preliminary ixp4xx 2.6.28 support

SVN-Revision: 13548
2008-12-08 14:46:04 +00:00 · 2008-12-08 14:46:04 +00:00 · 8fd0b4373c
parent 47050e72be
commit 8fd0b4373c
37 changed files with 8294 additions and 0 deletions
--- a/target/linux/ixp4xx/config-2.6.28
+++ b/target/linux/ixp4xx/config-2.6.28
@ -0,0 +1,349 @@
+# CONFIG_8139TOO is not set
+# CONFIG_AEABI is not set
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_ADI_COYOTE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CLPS7500 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+CONFIG_ARCH_FLATMEM_HAS_HOLES=y
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+CONFIG_ARCH_IXCDP1100=y
+CONFIG_ARCH_IXDP425=y
+CONFIG_ARCH_IXDP4XX=y
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP23XX is not set
+CONFIG_ARCH_IXP4XX=y
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MSM7X00A is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PRPMC1100 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_SHARK is not set
+CONFIG_ARCH_SUPPORTS_AOUT=y
+CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+# CONFIG_ARCH_VERSATILE is not set
+CONFIG_ARM=y
+# CONFIG_ARM_THUMB is not set
+# CONFIG_ARPD is not set
+# CONFIG_ARTHUR is not set
+CONFIG_AT24=y
+CONFIG_ATA=m
+# CONFIG_ATA_NONSTANDARD is not set
+# CONFIG_ATA_PIIX is not set
+CONFIG_ATA_SFF=y
+# CONFIG_ATM is not set
+# CONFIG_ATMEL is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_BINFMT_AOUT is not set
+CONFIG_BITREVERSE=y
+# CONFIG_BONDING is not set
+CONFIG_BOUNCE=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_CIFS_STATS is not set
+CONFIG_CLASSIC_RCU=y
+CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 init=/etc/preinit"
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_CPU_32=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_BIG_ENDIAN=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_IXP43X=y
+CONFIG_CPU_IXP46X=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_XSCALE=y
+CONFIG_CRC16=y
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_USER is not set
+CONFIG_DEFAULT_TCP_CONG="westwood"
+# CONFIG_DEFAULT_VEGAS is not set
+CONFIG_DEFAULT_WESTWOOD=y
+CONFIG_DEVPORT=y
+# CONFIG_DM9000 is not set
+CONFIG_DMABOUNCE=y
+CONFIG_DMABOUNCE_DEBUG=y
+CONFIG_DNOTIFY=y
+# CONFIG_FPE_FASTFPE is not set
+# CONFIG_FPE_NWFPE is not set
+CONFIG_FRAME_POINTER=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
+# CONFIG_GENERIC_FIND_NEXT_BIT is not set
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_GPIO_DEVICE=y
+# CONFIG_HAMRADIO is not set
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_CLK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+CONFIG_HAVE_FTRACE=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_IDE=y
+# CONFIG_HAVE_IOREMAP_PROT is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HERMES is not set
+CONFIG_HID=m
+CONFIG_HID_SUPPORT=y
+CONFIG_HWMON=y
+# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_HWMON_VID=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_IXP4XX=y
+CONFIG_I2C=y
+CONFIG_I2C_ALGOBIT=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_GPIO=y
+# CONFIG_I2C_IOP3XX is not set
+# CONFIG_I2C_ISCH is not set
+# CONFIG_IDE is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INPUT=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+# CONFIG_ISDN is not set
+# CONFIG_IWMMXT is not set
+CONFIG_IXP4XX_ETH=y
+# CONFIG_IXP4XX_INDIRECT_PCI is not set
+CONFIG_IXP4XX_NPE=y
+CONFIG_IXP4XX_QMGR=y
+CONFIG_IXP4XX_WATCHDOG=y
+# CONFIG_LEDS_ALIX is not set
+CONFIG_LEDS_FSG=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_LATCH=y
+# CONFIG_LEDS_PCA9532 is not set
+# CONFIG_LEDS_PCA955X is not set
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_LLC2 is not set
+CONFIG_MACH_AP1000=y
+CONFIG_MACH_AVILA=y
+CONFIG_MACH_CAMBRIA=y
+CONFIG_MACH_COMPEX=y
+CONFIG_MACH_DSMG600=y
+CONFIG_MACH_FSG=y
+CONFIG_MACH_GATEWAY7001=y
+# CONFIG_MACH_GTWX5715 is not set
+# CONFIG_MACH_IXDP465 is not set
+CONFIG_MACH_IXDPG425=y
+# CONFIG_MACH_KIXRP435 is not set
+CONFIG_MACH_LOFT=y
+CONFIG_MACH_MI424WR=y
+CONFIG_MACH_NAS100D=y
+CONFIG_MACH_NSLU2=y
+CONFIG_MACH_PRONGHORN=y
+CONFIG_MACH_PRONGHORNMETRO=y
+CONFIG_MACH_SIDEWINDER=y
+CONFIG_MACH_TW5334=y
+CONFIG_MACH_USR8200=y
+CONFIG_MACH_WG302V1=y
+CONFIG_MACH_WG302V2=y
+CONFIG_MACH_WRT300NV2=y
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MEDIA_TUNER=m
+CONFIG_MEDIA_TUNER_MT20XX=m
+CONFIG_MEDIA_TUNER_SIMPLE=m
+CONFIG_MEDIA_TUNER_TDA8290=m
+CONFIG_MEDIA_TUNER_TDA9887=m
+CONFIG_MEDIA_TUNER_TEA5761=m
+CONFIG_MEDIA_TUNER_TEA5767=m
+CONFIG_MEDIA_TUNER_XC2028=m
+CONFIG_MEDIA_TUNER_XC5000=m
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MINIX_FS is not set
+CONFIG_MTD=y
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_MTD_BLOCK2MTD is not set
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_GEOMETRY is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
+CONFIG_MTD_CFI_NOSWAP=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_CHAR=y
+# CONFIG_MTD_CMDLINE_PARTS is not set
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_IXP4XX=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_ONENAND is not set
+CONFIG_MTD_OTP=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_PCI is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_PLATRAM is not set
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_RAM is not set
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
+CONFIG_MTD_REDBOOT_PARTS=y
+CONFIG_MTD_REDBOOT_PARTS_READONLY=y
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NO_IOPORT is not set
+# CONFIG_NVRAM is not set
+# CONFIG_OUTER_CACHE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_PATA_ARTOP=m
+CONFIG_PATA_IXP4XX_CF=m
+# CONFIG_PATA_SCH is not set
+CONFIG_PCI=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_R6040 is not set
+CONFIG_RFKILL_LEDS=y
+CONFIG_RTC_CLASS=y
+# CONFIG_RTC_DEBUG is not set
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+CONFIG_RTC_DRV_DS1672=y
+# CONFIG_RTC_DRV_DS1742 is not set
+CONFIG_RTC_DRV_ISL1208=y
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+CONFIG_RTC_DRV_PCF8563=y
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_TEST is not set
+# CONFIG_RTC_DRV_V3020 is not set
+CONFIG_RTC_DRV_X1205=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_LIB=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_SCSI_MULTI_LUN is not set
+CONFIG_SCSI_WAIT_SCAN=m
+# CONFIG_SENSORS_AD7414 is not set
+CONFIG_SENSORS_AD7418=y
+# CONFIG_SENSORS_EEPROM is not set
+CONFIG_SENSORS_MAX6650=y
+# CONFIG_SENSORS_PC87360 is not set
+CONFIG_SENSORS_W83781D=y
+# CONFIG_SERIAL_8250_EXTENDED is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+# CONFIG_SHMEM is not set
+CONFIG_SLABINFO=y
+# CONFIG_SND_ARM is not set
+CONFIG_SND_USB=y
+# CONFIG_SOFT_WATCHDOG is not set
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+CONFIG_SSB_POSSIBLE=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+# CONFIG_TCP_CONG_HSTCP is not set
+# CONFIG_TCP_CONG_HYBLA is not set
+# CONFIG_TCP_CONG_LP is not set
+# CONFIG_TCP_CONG_SCALABLE is not set
+CONFIG_TCP_CONG_VEGAS=m
+# CONFIG_TCP_CONG_VENO is not set
+CONFIG_TCP_CONG_WESTWOOD=y
+CONFIG_TICK_ONESHOT=y
+CONFIG_TINY_SHMEM=y
+CONFIG_UID16=y
+CONFIG_USB=m
+CONFIG_USB_EHCI_BIG_ENDIAN_DESC=y
+CONFIG_USB_EHCI_BIG_ENDIAN_MMIO=y
+CONFIG_USB_EHCI_HCD=m
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_EHCI_TT_NEWSCHED=y
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_HCD=m
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_UHCI_HCD=m
+CONFIG_VECTORS_BASE=0xffff0000
+# CONFIG_VGASTATE is not set
+# CONFIG_VIA_RHINE is not set
+CONFIG_VIA_VELOCITY=m
+CONFIG_VIDEO_MEDIA=m
+CONFIG_VIDEO_V4L2=m
+CONFIG_VIDEO_V4L2_COMMON=m
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_XSCALE_PMU=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
--- a/target/linux/ixp4xx/patches-2.6.28/010-ixp43x_pci_fixup.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/010-ixp43x_pci_fixup.patch
@ -0,0 +1,11 @@
+--- a/arch/arm/mach-ixp4xx/include/mach/hardware.h
+++ b/arch/arm/mach-ixp4xx/include/mach/hardware.h
+@@ -18,7 +18,7 @@
+ #define __ASM_ARCH_HARDWARE_H__
+ 
+ #define PCIBIOS_MIN_IO		0x00001000
+-#define PCIBIOS_MIN_MEM		(cpu_is_ixp43x() ? 0x40000000 : 0x48000000)
+#define PCIBIOS_MIN_MEM		0x48000000
+ 
+ /*
+  * We override the standard dma-mask routines for bouncing.
--- a/target/linux/ixp4xx/patches-2.6.28/090-increase_entropy_pools.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/090-increase_entropy_pools.patch
@ -0,0 +1,15 @@
+--- a/drivers/char/random.c
+++ b/drivers/char/random.c
+@@ -259,9 +259,9 @@
+ /*
+  * Configuration information
+  */
+-#define INPUT_POOL_WORDS 128
+-#define OUTPUT_POOL_WORDS 32
+-#define SEC_XFER_SIZE 512
+#define INPUT_POOL_WORDS 256
+#define OUTPUT_POOL_WORDS 64
+#define SEC_XFER_SIZE 1024
+ 
+ /*
+  * The minimum number of bits of entropy before we wake up a read on
--- a/target/linux/ixp4xx/patches-2.6.28/100-wg302v2_gateway7001_mac_plat_info.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/100-wg302v2_gateway7001_mac_plat_info.patch
@ -0,0 +1,68 @@
+--- a/arch/arm/mach-ixp4xx/gateway7001-setup.c
+++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c
+@@ -76,9 +76,35 @@ static struct platform_device gateway700
+ 	.resource	= &gateway7001_uart_resource,
+ };
+ 
+static struct eth_plat_info gateway7001_plat_eth[] = {
+	{
+		.phy		= 1,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	}, {
+		.phy		= 2,
+		.rxq		= 4,
+		.txreadyq	= 21,
+	}
+};
+
+static struct platform_device gateway7001_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= gateway7001_plat_eth,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= gateway7001_plat_eth + 1,
+	}
+};
+
+ static struct platform_device *gateway7001_devices[] __initdata = {
+ 	&gateway7001_flash,
+-	&gateway7001_uart
+	&gateway7001_uart,
+	&gateway7001_eth[0],
+	&gateway7001_eth[1],
+ };
+ 
+ static void __init gateway7001_init(void)
+--- a/arch/arm/mach-ixp4xx/wg302v2-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c
+@@ -77,9 +77,26 @@ static struct platform_device wg302v2_ua
+ 	.resource	= &wg302v2_uart_resource,
+ };
+ 
+static struct eth_plat_info wg302v2_plat_eth[] = {
+	{
+		.phy		= 8,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	}
+};
+
+static struct platform_device wg302v2_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= wg302v2_plat_eth,
+	}
+};
+
+ static struct platform_device *wg302v2_devices[] __initdata = {
+ 	&wg302v2_flash,
+ 	&wg302v2_uart,
+	&wg302v2_eth[0],
+ };
+ 
+ static void __init wg302v2_init(void)
--- a/target/linux/ixp4xx/patches-2.6.28/105-wg302v1_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/105-wg302v1_support.patch
@ -0,0 +1,257 @@
+--- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig
+@@ -155,6 +155,7 @@ CONFIG_MACH_AVILA=y
+ CONFIG_MACH_LOFT=y
+ CONFIG_ARCH_ADI_COYOTE=y
+ CONFIG_MACH_GATEWAY7001=y
+CONFIG_MACH_WG302V1=y
+ CONFIG_MACH_WG302V2=y
+ CONFIG_ARCH_IXDP425=y
+ CONFIG_MACH_IXDPG425=y
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -49,6 +49,14 @@ config MACH_GATEWAY7001
+ 	  7001 Access Point. For more information on this platform,
+ 	  see http://openwrt.org
+ 
+config MACH_WG302V1
+	bool "Netgear WG302 v1 / WAG302 v1"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support Netgear's
+	  WG302 v1 or WAG302 v1 Access Points. For more information
+	  on this platform, see http://openwrt.org
+
+ config MACH_WG302V2
+ 	bool "Netgear WG302 v2 / WAG302 v2"
+ 	select PCI
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -14,6 +14,7 @@ obj-pci-$(CONFIG_MACH_NSLU2)		+= nslu2-p
+ obj-pci-$(CONFIG_MACH_NAS100D)		+= nas100d-pci.o
+ obj-pci-$(CONFIG_MACH_DSMG600)		+= dsmg600-pci.o
+ obj-pci-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-pci.o
+obj-pci-$(CONFIG_MACH_WG302V1)		+= wg302v1-pci.o
+ obj-pci-$(CONFIG_MACH_WG302V2)		+= wg302v2-pci.o
+ obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+ 
+@@ -28,6 +29,7 @@ obj-$(CONFIG_MACH_NSLU2)	+= nslu2-setup.
+ obj-$(CONFIG_MACH_NAS100D)	+= nas100d-setup.o
+ obj-$(CONFIG_MACH_DSMG600)      += dsmg600-setup.o
+ obj-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-setup.o
+obj-$(CONFIG_MACH_WG302V1)	+= wg302v1-setup.o
+ obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-setup.o
+ obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
+ 
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wg302v1-pci.c
+@@ -0,0 +1,64 @@
+/*
+ * arch/arch/mach-ixp4xx/wg302v1-pci.c
+ *
+ * PCI setup routines for the Netgear WG302 v1 and WAG302 v1
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ *	Copyright (C) 2002 Jungo Software Technologies.
+ *	Copyright (C) 2003 MontaVista Software, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+
+#include <asm/mach/pci.h>
+
+void __init wg302v1_pci_preinit(void)
+{
+	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW);
+
+	ixp4xx_pci_preinit();
+}
+
+static int __init wg302v1_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot == 1)
+		return IRQ_IXP4XX_GPIO8;
+	else if (slot == 2)
+		return IRQ_IXP4XX_GPIO10;
+	else
+		return -1;
+}
+
+struct hw_pci wg302v1_pci __initdata = {
+	.nr_controllers = 1,
+	.preinit =        wg302v1_pci_preinit,
+	.swizzle =        pci_std_swizzle,
+	.setup =          ixp4xx_setup,
+	.scan =           ixp4xx_scan_bus,
+	.map_irq =        wg302v1_map_irq,
+};
+
+int __init wg302v1_pci_init(void)
+{
+	if (machine_is_wg302v1())
+		pci_common_init(&wg302v1_pci);
+	return 0;
+}
+
+subsys_initcall(wg302v1_pci_init);
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
+@@ -0,0 +1,142 @@
+/*
+ * arch/arm/mach-ixp4xx/wg302v1-setup.c
+ *
+ * Board setup for the Netgear WG302 v1 and WAG302 v1
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <kaloz@openwrt.org>
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/memory.h>
+
+#include <asm/setup.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data wg302v1_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource wg302v1_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device wg302v1_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &wg302v1_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &wg302v1_flash_resource,
+};
+
+static struct resource wg302v1_uart_resources[] = {
+	{
+		.start	= IXP4XX_UART1_BASE_PHYS,
+		.end	= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= IXP4XX_UART2_BASE_PHYS,
+		.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct plat_serial8250_port wg302v1_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device wg302v1_uart = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= wg302v1_uart_data,
+	},
+	.num_resources	= 2,
+	.resource	= wg302v1_uart_resources,
+};
+
+static struct eth_plat_info wg302v1_plat_eth[] = {
+	{
+		.phy		= 30,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	}
+};
+
+static struct platform_device wg302v1_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= wg302v1_plat_eth,
+	}
+};
+
+static struct platform_device *wg302v1_devices[] __initdata = {
+	&wg302v1_flash,
+	&wg302v1_uart,
+	&wg302v1_eth[0],
+};
+
+static void __init wg302v1_init(void)
+{
+	ixp4xx_sys_init();
+
+	wg302v1_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	wg302v1_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+	platform_add_devices(wg302v1_devices, ARRAY_SIZE(wg302v1_devices));
+}
+
+#ifdef CONFIG_MACH_WG302V1
+MACHINE_START(WG302V1, "Netgear WG302 v1 / WAG302 v1")
+	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= wg302v1_init,
+MACHINE_END
+#endif
--- a/target/linux/ixp4xx/patches-2.6.28/110-pronghorn_series_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/110-pronghorn_series_support.patch
@ -0,0 +1,387 @@
+--- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig
+@@ -157,6 +157,8 @@ CONFIG_ARCH_ADI_COYOTE=y
+ CONFIG_MACH_GATEWAY7001=y
+ CONFIG_MACH_WG302V1=y
+ CONFIG_MACH_WG302V2=y
+CONFIG_MACH_PRONGHORN=y
+CONFIG_MACH_PRONGHORNMETRO=y
+ CONFIG_ARCH_IXDP425=y
+ CONFIG_MACH_IXDPG425=y
+ CONFIG_MACH_IXDP465=y
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -65,6 +65,22 @@ config MACH_WG302V2
+ 	  WG302 v2 or WAG302 v2 Access Points. For more information
+ 	  on this platform, see http://openwrt.org
+ 
+config MACH_PRONGHORN
+	bool "ADI Pronghorn series"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support the ADI 
+	  Engineering Pronghorn series. For more
+	  information on this platform, see http://www.adiengineering.com
+
+#
+# There're only minimal differences kernel-wise between the Pronghorn and
+# Pronghorn Metro boards - they use different chip selects to drive the
+# CF slot connected to the expansion bus, so we just enable them together.
