bcm63xx: add support for linux 3.8

Based on 3.8-rc6

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 35482

target/linux/brcm63xx/config-3.8

@@ -0,0 +1,182 @@
+CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
+CONFIG_ARCH_DISCARD_MEMBLOCK=y
+CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_AUDIT=y
+CONFIG_AUDIT_GENERIC=y
+CONFIG_B53=y
+CONFIG_B53_MMAP_DRIVER=y
+CONFIG_B53_PHY_DRIVER=y
+CONFIG_B53_PHY_FIXUP=y
+CONFIG_B53_SPI_DRIVER=y
+CONFIG_BCM63XX=y
+CONFIG_BCM63XX_CPU_6328=y
+CONFIG_BCM63XX_CPU_6338=y
+CONFIG_BCM63XX_CPU_6345=y
+CONFIG_BCM63XX_CPU_6348=y
+CONFIG_BCM63XX_CPU_6358=y
+CONFIG_BCM63XX_CPU_6362=y
+CONFIG_BCM63XX_CPU_6368=y
+CONFIG_BCM63XX_EHCI=y
+CONFIG_BCM63XX_ENET=y
+CONFIG_BCM63XX_OHCI=y
+CONFIG_BCM63XX_PHY=y
+CONFIG_BCM63XX_WDT=y
+CONFIG_BOARD_BCM963XX=y
+# CONFIG_BOARD_LIVEBOX is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_CEVT_R4K=y
+CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200"
+CONFIG_CMDLINE_BOOL=y
+# CONFIG_CMDLINE_OVERRIDE is not set
+CONFIG_CPU_BIG_ENDIAN=y
+CONFIG_CPU_GENERIC_DUMP_TLB=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+CONFIG_CPU_MIPSR1=y
+CONFIG_CPU_R4K_CACHE_TLB=y
+CONFIG_CPU_R4K_FPU=y
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_CRAMFS=y
+CONFIG_CSRC_R4K=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_74X164=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HAMRADIO is not set
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_GENERIC_HARDIRQS=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IRQ_WORK=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_BCM63XX=y
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+CONFIG_IMAGE_CMDLINE_HACK=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_IRQ_CPU=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_KEXEC=y
+CONFIG_LEDS_GPIO=y
+CONFIG_M25PXX_USE_FAST_READ=y
+CONFIG_MDIO_BOARDINFO=y
+CONFIG_MIPS=y
+# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+# CONFIG_MIPS_MACHINE is not set
+CONFIG_MIPS_MT_DISABLED=y
+# CONFIG_MIPS_SEAD3 is not set
+CONFIG_MODULES_USE_ELF_REL=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MTD_BCM63XX_PARTS=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_BE_BYTE_SWAP=y
+# CONFIG_MTD_CFI_GEOMETRY is not set
+# CONFIG_MTD_CFI_NOSWAP is not set
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_REDBOOT_PARTS=y
+CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_PCI=y
+# CONFIG_PCIEAER is not set
+CONFIG_PCIEPORTBUS=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PERCPU_RWSEM=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PHYLIB=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
+# CONFIG_PREEMPT_RCU is not set
+CONFIG_RELAY=y
+CONFIG_RTL8366_SMI=y
+CONFIG_RTL8367_PHY=y
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIAL_BCM63XX=y
+CONFIG_SERIAL_BCM63XX_CONSOLE=y
+CONFIG_SPI=y
+CONFIG_SPI_BCM63XX=y
+CONFIG_SPI_BCM63XX_HSSPI=y
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_GPIO=y
+CONFIG_SPI_MASTER=y
+CONFIG_SQUASHFS_EMBEDDED=y
+CONFIG_SSB=y
+CONFIG_SSB_B43_PCI_BRIDGE=y
+CONFIG_SSB_BLOCKIO=y
+# CONFIG_SSB_DRIVER_MIPS is not set
+CONFIG_SSB_DRIVER_PCICORE=y
+CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
+CONFIG_SSB_PCIHOST=y
+CONFIG_SSB_PCIHOST_POSSIBLE=y
+CONFIG_SSB_SPROM=y
+CONFIG_SWAP_IO_SPACE=y
+CONFIG_SWCONFIG=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_UIDGID_CONVERTED=y
+CONFIG_USB_ARCH_HAS_XHCI=y
+# CONFIG_USB_HCD_SSB is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_ZONE_DMA_FLAG=0

target/linux/brcm63xx/patches-3.8/106-spi-bcm63xx-reject-transfers-unable-to-transfer.patch

@@ -0,0 +1,162 @@
+From 243970ea035623f70431a80ece802f572cd446be Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jogo@openwrt.org>
+Date: Sun, 9 Dec 2012 00:10:00 +0100
+Subject: [PATCH V2 1/2] spi/bcm63xx: reject transfers unable to transfer
+
+The hardware does not support keeping CS asserted after sending one
+FIFO buffer worth of data, so reject transfers requiring CS being kept
+asserted, either between transers or for a certain time after it,
+or exceeding the FIFO size.
+
+Signed-off-by: Jonas Gorski <jogo@openwrt.org>
+---
+ drivers/spi/spi-bcm63xx.c |   91 +++++++++++++++++++++------------------------
+ 1 file changed, 42 insertions(+), 49 deletions(-)
+
+--- a/drivers/spi/spi-bcm63xx.c
++++ b/drivers/spi/spi-bcm63xx.c
+@@ -49,16 +49,10 @@ struct bcm63xx_spi {
+ 	unsigned int		msg_type_shift;
+ 	unsigned int		msg_ctl_width;
+ 
+-	/* Data buffers */
+-	const unsigned char	*tx_ptr;
+-	unsigned char		*rx_ptr;
+-
+ 	/* data iomem */
+ 	u8 __iomem		*tx_io;
+ 	const u8 __iomem	*rx_io;
+ 
+-	int			remaining_bytes;
+-
+ 	struct clk		*clk;
+ 	struct platform_device	*pdev;
+ };
+@@ -175,24 +169,13 @@ static int bcm63xx_spi_setup(struct spi_
+ 	return 0;
+ }
+ 
+-/* Fill the TX FIFO with as many bytes as possible */
+-static void bcm63xx_spi_fill_tx_fifo(struct bcm63xx_spi *bs)
+-{
+-	u8 size;
+-
+-	/* Fill the Tx FIFO with as many bytes as possible */
+-	size = bs->remaining_bytes < bs->fifo_size ? bs->remaining_bytes :
+-		bs->fifo_size;
+-	memcpy_toio(bs->tx_io, bs->tx_ptr, size);
+-	bs->remaining_bytes -= size;
+-}
+-
+-static unsigned int bcm63xx_txrx_bufs(struct spi_device *spi,
+-					struct spi_transfer *t)
++static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
+ {
+ 	struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
+ 	u16 msg_ctl;
+ 	u16 cmd;
++	u8 rx_tail;
++	unsigned int timeout = 0;
+ 
+ 	/* Disable the CMD_DONE interrupt */
+ 	bcm_spi_writeb(bs, 0, SPI_INT_MASK);
+@@ -200,14 +183,8 @@ static unsigned int bcm63xx_txrx_bufs(st
+ 	dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
+ 		t->tx_buf, t->rx_buf, t->len);
+ 
+-	/* Transmitter is inhibited */
+-	bs->tx_ptr = t->tx_buf;
+-	bs->rx_ptr = t->rx_buf;
+-
+-	if (t->tx_buf) {
+-		bs->remaining_bytes = t->len;
+-		bcm63xx_spi_fill_tx_fifo(bs);
+-	}
++	if (t->tx_buf)
++		memcpy_toio(bs->tx_io, t->tx_buf, t->len);
+ 
+ 	init_completion(&bs->done);
+ 
+@@ -239,7 +216,18 @@ static unsigned int bcm63xx_txrx_bufs(st
+ 	/* Enable the CMD_DONE interrupt */
+ 	bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK);
+ 
+-	return t->len - bs->remaining_bytes;
++	timeout = wait_for_completion_timeout(&bs->done, HZ);
++	if (!timeout)
++		return -ETIMEDOUT;
++
++	/* read out all data */
++	rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
++
++	/* Read out all the data */
++	if (rx_tail)
++		memcpy_fromio(t->rx_ptr, bs->rx_io, rx_tail);
++
++	return 0;
+ }
+ 
+ static int bcm63xx_spi_prepare_transfer(struct spi_master *master)
+@@ -267,36 +255,41 @@ static int bcm63xx_spi_transfer_one(stru
+ 	struct spi_transfer *t;
+ 	struct spi_device *spi = m->spi;
+ 	int status = 0;
+-	unsigned int timeout = 0;
+ 
+ 	list_for_each_entry(t, &m->transfers, transfer_list) {
+-		unsigned int len = t->len;
+-		u8 rx_tail;
+-
+ 		status = bcm63xx_spi_check_transfer(spi, t);
+ 		if (status < 0)
+ 			goto exit;
+ 
++		/* we can only transfer one fifo worth of data */
++		if (t->len > bs->fifo_size) {
++			dev_err(&spi->dev, "unable to do transfers larger than FIFO size (%i > %i)\n",
++				t->len, bs->fifo_size);
++			status = -EINVAL;
++			goto exit;
++		}
++
++		/* CS will be deasserted directly after transfer */
++		if (t->delay_usecs) {
++			dev_err(&spi->dev, "unable to keep CS asserted after transfer\n");
++			status = -EINVAL;
++			goto exit;
++		}
++
++		if (!t->cs_change &&
++		    !list_is_last(&t->transfer_list, &m->transfers)) {
++			dev_err(&spi->dev, "unable to keep CS asserted between transfers\n");
++			status = -EINVAL;
++			goto exit;
++		}
++
+ 		/* configure adapter for a new transfer */
+ 		bcm63xx_spi_setup_transfer(spi, t);
+ 
+-		while (len) {
+-			/* send the data */
+-			len -= bcm63xx_txrx_bufs(spi, t);
+-
+-			timeout = wait_for_completion_timeout(&bs->done, HZ);
+-			if (!timeout) {
+-				status = -ETIMEDOUT;
+-				goto exit;
+-			}
+-
+-			/* read out all data */
+-			rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
+-
+-			/* Read out all the data */
+-			if (rx_tail)
+-				memcpy_fromio(bs->rx_ptr, bs->rx_io, rx_tail);
+-		}
++		/* send the data */
++		status = bcm63xx_txrx_bufs(spi, t);
++		if (status)
++			goto exit;
+ 
+ 		m->actual_length += t->len;
+ 	}

