_FS is not set
|
||||
CONFIG_MIPS=y
|
||||
CONFIG_MIPS_ADM5120=y
|
||||
CONFIG_MIPS_ADM5120_ENET=y
|
||||
# CONFIG_MIPS_ATLAS is not set
|
||||
# CONFIG_MIPS_COBALT is not set
|
||||
CONFIG_MIPS_L1_CACHE_SHIFT=5
|
||||
# CONFIG_MIPS_MALTA is not set
|
||||
CONFIG_MIPS_MT_DISABLED=y
|
||||
# CONFIG_MIPS_MT_SMP is not set
|
||||
# CONFIG_MIPS_MT_SMTC is not set
|
||||
# CONFIG_MIPS_SEAD is not set
|
||||
# CONFIG_MIPS_SIM is not set
|
||||
CONFIG_MODULE_FORCE_UNLOAD=y
|
||||
CONFIG_MTD=y
|
||||
# CONFIG_MTD_ABSENT is not set
|
||||
CONFIG_MTD_ADM5120=y
|
||||
# CONFIG_MTD_ALAUDA is not set
|
||||
CONFIG_MTD_BLKDEVS=y
|
||||
CONFIG_MTD_BLOCK=y
|
||||
# CONFIG_MTD_BLOCK2MTD is not set
|
||||
CONFIG_MTD_CFI=y
|
||||
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
|
||||
CONFIG_MTD_CFI_AMDSTD=y
|
||||
CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
|
||||
CONFIG_MTD_CFI_I1=y
|
||||
CONFIG_MTD_CFI_I2=y
|
||||
# CONFIG_MTD_CFI_I4 is not set
|
||||
# CONFIG_MTD_CFI_I8 is not set
|
||||
# CONFIG_MTD_CFI_INTELEXT is not set
|
||||
# CONFIG_MTD_CFI_STAA is not set
|
||||
CONFIG_MTD_CFI_UTIL=y
|
||||
CONFIG_MTD_CHAR=y
|
||||
CONFIG_MTD_CMDLINE_PARTS=y
|
||||
CONFIG_MTD_COMPLEX_MAPPINGS=y
|
||||
# CONFIG_MTD_CONCAT is not set
|
||||
# CONFIG_MTD_DEBUG is not set
|
||||
# CONFIG_MTD_DOC2000 is not set
|
||||
# CONFIG_MTD_DOC2001 is not set
|
||||
# CONFIG_MTD_DOC2001PLUS is not set
|
||||
CONFIG_MTD_GEN_PROBE=y
|
||||
CONFIG_MTD_JEDECPROBE=y
|
||||
CONFIG_MTD_MAP_BANK_WIDTH_1=y
|
||||
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
|
||||
CONFIG_MTD_MAP_BANK_WIDTH_2=y
|
||||
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
|
||||
CONFIG_MTD_MAP_BANK_WIDTH_4=y
|
||||
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
|
||||
# CONFIG_MTD_MTDRAM is not set
|
||||
CONFIG_MTD_MYLOADER_PARTS=y
|
||||
CONFIG_MTD_NAND=y
|
||||
# CONFIG_MTD_NAND_CAFE is not set
|
||||
# CONFIG_MTD_NAND_DISKONCHIP is not set
|
||||
# CONFIG_MTD_NAND_ECC_SMC is not set
|
||||
CONFIG_MTD_NAND_IDS=y
|
||||
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
|
||||
# CONFIG_MTD_NAND_NANDSIM is not set
|
||||
CONFIG_MTD_NAND_PLATFORM=y
|
||||
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
|
||||
# CONFIG_MTD_ONENAND is not set
|
||||
CONFIG_MTD_PARTITIONS=y
|
||||
# CONFIG_MTD_PCI is not set
|
||||
# CONFIG_MTD_PHRAM is not set
|
||||
# CONFIG_MTD_PHYSMAP is not set
|
||||
# CONFIG_MTD_PLATRAM is not set
|
||||
# CONFIG_MTD_PMC551 is not set
|
||||
# CONFIG_MTD_RAM is not set
|
||||
# CONFIG_MTD_REDBOOT_PARTS is not set
|
||||
# CONFIG_MTD_ROM is not set
|
||||
# CONFIG_MTD_SLRAM is not set
|
||||
CONFIG_MTD_TRXSPLIT=y
|
||||
# CONFIG_NETFILTER_XT_TARGET_TARPIT is not set
|
||||
# CONFIG_NET_PCI is not set
|
||||
# CONFIG_NET_PKTGEN is not set
|
||||
# CONFIG_NET_VENDOR_3COM is not set
|
||||
# CONFIG_NO_IOPORT is not set
|
||||
# CONFIG_PAGE_SIZE_16KB is not set
|
||||
CONFIG_PAGE_SIZE_4KB=y
|
||||
# CONFIG_PAGE_SIZE_64KB is not set
|
||||
# CONFIG_PAGE_SIZE_8KB is not set
|
||||
# CONFIG_PARTITION_ADVANCED is not set
|
||||
# CONFIG_PCIPCWATCHDOG is not set
|
||||
CONFIG_PCI_ADM5120=y
|
||||
CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
|
||||
CONFIG_PCI_DOMAINS=y
|
||||
# CONFIG_PMC_MSP is not set
|
||||