+#
+config MACH_PRONGHORNMETRO
+	def_bool MACH_PRONGHORN
+
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -17,6 +17,7 @@ obj-pci-$(CONFIG_MACH_GATEWAY7001)	+= ga
+ obj-pci-$(CONFIG_MACH_WG302V1)		+= wg302v1-pci.o
+ obj-pci-$(CONFIG_MACH_WG302V2)		+= wg302v2-pci.o
+ obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -32,6 +33,7 @@ obj-$(CONFIG_MACH_GATEWAY7001)	+= gatewa
+ obj-$(CONFIG_MACH_WG302V1)	+= wg302v1-setup.o
+ obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-setup.o
+ obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
+obj-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/pronghorn-pci.c
+@@ -0,0 +1,70 @@
+/*
+ * arch/arch/mach-ixp4xx/pronghorn-pci.c
+ *
+ * PCI setup routines for ADI Engineering Pronghorn series
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ *	Copyright (C) 2002 Jungo Software Technologies.
+ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+
+#include <asm/mach/pci.h>
+
+void __init pronghorn_pci_preinit(void)
+{
+	set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_LEVEL_LOW);
+
+	ixp4xx_pci_preinit();
+}
+
+static int __init pronghorn_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot == 13)
+		return IRQ_IXP4XX_GPIO4;
+	else if (slot == 14)
+		return IRQ_IXP4XX_GPIO6;
+	else if (slot == 15)
+		return IRQ_IXP4XX_GPIO11;
+	else if (slot == 16)
+		return IRQ_IXP4XX_GPIO1;
+	else
+		return -1;
+}
+
+struct hw_pci pronghorn_pci __initdata = {
+	.nr_controllers	= 1,
+	.preinit	= pronghorn_pci_preinit,
+	.swizzle	= pci_std_swizzle,
+	.setup		= ixp4xx_setup,
+	.scan		= ixp4xx_scan_bus,
+	.map_irq	= pronghorn_map_irq,
+};
+
+int __init pronghorn_pci_init(void)
+{
+	if (machine_is_pronghorn() || machine_is_pronghorn_metro())
+		pci_common_init(&pronghorn_pci);
+	return 0;
+}
+
+subsys_initcall(pronghorn_pci_init);
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c
+@@ -0,0 +1,245 @@
+/*
+ * arch/arm/mach-ixp4xx/pronghorn-setup.c
+ *
+ * Board setup for the ADI Engineering Pronghorn series
+ *
+ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/memory.h>
+#include <linux/i2c-gpio.h>
+#include <linux/leds.h>
+
+#include <asm/setup.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data pronghorn_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource pronghorn_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device pronghorn_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &pronghorn_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &pronghorn_flash_resource,
+};
+
+static struct resource pronghorn_uart_resources [] = {
+	{
+		.start		= IXP4XX_UART1_BASE_PHYS,
+		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM
+	},
+	{
+		.start		= IXP4XX_UART2_BASE_PHYS,
+		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM
+	}
+};
+
+static struct plat_serial8250_port pronghorn_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device pronghorn_uart = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM,
+	.dev		= {
+		.platform_data	= pronghorn_uart_data,
+	},
+	.num_resources	= 2,
+	.resource	= pronghorn_uart_resources,
+};
+
+static struct i2c_gpio_platform_data pronghorn_i2c_gpio_data = {
+	.sda_pin	= 9,
+	.scl_pin	= 10,
+};
+
+static struct platform_device pronghorn_i2c_gpio = {
+	.name		= "i2c-gpio",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &pronghorn_i2c_gpio_data,
+	},
+};
+
+static struct gpio_led pronghorn_led_pin[] = {
+	{
+		.name		= "pronghorn:green:status",
+		.gpio		= 7,
+	}
+};
+
+static struct gpio_led_platform_data pronghorn_led_data = {
+	.num_leds		= 1,
+	.leds			= pronghorn_led_pin,
+};
+
+static struct platform_device pronghorn_led = {
+	.name			= "leds-gpio",
+	.id			= -1,
+	.dev.platform_data	= &pronghorn_led_data,
+};
+
+static struct resource pronghorn_pata_resources[] = {
+	{
+		.flags	= IORESOURCE_MEM
+	},
+	{
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.name	= "intrq",
+		.start	= IRQ_IXP4XX_GPIO0,
+		.end	= IRQ_IXP4XX_GPIO0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct ixp4xx_pata_data pronghorn_pata_data = {
+	.cs0_bits	= 0xbfff0043,
+	.cs1_bits	= 0xbfff0043,
+};
+
+static struct platform_device pronghorn_pata = {
+	.name			= "pata_ixp4xx_cf",
+	.id			= 0,
+	.dev.platform_data      = &pronghorn_pata_data,
+	.num_resources		= ARRAY_SIZE(pronghorn_pata_resources),
+	.resource		= pronghorn_pata_resources,
+};
+
+static struct eth_plat_info pronghorn_plat_eth[] = {
+	{
+		.phy		= 0,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	}, {
+		.phy		= 1,
+		.rxq		= 4,
+		.txreadyq	= 21,
+	}
+};
+
+static struct platform_device pronghorn_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= pronghorn_plat_eth,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= pronghorn_plat_eth + 1,
+	}
+};
+
+static struct platform_device *pronghorn_devices[] __initdata = {
+	&pronghorn_flash,
+	&pronghorn_uart,
+	&pronghorn_led,
+	&pronghorn_eth[0],
+	&pronghorn_eth[1],
+};
+
+static void __init pronghorn_init(void)
+{
+	ixp4xx_sys_init();
+
+	pronghorn_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	pronghorn_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+	platform_add_devices(pronghorn_devices, ARRAY_SIZE(pronghorn_devices));
+
+	if (machine_is_pronghorn()) {
+		pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(2);
+		pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(2);
+
+		pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(3);
+		pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(3);
+
+		pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS2;
+		pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS3;
+	} else {
+		pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(3);
+		pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(3);
+
+		pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(4);
+		pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(4);
+
+		pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS3;
+		pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS4;
+
+		platform_device_register(&pronghorn_i2c_gpio);
+	}
+
+	platform_device_register(&pronghorn_pata);
+}
+
+MACHINE_START(PRONGHORN, "ADI Engineering Pronghorn")
+	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= pronghorn_init,
+MACHINE_END
+
+MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro")
+	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= pronghorn_init,
+MACHINE_END
+--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+@@ -41,7 +41,8 @@ static __inline__ void __arch_decomp_set
+ 	 * Some boards are using UART2 as console
+ 	 */
+ 	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+-			 machine_is_gateway7001() || machine_is_wg302v2())
+			 machine_is_gateway7001() || machine_is_wg302v2() ||
+			 machine_is_pronghorn() || machine_is_pronghorn_metro())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
--- a/target/linux/ixp4xx/patches-2.6.28/111-pronghorn_swap_uarts.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/111-pronghorn_swap_uarts.patch
@ -0,0 +1,44 @@
+--- a/arch/arm/mach-ixp4xx/pronghorn-setup.c
+++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c
+@@ -51,31 +51,31 @@ static struct platform_device pronghorn_
+ 
+ static struct resource pronghorn_uart_resources [] = {
+ 	{
+-		.start		= IXP4XX_UART1_BASE_PHYS,
+-		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.start		= IXP4XX_UART2_BASE_PHYS,
+		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ 		.flags		= IORESOURCE_MEM
+ 	},
+ 	{
+-		.start		= IXP4XX_UART2_BASE_PHYS,
+-		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.start		= IXP4XX_UART1_BASE_PHYS,
+		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ 		.flags		= IORESOURCE_MEM
+ 	}
+ };
+ 
+ static struct plat_serial8250_port pronghorn_uart_data[] = {
+ 	{
+-		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+-		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+-		.irq		= IRQ_IXP4XX_UART1,
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+ 		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ 		.iotype		= UPIO_MEM,
+ 		.regshift	= 2,
+ 		.uartclk	= IXP4XX_UART_XTAL,
+ 	},
+ 	{
+-		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+-		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+-		.irq		= IRQ_IXP4XX_UART2,
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+ 		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ 		.iotype		= UPIO_MEM,
+ 		.regshift	= 2,
--- a/target/linux/ixp4xx/patches-2.6.28/115-sidewinder_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/115-sidewinder_support.patch
@ -0,0 +1,282 @@
+From 60bdaaaf3446b4237566c6e04855186fc7bd766b Mon Sep 17 00:00:00 2001
+From: Imre Kaloz <kaloz@openwrt.org>
+Date: Sun, 13 Jul 2008 22:46:45 +0200
+Subject: [PATCH] Add support for the ADI Sidewinder
+
+Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
+---
+ arch/arm/mach-ixp4xx/Kconfig            |   10 ++-
+ arch/arm/mach-ixp4xx/Makefile           |    2 +
+ arch/arm/mach-ixp4xx/sidewinder-pci.c   |   68 ++++++++++++++
+ arch/arm/mach-ixp4xx/sidewinder-setup.c |  151 +++++++++++++++++++++++++++++++
+ 4 files changed, 230 insertions(+), 1 deletions(-)
+ create mode 100644 arch/arm/mach-ixp4xx/sidewinder-pci.c
+ create mode 100644 arch/arm/mach-ixp4xx/sidewinder-setup.c
+
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -81,6 +81,14 @@ config MACH_PRONGHORN
+ config MACH_PRONGHORNMETRO
+ 	def_bool MACH_PRONGHORN
+ 
+config MACH_SIDEWINDER
+	bool "ADI Sidewinder"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support the ADI 
+	  Engineering Sidewinder board. For more information on this
+	  platform, see http://www.adiengineering.com
+
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+@@ -163,7 +171,7 @@ config MACH_FSG
+ #
+ config CPU_IXP46X
+ 	bool
+-	depends on MACH_IXDP465
+	depends on MACH_IXDP465 || MACH_SIDEWINDER
+ 	default y
+ 
+ config CPU_IXP43X
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -18,6 +18,7 @@ obj-pci-$(CONFIG_MACH_WG302V1)		+= wg302
+ obj-pci-$(CONFIG_MACH_WG302V2)		+= wg302v2-pci.o
+ obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+ obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-pci.o
+obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -34,6 +35,7 @@ obj-$(CONFIG_MACH_WG302V1)	+= wg302v1-se
+ obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-setup.o
+ obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
+ obj-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-setup.o
+obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/sidewinder-pci.c
+@@ -0,0 +1,68 @@
+/*
+ * arch/arch/mach-ixp4xx/pronghornmetro-pci.c
+ *
+ * PCI setup routines for ADI Engineering Sidewinder
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ *	Copyright (C) 2002 Jungo Software Technologies.
+ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+#include <asm/mach/pci.h>
+
+void __init sidewinder_pci_preinit(void)
+{
+	set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW);
+
+	ixp4xx_pci_preinit();
+}
+
+static int __init sidewinder_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot == 1)
+		return IRQ_IXP4XX_GPIO11;
+	else if (slot == 2)
+		return IRQ_IXP4XX_GPIO10;
+	else if (slot == 3)
+		return IRQ_IXP4XX_GPIO9;
+	else
+		return -1;
+}
+
+struct hw_pci sidewinder_pci __initdata = {
+	.nr_controllers	= 1,
+	.preinit	= sidewinder_pci_preinit,
+	.swizzle	= pci_std_swizzle,
+	.setup		= ixp4xx_setup,
+	.scan		= ixp4xx_scan_bus,
+	.map_irq	= sidewinder_map_irq,
+};
+
+int __init sidewinder_pci_init(void)
+{
+	if (machine_is_sidewinder())
+		pci_common_init(&sidewinder_pci);
+	return 0;
+}
+
+subsys_initcall(sidewinder_pci_init);
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/sidewinder-setup.c
+@@ -0,0 +1,149 @@
+/*
+ * arch/arm/mach-ixp4xx/sidewinder-setup.c
+ *
+ * Board setup for the ADI Engineering Sidewinder
+ *
+ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data sidewinder_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource sidewinder_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device sidewinder_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &sidewinder_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &sidewinder_flash_resource,
+};
+
+static struct resource sidewinder_uart_resources[] = {
+	{
+		.start	= IXP4XX_UART1_BASE_PHYS,
+		.end	= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= IXP4XX_UART2_BASE_PHYS,
+		.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct plat_serial8250_port sidewinder_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device sidewinder_uart = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM,
+	.dev		= {
+		.platform_data	= sidewinder_uart_data,
+	},
+	.num_resources	= ARRAY_SIZE(sidewinder_uart_resources),
+	.resource	= sidewinder_uart_resources,
+};
+
+static struct eth_plat_info sidewinder_plat_eth[] = {
+	{
+		.phy		= 5,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	}, {
+		.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
+		.phy_mask	= 0x1e,
+		.rxq		= 4,
+		.txreadyq	= 21,
+	}, {
+		.phy		= 31,
+		.rxq		= 2,
+		.txreadyq	= 19,
+	}
+};
+
+static struct platform_device sidewinder_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= sidewinder_plat_eth,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= sidewinder_plat_eth + 1,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEA,
+		.dev.platform_data	= sidewinder_plat_eth + 2,
+	}
+};
+
+static struct platform_device *sidewinder_devices[] __initdata = {
+	&sidewinder_flash,
+	&sidewinder_uart,
+	&sidewinder_eth[0],
+	&sidewinder_eth[1],
+	&sidewinder_eth[2],
+};
+
+static void __init sidewinder_init(void)
+{
+	ixp4xx_sys_init();
+
+	sidewinder_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	sidewinder_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_64M - 1;
+
+	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+	platform_add_devices(sidewinder_devices, ARRAY_SIZE(sidewinder_devices));
+}
+
+MACHINE_START(SIDEWINDER, "ADI Engineering Sidewinder")
+	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= sidewinder_init,
+MACHINE_END
--- a/target/linux/ixp4xx/patches-2.6.28/116-sidewinder_fis_location.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/116-sidewinder_fis_location.patch
@ -0,0 +1,30 @@
+--- a/drivers/mtd/redboot.c
+++ b/drivers/mtd/redboot.c
+@@ -13,6 +13,8 @@
+ 
+ #define BOARD_CONFIG_PART		"boardconfig"
+ 
+#include <asm/mach-types.h>
+
+ struct fis_image_desc {
+     unsigned char name[16];      // Null terminated name
+     uint32_t	  flash_base;    // Address within FLASH of image
+@@ -30,7 +32,8 @@ struct fis_list {
+ 	struct fis_list *next;
+ };
+ 
+-static int directory = CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK;
+int directory = CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK;
+
+ module_param(directory, int, 0);
+ 
+ static inline int redboot_checksum(struct fis_image_desc *img)
+@@ -59,6 +62,8 @@ static int parse_redboot_partitions(stru
+ #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
+ 	static char nullstring[] = "unallocated";
+ #endif
+	if (machine_is_sidewinder())
+		directory = -5;
+ 
+ 	if ( directory < 0 ) {
+ 		offset = master->size + directory * master->erasesize;
--- a/target/linux/ixp4xx/patches-2.6.28/120-compex_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/120-compex_support.patch
@ -0,0 +1,212 @@
+From 24025a2dcf1248079dd3019fac6ed955252d277f Mon Sep 17 00:00:00 2001
+From: Imre Kaloz <kaloz@openwrt.org>
+Date: Mon, 14 Jul 2008 21:56:34 +0200
+Subject: [PATCH] Add support for the Compex WP18 / NP18A boards
+
+Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
+---
+ arch/arm/mach-ixp4xx/Kconfig        |    8 ++
+ arch/arm/mach-ixp4xx/Makefile       |    2 +
+ arch/arm/mach-ixp4xx/compex-setup.c |  136 +++++++++++++++++++++++++++++++++++
+ arch/arm/mach-ixp4xx/ixdp425-pci.c  |    3 +-
+ arch/arm/tools/mach-types           |    2 +-
+ 5 files changed, 149 insertions(+), 2 deletions(-)
+ create mode 100644 arch/arm/mach-ixp4xx/compex-setup.c
+
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -89,6 +89,14 @@ config MACH_SIDEWINDER
+ 	  Engineering Sidewinder board. For more information on this
+ 	  platform, see http://www.adiengineering.com
+ 
+config MACH_COMPEX
+	bool "Compex WP18 / NP18A"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support Compex' 
+	  WP18 or NP18A boards. For more information on this
+	  platform, see http://www.compex.com.sg/home/OEM/product_ap.htm
+
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -19,6 +19,7 @@ obj-pci-$(CONFIG_MACH_WG302V2)		+= wg302
+ obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+ obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-pci.o
+ obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-pci.o
+obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp425-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -36,6 +37,7 @@ obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-se
+ obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
+ obj-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-setup.o
+ obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-setup.o
+obj-$(CONFIG_MACH_COMPEX)	+= compex-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/compex-setup.c
+@@ -0,0 +1,136 @@
+/*
+ * arch/arm/mach-ixp4xx/compex-setup.c
+ *
+ * Compex WP18 / NP18A board-setup
+ *
+ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ *	Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data compex_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource compex_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device compex_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &compex_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &compex_flash_resource,
+};
+
+static struct resource compex_uart_resources[] = {
+	{
+		.start		= IXP4XX_UART1_BASE_PHYS,
+		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM
+	},
+	{
+		.start		= IXP4XX_UART2_BASE_PHYS,
+		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM
+	}
+};
+
+static struct plat_serial8250_port compex_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device compex_uart = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev.platform_data	= compex_uart_data,
+	.num_resources		= 2,
+	.resource		= compex_uart_resources,
+};
+
+static struct eth_plat_info compex_plat_eth[] = {
+	{
+		.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
+		.phy_mask	= 0xf0000,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	}, {
+		.phy		= 3,
+		.rxq		= 4,
+		.txreadyq	= 21,
+	}
+};
+
+static struct platform_device compex_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= compex_plat_eth,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= compex_plat_eth + 1,
+	}
+};
+
+static struct platform_device *compex_devices[] __initdata = {
+	&compex_flash,
+	&compex_uart,
+	&compex_eth[0],
+	&compex_eth[1],
+};
+
+static void __init compex_init(void)
+{
+	ixp4xx_sys_init();
+
+	compex_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	compex_flash_resource.end =
+		IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+	platform_add_devices(compex_devices, ARRAY_SIZE(compex_devices));
+}
+
+MACHINE_START(COMPEX, "Compex WP18 / NP18A")
+	/* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= compex_init,
+MACHINE_END
+--- a/arch/arm/mach-ixp4xx/ixdp425-pci.c
+++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c
+@@ -66,7 +66,8 @@ struct hw_pci ixdp425_pci __initdata = {
+ int __init ixdp425_pci_init(void)
+ {
+ 	if (machine_is_ixdp425() || machine_is_ixcdp1100() ||
+-			machine_is_ixdp465() || machine_is_kixrp435())
+			machine_is_ixdp465() || machine_is_kixrp435() ||
+			machine_is_compex())
+ 		pci_common_init(&ixdp425_pci);
+ 	return 0;
+ }
+--- a/arch/arm/tools/mach-types
+++ b/arch/arm/tools/mach-types
+@@ -1273,7 +1273,7 @@ oiab			MACH_OIAB		OIAB			1269
+ smdk6400		MACH_SMDK6400		SMDK6400		1270
+ nokia_n800		MACH_NOKIA_N800		NOKIA_N800		1271
+ greenphone		MACH_GREENPHONE		GREENPHONE		1272
+-compex42x		MACH_COMPEXWP18		COMPEXWP18		1273
+compex			MACH_COMPEX		COMPEX			1273
+ xmate			MACH_XMATE		XMATE			1274
+ energizer		MACH_ENERGIZER		ENERGIZER		1275
+ ime1			MACH_IME1		IME1			1276
--- a/target/linux/ixp4xx/patches-2.6.28/130-wrt300nv2_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/130-wrt300nv2_support.patch
@ -0,0 +1,225 @@
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -97,6 +97,14 @@ config MACH_COMPEX
+ 	  WP18 or NP18A boards. For more information on this
+ 	  platform, see http://www.compex.com.sg/home/OEM/product_ap.htm
+ 
+config MACH_WRT300NV2
+	bool "Linksys WRT300N v2"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support Linksys' 
+	  WRT300N v2 router. For more information on this
+	  platform, see http://openwrt.org
+
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -20,6 +20,7 @@ obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+ obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-pci.o
+ obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-pci.o
+ obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp425-pci.o
+obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt300nv2-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -38,6 +39,7 @@ obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
+ obj-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-setup.o
+ obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-setup.o
+ obj-$(CONFIG_MACH_COMPEX)	+= compex-setup.o
+obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv2-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wrt300nv2-pci.c
+@@ -0,0 +1,65 @@
+/*
+ * arch/arch/mach-ixp4xx/wrt300nv2-pci.c
+ *
+ * PCI setup routines for Linksys WRT300N v2
+ *
+ * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ *	Copyright (C) 2002 Jungo Software Technologies.
+ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+#include <asm/mach/pci.h>
+
+extern void ixp4xx_pci_preinit(void);
+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
+
+void __init wrt300nv2_pci_preinit(void)
+{
+	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
+
+	ixp4xx_pci_preinit();
+}
+
+static int __init wrt300nv2_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot == 1)
+		return IRQ_IXP4XX_GPIO8;
+	else return -1;
+}
+
+struct hw_pci wrt300nv2_pci __initdata = {
+	.nr_controllers = 1,
+	.preinit =        wrt300nv2_pci_preinit,
+	.swizzle =        pci_std_swizzle,
+	.setup =          ixp4xx_setup,
+	.scan =           ixp4xx_scan_bus,
+	.map_irq =        wrt300nv2_map_irq,
+};
+
+int __init wrt300nv2_pci_init(void)
+{
+	if (machine_is_wrt300nv2())
+		pci_common_init(&wrt300nv2_pci);
+	return 0;
+}
+
+subsys_initcall(wrt300nv2_pci_init);
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+@@ -0,0 +1,108 @@
+/*
+ * arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+ *
+ * Board setup for the Linksys WRT300N v2
+ *
+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data wrt300nv2_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource wrt300nv2_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device wrt300nv2_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &wrt300nv2_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &wrt300nv2_flash_resource,
+};
+
+static struct resource wrt300nv2_uart_resource = {
+	.start	= IXP4XX_UART2_BASE_PHYS,
+	.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct plat_serial8250_port wrt300nv2_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device wrt300nv2_uart = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= wrt300nv2_uart_data,
+	},
+	.num_resources	= 1,
+	.resource	= &wrt300nv2_uart_resource,
+};
+
+static struct platform_device *wrt300nv2_devices[] __initdata = {
+	&wrt300nv2_flash,
+	&wrt300nv2_uart
+};
+
+static void __init wrt300nv2_init(void)
+{
+	ixp4xx_sys_init();
+
+	wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	wrt300nv2_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+	platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices));
+}
+
+#ifdef CONFIG_MACH_WRT300NV2
+MACHINE_START(WRT300NV2, "Linksys WRT300N v2")
+	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= wrt300nv2_init,
+MACHINE_END
+#endif
+--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+@@ -42,7 +42,7 @@ static __inline__ void __arch_decomp_set
+ 	 */
+ 	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+ 			 machine_is_gateway7001() || machine_is_wg302v2() ||
+-			 machine_is_pronghorn() || machine_is_pronghorn_metro())
+			 machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
--- a/target/linux/ixp4xx/patches-2.6.28/131-wrt300nv2_mac_plat_info.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/131-wrt300nv2_mac_plat_info.patch
@ -0,0 +1,40 @@
+--- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+@@ -76,9 +76,36 @@ static struct platform_device wrt300nv2_
+ 	.resource	= &wrt300nv2_uart_resource,
+ };
+ 
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info wrt300nv2_plat_eth[] = {
+	{
+		.phy		= -1,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	}, {
+		.phy		= 1,
+		.rxq		= 4,
+		.txreadyq	= 21,
+	}
+};
+
+static struct platform_device wrt300nv2_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= wrt300nv2_plat_eth,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= wrt300nv2_plat_eth + 1,
+	}
+};
+
+ static struct platform_device *wrt300nv2_devices[] __initdata = {
+ 	&wrt300nv2_flash,
+-	&wrt300nv2_uart
+	&wrt300nv2_uart,
+	&wrt300nv2_eth[0],
+	&wrt300nv2_eth[1],
+ };
+ 
+ static void __init wrt300nv2_init(void)
--- a/target/linux/ixp4xx/patches-2.6.28/150-lanready_ap1000_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/150-lanready_ap1000_support.patch
@ -0,0 +1,200 @@
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/ap1000-setup.c
+@@ -0,0 +1,151 @@
+/*
+ * arch/arm/mach-ixp4xx/ap1000-setup.c
+ *
+ * Lanready AP-1000
+ *
+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on ixdp425-setup.c:
+ *	Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data ap1000_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource ap1000_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device ap1000_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &ap1000_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &ap1000_flash_resource,
+};
+
+static struct resource ap1000_uart_resources[] = {
+	{
+		.start		= IXP4XX_UART1_BASE_PHYS,
+		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM
+	},
+	{
+		.start		= IXP4XX_UART2_BASE_PHYS,
+		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM
+	}
+};
+
+static struct plat_serial8250_port ap1000_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device ap1000_uart = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev.platform_data	= ap1000_uart_data,
+	.num_resources		= 2,
+	.resource		= ap1000_uart_resources
+};
+
+static struct platform_device *ap1000_devices[] __initdata = {
+	&ap1000_flash,
+	&ap1000_uart
+};
+
+static char ap1000_mem_fixup[] __initdata = "mem=64M ";
+
+static void __init ap1000_fixup(struct machine_desc *desc,
+		struct tag *tags, char **cmdline, struct meminfo *mi)
+
+{
+	struct tag *t = tags;
+	char *p = *cmdline;
+
+	/* Find the end of the tags table, taking note of any cmdline tag. */
+	for (; t->hdr.size; t = tag_next(t)) {
+		if (t->hdr.tag == ATAG_CMDLINE) {
+			p = t->u.cmdline.cmdline;
+		}
+	}
+
+	/* Overwrite the end of the table with a new cmdline tag. */
+	t->hdr.tag = ATAG_CMDLINE;
+	t->hdr.size = (sizeof (struct tag_header) +
+		strlen(ap1000_mem_fixup) + strlen(p) + 1 + 4) >> 2;
+	strlcpy(t->u.cmdline.cmdline, ap1000_mem_fixup, COMMAND_LINE_SIZE);
+	strlcpy(t->u.cmdline.cmdline + strlen(ap1000_mem_fixup), p,
+		COMMAND_LINE_SIZE - strlen(ap1000_mem_fixup));
+
+	/* Terminate the table. */
+	t = tag_next(t);
+	t->hdr.tag = ATAG_NONE;
+	t->hdr.size = 0;
+}
+
+static void __init ap1000_init(void)
+{
+	ixp4xx_sys_init();
+
+	ap1000_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	ap1000_flash_resource.end =
+		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
+
+	platform_add_devices(ap1000_devices, ARRAY_SIZE(ap1000_devices));
+}
+
+#ifdef CONFIG_MACH_AP1000
+MACHINE_START(AP1000, "Lanready AP-1000")
+	/* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.fixup		= ap1000_fixup,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= ap1000_init,
+MACHINE_END
+#endif
+--- a/arch/arm/mach-ixp4xx/ixdp425-pci.c
+++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c
+@@ -67,7 +67,7 @@ int __init ixdp425_pci_init(void)
+ {
+ 	if (machine_is_ixdp425() || machine_is_ixcdp1100() ||
+ 			machine_is_ixdp465() || machine_is_kixrp435() ||
+-			machine_is_compex())
+			machine_is_compex() || machine_is_ap1000())
+ 		pci_common_init(&ixdp425_pci);
+ 	return 0;
+ }
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -105,6 +105,14 @@ config MACH_WRT300NV2
+ 	  WRT300N v2 router. For more information on this
+ 	  platform, see http://openwrt.org
+ 
+config MACH_AP1000
+	bool "Lanready AP-1000"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support Lanready's
+	  AP1000 board. For more information on this
+	  platform, see http://openwrt.org
+
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -21,6 +21,7 @@ obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pron
+ obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-pci.o
+ obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt300nv2-pci.o
+obj-pci-$(CONFIG_MACH_AP1000)		+= ixdp425-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -40,6 +41,7 @@ obj-$(CONFIG_MACH_PRONGHORN)	+= pronghor
+ obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-setup.o
+ obj-$(CONFIG_MACH_COMPEX)	+= compex-setup.o
+ obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv2-setup.o
+obj-$(CONFIG_MACH_AP1000)	+= ap1000-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
--- a/target/linux/ixp4xx/patches-2.6.28/151-lanready_ap1000_mac_plat_info.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/151-lanready_ap1000_mac_plat_info.patch
@ -0,0 +1,41 @@
+--- a/arch/arm/mach-ixp4xx/ap1000-setup.c
+++ b/arch/arm/mach-ixp4xx/ap1000-setup.c
+@@ -90,9 +90,37 @@ static struct platform_device ap1000_uar
+ 	.resource		= ap1000_uart_resources
+ };
+ 
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info ap1000_plat_eth[] = {
+	{
+		.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
+		.phy_mask	= 0x1e,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	}, {
+		.phy		= 5,
+		.rxq		= 4,
+		.txreadyq	= 21,
+	}
+};
+
+static struct platform_device ap1000_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= ap1000_plat_eth,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= ap1000_plat_eth + 1,
+	}
+};
+
+ static struct platform_device *ap1000_devices[] __initdata = {
+ 	&ap1000_flash,
+-	&ap1000_uart
+	&ap1000_uart,
+	&ap1000_eth[0],
+	&ap1000_eth[1],
+ };
+ 
+ static char ap1000_mem_fixup[] __initdata = "mem=64M ";
--- a/target/linux/ixp4xx/patches-2.6.28/162-wg302v1_mem_fixup.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/162-wg302v1_mem_fixup.patch
@ -0,0 +1,47 @@
+--- a/arch/arm/mach-ixp4xx/wg302v1-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
+@@ -115,6 +115,36 @@ static struct platform_device *wg302v1_d
+ 	&wg302v1_eth[0],
+ };
+ 
+static char wg302v1_mem_fixup[] __initdata = "mem=32M ";
+
+static void __init wg302v1_fixup(struct machine_desc *desc,
+		struct tag *tags, char **cmdline, struct meminfo *mi)
+
+{
+	struct tag *t = tags;
+	char *p = *cmdline;
+
+	/* Find the end of the tags table, taking note of any cmdline tag. */
+	for (; t->hdr.size; t = tag_next(t)) {
+		if (t->hdr.tag == ATAG_CMDLINE) {
+			p = t->u.cmdline.cmdline;
+		}
+	}
+
+	/* Overwrite the end of the table with a new cmdline tag. */
+	t->hdr.tag = ATAG_CMDLINE;
+	t->hdr.size = (sizeof (struct tag_header) +
+		strlen(wg302v1_mem_fixup) + strlen(p) + 1 + 4) >> 2;
+	strlcpy(t->u.cmdline.cmdline, wg302v1_mem_fixup, COMMAND_LINE_SIZE);
+	strlcpy(t->u.cmdline.cmdline + strlen(wg302v1_mem_fixup), p,
+		COMMAND_LINE_SIZE - strlen(wg302v1_mem_fixup));
+
+	/* Terminate the table. */
+	t = tag_next(t);
+	t->hdr.tag = ATAG_NONE;
+	t->hdr.size = 0;
+}
+
+ static void __init wg302v1_init(void)
+ {
+ 	ixp4xx_sys_init();
+@@ -133,6 +163,7 @@ MACHINE_START(WG302V1, "Netgear WG302 v1
+ 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ 	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+ 	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.fixup		= wg302v1_fixup,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
--- a/target/linux/ixp4xx/patches-2.6.28/170-ixdpg425_mac_plat_info.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/170-ixdpg425_mac_plat_info.patch
@ -0,0 +1,41 @@
+--- a/arch/arm/mach-ixp4xx/coyote-setup.c
+++ b/arch/arm/mach-ixp4xx/coyote-setup.c
+@@ -73,9 +73,37 @@ static struct platform_device coyote_uar
+ 	.resource	= &coyote_uart_resource,
+ };
+ 
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info ixdpg425_plat_eth[] = {
+        {
+                .phy            = 5,
+                .rxq            = 3,
+                .txreadyq       = 20,
+        }, {
+                .phy            = 4,
+                .rxq            = 4,
+                .txreadyq       = 21,
+        }
+};
+
+static struct platform_device ixdpg425_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= ixdpg425_plat_eth,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= ixdpg425_plat_eth + 1,
+	}
+};
+
+
+ static struct platform_device *coyote_devices[] __initdata = {
+ 	&coyote_flash,
+-	&coyote_uart
+	&coyote_uart,
+	&ixdpg425_eth[0],
+	&ixdpg425_eth[1],
+ };
+ 
+ static void __init coyote_init(void)
--- a/target/linux/ixp4xx/patches-2.6.28/180-tw5334_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/180-tw5334_support.patch
@ -0,0 +1,284 @@
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -158,6 +158,14 @@ config ARCH_PRPMC1100
+ 	  PrPCM1100 Processor Mezanine Module. For more information on
+ 	  this platform, see <file:Documentation/arm/IXP4xx>.
+ 
+config MACH_TW5334
+	bool "Titan Wireless TW-533-4"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support the Titan
+	  Wireless TW533-4. For more information on this platform,
+	  see http://openwrt.org
+
+ config MACH_NAS100D
+ 	bool
+ 	prompt "NAS100D"
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -22,6 +22,7 @@ obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sid
+ obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt300nv2-pci.o
+ obj-pci-$(CONFIG_MACH_AP1000)		+= ixdp425-pci.o
+obj-pci-$(CONFIG_MACH_TW5334)		+= tw5334-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -42,6 +43,7 @@ obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewin
+ obj-$(CONFIG_MACH_COMPEX)	+= compex-setup.o
+ obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv2-setup.o
+ obj-$(CONFIG_MACH_AP1000)	+= ap1000-setup.o
+obj-$(CONFIG_MACH_TW5334)	+= tw5334-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/tw5334-setup.c
+@@ -0,0 +1,162 @@
+/*
+ * arch/arm/mach-ixp4xx/tw5334-setup.c
+ *
+ * Board setup for the Titan Wireless TW-533-4
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/if_ether.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data tw5334_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource tw5334_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device tw5334_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &tw5334_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &tw5334_flash_resource,
+};
+
+static struct resource tw5334_uart_resource = {
+	.start	= IXP4XX_UART2_BASE_PHYS,
+	.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct plat_serial8250_port tw5334_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device tw5334_uart = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= tw5334_uart_data,
+	},
+	.num_resources	= 1,
+	.resource	= &tw5334_uart_resource,
+};
+
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info tw5334_plat_eth[] = {
+        {
+                .phy            = 0,
+                .rxq            = 3,
+		.txreadyq	= 20,
+        }, {
+                .phy            = 1,
+                .rxq            = 4,
+		.txreadyq	= 21,
+	}
+};
+
+static struct platform_device tw5334_eth[] = {
+        {
+                .name                   = "ixp4xx_eth",
+                .id                     = IXP4XX_ETH_NPEB,
+                .dev.platform_data      = tw5334_plat_eth,
+        }, {
+                .name                   = "ixp4xx_eth",
+                .id                     = IXP4XX_ETH_NPEC,
+                .dev.platform_data      = tw5334_plat_eth + 1,
+	}
+};
+
+static struct platform_device *tw5334_devices[] __initdata = {
+	&tw5334_flash,
+	&tw5334_uart,
+	&tw5334_eth[0],
+	&tw5334_eth[1],
+};
+
+static void __init tw5334_init(void)
+{
+	DECLARE_MAC_BUF(mac_buf);
+	uint8_t __iomem *f;
+	int i;
+
+	ixp4xx_sys_init();
+
+	tw5334_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	tw5334_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+	platform_add_devices(tw5334_devices, ARRAY_SIZE(tw5334_devices));
+
+	/*
+	 * Map in a portion of the flash and read the MAC addresses.
+	 * Since it is stored in BE in the flash itself, we need to
+	 * byteswap it if we're in LE mode.