target/linux/brcm63xx/patches-3.8/107-spi-bcm63xx-fix-multi-transfer-messages.patch

@@ -0,0 +1,240 @@
+From 725e81d507b1098cd275d4e3333c77c4b750fa79 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jogo@openwrt.org>
+Date: Sun, 9 Dec 2012 01:53:05 +0100
+Subject: [PATCH V2 2/2] spi/bcm63xx: work around inability to keep CS up
+
+This SPI controller does not support keeping CS asserted after sending
+a transfer.
+Since messages expected on this SPI controller are rather short, we can
+work around it for normal use cases by sending all transfers at once in
+a big full duplex stream.
+
+This means that we cannot change the speed between transfers if they
+require CS to be kept asserted, but these would have been rejected
+before anyway because of the inability of keeping CS asserted.
+
+Signed-off-by: Jonas Gorski <jogo@openwrt.org>
+---
+V1 -> V2:
+ * split out rejection logic into separate patch
+ * fixed return type of bcm63xx_txrx_bufs()
+ * slightly reworked bcm63xx_txrx_bufs, obsoleting one local variable
+
+ drivers/spi/spi-bcm63xx.c |  134 +++++++++++++++++++++++++++++++++++----------
+ 1 file changed, 106 insertions(+), 28 deletions(-)
+
+--- a/drivers/spi/spi-bcm63xx.c
++++ b/drivers/spi/spi-bcm63xx.c
+@@ -37,6 +37,8 @@
+ 
+ #define PFX		KBUILD_MODNAME
+ 
++#define BCM63XX_SPI_MAX_PREPEND		15
++
+ struct bcm63xx_spi {
+ 	struct completion	done;
+ 
+@@ -169,13 +171,17 @@ static int bcm63xx_spi_setup(struct spi_
+ 	return 0;
+ }
+ 
+-static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
++static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *first,
++				unsigned int num_transfers)
+ {
+ 	struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
+ 	u16 msg_ctl;
+ 	u16 cmd;
+ 	u8 rx_tail;
+-	unsigned int timeout = 0;
++	unsigned int i, timeout = 0, prepend_len = 0, len = 0;
++	struct spi_transfer *t = first;
++	bool do_rx = false;
++	bool do_tx = false;
+ 
+ 	/* Disable the CMD_DONE interrupt */
+ 	bcm_spi_writeb(bs, 0, SPI_INT_MASK);
+@@ -183,19 +189,45 @@ static int bcm63xx_txrx_bufs(struct spi_
+ 	dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
+ 		t->tx_buf, t->rx_buf, t->len);
+ 
+-	if (t->tx_buf)
+-		memcpy_toio(bs->tx_io, t->tx_buf, t->len);
++	if (num_transfers > 1 && t->tx_buf && t->len <= BCM63XX_SPI_MAX_PREPEND)
++		prepend_len = t->len;
++
++	/* prepare the buffer */
++	for (i = 0; i < num_transfers; i++) {
++		if (t->tx_buf) {
++			do_tx = true;
++			memcpy_toio(bs->tx_io + len, t->tx_buf, t->len);
++
++			/* don't prepend more than one tx */
++			if (t != first)
++				prepend_len = 0;
++		}
++
++		if (t->rx_buf) {
++			do_rx = true;
++			/* prepend is half-duplex write only */
++			if (t == first)
++				prepend_len = 0;
++		}
++
++		len += t->len;
++
++		t = list_entry(t->transfer_list.next, struct spi_transfer,
++			       transfer_list);
++	}
++
++	len -= prepend_len;
+ 
+ 	init_completion(&bs->done);
+ 
+ 	/* Fill in the Message control register */
+-	msg_ctl = (t->len << SPI_BYTE_CNT_SHIFT);
++	msg_ctl = (len << SPI_BYTE_CNT_SHIFT);
+ 
+-	if (t->rx_buf && t->tx_buf)
++	if (do_rx && do_tx && prepend_len == 0)
+ 		msg_ctl |= (SPI_FD_RW << bs->msg_type_shift);
+-	else if (t->rx_buf)
++	else if (do_rx)
+ 		msg_ctl |= (SPI_HD_R << bs->msg_type_shift);
+-	else if (t->tx_buf)
++	else if (do_tx)
+ 		msg_ctl |= (SPI_HD_W << bs->msg_type_shift);
+ 
+ 	switch (bs->msg_ctl_width) {
+@@ -209,7 +241,7 @@ static int bcm63xx_txrx_bufs(struct spi_
+ 
+ 	/* Issue the transfer */
+ 	cmd = SPI_CMD_START_IMMEDIATE;
+-	cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
++	cmd |= (prepend_len << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
+ 	cmd |= (spi->chip_select << SPI_CMD_DEVICE_ID_SHIFT);
+ 	bcm_spi_writew(bs, cmd, SPI_CMD);
+ 
+@@ -223,9 +255,25 @@ static int bcm63xx_txrx_bufs(struct spi_
+ 	/* read out all data */
+ 	rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
+ 
++	if (do_rx && rx_tail != len)
++		return -EIO;
++
++	if (!rx_tail)
++		return 0;
++
++	len = 0;
++	t = first;
+ 	/* Read out all the data */
+-	if (rx_tail)
+-		memcpy_fromio(t->rx_ptr, bs->rx_io, rx_tail);
++	for (i = 0; i < num_transfers; i++) {
++		if (t->rx_buf)
++			memcpy_fromio(t->rx_buf, bs->rx_io + len, t->len);
++
++		if (t != first || prepend_len == 0)
++			len += t->len;
++
++		t = list_entry(t->transfer_list.next, struct spi_transfer,
++			       transfer_list);
++	}
+ 
+ 	return 0;
+ }
+@@ -252,46 +300,76 @@ static int bcm63xx_spi_transfer_one(stru
+ 					struct spi_message *m)
+ {
+ 	struct bcm63xx_spi *bs = spi_master_get_devdata(master);
+-	struct spi_transfer *t;
++	struct spi_transfer *t, *first = NULL;
+ 	struct spi_device *spi = m->spi;
+ 	int status = 0;
++	unsigned int n_transfers = 0, total_len = 0;
++	bool can_use_prepend = false;
+ 
++	/*
++	 * This SPI controller does not support keeping CS active after a
++	 * transfer.