# CONFIG_PMC_YOSEMITE is not set
|
||||
# CONFIG_PNX8550_JBS is not set
|
||||
# CONFIG_PNX8550_STB810 is not set
|
||||
# CONFIG_RTC is not set
|
||||
CONFIG_RTC_LIB=y
|
||||
CONFIG_RWSEM_GENERIC_SPINLOCK=y
|
||||
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
|
||||
CONFIG_SCSI_WAIT_SCAN=m
|
||||
# CONFIG_SERIAL_8250 is not set
|
||||
CONFIG_SERIAL_AMBA_PL010=y
|
||||
CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
|
||||
CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
|
||||
CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
|
||||
# CONFIG_SERIAL_AMBA_PL011 is not set
|
||||
CONFIG_SERIO=y
|
||||
# CONFIG_SERIO_AMBAKMI is not set
|
||||
# CONFIG_SERIO_I8042 is not set
|
||||
# CONFIG_SERIO_LIBPS2 is not set
|
||||
# CONFIG_SERIO_PCIPS2 is not set
|
||||
# CONFIG_SERIO_RAW is not set
|
||||
CONFIG_SERIO_SERPORT=y
|
||||
# CONFIG_SGI_IP22 is not set
|
||||
# CONFIG_SGI_IP27 is not set
|
||||
# CONFIG_SGI_IP28 is not set
|
||||
# CONFIG_SGI_IP32 is not set
|
||||
# CONFIG_SIBYTE_BIGSUR is not set
|
||||
# CONFIG_SIBYTE_CARMEL is not set
|
||||
# CONFIG_SIBYTE_CRHINE is not set
|
||||
# CONFIG_SIBYTE_CRHONE is not set
|
||||
# CONFIG_SIBYTE_LITTLESUR is not set
|
||||
# CONFIG_SIBYTE_RHONE is not set
|
||||
# CONFIG_SIBYTE_SENTOSA is not set
|
||||
# CONFIG_SIBYTE_SWARM is not set
|
||||
CONFIG_SLABINFO=y
|
||||
# CONFIG_SND_HIFIER is not set
|
||||
# CONFIG_SND_OXYGEN is not set
|
||||
# CONFIG_SND_VIRTUOSO is not set
|
||||
CONFIG_SOFT_WATCHDOG=m
|
||||
# CONFIG_SPARSEMEM_STATIC is not set
|
||||
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
|
||||
CONFIG_SSB_POSSIBLE=y
|
||||
CONFIG_SYSVIPC_SYSCTL=y
|
||||
CONFIG_SYS_HAS_CPU_MIPS32_R1=y
|
||||
CONFIG_SYS_HAS_EARLY_PRINTK=y
|
||||
CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
|
||||
CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
|
||||
CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
|
||||
CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
|
||||
# CONFIG_THERMAL is not set
|
||||
CONFIG_TICK_ONESHOT=y
|
||||
CONFIG_TMPFS_POSIX_ACL=y
|
||||
# CONFIG_TOSHIBA_JMR3927 is not set
|
||||
# CONFIG_TOSHIBA_RBTX4927 is not set
|
||||
# CONFIG_TOSHIBA_RBTX4938 is not set
|
||||
CONFIG_TRAD_SIGNALS=y
|
||||
# CONFIG_USBPCWATCHDOG is not set
|
||||
CONFIG_USB_ADM5120_HCD=m
|
||||
# CONFIG_USB_ALI_M5632 is not set
|
||||
# CONFIG_USB_AN2720 is not set
|
||||
# CONFIG_USB_CATC is not set
|
||||
CONFIG_USB_DEBUG=y
|
||||
CONFIG_USB_EHCI_HCD=m
|
||||
# CONFIG_USB_KAWETH is not set
|
||||
# CONFIG_USB_NET_DM9601 is not set
|
||||
# CONFIG_USB_NET_GL620A is not set
|
||||
# CONFIG_USB_NET_MCS7830 is not set
|
||||
# CONFIG_USB_NET_PLUSB is not set
|
||||
# CONFIG_USB_NET_RNDIS_HOST is not set
|
||||
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
|
||||
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
|
||||
CONFIG_USB_OHCI_HCD=m
|
||||
# CONFIG_USB_PEGASUS is not set
|
||||
# CONFIG_USB_R8A66597_HCD is not set
|
||||
# CONFIG_USB_SERIAL is not set
|
||||
# CONFIG_USB_UHCI_HCD is not set
|
||||
# CONFIG_VGASTATE is not set
|
||||
CONFIG_VIDEO_V4L1=y
|
||||
CONFIG_VIDEO_V4L2_COMMON=m
|
||||
CONFIG_VM_EVENT_COUNTERS=y
|
||||
# CONFIG_XFRM_STATISTICS is not set
|
||||
CONFIG_ZONE_DMA_FLAG=0
|
||||
Loading…
Reference in New Issue