+	 */
+	f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x1000000);
+	if (f) {
+		for (i = 0; i < 6; i++)
+#ifdef __ARMEB__
+		tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + i);
+		tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + i);
+#else
+		tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + (i^3));
+		tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + (i^3));
+#endif
+		iounmap(f);
+	}
+	printk(KERN_INFO "TW-533-4: Using MAC address %s for port 0\n",
+		print_mac(mac_buf, tw5334_plat_eth[0].hwaddr));
+	printk(KERN_INFO "TW-533-4: Using MAC address %s for port 1\n",
+		print_mac(mac_buf, tw5334_plat_eth[1].hwaddr));
+}
+
+#ifdef CONFIG_MACH_TW5334
+MACHINE_START(TW5334, "Titan Wireless TW-533-4")
+	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= tw5334_init,
+MACHINE_END
+#endif
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/tw5334-pci.c
+@@ -0,0 +1,69 @@
+/*
+ * arch/arch/mach-ixp4xx/tw5334-pci.c
+ *
+ * PCI setup routines for the Titan Wireless TW-533-4
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ *	Copyright (C) 2002 Jungo Software Technologies.
+ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+
+#include <asm/mach/pci.h>
+
+void __init tw5334_pci_preinit(void)
+{
+	set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO2, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO0, IRQ_TYPE_LEVEL_LOW);
+
+	ixp4xx_pci_preinit();
+}
+
+static int __init tw5334_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot == 12)
+		return IRQ_IXP4XX_GPIO6;
+	else if (slot == 13)
+		return IRQ_IXP4XX_GPIO2;
+	else if (slot == 14)
+		return IRQ_IXP4XX_GPIO1;
+	else if (slot == 15)
+		return IRQ_IXP4XX_GPIO0;
+	else return -1;
+}
+
+struct hw_pci tw5334_pci __initdata = {
+	.nr_controllers = 1,
+	.preinit =        tw5334_pci_preinit,
+	.swizzle =        pci_std_swizzle,
+	.setup =          ixp4xx_setup,
+	.scan =           ixp4xx_scan_bus,
+	.map_irq =        tw5334_map_irq,
+};
+
+int __init tw5334_pci_init(void)
+{
+	if (machine_is_tw5334())
+		pci_common_init(&tw5334_pci);
+	return 0;
+}
+
+subsys_initcall(tw5334_pci_init);
+--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+@@ -42,7 +42,8 @@ static __inline__ void __arch_decomp_set
+ 	 */
+ 	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+ 			 machine_is_gateway7001() || machine_is_wg302v2() ||
+-			 machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2())
+			 machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
+			 machine_is_tw5334())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
--- a/target/linux/ixp4xx/patches-2.6.28/185-mi424wr_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/185-mi424wr_support.patch
@ -0,0 +1,465 @@
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/mi424wr-pci.c
+@@ -0,0 +1,71 @@
+/*
+ * arch/arm/mach-ixp4xx/mi424wr-pci.c
+ *
+ * Actiontec MI424WR board-level PCI initialization
+ *
+ * Copyright (C) 2008 Jose Vasconcellos
+ *
+ * Maintainer: Jose Vasconcellos <jvasco@verizon.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/pci.h>
+
+/* PCI controller GPIO to IRQ pin mappings
+ * This information was obtained from Actiontec's GPL release.
+ *
+ *		INTA		INTB
+ * SLOT 13	8		6
+ * SLOT 14	7		8
+ * SLOT 15	6		7
+ */
+
+void __init mi424wr_pci_preinit(void)
+{
+	set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO7, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
+
+	ixp4xx_pci_preinit();
+}
+
+static int __init mi424wr_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot == 13)
+		return IRQ_IXP4XX_GPIO8;
+	if (slot == 14)
+		return IRQ_IXP4XX_GPIO7;
+	if (slot == 15)
+		return IRQ_IXP4XX_GPIO6;
+
+	return -1;
+}
+
+struct hw_pci mi424wr_pci __initdata = {
+	.nr_controllers = 1,
+	.preinit	= mi424wr_pci_preinit,
+	.swizzle	= pci_std_swizzle,
+	.setup		= ixp4xx_setup,
+	.scan		= ixp4xx_scan_bus,
+	.map_irq	= mi424wr_map_irq,
+};
+
+int __init mi424wr_pci_init(void)
+{
+	if (machine_is_mi424wr())
+		pci_common_init(&mi424wr_pci);
+	return 0;
+}
+
+subsys_initcall(mi424wr_pci_init);
+
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/mi424wr-setup.c
+@@ -0,0 +1,344 @@
+/*
+ * arch/arm/mach-ixp4xx/mi424wr-setup.c
+ *
+ * Actiontec MI424-WR board setup
+ * Copyright (c) 2008 Jose Vasconcellos
+ *
+ * Based on Gemtek GTWX5715 by
+ * Copyright (C) 2004 George T. Joseph
+ * Derived from Coyote
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/types.h>
+#include <linux/memory.h>
+#include <linux/leds.h>
+#include <linux/spi/spi_gpio.h>
+
+#include <asm/setup.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+/*
+ * GPIO 2,3,4 and 9 are hard wired to the Micrel/Kendin KS8995M Switch
+ * and operate as an SPI type interface.  The details of the interface
+ * are available on Kendin/Micrel's web site.
+ */
+
+#define MI424WR_KSSPI_SELECT		9
+#define MI424WR_KSSPI_TXD		4
+#define MI424WR_KSSPI_CLOCK		2
+#define MI424WR_KSSPI_RXD		3
+
+/*
+ * The "reset" button is wired to GPIO 10.
+ * The GPIO is brought "low" when the button is pushed.
+ */
+
+#define MI424WR_BUTTON_GPIO	10
+#define MI424WR_BUTTON_IRQ	IRQ_IXP4XX_GPIO10
+
+#define MI424WR_MOCA_WAN_LED	11
+
+/* Latch on CS1 - taken from Actiontec's 2.4 source code
+ * 
+ * default latch value
+ * 0  - power alarm led (red)           0 (off)
+ * 1  - power led (green)               0 (off)
+ * 2  - wireless led    (green)         1 (off)
+ * 3  - no internet led (red)           0 (off)
+ * 4  - internet ok led (green)         0 (off)
+ * 5  - moca LAN                        0 (off)
+ * 6  - WAN alarm led (red)		0 (off)
+ * 7  - PCI reset                       1 (not reset)
+ * 8  - IP phone 1 led (green)          1 (off)
+ * 9  - IP phone 2 led (green)          1 (off)
+ * 10 - VOIP ready led (green)          1 (off)
+ * 11 - PSTN relay 1 control            0 (PSTN)
+ * 12 - PSTN relay 1 control            0 (PSTN)
+ * 13 - N/A
+ * 14 - N/A
+ * 15 - N/A
+ */
+
+#define MI424WR_LATCH_MASK              0x04
+#define MI424WR_LATCH_DEFAULT           0x1f86
+
+#define MI424WR_LATCH_ALARM_LED         0x00
+#define MI424WR_LATCH_POWER_LED         0x01
+#define MI424WR_LATCH_WIRELESS_LED      0x02
+#define MI424WR_LATCH_INET_DOWN_LED     0x03
+#define MI424WR_LATCH_INET_OK_LED       0x04
+#define MI424WR_LATCH_MOCA_LAN_LED      0x05
+#define MI424WR_LATCH_WAN_ALARM_LED     0x06
+#define MI424WR_LATCH_PCI_RESET         0x07
+#define MI424WR_LATCH_PHONE1_LED        0x08
+#define MI424WR_LATCH_PHONE2_LED        0x09
+#define MI424WR_LATCH_VOIP_LED          0x10
+#define MI424WR_LATCH_PSTN_RELAY1       0x11
+#define MI424WR_LATCH_PSTN_RELAY2       0x12
+
+/* initialize CS1 to default timings, Intel style, 16-bit bus */
+#define MI424WR_CS1_CONFIG	0x80000002
+
+/* Define both UARTs but they are not easily accessible.
+ */
+
+static struct resource mi424wr_uart_resources[] = {
+	{
+		.start	= IXP4XX_UART1_BASE_PHYS,
+		.end	= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= IXP4XX_UART2_BASE_PHYS,
+		.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+
+static struct plat_serial8250_port mi424wr_uart_platform_data[] = {
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device mi424wr_uart_device = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM,
+	.dev.platform_data	= mi424wr_uart_platform_data,
+	.num_resources	= ARRAY_SIZE(mi424wr_uart_resources),
+	.resource	= mi424wr_uart_resources,
+};
+
+static struct flash_platform_data mi424wr_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource mi424wr_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device mi424wr_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev.platform_data = &mi424wr_flash_data,
+	.num_resources	= 1,
+	.resource	= &mi424wr_flash_resource,
+};
+
+static int mi424wr_spi_boardinfo_setup(struct spi_board_info *bi,
+		struct spi_master *master, void *data)
+{
+
+	strlcpy(bi->modalias, "spi-ks8995", sizeof(bi->modalias));
+
+	bi->max_speed_hz = 5000000 /* Hz */;
+	bi->bus_num = master->bus_num;
+	bi->mode = SPI_MODE_0;
+
+	return 0;
+}
+
+static struct spi_gpio_platform_data mi424wr_spi_bus_data = {
+	.pin_cs			= MI424WR_KSSPI_SELECT,
+	.pin_clk		= MI424WR_KSSPI_CLOCK,
+	.pin_miso		= MI424WR_KSSPI_RXD,
+	.pin_mosi		= MI424WR_KSSPI_TXD,
+	.cs_activelow		= 1,
+	.no_spi_delay		= 1,
+	.boardinfo_setup	= mi424wr_spi_boardinfo_setup,
+};
+
+static struct gpio_led mi424wr_gpio_led[] = {
+	{
+		.name		= "moca-wan",	/* green led */
+		.gpio		= MI424WR_MOCA_WAN_LED,
+		.active_low	= 0,
+	}
+};
+
+static struct gpio_led_platform_data mi424wr_gpio_leds_data = {
+	.num_leds	= 1,
+	.leds		= mi424wr_gpio_led,
+};
+
+static struct platform_device mi424wr_gpio_leds = {
+	.name		= "leds-gpio",
+	.id		= -1,
+	.dev.platform_data = &mi424wr_gpio_leds_data,
+};
+
+static uint16_t latch_value = MI424WR_LATCH_DEFAULT;
+static uint16_t __iomem *iobase;
+
+static void mi424wr_latch_set_led(u8 bit, enum led_brightness value)
+{
+
+	if (((MI424WR_LATCH_MASK >> bit) & 1) ^ (value == LED_OFF))
+		latch_value &= ~(0x1 << bit);
+	else
+		latch_value |= (0x1 << bit);
+
+	__raw_writew(latch_value, iobase);
+
+}
+
+static struct latch_led mi424wr_latch_led[] = {
+	{
+		.name	= "power-alarm",
+		.bit	= MI424WR_LATCH_ALARM_LED,
+	},
+	{
+		.name	= "power-ok",
+		.bit	= MI424WR_LATCH_POWER_LED,
+	},
+	{
+		.name	= "wireless",	/* green led */
+		.bit	= MI424WR_LATCH_WIRELESS_LED,
+	},
+	{
+		.name	= "inet-down",	/* red led */
+		.bit	= MI424WR_LATCH_INET_DOWN_LED,
+	},
+	{
+		.name	= "inet-up",	/* green led */
+		.bit	= MI424WR_LATCH_INET_OK_LED,
+	},
+	{
+		.name	= "moca-lan",	/* green led */
+		.bit	= MI424WR_LATCH_MOCA_LAN_LED,
+	},
+	{
+		.name	= "wan-alarm",	/* red led */
+		.bit	= MI424WR_LATCH_WAN_ALARM_LED,
+	}
+};
+
+static struct latch_led_platform_data mi424wr_latch_leds_data = {
+	.num_leds	= ARRAY_SIZE(mi424wr_latch_led),
+	.mem		= 0x51000000,
+	.leds		= mi424wr_latch_led,
+	.set_led        = mi424wr_latch_set_led,
+};
+
+static struct platform_device mi424wr_latch_leds = {
+	.name		= "leds-latch",
+	.id		= -1,
+	.dev.platform_data = &mi424wr_latch_leds_data,
+};
+
+static struct platform_device mi424wr_spi_bus = {
+	.name		= "spi-gpio",
+	.id		= 0,
+	.dev.platform_data = &mi424wr_spi_bus_data,
+};
+
+static struct eth_plat_info mi424wr_npeb_data = {
+	.phy		= 17,	/* KS8721 */
+	.rxq		= 3,
+	.txreadyq	= 20,
+};
+
+static struct eth_plat_info mi424wr_npec_data = {
+	.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
+	.phy_mask	= 0x1e, /* ports 1-4 of the KS8995 switch */
+	.rxq		= 4,
+	.txreadyq	= 21,
+};
+
+static struct platform_device mi424wr_npe_devices[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= &mi424wr_npec_data,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= &mi424wr_npeb_data,
+	}
+};
+
+static struct platform_device *mi424wr_devices[] __initdata = {
+	&mi424wr_uart_device,
+	&mi424wr_flash,
+	&mi424wr_gpio_leds,
+	&mi424wr_latch_leds,
+	&mi424wr_spi_bus,
+	&mi424wr_npe_devices[0],
+	&mi424wr_npe_devices[1],
+};
+
+static void __init mi424wr_init(void)
+{
+	ixp4xx_sys_init();
+
+	mi424wr_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	mi424wr_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_8M - 1;
+
+	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+	*IXP4XX_EXP_CS1 = MI424WR_CS1_CONFIG;
+
+	/* configure button as input
+	 */
+	gpio_line_config(MI424WR_BUTTON_GPIO, IXP4XX_GPIO_IN);
+
+	/* Initialize LEDs and enables PCI bus.
+	 */
+	iobase = ioremap_nocache(IXP4XX_EXP_BUS_BASE(1), 0x1000);
+	__raw_writew(latch_value, iobase);
+
+	platform_add_devices(mi424wr_devices, ARRAY_SIZE(mi424wr_devices));
+}
+
+
+MACHINE_START(MI424WR, "Actiontec MI424WR")
+	/* Maintainer: Jose Vasconcellos */
+	.phys_io	= IXP4XX_UART2_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_UART2_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= mi424wr_init,
+MACHINE_END
+
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -23,6 +23,7 @@ obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp42
+ obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt300nv2-pci.o
+ obj-pci-$(CONFIG_MACH_AP1000)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_TW5334)		+= tw5334-pci.o
+obj-pci-$(CONFIG_MACH_MI424WR)		+= mi424wr-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -44,6 +45,7 @@ obj-$(CONFIG_MACH_COMPEX)	+= compex-setu
+ obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv2-setup.o
+ obj-$(CONFIG_MACH_AP1000)	+= ap1000-setup.o
+ obj-$(CONFIG_MACH_TW5334)	+= tw5334-setup.o
+obj-$(CONFIG_MACH_MI424WR)	+= mi424wr-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -229,6 +229,13 @@ config MACH_GTWX5715
+ 		"High Speed" UART is n/c (as far as I can tell)
+ 		20 Pin ARM/Xscale JTAG interface on J2
+ 
+config MACH_MI424WR
+	bool "Actiontec MI424WR"
+	depends on ARCH_IXP4XX
+	select PCI
+	help
+		Add support for the Actiontec MI424-WR.
+
+ comment "IXP4xx Options"
+ 
+ config IXP4XX_INDIRECT_PCI
+--- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig
+@@ -172,6 +172,7 @@ CONFIG_MACH_FSG=y
+ CONFIG_CPU_IXP46X=y
+ CONFIG_CPU_IXP43X=y
+ CONFIG_MACH_GTWX5715=y
+CONFIG_MACH_MI424WR=y
+ 
+ #
+ # IXP4xx Options
--- a/target/linux/ixp4xx/patches-2.6.28/190-cambria_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/190-cambria_support.patch
@ -0,0 +1,553 @@
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/cambria-pci.c
+@@ -0,0 +1,74 @@
+/*
+ * arch/arch/mach-ixp4xx/cambria-pci.c
+ *
+ * PCI setup routines for Gateworks Cambria series
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ *	Copyright (C) 2002 Jungo Software Technologies.
+ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+#include <asm/mach/pci.h>
+
+extern void ixp4xx_pci_preinit(void);
+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
+
+void __init cambria_pci_preinit(void)
+{
+	set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
+
+	ixp4xx_pci_preinit();
+}
+
+static int __init cambria_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot == 1)
+		return IRQ_IXP4XX_GPIO11;
+	else if (slot == 2)
+		return IRQ_IXP4XX_GPIO10;
+	else if (slot == 3)
+		return IRQ_IXP4XX_GPIO9;
+	else if (slot == 4)
+		return IRQ_IXP4XX_GPIO8;
+	else return -1;
+}
+
+struct hw_pci cambria_pci __initdata = {
+	.nr_controllers = 1,
+	.preinit =        cambria_pci_preinit,
+	.swizzle =        pci_std_swizzle,
+	.setup =          ixp4xx_setup,
+	.scan =           ixp4xx_scan_bus,
+	.map_irq =        cambria_map_irq,
+};
+
+int __init cambria_pci_init(void)
+{
+	if (machine_is_cambria())
+		pci_common_init(&cambria_pci);
+	return 0;
+}
+
+subsys_initcall(cambria_pci_init);
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/cambria-setup.c
+@@ -0,0 +1,429 @@
+/*
+ * arch/arm/mach-ixp4xx/cambria-setup.c
+ *
+ * Board setup for the Gateworks Cambria series
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <kaloz@openwrt.org>
+ */
+
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+#include <linux/i2c/at24.h>
+#include <linux/if_ether.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/leds.h>
+#include <linux/memory.h>
+#include <linux/netdevice.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+#include <linux/socket.h>
+#include <linux/types.h>
+#include <linux/tty.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+#include <asm/setup.h>
+
+struct cambria_board_info {
+	unsigned char	*model;
+	void		(*setup)(void);
+};
+
+static struct cambria_board_info *cambria_info __initdata;
+
+static struct flash_platform_data cambria_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource cambria_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device cambria_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &cambria_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &cambria_flash_resource,
+};
+
+static struct i2c_gpio_platform_data cambria_i2c_gpio_data = {
+	.sda_pin	= 7,
+	.scl_pin	= 6,
+};
+
+static struct platform_device cambria_i2c_gpio = {
+	.name		= "i2c-gpio",
+	.id		= 0,
+	.dev = {
+		.platform_data	= &cambria_i2c_gpio_data,
+	},
+};
+
+static struct eth_plat_info cambria_npec_data = {
+	.phy		= 1,
+	.rxq		= 4,
+	.txreadyq	= 21,
+};
+
+static struct eth_plat_info cambria_npea_data = {
+	.phy		= 2,
+	.rxq		= 2,
+	.txreadyq	= 19,
+};
+
+static struct platform_device cambria_npec_device = {
+	.name			= "ixp4xx_eth",
+	.id			= IXP4XX_ETH_NPEC,
+	.dev.platform_data	= &cambria_npec_data,
+};
+
+static struct platform_device cambria_npea_device = {
+	.name			= "ixp4xx_eth",
+	.id			= IXP4XX_ETH_NPEA,
+	.dev.platform_data	= &cambria_npea_data,
+};
+
+static struct resource cambria_uart_resource = {
+	.start	= IXP4XX_UART1_BASE_PHYS,
+	.end	= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct plat_serial8250_port cambria_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device cambria_uart = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM,
+	.dev = {
+		.platform_data	= cambria_uart_data,
+	},
+	.num_resources	= 1,
+	.resource	= &cambria_uart_resource,
+};
+
+static struct resource cambria_pata_resources[] = {
+	{
+		.flags	= IORESOURCE_MEM
+	},
+	{
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.name	= "intrq",
+		.start	= IRQ_IXP4XX_GPIO12,
+		.end	= IRQ_IXP4XX_GPIO12,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct ixp4xx_pata_data cambria_pata_data = {
+	.cs0_bits	= 0xbfff3c03,
+	.cs1_bits	= 0xbfff3c03,
+};
+
+static struct platform_device cambria_pata = {
+	.name			= "pata_ixp4xx_cf",
+	.id			= 0,
+	.dev.platform_data      = &cambria_pata_data,
+	.num_resources		= ARRAY_SIZE(cambria_pata_resources),
+	.resource		= cambria_pata_resources,
+};
+
+static struct gpio_led cambria_gpio_leds[] = {
+	{
+		.name		= "user",  /* green led */
+		.gpio		= 5,
+		.active_low 	= 1,
+	}
+};
+
+static struct gpio_led_platform_data cambria_gpio_leds_data = {
+	.num_leds	= 1,
+	.leds		= cambria_gpio_leds,
+};
+
+static struct platform_device cambria_gpio_leds_device = {
+	.name		= "leds-gpio",
+	.id		= -1,
+	.dev.platform_data = &cambria_gpio_leds_data,
+};
+
+static struct latch_led cambria_latch_leds[] = {
+	{
+		.name	= "ledA",  /* green led */
+		.bit	= 0,
+	},
+	{
+		.name	= "ledB",  /* green led */
+		.bit	= 1,
+	},
+	{
+		.name	= "ledC",  /* green led */
+		.bit	= 2,
+	},
+	{
+		.name	= "ledD",  /* green led */
+		.bit	= 3,
+	},
+	{
+		.name	= "ledE",  /* green led */
+		.bit	= 4,
+	},
+	{
+		.name	= "ledF",  /* green led */
+		.bit	= 5,
+	},
+	{
+		.name	= "ledG",  /* green led */
+		.bit	= 6,
+	},
+	{
+		.name	= "ledH",  /* green led */
+		.bit	= 7,
+	}
+};
+
+static struct latch_led_platform_data cambria_latch_leds_data = {
+	.num_leds	= 8,
+	.leds		= cambria_latch_leds,
+	.mem		= 0x53F40000,
+};
+
+static struct platform_device cambria_latch_leds_device = {
+	.name		= "leds-latch",
+	.id		= -1,
+	.dev.platform_data = &cambria_latch_leds_data,
+};
+
+static struct resource cambria_usb0_resources[] = {
+	{
+		.start	= 0xCD000000,
+		.end	= 0xCD000300,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= 32,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct resource cambria_usb1_resources[] = {
+	{
+		.start	= 0xCE000000,
+		.end	= 0xCE000300,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= 33,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static u64 ehci_dma_mask = ~(u32)0;
+
+static struct platform_device cambria_usb0_device =  {
+	.name		= "ixp4xx-ehci",
+	.id		= 0,
+	.resource	= cambria_usb0_resources,
+	.num_resources	= ARRAY_SIZE(cambria_usb0_resources),
+	.dev = {
+		.dma_mask		= &ehci_dma_mask,
+		.coherent_dma_mask	= 0xffffffff,
+	},
+};
+
+static struct platform_device cambria_usb1_device = {
+	.name		= "ixp4xx-ehci",
+	.id		= 1,
+	.resource	= cambria_usb1_resources,
+	.num_resources	= ARRAY_SIZE(cambria_usb1_resources),
+	.dev = {
+		.dma_mask		= &ehci_dma_mask,
+		.coherent_dma_mask	= 0xffffffff,
+	},
+};
+
+static struct platform_device *cambria_devices[] __initdata = {
+	&cambria_i2c_gpio,
+	&cambria_flash,
+	&cambria_uart,
+};
+
+static void __init cambria_gw23xx_setup(void)
+{
+	platform_device_register(&cambria_npec_device);
+	platform_device_register(&cambria_npea_device);
+}
+
+static void __init cambria_gw2350_setup(void)
+{
+	platform_device_register(&cambria_npec_device);
+	platform_device_register(&cambria_npea_device);
+
+	platform_device_register(&cambria_usb0_device);
+	platform_device_register(&cambria_usb1_device);
+
+	platform_device_register(&cambria_gpio_leds_device);
+}
+
+static void __init cambria_gw2358_setup(void)
+{
+	platform_device_register(&cambria_npec_device);
+	platform_device_register(&cambria_npea_device);
+
+	platform_device_register(&cambria_usb0_device);
+	platform_device_register(&cambria_usb1_device);
+
+	platform_device_register(&cambria_pata);
+
+	platform_device_register(&cambria_latch_leds_device);
+}
+
+static struct cambria_board_info cambria_boards[] __initdata = {
+	{
+		.model	= "GW2350",
+		.setup	= cambria_gw2350_setup,
+	}, {
+		.model	= "GW2358",
+		.setup	= cambria_gw2358_setup,
+	}
+};
+
+static struct cambria_board_info * __init cambria_find_board_info(char *model)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(cambria_boards); i++) {
+		struct cambria_board_info *info = &cambria_boards[i];
+		if (strcmp(info->model, model) == 0)
+			return info;
+	}
+
+	return NULL;
+}
+
+static struct at24_iface *at24_if;
+
+static int at24_setup(struct at24_iface *iface, void *context)
+{
+	char mac_addr[ETH_ALEN];
+	char model[6];
+
+	at24_if = iface;
+
+	/* Read MAC addresses */
+	if (at24_if->read(at24_if, mac_addr, 0x0, 6) == 6) {
+		memcpy(&cambria_npec_data.hwaddr, mac_addr, ETH_ALEN);
+	}
+	if (at24_if->read(at24_if, mac_addr, 0x6, 6) == 6) {
+		memcpy(&cambria_npea_data.hwaddr, mac_addr, ETH_ALEN);
+	}
+
+	/* Read the first 6 bytes of the model number */
+	if (at24_if->read(at24_if, model, 0x20, 6) == 6) {
+		cambria_info = cambria_find_board_info(model);
+	}
+
+	return 0;
+}
+
+static struct at24_platform_data cambria_eeprom_info = {
+	.byte_len	= 1024,
+	.page_size	= 16,
+	.flags		= AT24_FLAG_READONLY,
+	.setup		= at24_setup,
+};
+
+static struct i2c_board_info __initdata cambria_i2c_board_info[] = {
+	{
+		I2C_BOARD_INFO("ds1672", 0x68),
+	},
+	{
+		I2C_BOARD_INFO("ad7418", 0x28),
+	},
+	{
+		I2C_BOARD_INFO("24c08", 0x51),
+		.platform_data	= &cambria_eeprom_info
+	},
+};
+
+static void __init cambria_init(void)
+{
+	ixp4xx_sys_init();
+
+	cambria_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	cambria_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+	platform_add_devices(cambria_devices, ARRAY_SIZE(cambria_devices));
+
+	cambria_pata_resources[0].start = 0x53e00000;
+	cambria_pata_resources[0].end = 0x53e3ffff;
+
+	cambria_pata_resources[1].start = 0x53e40000;
+	cambria_pata_resources[1].end = 0x53e7ffff;
+
+	cambria_pata_data.cs0_cfg = IXP4XX_EXP_CS3;
+	cambria_pata_data.cs1_cfg = IXP4XX_EXP_CS3;
+
+	i2c_register_board_info(0, cambria_i2c_board_info,
+				ARRAY_SIZE(cambria_i2c_board_info));
+}
+
+static int __init cambria_model_setup(void)
+{
+	if (!machine_is_cambria())
+		return 0;
+
+	if (cambria_info) {
+		printk(KERN_DEBUG "Running on Gateworks Cambria %s\n",
+				cambria_info->model);
+		cambria_info->setup();
+	} else {
+		printk(KERN_INFO "Unknown/missing Cambria model number"
+				" -- defaults will be used\n");
+		cambria_gw23xx_setup();
+	}
+
+	return 0;
+}
+late_initcall(cambria_model_setup);
+
+MACHINE_START(CAMBRIA, "Gateworks Cambria series")
+	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= cambria_init,
+MACHINE_END
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -25,6 +25,14 @@ config MACH_AVILA
+ 	  Avila Network Platform. For more information on this platform,
+ 	  see <file:Documentation/arm/IXP4xx>.
+ 
+config MACH_CAMBRIA
+	bool "Cambria"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support the Gateworks
+	  Cambria series. For more information on this platform,
+	  see <file:Documentation/arm/IXP4xx>.
+
+ config MACH_LOFT
+     bool "Loft"
+     depends on MACH_AVILA
+@@ -208,7 +216,7 @@ config CPU_IXP46X
+ 
+ config CPU_IXP43X
+ 	bool
+-	depends on MACH_KIXRP435
+	depends on MACH_KIXRP435 || MACH_CAMBRIA
+ 	default y
+ 
+ config MACH_GTWX5715
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -7,6 +7,7 @@ obj-pci-n	:=
+ 
+ obj-pci-$(CONFIG_ARCH_IXDP4XX)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_AVILA)		+= avila-pci.o
+obj-pci-$(CONFIG_MACH_CAMBRIA)		+= cambria-pci.o
+ obj-pci-$(CONFIG_MACH_IXDPG425)		+= ixdpg425-pci.o
+ obj-pci-$(CONFIG_ARCH_ADI_COYOTE)	+= coyote-pci.o
+ obj-pci-$(CONFIG_MACH_GTWX5715)		+= gtwx5715-pci.o
+@@ -29,6 +30,7 @@ obj-y	+= common.o
+ 
+ obj-$(CONFIG_ARCH_IXDP4XX)	+= ixdp425-setup.o
+ obj-$(CONFIG_MACH_AVILA)	+= avila-setup.o
+obj-$(CONFIG_MACH_CAMBRIA)	+= cambria-setup.o
+ obj-$(CONFIG_MACH_IXDPG425)	+= coyote-setup.o
+ obj-$(CONFIG_ARCH_ADI_COYOTE)	+= coyote-setup.o
+ obj-$(CONFIG_MACH_GTWX5715)	+= gtwx5715-setup.o
--- a/target/linux/ixp4xx/patches-2.6.28/191-cambria_optional_uart.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/191-cambria_optional_uart.patch
@ -0,0 +1,101 @@
+--- a/arch/arm/mach-ixp4xx/cambria-setup.c
+++ b/arch/arm/mach-ixp4xx/cambria-setup.c
+@@ -34,6 +34,7 @@
+ #include <asm/mach/arch.h>
+ #include <asm/mach/flash.h>
+ #include <asm/setup.h>
+#include <linux/irq.h>
+ 
+ struct cambria_board_info {
+ 	unsigned char	*model;
+@@ -127,6 +128,43 @@ static struct platform_device cambria_ua
+ 	.resource	= &cambria_uart_resource,
+ };
+ 
+static struct resource cambria_optional_uart_resources[] = {
+	{
+		.start	= 0x52000000,
+		.end	= 0x52000fff,
+		.flags	= IORESOURCE_MEM
+	},
+	{
+		.start	= 0x53000000,
+		.end	= 0x53000fff,
+		.flags	= IORESOURCE_MEM
+	}
+};
+
+static struct plat_serial8250_port cambria_optional_uart_data[] = {
+	{
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_BUGGY_UART,
+		.iotype		= UPIO_MEM,
+		.regshift	= 0,
+		.uartclk	= 1843200,
+	},
+	{
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_BUGGY_UART,
+		.iotype		= UPIO_MEM,
+		.regshift	= 0,
+		.uartclk	= 1843200,
+	},
+  { },
+};
+
+static struct platform_device cambria_optional_uart = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM1,
+	.dev.platform_data	= cambria_optional_uart_data,
+	.num_resources	= 2,
+	.resource	= cambria_optional_uart_resources,
+};
+
+ static struct resource cambria_pata_resources[] = {
+ 	{
+ 		.flags	= IORESOURCE_MEM
+@@ -283,6 +321,19 @@ static void __init cambria_gw23xx_setup(
+ 
+ static void __init cambria_gw2350_setup(void)
+ {
+	*IXP4XX_EXP_CS2 = 0xbfff0003;
+	set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING);
+	cambria_optional_uart_data[0].mapbase	= 0x52FF0000;
+	cambria_optional_uart_data[0].membase	= (void __iomem *)ioremap(0x52FF0000, 0x0fff);
+	cambria_optional_uart_data[0].irq		= IRQ_IXP4XX_GPIO3;
+
+	*IXP4XX_EXP_CS3 = 0xbfff0003;
+	set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING);
+	cambria_optional_uart_data[1].mapbase	= 0x53FF0000;
+	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53FF0000, 0x0fff);
+	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
+
+	platform_device_register(&cambria_optional_uart);
+ 	platform_device_register(&cambria_npec_device);
+ 	platform_device_register(&cambria_npea_device);
+ 
+@@ -290,10 +341,26 @@ static void __init cambria_gw2350_setup(
+ 	platform_device_register(&cambria_usb1_device);
+ 
+ 	platform_device_register(&cambria_gpio_leds_device);
+
+	*IXP4XX_EXP_CS2 = 0xBFFF3C43;
+	*IXP4XX_EXP_CS3 = 0xBFFF3C43;
+ }
+ 
+ static void __init cambria_gw2358_setup(void)
+ {
+	*IXP4XX_EXP_CS3 = 0xbfff0003;
+	set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING);
+	cambria_optional_uart_data[0].mapbase	= 0x53FC0000;
+	cambria_optional_uart_data[0].membase	= (void __iomem *)ioremap(0x53FC0000, 0x0fff);
+	cambria_optional_uart_data[0].irq		= IRQ_IXP4XX_GPIO3;
+
+	set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING);
+	cambria_optional_uart_data[1].mapbase	= 0x53F80000;
+	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53F80000, 0x0fff);
+	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
+
+	platform_device_register(&cambria_optional_uart);
+
+ 	platform_device_register(&cambria_npec_device);
+ 	platform_device_register(&cambria_npea_device);
+ 
--- a/target/linux/ixp4xx/patches-2.6.28/192-cambria_gpio_device.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/192-cambria_gpio_device.patch
@ -0,0 +1,46 @@
+--- a/arch/arm/mach-ixp4xx/cambria-setup.c
+++ b/arch/arm/mach-ixp4xx/cambria-setup.c
+@@ -212,6 +212,20 @@ static struct platform_device cambria_gp
+ 	.dev.platform_data = &cambria_gpio_leds_data,
+ };
+ 
+static struct resource cambria_gpio_resources[] = {
+	{
+		.name = "gpio",
+		.flags  = 0,
+	},