++	 * Work around this by merging as many transfers we can into one big
++	 * full-duplex transfers.
++	 */
+ 	list_for_each_entry(t, &m->transfers, transfer_list) {
+ 		status = bcm63xx_spi_check_transfer(spi, t);
+ 		if (status < 0)
+ 			goto exit;
+ 
++		if (!first)
++			first = t;
++
++		n_transfers++;
++		total_len += t->len;
++
++		if (n_transfers == 2 && !first->rx_buf && !t->tx_buf &&
++		    first->len <= BCM63XX_SPI_MAX_PREPEND)
++			can_use_prepend = true;
++		else if (can_use_prepend && t->tx_buf)
++			can_use_prepend = false;
++
+ 		/* we can only transfer one fifo worth of data */
+-		if (t->len > bs->fifo_size) {
++		if ((can_use_prepend &&
++		     total_len > (bs->fifo_size + BCM63XX_SPI_MAX_PREPEND)) ||
++		    (!can_use_prepend && total_len > bs->fifo_size)) {
+ 			dev_err(&spi->dev, "unable to do transfers larger than FIFO size (%i > %i)\n",
+-				t->len, bs->fifo_size);
++				total_len, bs->fifo_size);
+ 			status = -EINVAL;
+ 			goto exit;
+ 		}
+ 
+-		/* CS will be deasserted directly after transfer */
+-		if (t->delay_usecs) {
+-			dev_err(&spi->dev, "unable to keep CS asserted after transfer\n");
++		/* all combined transfers have to have the same speed */
++		if (t->speed_hz != first->speed_hz) {
++			dev_err(&spi->dev, "unable to change speed between transfers\n");
+ 			status = -EINVAL;
+ 			goto exit;
+ 		}
+ 
+-		if (!t->cs_change &&
+-		    !list_is_last(&t->transfer_list, &m->transfers)) {
+-			dev_err(&spi->dev, "unable to keep CS asserted between transfers\n");
++		/* CS will be deasserted directly after transfer */
++		if (t->delay_usecs) {
++			dev_err(&spi->dev, "unable to keep CS asserted after transfer\n");
+ 			status = -EINVAL;
+ 			goto exit;
+ 		}
+ 
+-		/* configure adapter for a new transfer */
+-		bcm63xx_spi_setup_transfer(spi, t);
+-
+-		/* send the data */
+-		status = bcm63xx_txrx_bufs(spi, t);
+-		if (status)
+-			goto exit;
+-
+-		m->actual_length += t->len;
++		if (t->cs_change ||
++		    list_is_last(&t->transfer_list, &m->transfers)) {
++			/* configure adapter for a new transfer */
++			bcm63xx_spi_setup_transfer(spi, first);
++
++			/* send the data */
++			status = bcm63xx_txrx_bufs(spi, first, n_transfers);
++			if (status)
++				goto exit;
++
++			m->actual_length += total_len;
++
++			first = NULL;
++			n_transfers = 0;
++			total_len = 0;
++			can_use_prepend = false;
++		}
+ 	}
+ exit:
+ 	m->status = status;

target/linux/brcm63xx/patches-3.8/108-MIPS-BCM63XX-add-USB-host-clock-enable-delay.patch

@@ -0,0 +1,28 @@
+From 80a2f983e9f44dbc3e01ae31c62d877846a7f791 Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:19 +0100
+Subject: [PATCH 01/11] MIPS: BCM63XX: add USB host clock enable delay
+
+Knowledge of the clock setup delay should remain at the clock level (so
+it can be clock specific and CPU specific). Add the 100 milliseconds
+required clock delay for the USB host clock when it gets enabled.
+
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/clk.c |    5 +++++
+ 1 file changed, 5 insertions(+)
+
+--- a/arch/mips/bcm63xx/clk.c
++++ b/arch/mips/bcm63xx/clk.c
+@@ -162,6 +162,11 @@ static void usbh_set(struct clk *clk, in
+ 		bcm_hwclock_set(CKCTL_6348_USBH_EN, enable);
+ 	else if (BCMCPU_IS_6368())
+ 		bcm_hwclock_set(CKCTL_6368_USBH_EN, enable);
++	else
++		return;
++
++	if (enable)
++		msleep(100);
+ }
+ 
+ static struct clk clk_usbh = {

target/linux/brcm63xx/patches-3.8/109-MIPS-BCM63XX-add-USB-device-clock-enable-delay-to-cl.patch

@@ -0,0 +1,41 @@
+From 8e9bf528a122741f0171b89c297b63041116d704 Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:20 +0100
+Subject: [PATCH 02/11] MIPS: BCM63XX: add USB device clock enable delay to
+ clock code
+
+This patch adds the required 10 micro seconds delay to the USB device
+clock enable operation. Put this where the correct clock knowledege is,
+which is in the clock code, and remove this delay from the bcm63xx_udc
+gadget driver where it was before.
+
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/clk.c          |    5 +++++
+ drivers/usb/gadget/bcm63xx_udc.c |    1 -
+ 2 files changed, 5 insertions(+), 1 deletion(-)
+
+--- a/arch/mips/bcm63xx/clk.c
++++ b/arch/mips/bcm63xx/clk.c
+@@ -182,6 +182,11 @@ static void usbd_set(struct clk *clk, in
+ 		bcm_hwclock_set(CKCTL_6328_USBD_EN, enable);
+ 	else if (BCMCPU_IS_6368())
+ 		bcm_hwclock_set(CKCTL_6368_USBD_EN, enable);
++	else
++		return;
++
++	if (enable)
++		udelay(10);
+ }
+ 
+ static struct clk clk_usbd = {
+--- a/drivers/usb/gadget/bcm63xx_udc.c
++++ b/drivers/usb/gadget/bcm63xx_udc.c
+@@ -386,7 +386,6 @@ static inline void set_clocks(struct bcm
+ 	if (is_enabled) {
+ 		clk_enable(udc->usbh_clk);
+ 		clk_enable(udc->usbd_clk);
+-		udelay(10);
+ 	} else {
+ 		clk_disable(udc->usbd_clk);
+ 		clk_disable(udc->usbh_clk);

target/linux/brcm63xx/patches-3.8/110-MIPS-BCM63XX-move-code-touching-the-USB-private-regi.patch