+};
+
+static struct platform_device cambria_gpio = {
+	.name     = "GPIODEV",
+	.id     = -1,
+	.num_resources    = ARRAY_SIZE(cambria_gpio_resources),
+	.resource   = cambria_gpio_resources,
+};
+
+ static struct latch_led cambria_latch_leds[] = {
+ 	{
+ 		.name	= "ledA",  /* green led */
+@@ -333,6 +347,11 @@ static void __init cambria_gw2350_setup(
+ 	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53FF0000, 0x0fff);
+ 	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
+ 
+	cambria_gpio_resources[0].start = (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3) | (1 << 4) |\
+																		(1 << 5) | (1 << 8) | (1 << 9) | (1 << 12);
+	cambria_gpio_resources[0].end = cambria_gpio_resources[0].start;
+
+	platform_device_register(&cambria_gpio);
+ 	platform_device_register(&cambria_optional_uart);
+ 	platform_device_register(&cambria_npec_device);
+ 	platform_device_register(&cambria_npea_device);
+@@ -359,6 +378,10 @@ static void __init cambria_gw2358_setup(
+ 	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53F80000, 0x0fff);
+ 	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
+ 
+	cambria_gpio_resources[0].start = (1 << 14);
+	cambria_gpio_resources[0].end = cambria_gpio_resources[0].start;
+
+	platform_device_register(&cambria_gpio);
+ 	platform_device_register(&cambria_optional_uart);
+ 
+ 	platform_device_register(&cambria_npec_device);
--- a/target/linux/ixp4xx/patches-2.6.28/201-npe_driver_print_license_location.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/201-npe_driver_print_license_location.patch
@ -0,0 +1,11 @@
+--- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c
+++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c
+@@ -592,6 +592,8 @@ int npe_load_firmware(struct npe *npe, c
+ 	npe_reset(npe);
+ #endif
+ 
+	print_npe(KERN_INFO, npe, "firmware's license can be found in /usr/share/doc/LICENSE.IPL\n");
+
+ 	print_npe(KERN_INFO, npe, "firmware functionality 0x%X, "
+ 		  "revision 0x%X:%X\n", (image->id >> 16) & 0xFF,
+ 		  (image->id >> 8) & 0xFF, image->id & 0xFF);
--- a/target/linux/ixp4xx/patches-2.6.28/202-npe_driver_switch_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/202-npe_driver_switch_support.patch
@ -0,0 +1,246 @@
+--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
+@@ -165,14 +165,15 @@ struct port {
+ 	struct net_device *netdev;
+ 	struct napi_struct napi;
+ 	struct net_device_stats stat;
+-	struct mii_if_info mii;
+	struct mii_if_info mii[IXP4XX_ETH_PHY_MAX_ADDR];
+ 	struct delayed_work mdio_thread;
+ 	struct eth_plat_info *plat;
+ 	buffer_t *rx_buff_tab[RX_DESCS], *tx_buff_tab[TX_DESCS];
+ 	struct desc *desc_tab;	/* coherent */
+ 	u32 desc_tab_phys;
+ 	int id;			/* logical port ID */
+-	u16 mii_bmcr;
+	u16 mii_bmcr[IXP4XX_ETH_PHY_MAX_ADDR];
+	int phy_count;
+ };
+ 
+ /* NPE message structure */
+@@ -316,12 +317,13 @@ static void mdio_write(struct net_device
+ 	spin_unlock_irqrestore(&mdio_lock, flags);
+ }
+ 
+-static void phy_reset(struct net_device *dev, int phy_id)
+static void phy_reset(struct net_device *dev, int idx)
+ {
+ 	struct port *port = netdev_priv(dev);
+	int phy_id = port->mii[idx].phy_id;
+ 	int cycles = 0;
+ 
+-	mdio_write(dev, phy_id, MII_BMCR, port->mii_bmcr | BMCR_RESET);
+	mdio_write(dev, phy_id, MII_BMCR, port->mii_bmcr[idx] | BMCR_RESET);
+ 
+ 	while (cycles < MAX_MII_RESET_RETRIES) {
+ 		if (!(mdio_read(dev, phy_id, MII_BMCR) & BMCR_RESET)) {
+@@ -335,12 +337,12 @@ static void phy_reset(struct net_device 
+ 		cycles++;
+ 	}
+ 
+-	printk(KERN_ERR "%s: MII reset failed\n", dev->name);
+	printk(KERN_ERR "%s: MII reset failed on PHY%2d\n", dev->name, phy_id);
+ }
+ 
+-static void eth_set_duplex(struct port *port)
+static void eth_set_duplex(struct port *port, int full_duplex)
+ {
+-	if (port->mii.full_duplex)
+	if (full_duplex)
+ 		__raw_writel(DEFAULT_TX_CNTRL0 & ~TX_CNTRL0_HALFDUPLEX,
+ 			     &port->regs->tx_control[0]);
+ 	else
+@@ -348,7 +350,7 @@ static void eth_set_duplex(struct port *
+ 			     &port->regs->tx_control[0]);
+ }
+ 
+-
+#if 0
+ static void phy_check_media(struct port *port, int init)
+ {
+ 	if (mii_check_media(&port->mii, 1, init))
+@@ -367,7 +369,63 @@ static void phy_check_media(struct port 
+ 		}
+ 	}
+ }
+#else
+static void phy_update_link(struct net_device *dev, int link)
+{
+	int prev_link = netif_carrier_ok(dev);
+
+	if (!prev_link && link) {
+		printk(KERN_INFO "%s: link up\n", dev->name);
+		netif_carrier_on(dev);
+	} else if (prev_link && !link) {
+		printk(KERN_INFO "%s: link down\n", dev->name);
+		netif_carrier_off(dev);
+	}
+}
+
+static void phy_check_media(struct port *port, int init)
+{
+	struct net_device *dev = port->netdev;
+
+	if (port->phy_count == 1) {
+		struct mii_if_info *mii = &port->mii[0];
+
+		if (mii_check_media(mii, 1, init))
+			eth_set_duplex(port, mii->full_duplex);
+
+		if (mii->force_media) /* mii_check_media() doesn't work */
+			phy_update_link(dev, mii_link_ok(mii));
+	} else {
+		int cur_link = 0;
+		int i;
+
+		if (init)
+			eth_set_duplex(port, 1);
+
+		for (i = 0; i < port->phy_count; i++)
+			cur_link |= mii_link_ok(&port->mii[i]);
+
+		phy_update_link(dev, cur_link);
+	}
+}
+#endif
+
+static void phy_power_down(struct net_device *dev, int idx)
+{
+	struct port *port = netdev_priv(dev);
+	int phy_id = port->mii[idx].phy_id;
+
+	port->mii_bmcr[idx] = mdio_read(dev, phy_id, MII_BMCR) &
+						~(BMCR_RESET | BMCR_PDOWN);
+	mdio_write(dev, phy_id, MII_BMCR, port->mii_bmcr[idx] | BMCR_PDOWN);
+}
+
+static void phy_power_up(struct net_device *dev, int idx)
+{
+	struct port *port = netdev_priv(dev);
+ 
+	mdio_write(dev, port->mii[idx].phy_id, MII_BMCR, port->mii_bmcr[idx]);
+}
+ 
+ static void mdio_thread(struct work_struct *work)
+ {
+@@ -791,9 +849,12 @@ static int eth_ioctl(struct net_device *
+ 
+ 	if (!netif_running(dev))
+ 		return -EINVAL;
+-	err = generic_mii_ioctl(&port->mii, if_mii(req), cmd, &duplex_chg);
+	if (port->phy_count != 1)
+		return -EOPNOTSUPP;
+
+	err = generic_mii_ioctl(&port->mii[0], if_mii(req), cmd, &duplex_chg);
+ 	if (duplex_chg)
+-		eth_set_duplex(port);
+		eth_set_duplex(port, port->mii[0].full_duplex);
+ 	return err;
+ }
+ 
+@@ -946,7 +1007,8 @@ static int eth_open(struct net_device *d
+ 		}
+ 	}
+ 
+-	mdio_write(dev, port->plat->phy, MII_BMCR, port->mii_bmcr);
+	for (i = 0; i < port->phy_count; i++)
+		phy_power_up(dev, i);
+ 
+ 	memset(&msg, 0, sizeof(msg));
+ 	msg.cmd = NPE_VLAN_SETRXQOSENTRY;
+@@ -1106,10 +1168,8 @@ static int eth_close(struct net_device *
+ 		printk(KERN_CRIT "%s: unable to disable loopback\n",
+ 		       dev->name);
+ 
+-	port->mii_bmcr = mdio_read(dev, port->plat->phy, MII_BMCR) &
+-		~(BMCR_RESET | BMCR_PDOWN); /* may have been altered */
+-	mdio_write(dev, port->plat->phy, MII_BMCR,
+-		   port->mii_bmcr | BMCR_PDOWN);
+	for (i = 0; i < port->phy_count; i++)
+		phy_power_down(dev, i);
+ 
+ 	if (!ports_open)
+ 		qmgr_disable_irq(TXDONE_QUEUE);
+@@ -1119,6 +1179,42 @@ static int eth_close(struct net_device *
+ 	return 0;
+ }
+ 
+static void eth_add_phy(struct net_device *dev, int phy_id)
+{
+	struct port *port = netdev_priv(dev);
+	int i;
+
+	i = port->phy_count++;
+
+	port->mii[i].dev = dev;
+	port->mii[i].mdio_read = mdio_read;
+	port->mii[i].mdio_write = mdio_write;
+	port->mii[i].phy_id = phy_id;
+	port->mii[i].phy_id_mask = 0x1F;
+	port->mii[i].reg_num_mask = 0x1F;
+
+	printk(KERN_INFO "%s: MII PHY %i on %s\n", dev->name, phy_id,
+	       npe_name(port->npe));
+
+	phy_reset(dev, i);
+	phy_power_down(dev, i);
+}
+
+static void eth_init_mii(struct net_device *dev)
+{
+	struct port *port = netdev_priv(dev);
+
+	if (port->plat->phy < IXP4XX_ETH_PHY_MAX_ADDR) {
+		eth_add_phy(dev, port->plat->phy);
+	} else {
+		int i;
+		for (i = 0; i < IXP4XX_ETH_PHY_MAX_ADDR; i++)
+			if (port->plat->phy_mask & (1U << i))
+				eth_add_phy(dev, i);
+	}
+
+}
+
+ static int __devinit eth_init_one(struct platform_device *pdev)
+ {
+ 	struct port *port;
+@@ -1191,20 +1287,7 @@ static int __devinit eth_init_one(struct
+ 	__raw_writel(DEFAULT_CORE_CNTRL, &port->regs->core_control);
+ 	udelay(50);
+ 
+-	port->mii.dev = dev;
+-	port->mii.mdio_read = mdio_read;
+-	port->mii.mdio_write = mdio_write;
+-	port->mii.phy_id = plat->phy;
+-	port->mii.phy_id_mask = 0x1F;
+-	port->mii.reg_num_mask = 0x1F;
+-
+-	printk(KERN_INFO "%s: MII PHY %i on %s\n", dev->name, plat->phy,
+-	       npe_name(port->npe));
+-
+-	phy_reset(dev, plat->phy);
+-	port->mii_bmcr = mdio_read(dev, plat->phy, MII_BMCR) &
+-		~(BMCR_RESET | BMCR_PDOWN);
+-	mdio_write(dev, plat->phy, MII_BMCR, port->mii_bmcr | BMCR_PDOWN);
+	eth_init_mii(dev);
+ 
+ 	INIT_DELAYED_WORK(&port->mdio_thread, mdio_thread);
+ 	return 0;
+--- a/arch/arm/mach-ixp4xx/include/mach/platform.h
+++ b/arch/arm/mach-ixp4xx/include/mach/platform.h
+@@ -95,12 +95,15 @@ struct sys_timer;
+ #define IXP4XX_ETH_NPEB		0x10
+ #define IXP4XX_ETH_NPEC		0x20
+ 
+#define IXP4XX_ETH_PHY_MAX_ADDR	32
+
+ /* Information about built-in Ethernet MAC interfaces */
+ struct eth_plat_info {
+ 	u8 phy;		/* MII PHY ID, 0 - 31 */
+ 	u8 rxq;		/* configurable, currently 0 - 31 only */
+ 	u8 txreadyq;
+ 	u8 hwaddr[6];
+	u32 phy_mask;
+ };
+ 
+ /* Information about built-in HSS (synchronous serial) interfaces */
--- a/target/linux/ixp4xx/patches-2.6.28/203-npe_driver_phy_reset_autoneg.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/203-npe_driver_phy_reset_autoneg.patch
@ -0,0 +1,42 @@
+--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
+@@ -322,8 +322,12 @@ static void phy_reset(struct net_device 
+ 	struct port *port = netdev_priv(dev);
+ 	int phy_id = port->mii[idx].phy_id;
+ 	int cycles = 0;
+	u16 bmcr;
+ 
+-	mdio_write(dev, phy_id, MII_BMCR, port->mii_bmcr[idx] | BMCR_RESET);
+	/* reset the PHY */
+	bmcr = mdio_read(dev, phy_id, MII_BMCR);
+	bmcr |= BMCR_ANENABLE;
+	mdio_write(dev, phy_id, MII_BMCR, bmcr | BMCR_RESET);
+ 
+ 	while (cycles < MAX_MII_RESET_RETRIES) {
+ 		if (!(mdio_read(dev, phy_id, MII_BMCR) & BMCR_RESET)) {
+@@ -331,13 +335,23 @@ static void phy_reset(struct net_device 
+ 			printk(KERN_DEBUG "%s: phy_reset() took %i cycles\n",
+ 			       dev->name, cycles);
+ #endif
+-			return;
+			break;
+ 		}
+ 		udelay(1);
+ 		cycles++;
+ 	}
+ 
+-	printk(KERN_ERR "%s: MII reset failed on PHY%2d\n", dev->name, phy_id);
+	if (cycles == MAX_MII_RESET_RETRIES) {
+		printk(KERN_ERR "%s: MII reset failed on PHY%2d\n", dev->name,
+								phy_id);
+		return;
+	}
+
+	/* restart auto negotiation */
+	bmcr = mdio_read(dev, phy_id, MII_BMCR);
+	bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
+	mdio_write(dev, phy_id, MII_BMCR, bmcr);
+
+ }
+ 
+ static void eth_set_duplex(struct port *port, int full_duplex)
--- a/target/linux/ixp4xx/patches-2.6.28/204-npe_driver_ixp43x_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/204-npe_driver_ixp43x_support.patch
@ -0,0 +1,94 @@
+From cba5c286f3ea34ea4767fc00c705434a00fe2c37 Mon Sep 17 00:00:00 2001
+From: Imre Kaloz <kaloz@openwrt.org>
+Date: Thu, 26 Jun 2008 01:58:02 +0200
+Subject: [PATCH] Add support for the ethernet ports on IXP43x
+
+---
+ arch/arm/mach-ixp4xx/ixp4xx_npe.c         |    6 +++---
+ drivers/net/arm/ixp4xx_eth.c              |   13 +++++++++----
+ include/asm-arm/arch-ixp4xx/cpu.h         |    2 ++
+ include/asm-arm/arch-ixp4xx/ixp4xx-regs.h |    7 ++++---
+ 4 files changed, 18 insertions(+), 10 deletions(-)
+
+--- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c
+++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c
+@@ -575,8 +575,8 @@ int npe_load_firmware(struct npe *npe, c
+ 		for (i = 0; i < image->size; i++)
+ 			image->data[i] = swab32(image->data[i]);
+ 
+-	if (!cpu_is_ixp46x() && ((image->id >> 28) & 0xF /* device ID */)) {
+-		print_npe(KERN_INFO, npe, "IXP46x firmware ignored on "
+	if (cpu_is_ixp42x() && ((image->id >> 28) & 0xF /* device ID */)) {
+		print_npe(KERN_INFO, npe, "IXP46x/IXP43x firmware ignored on "
+ 			  "IXP42x\n");
+ 		goto err;
+ 	}
+@@ -598,7 +598,7 @@ int npe_load_firmware(struct npe *npe, c
+ 		  "revision 0x%X:%X\n", (image->id >> 16) & 0xFF,
+ 		  (image->id >> 8) & 0xFF, image->id & 0xFF);
+ 
+-	if (!cpu_is_ixp46x()) {
+	if (cpu_is_ixp42x()) {
+ 		if (!npe->id)
+ 			instr_size = NPE_A_42X_INSTR_SIZE;
+ 		else
+--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
+@@ -32,6 +32,7 @@
+ #include <linux/kernel.h>
+ #include <linux/mii.h>
+ #include <linux/platform_device.h>
+#include <mach/cpu.h>
+ #include <mach/npe.h>
+ #include <mach/qmgr.h>
+ 
+@@ -1337,12 +1338,16 @@ static struct platform_driver drv = {
+ 
+ static int __init eth_init_module(void)
+ {
+-	if (!(ixp4xx_read_feature_bits() & IXP4XX_FEATURE_NPEB_ETH0))
+-		return -ENOSYS;
+ 
+-	/* All MII PHY accesses use NPE-B Ethernet registers */
+ 	spin_lock_init(&mdio_lock);
+-	mdio_regs = (struct eth_regs __iomem *)IXP4XX_EthB_BASE_VIRT;
+	if (!cpu_is_ixp43x())
+	/* All MII PHY accesses use NPE-B Ethernet registers */
+		mdio_regs = (struct eth_regs __iomem *)IXP4XX_EthB_BASE_VIRT;
+
+	else
+	/* IXP43x lacks NPE-B and uses NPE-C for MII PHY access */
+		mdio_regs = (struct eth_regs __iomem *)IXP4XX_EthC_BASE_VIRT;
+
+ 	__raw_writel(DEFAULT_CORE_CNTRL, &mdio_regs->core_control);
+ 
+ 	return platform_driver_register(&drv);
+--- a/arch/arm/mach-ixp4xx/include/mach/cpu.h
+++ b/arch/arm/mach-ixp4xx/include/mach/cpu.h
+@@ -35,6 +35,8 @@ static inline u32 ixp4xx_read_feature_bi
+ 	val &= ~IXP4XX_FEATURE_RESERVED;
+ 	if (!cpu_is_ixp46x())
+ 		val &= ~IXP4XX_FEATURE_IXP46X_ONLY;
+	if (cpu_is_ixp42x())
+		val &= ~IXP4XX_FEATURE_IXP43X_46X;
+ 
+ 	return val;
+ }
+--- a/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
+++ b/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
+@@ -628,11 +628,12 @@
+ #define IXP4XX_FEATURE_XSCALE_MAX_FREQ	(3 << 22)
+ #define IXP4XX_FEATURE_RESERVED		(0xFF << 24)
+ 
+-#define IXP4XX_FEATURE_IXP46X_ONLY (IXP4XX_FEATURE_ECC_TIMESYNC |	\
+#define IXP4XX_FEATURE_IXP43X_46X (IXP4XX_FEATURE_ECC_TIMESYNC |	\
+ 				    IXP4XX_FEATURE_USB_HOST |		\
+ 				    IXP4XX_FEATURE_NPEA_ETH |		\
+-				    IXP4XX_FEATURE_NPEB_ETH_1_TO_3 |	\
+-				    IXP4XX_FEATURE_RSA |		\
+ 				    IXP4XX_FEATURE_XSCALE_MAX_FREQ)
+ 
+#define IXP4XX_FEATURE_IXP46X_ONLY (IXP4XX_FEATURE_NPEB_ETH_1_TO_3 |	\
+				    IXP4XX_FEATURE_RSA)
+
+ #endif
--- a/target/linux/ixp4xx/patches-2.6.28/210-npe_hss.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/210-npe_hss.patch
--- a/target/linux/ixp4xx/patches-2.6.28/295-latch_led_driver.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/295-latch_led_driver.patch
@ -0,0 +1,199 @@
+--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
+@@ -119,6 +119,12 @@ config LEDS_GPIO
+ 	  outputs. To be useful the particular board must have LEDs
+ 	  and they must be connected to the GPIO lines.
+ 
+config LEDS_LATCH
+	tristate "LED Support for Memory Latched LEDs"
+	depends on LEDS_CLASS
+	help
+		-- To Do --
+
+ config LEDS_HP_DISK
+ 	tristate "LED Support for disk protection LED on HP notebooks"
+ 	depends on LEDS_CLASS && ACPI
+--- /dev/null
+++ b/drivers/leds/leds-latch.c
+@@ -0,0 +1,149 @@
+/*
+ * LEDs driver for Memory Latched Devices
+ *
+ * Copyright (C) 2008 Gateworks Corp.