@@ -0,0 +1,151 @@
+From ac9b0b574d54be28b300bf99ffe092a2c589484f Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:21 +0100
+Subject: [PATCH 03/11] MIPS: BCM63XX: move code touching the USB private
+ register
+
+This patch moves the code touching the USB private register in the
+bcm63xx USB gadget driver to arch/mips/bcm63xx/usb-common.c in
+preparation for adding support for OHCI and EHCI host controllers which
+will also touch the USB private register.
+
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/Makefile                         |    2 +-
+ arch/mips/bcm63xx/usb-common.c                     |   53 ++++++++++++++++++++
+ .../include/asm/mach-bcm63xx/bcm63xx_usb_priv.h    |    9 ++++
+ drivers/usb/gadget/bcm63xx_udc.c                   |   27 ++--------
+ 4 files changed, 67 insertions(+), 24 deletions(-)
+ create mode 100644 arch/mips/bcm63xx/usb-common.c
+ create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h
+
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -1,7 +1,7 @@
+ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \
+ 		   setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
+ 		   dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \
+-		   dev-usb-usbd.o
++		   dev-usb-usbd.o usb-common.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- /dev/null
++++ b/arch/mips/bcm63xx/usb-common.c
+@@ -0,0 +1,53 @@
++/*
++ * Broadcom BCM63xx common USB device configuration code
++ *
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2012 Kevin Cernekee <cernekee@gmail.com>
++ * Copyright (C) 2012 Broadcom Corporation
++ *
++ */
++#include <linux/export.h>
++
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_regs.h>
++#include <bcm63xx_io.h>
++#include <bcm63xx_usb_priv.h>
++
++void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device)
++{
++	u32 val;
++
++	val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
++	if (is_device) {
++		val |= (portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT);
++		val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
++	} else {
++		val &= ~(portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT);
++		val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
++	}
++	bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
++
++	val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
++	if (is_device)
++		val |= USBH_PRIV_SWAP_USBD_MASK;
++	else
++		val &= ~USBH_PRIV_SWAP_USBD_MASK;
++	bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG);
++}
++EXPORT_SYMBOL(bcm63xx_usb_priv_select_phy_mode);
++
++void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on)
++{
++	u32 val;
++
++	val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
++	if (is_on)
++		val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
++	else
++		val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
++	bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
++}
++EXPORT_SYMBOL(bcm63xx_usb_priv_select_pullup);
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h
+@@ -0,0 +1,9 @@
++#ifndef BCM63XX_USB_PRIV_H_
++#define BCM63XX_USB_PRIV_H_
++
++#include <linux/types.h>
++
++void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device);
++void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on);
++
++#endif /* BCM63XX_USB_PRIV_H_ */
+--- a/drivers/usb/gadget/bcm63xx_udc.c
++++ b/drivers/usb/gadget/bcm63xx_udc.c
+@@ -41,6 +41,7 @@
+ #include <bcm63xx_dev_usb_usbd.h>
+ #include <bcm63xx_io.h>
+ #include <bcm63xx_regs.h>
++#include <bcm63xx_usb_priv.h>
+ 
+ #define DRV_MODULE_NAME		"bcm63xx_udc"
+ 
+@@ -863,22 +864,7 @@ static void bcm63xx_select_phy_mode(stru
+ 		bcm_gpio_writel(val, GPIO_PINMUX_OTHR_REG);
+ 	}
+ 
+-	val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
+-	if (is_device) {
+-		val |= (portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT);
+-		val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
+-	} else {
+-		val &= ~(portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT);
+-		val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
+-	}
+-	bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
+-
+-	val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
+-	if (is_device)
+-		val |= USBH_PRIV_SWAP_USBD_MASK;
+-	else
+-		val &= ~USBH_PRIV_SWAP_USBD_MASK;
+-	bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG);
++	bcm63xx_usb_priv_select_phy_mode(portmask, is_device);
+ }
+ 
+ /**
+@@ -892,14 +878,9 @@ static void bcm63xx_select_phy_mode(stru
+  */
+ static void bcm63xx_select_pullup(struct bcm63xx_udc *udc, bool is_on)
+ {
+-	u32 val, portmask = BIT(udc->pd->port_no);
++	u32 portmask = BIT(udc->pd->port_no);
+ 
+-	val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
+-	if (is_on)
+-		val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
+-	else
+-		val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
+-	bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
++	bcm63xx_usb_priv_select_pullup(portmask, is_on);
+ }
+ 
+ /**

target/linux/brcm63xx/patches-3.8/111-MIPS-BCM63XX-add-OHCI-EHCI-configuration-bits-to-com.patch

@@ -0,0 +1,169 @@
+From 28758a9da77954ed323f86123ef448c6a563c037 Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:22 +0100
+Subject: [PATCH 04/11] MIPS: BCM63XX: add OHCI/EHCI configuration bits to
+ common USB code
+
+This patch updates the common USB code touching the USB private
+registers with the specific bits to properly enable OHCI and EHCI
+controllers on BCM63xx SoCs. As a result we now need to protect access
+to Read Modify Write sequences using a spinlock because we cannot
+guarantee that any of the exposed helper will not be called
+concurrently.
+
+Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/usb-common.c                     |   97 ++++++++++++++++++++
+ .../include/asm/mach-bcm63xx/bcm63xx_usb_priv.h    |    2 +
+ 2 files changed, 99 insertions(+)
+
+--- a/arch/mips/bcm63xx/usb-common.c
++++ b/arch/mips/bcm63xx/usb-common.c
+@@ -5,10 +5,12 @@
+  * License.  See the file "COPYING" in the main directory of this archive
+  * for more details.
+  *
++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+  * Copyright (C) 2012 Kevin Cernekee <cernekee@gmail.com>
+  * Copyright (C) 2012 Broadcom Corporation
+  *
+  */
++#include <linux/spinlock.h>
+ #include <linux/export.h>
+ 
+ #include <bcm63xx_cpu.h>
+@@ -16,9 +18,14 @@
+ #include <bcm63xx_io.h>
+ #include <bcm63xx_usb_priv.h>
+ 
++static DEFINE_SPINLOCK(usb_priv_reg_lock);
++
+ void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device)
+ {
+ 	u32 val;
++	unsigned long flags;
++
++	spin_lock_irqsave(&usb_priv_reg_lock, flags);
+ 
+ 	val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
+ 	if (is_device) {
+@@ -36,12 +43,17 @@ void bcm63xx_usb_priv_select_phy_mode(u3
+ 	else
+ 		val &= ~USBH_PRIV_SWAP_USBD_MASK;
+ 	bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG);
++
++	spin_unlock_irqrestore(&usb_priv_reg_lock, flags);
+ }
+ EXPORT_SYMBOL(bcm63xx_usb_priv_select_phy_mode);
+ 
+ void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on)
+ {
+ 	u32 val;
++	unsigned long flags;
++
++	spin_lock_irqsave(&usb_priv_reg_lock, flags);
+ 
+ 	val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
+ 	if (is_on)
+@@ -49,5 +61,90 @@ void bcm63xx_usb_priv_select_pullup(u32
+ 	else
+ 		val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
+ 	bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
++
++	spin_unlock_irqrestore(&usb_priv_reg_lock, flags);
+ }
+ EXPORT_SYMBOL(bcm63xx_usb_priv_select_pullup);
++
++/* The following array represents the meaning of the DESC/DATA
++ * endian swapping with respect to the CPU configured endianness
++ *
++ * DATA	ENDN	mmio	descriptor
++ * 0	0	BE	invalid
++ * 0	1	BE	LE
++ * 1	0	BE	BE
++ * 1	1	BE	invalid
++ *
++ * Since BCM63XX SoCs are configured to be in big-endian mode
++ * we want configuration at line 3.
++ */
++void bcm63xx_usb_priv_ohci_cfg_set(void)
++{
++	u32 reg;
++	unsigned long flags;
++
++	spin_lock_irqsave(&usb_priv_reg_lock, flags);
++
++	if (BCMCPU_IS_6348())
++		bcm_rset_writel(RSET_OHCI_PRIV, 0, OHCI_PRIV_REG);
++	else if (BCMCPU_IS_6358()) {
++		reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG);
++		reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK;
++		reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK;
++		bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG);
++		/*
++		 * The magic value comes for the original vendor BSP
++		 * and is needed for USB to work. Datasheet does not
++		 * help, so the magic value is used as-is.
++		 */
++		bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020,
++				USBH_PRIV_TEST_6358_REG);
++
++	} else if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) {
++		reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
++		reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK;
++		reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK;
++		bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG);
++
++		reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG);
++		reg |= USBH_PRIV_SETUP_IOC_MASK;
++		bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG);
++	}
++
++	spin_unlock_irqrestore(&usb_priv_reg_lock, flags);
++}
++
++void bcm63xx_usb_priv_ehci_cfg_set(void)
++{
++	u32 reg;
++	unsigned long flags;
++
++	spin_lock_irqsave(&usb_priv_reg_lock, flags);
++
++	if (BCMCPU_IS_6358()) {
++		reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG);
++		reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK;
++		reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK;
++		bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG);
++
++		/*
++		 * The magic value comes for the original vendor BSP
++		 * and is needed for USB to work. Datasheet does not
++		 * help, so the magic value is used as-is.
++		 */
++		bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020,
++				USBH_PRIV_TEST_6358_REG);
++
++	} else if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) {
++		reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
++		reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK;
++		reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK;
++		bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG);
++
++		reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG);
++		reg |= USBH_PRIV_SETUP_IOC_MASK;
++		bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG);
++	}
++
++	spin_unlock_irqrestore(&usb_priv_reg_lock, flags);
++}
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h
+@@ -5,5 +5,7 @@
+ 
+ void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device);
+ void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on);
++void bcm63xx_usb_priv_ohci_cfg_set(void);
++void bcm63xx_usb_priv_ehci_cfg_set(void);
+ 
+ #endif /* BCM63XX_USB_PRIV_H_ */

target/linux/brcm63xx/patches-3.8/112-MIPS-BCM63XX-introduce-BCM63XX_OHCI-configuration-sy.patch

@@ -0,0 +1,62 @@
+From 94ec618bd1a6b07fafbbfc9bcc54e7f9360ff9a0 Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:23 +0100
+Subject: [PATCH 05/11] MIPS: BCM63XX: introduce BCM63XX_OHCI configuration
+ symbol
+
+This configuration symbol can be used by CPUs supporting the on-chip
+OHCI controller, and ensures that all relevant OHCI-related
+configuration options are correctly selected. So far, OHCI support is
+available for the 6328, 6348, 6358 and 6358 SoCs.
+
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/Kconfig |   15 ++++++++++-----
+ 1 file changed, 10 insertions(+), 5 deletions(-)
+
+--- a/arch/mips/bcm63xx/Kconfig
++++ b/arch/mips/bcm63xx/Kconfig
+@@ -1,33 +1,38 @@
+ menu "CPU support"
+ 	depends on BCM63XX
+ 
++config BCM63XX_OHCI
++	bool
++	select USB_ARCH_HAS_OHCI
++	select USB_OHCI_BIG_ENDIAN_DESC if USB_OHCI_HCD
++	select USB_OHCI_BIG_ENDIAN_MMIO if USB_OHCI_HCD
++
+ config BCM63XX_CPU_6328
+ 	bool "support 6328 CPU"
+ 	select HW_HAS_PCI
++	select BCM63XX_OHCI
+ 
+ config BCM63XX_CPU_6338
+ 	bool "support 6338 CPU"
+ 	select HW_HAS_PCI
+-	select USB_ARCH_HAS_OHCI
+-	select USB_OHCI_BIG_ENDIAN_DESC
+-	select USB_OHCI_BIG_ENDIAN_MMIO
+ 
+ config BCM63XX_CPU_6345
+ 	bool "support 6345 CPU"
+-	select USB_OHCI_BIG_ENDIAN_DESC
+-	select USB_OHCI_BIG_ENDIAN_MMIO
+ 
+ config BCM63XX_CPU_6348
+ 	bool "support 6348 CPU"
+ 	select HW_HAS_PCI
++	select BCM63XX_OHCI
+ 
+ config BCM63XX_CPU_6358
+ 	bool "support 6358 CPU"
+ 	select HW_HAS_PCI
++	select BCM63XX_OHCI
+ 
+ config BCM63XX_CPU_6368
+ 	bool "support 6368 CPU"
+ 	select HW_HAS_PCI
++	select BCM63XX_OHCI
+ endmenu
+ 
+ source "arch/mips/bcm63xx/boards/Kconfig"

target/linux/brcm63xx/patches-3.8/113-MIPS-BCM63XX-add-support-for-the-on-chip-OHCI-contro.patch