+ * Chris Lang <clang@gateworks.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/leds.h>
+#include <linux/workqueue.h>
+#include <asm/io.h>
+#include <linux/spinlock.h>
+
+static unsigned int mem_keep = 0xFF;
+static spinlock_t mem_lock;
+static unsigned char *iobase;
+
+struct latch_led_data {
+	struct led_classdev cdev;
+	struct work_struct work;
+	u8 new_level;
+	u8 bit;
+	void (*set_led)(u8 bit, enum led_brightness value);
+};
+
+static void latch_set_led(u8 bit, enum led_brightness value)
+{
+	if (value == LED_OFF)
+		mem_keep |= (0x1 << bit);
+	else
+		mem_keep &= ~(0x1 << bit);
+
+	writeb(mem_keep, iobase);
+}
+
+static void latch_led_set(struct led_classdev *led_cdev,
+	enum led_brightness value)
+{
+	struct latch_led_data *led_dat =
+		container_of(led_cdev, struct latch_led_data, cdev);
+
+	spin_lock(mem_lock);
+
+	led_dat->set_led(led_dat->bit, value);
+
+	spin_unlock(mem_lock);
+}
+
+static int latch_led_probe(struct platform_device *pdev)
+{
+	struct latch_led_platform_data *pdata = pdev->dev.platform_data;
+	struct latch_led *cur_led;
+	struct latch_led_data *leds_data, *led_dat;
+	int i, ret = 0;
+
+	if (!pdata)
+		return -EBUSY;
+
+	leds_data = kzalloc(sizeof(struct latch_led_data) * pdata->num_leds,
+				GFP_KERNEL);
+	if (!leds_data)
+		return -ENOMEM;
+
+	for (i = 0; i < pdata->num_leds; i++) {
+		cur_led = &pdata->leds[i];
+		led_dat = &leds_data[i];
+
+		led_dat->cdev.name = cur_led->name;
+		led_dat->cdev.default_trigger = cur_led->default_trigger;
+		led_dat->cdev.brightness_set = latch_led_set;
+		led_dat->cdev.brightness = LED_OFF;
+		led_dat->bit = cur_led->bit;
+		led_dat->set_led = pdata->set_led ? pdata->set_led : latch_set_led;
+
+		ret = led_classdev_register(&pdev->dev, &led_dat->cdev);
+		if (ret < 0) {
+			goto err;
+		}
+	}
+
+	if (!pdata->set_led) {
+		iobase = ioremap_nocache(pdata->mem, 0x1000);
+		writeb(0xFF, iobase);
+	}
+	platform_set_drvdata(pdev, leds_data);
+
+	return 0;
+
+err:
+	if (i > 0) {
+		for (i = i - 1; i >= 0; i--) {
+			led_classdev_unregister(&leds_data[i].cdev);
+		}
+	}
+
+	kfree(leds_data);
+
+	return ret;
+}
+
+static int __devexit latch_led_remove(struct platform_device *pdev)
+{
+	int i;
+	struct latch_led_platform_data *pdata = pdev->dev.platform_data;
+	struct latch_led_data *leds_data;
+
+	leds_data = platform_get_drvdata(pdev);
+
+	for (i = 0; i < pdata->num_leds; i++) {
+		led_classdev_unregister(&leds_data[i].cdev);
+		cancel_work_sync(&leds_data[i].work);
+	}
+
+	kfree(leds_data);
+
+	return 0;
+}
+
+static struct platform_driver latch_led_driver = {
+	.probe		= latch_led_probe,
+	.remove		= __devexit_p(latch_led_remove),
+	.driver		= {
+		.name	= "leds-latch",
+		.owner	= THIS_MODULE,
+	},
+};
+
+static int __init latch_led_init(void)
+{
+	return platform_driver_register(&latch_led_driver);
+}
+
+static void __exit latch_led_exit(void)
+{
+	platform_driver_unregister(&latch_led_driver);
+}
+
+module_init(latch_led_init);
+module_exit(latch_led_exit);
+
+MODULE_AUTHOR("Chris Lang <clang@gateworks.com>");
+MODULE_DESCRIPTION("Latch LED driver");
+MODULE_LICENSE("GPL");
+--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
+@@ -18,6 +18,7 @@ obj-$(CONFIG_LEDS_COBALT_RAQ)		+= leds-c
+ obj-$(CONFIG_LEDS_SUNFIRE)		+= leds-sunfire.o
+ obj-$(CONFIG_LEDS_PCA9532)		+= leds-pca9532.o
+ obj-$(CONFIG_LEDS_GPIO)			+= leds-gpio.o
+obj-$(CONFIG_LEDS_LATCH)		+= leds-latch.o
+ obj-$(CONFIG_LEDS_CLEVO_MAIL)		+= leds-clevo-mail.o
+ obj-$(CONFIG_LEDS_HP6XX)		+= leds-hp6xx.o
+ obj-$(CONFIG_LEDS_FSG)			+= leds-fsg.o
+--- a/include/linux/leds.h
+++ b/include/linux/leds.h
+@@ -148,5 +148,19 @@ struct gpio_led_platform_data {
+ 					unsigned long *delay_off);
+ };
+ 
+/* For the leds-latch driver */
+struct latch_led {
+	const char *name;
+	char *default_trigger;
+	unsigned  bit;
+};
+
+struct latch_led_platform_data {
+	int     num_leds;
+	u32     mem;
+	struct latch_led *leds;
+	void	(*set_led)(u8 bit, enum led_brightness value);
+};
+
+ 
+ #endif		/* __LINUX_LEDS_H_INCLUDED */
--- a/target/linux/ixp4xx/patches-2.6.28/300-avila_fetch_mac.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/300-avila_fetch_mac.patch
@ -0,0 +1,244 @@
+--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
+@@ -14,10 +14,16 @@
+ #include <linux/kernel.h>
+ #include <linux/init.h>
+ #include <linux/device.h>
+#include <linux/if_ether.h>
+#include <linux/socket.h>
+#include <linux/netdevice.h>
+ #include <linux/serial.h>
+ #include <linux/tty.h>
+ #include <linux/serial_8250.h>
+ #include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+
+ #include <linux/i2c-gpio.h>
+ 
+ #include <asm/types.h>
+@@ -29,6 +35,13 @@
+ #include <asm/mach/arch.h>
+ #include <asm/mach/flash.h>
+ 
+struct avila_board_info {
+	unsigned char	*model;
+	void		(*setup)(void);
+};
+
+static struct avila_board_info *avila_info __initdata;
+
+ static struct flash_platform_data avila_flash_data = {
+ 	.map_name	= "cfi_probe",
+ 	.width		= 2,
+@@ -132,16 +145,181 @@ static struct platform_device avila_pata
+ 	.resource		= avila_pata_resources,
+ };
+ 
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info avila_npeb_data = {
+	.phy		= 0,
+	.rxq		= 3,
+	.txreadyq	= 20,
+};
+
+static struct eth_plat_info avila_npec_data = {
+	.phy		= 1,
+	.rxq		= 4,
+	.txreadyq	= 21,
+};
+
+static struct platform_device avila_npeb_device = {
+	.name			= "ixp4xx_eth",
+	.id			= IXP4XX_ETH_NPEB,
+	.dev.platform_data	= &avila_npeb_data,
+};
+
+static struct platform_device avila_npec_device = {
+	.name			= "ixp4xx_eth",
+	.id			= IXP4XX_ETH_NPEC,
+	.dev.platform_data	= &avila_npec_data,
+};
+
+ static struct platform_device *avila_devices[] __initdata = {
+ 	&avila_i2c_gpio,
+ 	&avila_flash,
+ 	&avila_uart
+ };
+ 
+static void __init avila_gw23xx_setup(void)
+{
+	platform_device_register(&avila_npeb_device);
+	platform_device_register(&avila_npec_device);
+}
+
+static void __init avila_gw2342_setup(void)
+{
+	platform_device_register(&avila_npeb_device);
+	platform_device_register(&avila_npec_device);
+}
+
+static void __init avila_gw2345_setup(void)
+{
+	avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR;
+	avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */
+	platform_device_register(&avila_npeb_device);
+
+	avila_npec_data.phy = 5; /* port 5 of the KS8995 switch */
+	platform_device_register(&avila_npec_device);
+}
+
+static void __init avila_gw2347_setup(void)
+{
+	platform_device_register(&avila_npeb_device);
+}
+
+static void __init avila_gw2348_setup(void)
+{
+	platform_device_register(&avila_npeb_device);
+	platform_device_register(&avila_npec_device);
+}
+
+static void __init avila_gw2353_setup(void)
+{
+	platform_device_register(&avila_npeb_device);
+}
+
+static void __init avila_gw2355_setup(void)
+{
+	avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR;
+	avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */
+	platform_device_register(&avila_npeb_device);
+
+	avila_npec_data.phy = 16;
+	platform_device_register(&avila_npec_device);
+}
+
+static void __init avila_gw2357_setup(void)
+{
+	platform_device_register(&avila_npeb_device);
+}
+
+static struct avila_board_info avila_boards[] __initdata = {
+	{
+		.model		= "GW2342",
+		.setup		= avila_gw2342_setup,
+	}, {
+		.model		= "GW2345",
+		.setup		= avila_gw2345_setup,
+	}, {
+		.model		= "GW2347",
+		.setup		= avila_gw2347_setup,
+	}, {
+		.model		= "GW2348",
+		.setup		= avila_gw2348_setup,
+	}, {
+		.model		= "GW2353",
+		.setup		= avila_gw2353_setup,
+	}, {
+		.model		= "GW2355",
+		.setup		= avila_gw2355_setup,
+	}, {
+		.model		= "GW2357",
+		.setup		= avila_gw2357_setup,
+	}
+};
+
+static struct avila_board_info * __init avila_find_board_info(char *model)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(avila_boards); i++) {
+		struct avila_board_info *info = &avila_boards[i];
+		if (strcmp(info->model, model) == 0)
+			return info;
+	}
+
+	return NULL;
+}
+
+static struct at24_iface *at24_if;
+
+static int at24_setup(struct at24_iface *iface, void *context)
+{
+	char mac_addr[ETH_ALEN];
+	char model[6];
+
+	at24_if = iface;
+
+	/* Read MAC addresses */
+	if (at24_if->read(at24_if, mac_addr, 0x0, 6) == 6) {
+		memcpy(&avila_npeb_data.hwaddr, mac_addr, ETH_ALEN);
+	}
+	if (at24_if->read(at24_if, mac_addr, 0x6, 6) == 6) {
+		memcpy(&avila_npec_data.hwaddr, mac_addr, ETH_ALEN);
+	}
+
+	/* Read the first 6 bytes of the model number */
+	if (at24_if->read(at24_if, model, 0x20, 6) == 6) {
+		avila_info = avila_find_board_info(model);
+	}
+
+	return 0;
+}
+
+static struct at24_platform_data avila_eeprom_info = {
+	.byte_len	= 1024,
+	.page_size	= 16,
+	.flags		= AT24_FLAG_READONLY,
+	.setup		= at24_setup,
+};
+
+static struct i2c_board_info __initdata avila_i2c_board_info[] = {
+	{
+		I2C_BOARD_INFO("ds1672", 0x68),
+	},
+	{
+		I2C_BOARD_INFO("ad7418", 0x28),
+	},
+	{
+		I2C_BOARD_INFO("24c08", 0x51),
+		.platform_data	= &avila_eeprom_info
+	},
+};
+
+ static void __init avila_init(void)
+ {
+ 	ixp4xx_sys_init();
+ 
+	/*
+	 * These devices are present on all Avila models and don't need any
+	 * model specific setup.
+	 */
+ 	avila_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ 	avila_flash_resource.end =
+ 		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
+@@ -159,7 +337,28 @@ static void __init avila_init(void)
+ 
+ 	platform_device_register(&avila_pata);
+ 
+		i2c_register_board_info(0, avila_i2c_board_info,
+				ARRAY_SIZE(avila_i2c_board_info));
+}
+
+static int __init avila_model_setup(void)
+{
+	if (!machine_is_avila())
+		return 0;
+
+	if (avila_info) {
+		printk(KERN_DEBUG "Running on Gateworks Avila %s\n",
+							avila_info->model);
+		avila_info->setup();
+	} else {
+		printk(KERN_INFO "Unknown/missing Avila model number"
+						" -- defaults will be used\n");
+		avila_gw23xx_setup();
+	}
+
+	return 0;
+ }
+late_initcall(avila_model_setup);
+ 
+ MACHINE_START(AVILA, "Gateworks Avila Network Platform")
+ 	/* Maintainer: Deepak Saxena <dsaxena@plexity.net> */
--- a/target/linux/ixp4xx/patches-2.6.28/301-avila_led.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/301-avila_led.patch
@ -0,0 +1,171 @@
+--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
+@@ -24,6 +24,7 @@
+ #include <linux/i2c.h>
+ #include <linux/i2c/at24.h>
+ 
+#include <linux/leds.h>
+ #include <linux/i2c-gpio.h>
+ 
+ #include <asm/types.h>
+@@ -170,6 +171,72 @@ static struct platform_device avila_npec
+ 	.dev.platform_data	= &avila_npec_data,
+ };
+ 
+static struct gpio_led avila_gpio_leds[] = {
+	{
+		.name		= "user",  /* green led */
+		.gpio		= AVILA_GW23XX_LED_USER_GPIO,
+		.active_low	= 1,
+	}
+};
+
+static struct gpio_led_platform_data avila_gpio_leds_data = {
+	.num_leds		= 1,
+	.leds			= avila_gpio_leds,
+};
+
+static struct platform_device avila_gpio_leds_device = {
+	.name			= "leds-gpio",
+	.id			= -1,
+	.dev.platform_data	= &avila_gpio_leds_data,
+};
+
+static struct latch_led avila_latch_leds[] = {
+	{
+		.name	= "led0",  /* green led */
+		.bit	= 0,
+	},
+	{
+		.name	= "led1",  /* green led */
+		.bit	= 1,
+	},
+	{
+		.name	= "led2",  /* green led */
+		.bit	= 2,
+	},
+	{
+		.name	= "led3",  /* green led */
+		.bit	= 3,
+	},
+	{
+		.name	= "led4",  /* green led */
+		.bit	= 4,
+	},
+	{
+		.name	= "led5",  /* green led */
+		.bit	= 5,
+	},
+	{
+		.name	= "led6",  /* green led */
+		.bit	= 6,
+	},
+	{
+		.name	= "led7",  /* green led */
+		.bit	= 7,
+	}
+};
+
+static struct latch_led_platform_data avila_latch_leds_data = {
+	.num_leds	= 8,
+	.leds		= avila_latch_leds,
+	.mem		= 0x51000000,
+};
+
+static struct platform_device avila_latch_leds_device = {
+	.name			= "leds-latch",
+	.id			= -1,
+	.dev.platform_data	= &avila_latch_leds_data,
+};
+
+ static struct platform_device *avila_devices[] __initdata = {
+ 	&avila_i2c_gpio,
+ 	&avila_flash,
+@@ -180,12 +247,16 @@ static void __init avila_gw23xx_setup(vo
+ {
+ 	platform_device_register(&avila_npeb_device);
+ 	platform_device_register(&avila_npec_device);
+
+	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2342_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
+ 	platform_device_register(&avila_npec_device);
+
+	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2345_setup(void)
+@@ -196,22 +267,30 @@ static void __init avila_gw2345_setup(vo
+ 
+ 	avila_npec_data.phy = 5; /* port 5 of the KS8995 switch */
+ 	platform_device_register(&avila_npec_device);
+
+	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2347_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
+
+	avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
+	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2348_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
+ 	platform_device_register(&avila_npec_device);
+
+	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2353_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
+	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2355_setup(void)
+@@ -222,11 +301,29 @@ static void __init avila_gw2355_setup(vo
+ 
+ 	avila_npec_data.phy = 16;
+ 	platform_device_register(&avila_npec_device);
+
+	platform_device_register(&avila_gpio_leds_device);
+
+	*IXP4XX_EXP_CS4 |= 0xbfff3c03;
+	avila_latch_leds[0].name = "RXD";
+	avila_latch_leds[1].name = "TXD";
+	avila_latch_leds[2].name = "POL";
+	avila_latch_leds[3].name = "LNK";
+	avila_latch_leds[4].name = "ERR";
+	avila_latch_leds_data.num_leds = 5;
+	avila_latch_leds_data.mem = 0x54000000;
+	platform_device_register(&avila_latch_leds_device);
+ }
+ 
+ static void __init avila_gw2357_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
+
+	avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
+	platform_device_register(&avila_gpio_leds_device);
+
+	*IXP4XX_EXP_CS1 |= 0xbfff3c03;
+	platform_device_register(&avila_latch_leds_device);
+ }
+ 
+ static struct avila_board_info avila_boards[] __initdata = {
+--- a/arch/arm/mach-ixp4xx/include/mach/avila.h
+++ b/arch/arm/mach-ixp4xx/include/mach/avila.h
+@@ -36,4 +36,6 @@
+ #define AVILA_PCI_INTC_PIN	9
+ #define AVILA_PCI_INTD_PIN	8
+ 
+-
+/* User LEDs */
+#define AVILA_GW23XX_LED_USER_GPIO	3
+#define AVILA_GW23X7_LED_USER_GPIO	4
--- a/target/linux/ixp4xx/patches-2.6.28/302-avila_gpio_device.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/302-avila_gpio_device.patch
@ -0,0 +1,41 @@
+--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
+@@ -237,10 +237,28 @@ static struct platform_device avila_latc
+ 	.dev.platform_data	= &avila_latch_leds_data,
+ };
+ 
+static struct resource avila_gpio_resources[] = {
+	{
+		.name	= "gpio",
+		/* FIXME: gpio mask should be model specific */
+		.start	= AVILA_GPIO_MASK,
+		.end	= AVILA_GPIO_MASK,
+		.flags	= 0,
+	},
+};
+
+static struct platform_device avila_gpio = {
+	.name			= "GPIODEV",
+	.id			= -1,
+	.num_resources		= ARRAY_SIZE(avila_gpio_resources),
+	.resource		= avila_gpio_resources,
+};
+
+ static struct platform_device *avila_devices[] __initdata = {
+ 	&avila_i2c_gpio,
+ 	&avila_flash,
+-	&avila_uart
+	&avila_uart,
+	&avila_gpio,
+ };
+ 
+ static void __init avila_gw23xx_setup(void)
+--- a/arch/arm/mach-ixp4xx/include/mach/avila.h
+++ b/arch/arm/mach-ixp4xx/include/mach/avila.h
+@@ -39,3 +39,6 @@
+ /* User LEDs */
+ #define AVILA_GW23XX_LED_USER_GPIO	3
+ #define AVILA_GW23X7_LED_USER_GPIO	4
+
+/* gpio mask used by platform device */
+#define AVILA_GPIO_MASK	(1 << 1) | (1 << 3) | (1 << 5) | (1 << 7) | (1 << 9)
--- a/target/linux/ixp4xx/patches-2.6.28/303-avila_gw23x7_phy_quirk.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/303-avila_gw23x7_phy_quirk.patch
@ -0,0 +1,46 @@
+--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
+@@ -291,6 +291,7 @@ static void __init avila_gw2345_setup(vo
+ 
+ static void __init avila_gw2347_setup(void)
+ {
+	avila_npeb_data.quirks |= IXP4XX_ETH_QUIRK_GW23X7;
+ 	platform_device_register(&avila_npeb_device);
+ 
+ 	avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
+@@ -335,6 +336,7 @@ static void __init avila_gw2355_setup(vo
+ 
+ static void __init avila_gw2357_setup(void)
+ {
+	avila_npeb_data.quirks |= IXP4XX_ETH_QUIRK_GW23X7;
+ 	platform_device_register(&avila_npeb_device);
+ 
+ 	avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
+--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
+@@ -348,6 +348,14 @@ static void phy_reset(struct net_device 
+ 		return;
+ 	}
+ 
+	if (port->plat->quirks & IXP4XX_ETH_QUIRK_GW23X7) {
+		mdio_write(dev, 1, 0x19,
+				(mdio_read(dev, 1, 0x19) & 0xfffe) | 0x8000);
+
+		printk(KERN_DEBUG "%s: phy_id of the DP83848 changed to 0\n",
+								dev->name);
+	}
+
+ 	/* restart auto negotiation */
+ 	bmcr = mdio_read(dev, phy_id, MII_BMCR);
+ 	bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
+--- a/arch/arm/mach-ixp4xx/include/mach/platform.h
+++ b/arch/arm/mach-ixp4xx/include/mach/platform.h
+@@ -104,6 +104,8 @@ struct eth_plat_info {
+ 	u8 txreadyq;
+ 	u8 hwaddr[6];
+ 	u32 phy_mask;
+	u32 quirks;
+#define IXP4XX_ETH_QUIRK_GW23X7		0x00000001
+ };
+ 
+ /* Information about built-in HSS (synchronous serial) interfaces */
--- a/target/linux/ixp4xx/patches-2.6.28/310-gtwx5717_spi_bus.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/310-gtwx5717_spi_bus.patch
@ -0,0 +1,53 @@
+--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+@@ -29,6 +29,8 @@
+ #include <linux/serial_8250.h>
+ #include <linux/slab.h>
+ 
+#include <linux/spi/spi_gpio.h>
+
+ #include <asm/types.h>
+ #include <asm/setup.h>
+ #include <asm/memory.h>
+@@ -121,9 +123,41 @@ static struct platform_device gtwx5715_f
+ 	.resource	= &gtwx5715_flash_resource,
+ };
+ 
+static int gtwx5715_spi_boardinfo_setup(struct spi_board_info *bi,
+		struct spi_master *master, void *data)
+{
+
+	strlcpy(bi->modalias, "spi-ks8995", sizeof(bi->modalias));
+
+	bi->max_speed_hz = 5000000 /* Hz */;
+	bi->bus_num = master->bus_num;
+	bi->mode = SPI_MODE_0;
+
+	return 0;
+}
+
+static struct spi_gpio_platform_data gtwx5715_spi_bus_data = {
+	.pin_cs			= GTWX5715_KSSPI_SELECT,
+	.pin_clk		= GTWX5715_KSSPI_CLOCK,
+	.pin_miso		= GTWX5715_KSSPI_RXD,
+	.pin_mosi		= GTWX5715_KSSPI_TXD,
+	.cs_activelow		= 1,
+	.no_spi_delay		= 1,
+	.boardinfo_setup	= gtwx5715_spi_boardinfo_setup,
+};
+
+static struct platform_device gtwx5715_spi_bus = {
+	.name		= "spi-gpio",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &gtwx5715_spi_bus_data,
+	},
+};
+
+ static struct platform_device *gtwx5715_devices[] __initdata = {
+ 	&gtwx5715_uart_device,
+ 	&gtwx5715_flash,
+	&gtwx5715_spi_bus,
+ };
+ 
+ static void __init gtwx5715_init(void)
--- a/target/linux/ixp4xx/patches-2.6.28/311-gtwx5717_mac_plat_info.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/311-gtwx5717_mac_plat_info.patch
@ -0,0 +1,40 @@
+--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+@@ -154,10 +154,37 @@ static struct platform_device gtwx5715_s
+ 	},
+ };
+ 
+static struct eth_plat_info gtwx5715_npeb_data = {
+	.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
+	.phy_mask	= 0x1e, /* ports 1-4 of the KS8995 switch */
+	.rxq		= 3,
+	.txreadyq	= 20,
+};
+
+static struct eth_plat_info gtwx5715_npec_data = {
+	.phy		= 5,	/* port 5 of the KS8995 switch */
+	.rxq		= 4,
+	.txreadyq	= 21,
+};
+
+static struct platform_device gtwx5715_npeb_device = {
+	.name			= "ixp4xx_eth",
+	.id			= IXP4XX_ETH_NPEB,
+	.dev.platform_data	= &gtwx5715_npeb_data,
+};
+
+static struct platform_device gtwx5715_npec_device = {
+	.name			= "ixp4xx_eth",
+	.id			= IXP4XX_ETH_NPEC,
+	.dev.platform_data	= &gtwx5715_npec_data,
+};
+
+ static struct platform_device *gtwx5715_devices[] __initdata = {
+ 	&gtwx5715_uart_device,
+ 	&gtwx5715_flash,
+ 	&gtwx5715_spi_bus,
+	&gtwx5715_npeb_device,
+	&gtwx5715_npec_device,
+ };
+ 
+ static void __init gtwx5715_init(void)
--- a/target/linux/ixp4xx/patches-2.6.28/312-ixp4xx_pata_optimization.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/312-ixp4xx_pata_optimization.patch
@ -0,0 +1,137 @@
+--- a/drivers/ata/pata_ixp4xx_cf.c
+++ b/drivers/ata/pata_ixp4xx_cf.c
+@@ -24,17 +24,58 @@
+ #include <scsi/scsi_host.h>
+ 
+ #define DRV_NAME	"pata_ixp4xx_cf"
+-#define DRV_VERSION	"0.2"
+#define DRV_VERSION	"0.3"
+ 
+ static int ixp4xx_set_mode(struct ata_link *link, struct ata_device **error)
+ {
+ 	struct ata_device *dev;
+	struct ixp4xx_pata_data *data = link->ap->host->dev->platform_data;
+	unsigned int pio_mask;
+ 
+ 	ata_link_for_each_dev(dev, link) {
+    if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)){
+      pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03;
+      if (pio_mask & (1 << 1)){
+        pio_mask = 4;
+      }else{
+        pio_mask = 3;
+      }
+    }else{
+      pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8);
+    }
+		switch (pio_mask){
+			case 0:
+				ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n");
+				dev->pio_mode = XFER_PIO_0;
+				dev->xfer_mode = XFER_PIO_0;
+				*data->cs0_cfg = 0x8a473c03;
+			break;
+			case 1:
+				ata_dev_printk(dev, KERN_INFO, "configured for PIO1\n");
+				dev->pio_mode = XFER_PIO_1;
+				dev->xfer_mode = XFER_PIO_1;
+				*data->cs0_cfg = 0x86433c03;
+			break;
+			case 2:
+				ata_dev_printk(dev, KERN_INFO, "configured for PIO2\n");
+				dev->pio_mode = XFER_PIO_2;
+				dev->xfer_mode = XFER_PIO_2;
+				*data->cs0_cfg = 0x82413c03;
+			break;
+			case 3:
+				ata_dev_printk(dev, KERN_INFO, "configured for PIO3\n");
+				dev->pio_mode = XFER_PIO_3;
+				dev->xfer_mode = XFER_PIO_3;
+				*data->cs0_cfg = 0x80823c03;
+			break;
+			case 4:
+				ata_dev_printk(dev, KERN_INFO, "configured for PIO4\n");
+				dev->pio_mode = XFER_PIO_4;
+				dev->xfer_mode = XFER_PIO_4;
+				*data->cs0_cfg = 0x80403c03;
+			break;
+		}
+ 		if (ata_dev_enabled(dev)) {
+-			ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n");
+-			dev->pio_mode = XFER_PIO_0;
+-			dev->xfer_mode = XFER_PIO_0;
+ 			dev->xfer_shift = ATA_SHIFT_PIO;
+ 			dev->flags |= ATA_DFLAG_PIO;
+ 		}
+@@ -48,6 +89,7 @@ static unsigned int ixp4xx_mmio_data_xfe
+ 	unsigned int i;
+ 	unsigned int words = buflen >> 1;
+ 	u16 *buf16 = (u16 *) buf;
+	unsigned int pio_mask;
+ 	struct ata_port *ap = dev->link->ap;
+ 	void __iomem *mmio = ap->ioaddr.data_addr;
+ 	struct ixp4xx_pata_data *data = ap->host->dev->platform_data;
+@@ -55,8 +97,34 @@ static unsigned int ixp4xx_mmio_data_xfe
+ 	/* set the expansion bus in 16bit mode and restore
+ 	 * 8 bit mode after the transaction.
+ 	 */
+-	*data->cs0_cfg &= ~(0x01);
+-	udelay(100);
+	if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)){
+		pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03;
+		if (pio_mask & (1 << 1)){
+			pio_mask = 4;
+		}else{
+			pio_mask = 3;
+		}
+	}else{
+		pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8);
+	}
+	switch (pio_mask){
+		case 0:
+			*data->cs0_cfg = 0xa9643c42;
+		break;
+		case 1:
+			*data->cs0_cfg = 0x85033c42;
+		break;
+		case 2:
+			*data->cs0_cfg = 0x80b23c42;
+		break;
+		case 3:
+			*data->cs0_cfg = 0x80823c42;
+		break;
+		case 4:
+			*data->cs0_cfg = 0x80403c42;
+		break;
+	}
+	udelay(5);
+ 
+ 	/* Transfer multiple of 2 bytes */
+ 	if (rw == READ)
+@@ -81,8 +149,24 @@ static unsigned int ixp4xx_mmio_data_xfe
+ 		words++;
+ 	}
+ 
+-	udelay(100);
+-	*data->cs0_cfg |= 0x01;
+	udelay(5);
+	switch (pio_mask){
+		case 0:
+			*data->cs0_cfg = 0x8a473c03;
+		break;
+		case 1:
+			*data->cs0_cfg = 0x86433c03;
+		break;
+		case 2:
+			*data->cs0_cfg = 0x82413c03;
+		break;
+		case 3:
+			*data->cs0_cfg = 0x80823c03;
+		break;
+		case 4:
+			*data->cs0_cfg = 0x80403c03;
+		break;
+	}
+ 
+ 	return words << 1;
+ }
--- a/target/linux/ixp4xx/patches-2.6.28/400-dmabounce.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/400-dmabounce.patch
@ -0,0 +1,27 @@
+--- a/arch/arm/common/dmabounce.c
+++ b/arch/arm/common/dmabounce.c
+@@ -117,6 +117,10 @@ alloc_safe_buffer(struct dmabounce_devic
+ 	} else if (size <= device_info->large.size) {
+ 		pool = &device_info->large;
+ 	} else {
+#ifdef CONFIG_DMABOUNCE_DEBUG
+		printk(KERN_INFO "A dma bounce buffer outside the pool size was requested. Requested size was 0x%08X\nThe calling code was :\n", size);
+		dump_stack();
+#endif
+ 		pool = NULL;
+ 	}
+ 
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -246,6 +246,11 @@ config MACH_MI424WR
+ 
+ comment "IXP4xx Options"
+ 
+config DMABOUNCE_DEBUG
+	bool "Enable DMABounce debuging"
+	default n
+	depends on DMABOUNCE
+
+ config IXP4XX_INDIRECT_PCI
+ 	bool "Use indirect PCI memory access"
+ 	depends on PCI
--- a/target/linux/ixp4xx/patches-2.6.28/401-avila_pci_dev.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/401-avila_pci_dev.patch
@ -0,0 +1,11 @@
+--- a/arch/arm/mach-ixp4xx/include/mach/avila.h
+++ b/arch/arm/mach-ixp4xx/include/mach/avila.h
+@@ -25,7 +25,7 @@
+ /*
+  * AVILA PCI IRQs
+  */
+-#define AVILA_PCI_MAX_DEV	4
+#define AVILA_PCI_MAX_DEV	6
+ #define LOFT_PCI_MAX_DEV    6
+ #define AVILA_PCI_IRQ_LINES	4
+ 
--- a/target/linux/ixp4xx/patches-2.6.28/500-usr8200_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.28/500-usr8200_support.patch
@ -0,0 +1,317 @@
+--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -97,6 +97,14 @@ config MACH_SIDEWINDER
+ 	  Engineering Sidewinder board. For more information on this
+ 	  platform, see http://www.adiengineering.com
+ 
+config MACH_USR8200
+	bool "USRobotics USR8200"
+	select PCI
+	help
+	  Say 'Y' here if you want your kernel to support the USRobotics
+	  USR8200 router board. For more information on this platform, see
+	  http://openwrt.org
+
+ config MACH_COMPEX
+ 	bool "Compex WP18 / NP18A"
+ 	select PCI
+--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -25,6 +25,7 @@ obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt
+ obj-pci-$(CONFIG_MACH_AP1000)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_TW5334)		+= tw5334-pci.o
+ obj-pci-$(CONFIG_MACH_MI424WR)		+= mi424wr-pci.o
+obj-pci-$(CONFIG_MACH_USR8200)		+= usr8200-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -48,6 +49,7 @@ obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv
+ obj-$(CONFIG_MACH_AP1000)	+= ap1000-setup.o
+ obj-$(CONFIG_MACH_TW5334)	+= tw5334-setup.o
+ obj-$(CONFIG_MACH_MI424WR)	+= mi424wr-setup.o
+obj-$(CONFIG_MACH_USR8200)	+= usr8200-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/usr8200-pci.c
+@@ -0,0 +1,78 @@
+/*
+ * arch/arch/mach-ixp4xx/usr8200-pci.c
+ *
+ * PCI setup routines for USRobotics USR8200
+ *
+ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org>
+ *
+ * based on pronghorn-pci.c
+ * 	Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * based on coyote-pci.c:
+ *	Copyright (C) 2002 Jungo Software Technologies.
+ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Peter Denison <openwrt@marshadder.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+
+#include <asm/mach/pci.h>
+
+void __init usr8200_pci_preinit(void)
+{
+	set_irq_type(IRQ_IXP4XX_GPIO7, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
+
+	ixp4xx_pci_preinit();
+}
+
+static int __init usr8200_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot == 14)
+		return IRQ_IXP4XX_GPIO7;
+	else if (slot == 15)
+		return IRQ_IXP4XX_GPIO8;
+	else if (slot == 16) {
+		if (pin == 1)
+			return IRQ_IXP4XX_GPIO11;
+		else if (pin == 2)
+			return IRQ_IXP4XX_GPIO10;
+		else if (pin == 3)
+			return IRQ_IXP4XX_GPIO9;
+		else
+			return -1;
+	} else
+		return -1;
+}
+
+struct hw_pci usr8200_pci __initdata = {
+	.nr_controllers	= 1,
+	.preinit	= usr8200_pci_preinit,
+	.swizzle	= pci_std_swizzle,
+	.setup		= ixp4xx_setup,
+	.scan		= ixp4xx_scan_bus,
+	.map_irq	= usr8200_map_irq,
+};
+
+int __init usr8200_pci_init(void)
+{
+	if (machine_is_usr8200())
+		pci_common_init(&usr8200_pci);
+	return 0;
+}
+
+subsys_initcall(usr8200_pci_init);
+--- /dev/null
+++ b/arch/arm/mach-ixp4xx/usr8200-setup.c
+@@ -0,0 +1,187 @@
+/*
+ * arch/arm/mach-ixp4xx/usr8200-setup.c
+ *
+ * Board setup for the USRobotics USR8200
+ *
+ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org>
+ *
+ * based on pronghorn-setup.c:
+ * 	Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * based on coyote-setup.c:
+ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Peter Denison <openwrt@marshadder.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/memory.h>
+#include <linux/i2c-gpio.h>
+#include <linux/leds.h>
+
+#include <asm/setup.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data usr8200_flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource usr8200_flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device usr8200_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &usr8200_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &usr8200_flash_resource,
+};
+
+static struct resource usr8200_uart_resources [] = {
+	{
+		.start		= IXP4XX_UART2_BASE_PHYS,
+		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM
+	},
+	{
+		.start		= IXP4XX_UART1_BASE_PHYS,
+		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM
+	}
+};
+
+static struct plat_serial8250_port usr8200_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device usr8200_uart = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM,
+	.dev		= {
+		.platform_data	= usr8200_uart_data,
+	},
+	.num_resources	= 2,
+	.resource	= usr8200_uart_resources,
+};
+
+/*
+static struct i2c_gpio_platform_data usr8200_i2c_gpio_data = {
+	.sda_pin	= 9,
+	.scl_pin	= 10,
+};
+
+static struct platform_device usr8200_i2c_gpio = {
+	.name		= "i2c-gpio",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &usr8200_i2c_gpio_data,
+	},
+};
+
+static struct gpio_led usr8200_led_pin[] = {
+	{
+		.name		= "usr8200:green:status",
+		.gpio		= 7,
+	}
+};
+
+static struct gpio_led_platform_data usr8200_led_data = {
+	.num_leds		= 1,
+	.leds			= usr8200_led_pin,
+};
+
+static struct platform_device usr8200_led = {
+	.name			= "leds-gpio",
+	.id			= -1,
+	.dev.platform_data	= &usr8200_led_data,
+};
+*/
+
+static struct eth_plat_info usr8200_plat_eth[] = {
+	{
+		.phy		= 16,
+		.rxq		= 4,
+		.txreadyq	= 21,
+	}, {
+		.phy		= 9,
+		.rxq		= 3,
+		.txreadyq	= 20,
+	}
+};
+
+static struct platform_device usr8200_eth[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= usr8200_plat_eth,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= usr8200_plat_eth + 1,
+	}
+};
+
+static struct platform_device *usr8200_devices[] __initdata = {
+	&usr8200_flash,
+	&usr8200_uart,
+/*	&usr8200_led,
+	&usr8200_i2c_gpio, */
+	&usr8200_eth[0],
+	&usr8200_eth[1],
+};
+
+static void __init usr8200_init(void)
+{
+	ixp4xx_sys_init();
+
+	usr8200_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	usr8200_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_64M - 1;
+
+	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+	platform_add_devices(usr8200_devices, ARRAY_SIZE(usr8200_devices));
+}
+
+MACHINE_START(USR8200, "USRobotics USR8200")
+	/* Maintainer: Peter Denison <openwrt@marshadder.org> */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= usr8200_init,
+MACHINE_END
+--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+@@ -43,7 +43,7 @@ static __inline__ void __arch_decomp_set
+ 	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+ 			 machine_is_gateway7001() || machine_is_wg302v2() ||
+ 			 machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
+-			 machine_is_tw5334())
+			 machine_is_tw5334() || machine_is_usr8200())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;