@@ -0,0 +1,138 @@
+From 30d22baef255c99a12c4858ce4ab0d45f0d8c9ae Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:24 +0100
+Subject: [PATCH 06/11] MIPS: BCM63XX: add support for the on-chip OHCI
+ controller
+
+Broadcom BCM63XX SoCs include an on-chip OHCI controller which can be
+driven by the ohci-platform generic driver by using specific power
+on/off/suspend callback to manage clocks and hardware specific
+configuration.
+
+Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/Makefile                         |    2 +-
+ arch/mips/bcm63xx/dev-usb-ohci.c                   |   94 ++++++++++++++++++++
+ .../asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h        |    6 ++
+ 3 files changed, 101 insertions(+), 1 deletion(-)
+ create mode 100644 arch/mips/bcm63xx/dev-usb-ohci.c
+ create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
+
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -1,7 +1,7 @@
+ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \
+ 		   setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
+ 		   dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \
+-		   dev-usb-usbd.o usb-common.o
++		   dev-usb-ohci.o dev-usb-usbd.o usb-common.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- /dev/null
++++ b/arch/mips/bcm63xx/dev-usb-ohci.c
+@@ -0,0 +1,94 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
++ * Copyright (C) 2013 Florian Fainelli <florian@openwrt.org>
++ */
++
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++#include <linux/usb/ohci_pdriver.h>
++#include <linux/dma-mapping.h>
++#include <linux/clk.h>
++#include <linux/delay.h>
++
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_regs.h>
++#include <bcm63xx_io.h>
++#include <bcm63xx_usb_priv.h>
++#include <bcm63xx_dev_usb_ohci.h>
++
++static struct resource ohci_resources[] = {
++	{
++		.start		= -1, /* filled at runtime */
++		.end		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_MEM,
++	},
++	{
++		.start		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++static u64 ohci_dmamask = DMA_BIT_MASK(32);
++
++static struct clk *usb_host_clock;
++
++static int bcm63xx_ohci_power_on(struct platform_device *pdev)
++{
++	usb_host_clock = clk_get(&pdev->dev, "usbh");
++	if (IS_ERR_OR_NULL(usb_host_clock))
++		return -ENODEV;
++
++	clk_prepare_enable(usb_host_clock);
++
++	bcm63xx_usb_priv_ohci_cfg_set();
++
++	return 0;
++}
++
++static void bcm63xx_ohci_power_off(struct platform_device *pdev)
++{
++	if (!IS_ERR_OR_NULL(usb_host_clock)) {
++		clk_disable_unprepare(usb_host_clock);
++		clk_put(usb_host_clock);
++	}
++}
++
++static struct usb_ohci_pdata bcm63xx_ohci_pdata = {
++	.big_endian_desc	= 1,
++	.big_endian_mmio	= 1,
++	.no_big_frame_no	= 1,
++	.num_ports		= 1,
++	.power_on		= bcm63xx_ohci_power_on,
++	.power_off		= bcm63xx_ohci_power_off,
++	.power_suspend		= bcm63xx_ohci_power_off,
++};
++
++static struct platform_device bcm63xx_ohci_device = {
++	.name		= "ohci-platform",
++	.id		= -1,
++	.num_resources	= ARRAY_SIZE(ohci_resources),
++	.resource	= ohci_resources,
++	.dev		= {
++		.platform_data		= &bcm63xx_ohci_pdata,
++		.dma_mask		= &ohci_dmamask,
++		.coherent_dma_mask	= DMA_BIT_MASK(32),
++	},
++};
++
++int __init bcm63xx_ohci_register(void)
++{
++	if (BCMCPU_IS_6345() || BCMCPU_IS_6338())
++		return -ENODEV;
++
++	ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0);
++	ohci_resources[0].end = ohci_resources[0].start;
++	ohci_resources[0].end += RSET_OHCI_SIZE - 1;
++	ohci_resources[1].start = bcm63xx_get_irq_number(IRQ_OHCI0);
++
++	return platform_device_register(&bcm63xx_ohci_device);
++}
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
+@@ -0,0 +1,6 @@
++#ifndef BCM63XX_DEV_USB_OHCI_H_
++#define BCM63XX_DEV_USB_OHCI_H_
++
++int bcm63xx_ohci_register(void);
++
++#endif /* BCM63XX_DEV_USB_OHCI_H_ */

target/linux/brcm63xx/patches-3.8/114-MIPS-BCM63XX-register-OHCI-controller-if-board-enabl.patch

@@ -0,0 +1,36 @@
+From 33ef960aed15f9a98a2c51d8d794cd72418e0be4 Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:25 +0100
+Subject: [PATCH 07/11] MIPS: BCM63XX: register OHCI controller if board
+ enables it
+
+BCM63XX-based boards can control the registration of the OHCI controller
+by setting their has_ohci0 flag to 1. Handle this in the generic
+code dealing with board registration and call the actual helper to
+register the OHCI controller.
+
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c |    4 ++++
+ 1 file changed, 4 insertions(+)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -25,6 +25,7 @@
+ #include <bcm63xx_dev_flash.h>
+ #include <bcm63xx_dev_pcmcia.h>
+ #include <bcm63xx_dev_spi.h>
++#include <bcm63xx_dev_usb_ohci.h>
+ #include <bcm63xx_dev_usb_usbd.h>
+ #include <board_bcm963xx.h>
+ 
+@@ -851,6 +852,9 @@ int __init board_register_devices(void)
+ 	if (board.has_usbd)
+ 		bcm63xx_usbd_register(&board.usbd);
+ 
++	if (board.has_ohci0)
++		bcm63xx_ohci_register();
++
+ 	if (board.has_dsp)
+ 		bcm63xx_dsp_register(&board.dsp);
+ 

target/linux/brcm63xx/patches-3.8/115-MIPS-BCM63XX-introduce-BCM63XX_EHCI-configuration-sy.patch

@@ -0,0 +1,73 @@
+From 00da1683364e58c6430a4577123d01037f8faddc Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:26 +0100
+Subject: [PATCH 08/11] MIPS: BCM63XX: introduce BCM63XX_EHCI configuration
+ symbol
+
+This configuration symbol can be used by CPUs supporting the on-chip
+EHCI controller, and ensures that all relevant EHCI-related
+configuration options are selected. So far BCM6328, BCM6358 and BCM6368
+have an EHCI controller and do select this symbol. Update
+drivers/usb/host/Kconfig with BCM63XX to update direct unmet
+dependencies.
+
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/Kconfig |    9 +++++++++
+ drivers/usb/host/Kconfig  |    5 +++--
+ 2 files changed, 12 insertions(+), 2 deletions(-)
+
+--- a/arch/mips/bcm63xx/Kconfig
++++ b/arch/mips/bcm63xx/Kconfig
+@@ -7,10 +7,17 @@ config BCM63XX_OHCI
+ 	select USB_OHCI_BIG_ENDIAN_DESC if USB_OHCI_HCD
+ 	select USB_OHCI_BIG_ENDIAN_MMIO if USB_OHCI_HCD
+ 
++config BCM63XX_EHCI
++	bool
++	select USB_ARCH_HAS_EHCI
++	select USB_EHCI_BIG_ENDIAN_DESC if USB_EHCI_HCD
++	select USB_EHCI_BIG_ENDIAN_MMIO if USB_EHCI_HCD
++
+ config BCM63XX_CPU_6328
+ 	bool "support 6328 CPU"
+ 	select HW_HAS_PCI
+ 	select BCM63XX_OHCI
++	select BCM63XX_EHCI
+ 
+ config BCM63XX_CPU_6338
+ 	bool "support 6338 CPU"
+@@ -28,11 +35,13 @@ config BCM63XX_CPU_6358
+ 	bool "support 6358 CPU"
+ 	select HW_HAS_PCI
+ 	select BCM63XX_OHCI
++	select BCM63XX_EHCI
+ 
+ config BCM63XX_CPU_6368
+ 	bool "support 6368 CPU"
+ 	select HW_HAS_PCI
+ 	select BCM63XX_OHCI
++	select BCM63XX_EHCI
+ endmenu
+ 
+ source "arch/mips/bcm63xx/boards/Kconfig"
+--- a/drivers/usb/host/Kconfig
++++ b/drivers/usb/host/Kconfig
+@@ -115,14 +115,15 @@ config USB_EHCI_BIG_ENDIAN_MMIO
+ 	depends on USB_EHCI_HCD && (PPC_CELLEB || PPC_PS3 || 440EPX || \
+ 				    ARCH_IXP4XX || XPS_USB_HCD_XILINX || \
+ 				    PPC_MPC512x || CPU_CAVIUM_OCTEON || \
+-				    PMC_MSP || SPARC_LEON || MIPS_SEAD3)
++				    PMC_MSP || SPARC_LEON || MIPS_SEAD3 || \
++				    BCM63XX)
+ 	default y
+ 
+ config USB_EHCI_BIG_ENDIAN_DESC
+ 	bool
+ 	depends on USB_EHCI_HCD && (440EPX || ARCH_IXP4XX || XPS_USB_HCD_XILINX || \
+ 				    PPC_MPC512x || PMC_MSP || SPARC_LEON || \
+-				    MIPS_SEAD3)
++				    MIPS_SEAD3 || BCM63XX)
+ 	default y
+ 
+ config XPS_USB_HCD_XILINX

target/linux/brcm63xx/patches-3.8/116-MIPS-BCM63XX-add-support-for-the-on-chip-EHCI-contro.patch

@@ -0,0 +1,136 @@
+From e38f13bd6408769c0b565bb1079024f496eee121 Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:27 +0100
+Subject: [PATCH 09/11] MIPS: BCM63XX: add support for the on-chip EHCI
+ controller
+
+Broadcom BCM63XX SoCs include an on-chip EHCI controller which can be
+driven by the generic ehci-platform driver by using specific power
+on/off/suspend callbacks to manage clocks and hardware specific
+configuration.
+
+Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/Makefile                         |    2 +-
+ arch/mips/bcm63xx/dev-usb-ehci.c                   |   92 ++++++++++++++++++++
+ .../asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h        |    6 ++
+ 3 files changed, 99 insertions(+), 1 deletion(-)
+ create mode 100644 arch/mips/bcm63xx/dev-usb-ehci.c
+ create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
+
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -1,7 +1,7 @@
+ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \
+ 		   setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
+ 		   dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \
+-		   dev-usb-ohci.o dev-usb-usbd.o usb-common.o
++		   dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o usb-common.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- /dev/null
++++ b/arch/mips/bcm63xx/dev-usb-ehci.c
+@@ -0,0 +1,92 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
++ * Copyright (C) 2013 Florian Fainelli <florian@openwrt.org>
++ */
++
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++#include <linux/clk.h>
++#include <linux/delay.h>
++#include <linux/usb/ehci_pdriver.h>
++#include <linux/dma-mapping.h>
++
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_regs.h>
++#include <bcm63xx_io.h>
++#include <bcm63xx_usb_priv.h>
++#include <bcm63xx_dev_usb_ehci.h>
++
++static struct resource ehci_resources[] = {
++	{
++		.start		= -1, /* filled at runtime */
++		.end		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_MEM,
++	},
++	{
++		.start		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++static u64 ehci_dmamask = DMA_BIT_MASK(32);
++
++static struct clk *usb_host_clock;
++
++static int bcm63xx_ehci_power_on(struct platform_device *pdev)
++{
++	usb_host_clock = clk_get(&pdev->dev, "usbh");
++	if (IS_ERR_OR_NULL(usb_host_clock))
++		return -ENODEV;
++
++	clk_prepare_enable(usb_host_clock);
++
++	bcm63xx_usb_priv_ehci_cfg_set();
++
++	return 0;
++}
++
++static void bcm63xx_ehci_power_off(struct platform_device *pdev)
++{
++	if (!IS_ERR_OR_NULL(usb_host_clock)) {
++		clk_disable_unprepare(usb_host_clock);
++		clk_put(usb_host_clock);
++	}
++}
++
++static struct usb_ehci_pdata bcm63xx_ehci_pdata = {
++	.big_endian_desc	= 1,
++	.big_endian_mmio	= 1,
++	.power_on		= bcm63xx_ehci_power_on,
++	.power_off		= bcm63xx_ehci_power_off,
++	.power_suspend		= bcm63xx_ehci_power_off,
++};
++
++static struct platform_device bcm63xx_ehci_device = {
++	.name		= "ehci-platform",
++	.id		= -1,
++	.num_resources	= ARRAY_SIZE(ehci_resources),
++	.resource	= ehci_resources,
++	.dev		= {
++		.platform_data		= &bcm63xx_ehci_pdata,
++		.dma_mask		= &ehci_dmamask,
++		.coherent_dma_mask	= DMA_BIT_MASK(32),
++	},
++};
++
++int __init bcm63xx_ehci_register(void)
++{
++	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6368())
++		return 0;
++
++	ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0);
++	ehci_resources[0].end = ehci_resources[0].start;
++	ehci_resources[0].end += RSET_EHCI_SIZE - 1;
++	ehci_resources[1].start = bcm63xx_get_irq_number(IRQ_EHCI0);
++
++	return platform_device_register(&bcm63xx_ehci_device);
++}
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
+@@ -0,0 +1,6 @@
++#ifndef BCM63XX_DEV_USB_EHCI_H_
++#define BCM63XX_DEV_USB_EHCI_H_
++
++int bcm63xx_ehci_register(void);
++
++#endif /* BCM63XX_DEV_USB_EHCI_H_ */

target/linux/brcm63xx/patches-3.8/117-MIPS-BCM63XX-register-EHCI-controller-if-board-enabl.patch

@@ -0,0 +1,36 @@
+From 709ef2034f5ba06da35f89856ad7baf2b7a41287 Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:28 +0100
+Subject: [PATCH 10/11] MIPS: BCM63XX: register EHCI controller if board
+ enables it
+
+BCM63XX-based board can control the registration of the EHCI controller
+by setting their has_ehci0 flag to 1. Handle this in the generic
+code dealing with board registration and call the actual helper to register
+the EHCI controller.
+
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c |    4 ++++
+ 1 file changed, 4 insertions(+)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -25,6 +25,7 @@
+ #include <bcm63xx_dev_flash.h>
+ #include <bcm63xx_dev_pcmcia.h>
+ #include <bcm63xx_dev_spi.h>
++#include <bcm63xx_dev_usb_ehci.h>
+ #include <bcm63xx_dev_usb_ohci.h>
+ #include <bcm63xx_dev_usb_usbd.h>
+ #include <board_bcm963xx.h>
+@@ -852,6 +853,9 @@ int __init board_register_devices(void)
+ 	if (board.has_usbd)
+ 		bcm63xx_usbd_register(&board.usbd);
+ 
++	if (board.has_ehci0)
++		bcm63xx_ehci_register();
++
+ 	if (board.has_ohci0)
+ 		bcm63xx_ohci_register();
+ 

target/linux/brcm63xx/patches-3.8/118-MIPS-BCM63XX-EHCI-controller-does-not-support-overcu.patch

@@ -0,0 +1,24 @@
+From 111bbd770441ab34f9da5bb1d85767a9b75227b4 Mon Sep 17 00:00:00 2001
+From: Florian Fainelli <florian@openwrt.org>
+Date: Mon, 28 Jan 2013 20:06:30 +0100
+Subject: [PATCH 12/12] MIPS: BCM63XX: EHCI controller does not support
+ overcurrent
+
+This patch sets the ignore_oc flag for the BCM63XX EHCI controller as it
+does not support proper overcurrent reporting.
+
+Signed-off-by: Florian Fainelli <florian@openwrt.org>
+---
+ arch/mips/bcm63xx/dev-usb-ehci.c |    1 +
+ 1 file changed, 1 insertion(+)
+
+--- a/arch/mips/bcm63xx/dev-usb-ehci.c
++++ b/arch/mips/bcm63xx/dev-usb-ehci.c
+@@ -61,6 +61,7 @@ static void bcm63xx_ehci_power_off(struc
+ static struct usb_ehci_pdata bcm63xx_ehci_pdata = {
+ 	.big_endian_desc	= 1,
+ 	.big_endian_mmio	= 1,
++	.ignore_oc		= 1,
+ 	.power_on		= bcm63xx_ehci_power_on,
+ 	.power_off		= bcm63xx_ehci_power_off,
+ 	.power_suspend		= bcm63xx_ehci_power_off,

target/linux/brcm63xx/patches-3.8/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch

@@ -0,0 +1,38 @@
+From 3f650fc30aa0badf9d02842ce396cea3eef2eeaa Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 1 Jul 2011 23:16:47 +0200
+Subject: [PATCH 49/79] SPI: Allow specifying the parsers for SPI flash
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ include/linux/spi/flash.h |    5 ++++-
+ 1 file changed, 4 insertions(+), 1 deletion(-)
+
+--- a/include/linux/spi/flash.h
++++ b/include/linux/spi/flash.h
+@@ -2,7 +2,7 @@
+ #define LINUX_SPI_FLASH_H
+ 
+ struct mtd_partition;
+-
++struct mtd_part_parser_data;
+ /**
+  * struct flash_platform_data: board-specific flash data
+  * @name: optional flash device name (eg, as used with mtdparts=)
+@@ -10,6 +10,8 @@ struct mtd_partition;
+  * @nr_parts: number of mtd_partitions for static partitoning
+  * @type: optional flash device type (e.g. m25p80 vs m25p64), for use
+  *	with chips that can't be queried for JEDEC or other IDs
++ * @part_probe_types: optional list of MTD parser names to use for
++ *	partitioning
+  *
+  * Board init code (in arch/.../mach-xxx/board-yyy.c files) can
+  * provide information about SPI flash parts (such as DataFlash) to
+@@ -25,6 +27,7 @@ struct flash_platform_data {
+ 
+ 	char		*type;
+ 
++	const char	**part_probe_types;
+ 	/* we'll likely add more ... use JEDEC IDs, etc */
+ };
+ 

target/linux/brcm63xx/patches-3.8/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch

@@ -0,0 +1,23 @@
+From c7c3c338cb25d7f55ddb3f6bfbf3572758ca3896 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Thu, 10 Nov 2011 16:53:08 +0100
+Subject: [PATCH 50/79] MTD: DEVICES: m25p80: use parsers if provided in flash
+ platform data
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/mtd/devices/m25p80.c |    3 ++-
+ 1 file changed, 2 insertions(+), 1 deletion(-)
+
+--- a/drivers/mtd/devices/m25p80.c
++++ b/drivers/mtd/devices/m25p80.c
+@@ -987,7 +987,8 @@ static int m25p_probe(struct spi_device
+ 	/* partitions should match sector boundaries; and it may be good to
+ 	 * use readonly partitions for writeprotected sectors (BP2..BP0).
+ 	 */
+-	return mtd_device_parse_register(&flash->mtd, NULL, &ppdata,
++	return mtd_device_parse_register(&flash->mtd,
++			data ? data->part_probe_types : NULL, &ppdata,
+ 			data ? data->parts : NULL,
+ 			data ? data->nr_parts : 0);
+ }

target/linux/brcm63xx/patches-3.8/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch

@@ -0,0 +1,92 @@
+From 5fb4e8d7287ac8fcb33aae8b1e9e22c5a3c392bd Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Thu, 10 Nov 2011 17:33:40 +0100
+Subject: [PATCH 51/79] MTD: DEVICES: m25p80: add support for limiting reads
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/mtd/devices/m25p80.c |   29 +++++++++++++++++++++++++++--
+ include/linux/spi/flash.h    |    4 ++++
+ 2 files changed, 31 insertions(+), 2 deletions(-)
+
+--- a/drivers/mtd/devices/m25p80.c
++++ b/drivers/mtd/devices/m25p80.c
+@@ -93,6 +93,7 @@ struct m25p {
+ 	u8			erase_opcode;
+ 	u8			*command;
+ 	bool			fast_read;
++	int			max_transfer_len;
+ };
+ 
+ static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd)
+@@ -337,10 +338,9 @@ static int m25p80_erase(struct mtd_info
+  * Read an address range from the flash chip.  The address range
+  * may be any size provided it is within the physical boundaries.
+  */
+-static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
++static int __m25p80_read(struct m25p *flash, loff_t from, size_t len,
+ 	size_t *retlen, u_char *buf)
+ {
+-	struct m25p *flash = mtd_to_m25p(mtd);
+ 	struct spi_transfer t[2];
+ 	struct spi_message m;
+ 	uint8_t opcode;
+@@ -392,6 +392,28 @@ static int m25p80_read(struct mtd_info *
+ 	return 0;
+ }
+ 
++static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
++	size_t *retlen, u_char *buf)
++{
++	struct m25p *flash = mtd_to_m25p(mtd);
++	size_t off;
++	size_t read_len = flash->max_transfer_len;
++	size_t part_len;
++	int ret = 0;
++
++	if (!read_len)
++		return __m25p80_read(flash, from, len, retlen, buf);
++
++	*retlen = 0;
++
++	for (off = 0; off < len && !ret; off += read_len) {
++		ret = __m25p80_read(flash, from + off, min(len - off, read_len),
++				    &part_len, buf + off);
++			*retlen += part_len;
++	}
++
++	return ret;
++}
+ /*
+  * Write an address range to the flash chip.  Data must be written in
+  * FLASH_PAGESIZE chunks.  The address range may be any size provided
+@@ -888,6 +910,9 @@ static int m25p_probe(struct spi_device
+ 		return -ENOMEM;
+ 	}
+ 
++	if (data)
++		flash->max_transfer_len = data->max_transfer_len;
++
+ 	flash->spi = spi;
+ 	mutex_init(&flash->lock);
+ 	dev_set_drvdata(&spi->dev, flash);
+--- a/include/linux/spi/flash.h
++++ b/include/linux/spi/flash.h
+@@ -13,6 +13,8 @@ struct mtd_part_parser_data;
+  * @part_probe_types: optional list of MTD parser names to use for
+  *	partitioning
+  *
++ * @max_transfer_len: option maximum read/write length limitation for
++ *	SPI controllers not able to transfer any length commands.
+  * Board init code (in arch/.../mach-xxx/board-yyy.c files) can
+  * provide information about SPI flash parts (such as DataFlash) to
+  * help set up the device and its appropriate default partitioning.
+@@ -28,6 +30,8 @@ struct flash_platform_data {
+ 	char		*type;
+ 
+ 	const char	**part_probe_types;
++
++	unsigned int	max_transfer_len;
+ 	/* we'll likely add more ... use JEDEC IDs, etc */
+ };
+ 

target/linux/brcm63xx/patches-3.8/300-reset_buttons.patch

@@ -0,0 +1,116 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -12,6 +12,8 @@
+ #include <linux/string.h>
+ #include <linux/platform_device.h>
+ #include <linux/ssb/ssb.h>
++#include <linux/gpio_keys.h>
++#include <linux/input.h>
+ #include <asm/addrspace.h>
+ #include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+@@ -32,6 +34,9 @@
+ 
+ #define PFX	"board_bcm963xx: "
+ 
++#define BCM963XX_KEYS_POLL_INTERVAL	20
++#define BCM963XX_KEYS_DEBOUNCE_INTERVAL	(BCM963XX_KEYS_POLL_INTERVAL * 3)
++
+ static struct board_info board;
+ 
+ /*
+@@ -343,6 +348,16 @@ static struct board_info __initdata boar
+ 			.active_low	= 1,
+ 		},
+ 	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 33,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
+ };
+ 
+ static struct board_info __initdata board_96348gw = {
+@@ -401,6 +416,16 @@ static struct board_info __initdata boar
+ 			.active_low	= 1,
+ 		},
+ 	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 36,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
+ };
+ 
+ static struct board_info __initdata board_FAST2404 = {
+@@ -828,11 +853,23 @@ static struct platform_device bcm63xx_gp
+ 	.dev.platform_data	= &bcm63xx_led_data,
+ };
+ 
++static struct gpio_keys_platform_data bcm63xx_gpio_keys_data = {
++	.poll_interval  = BCM963XX_KEYS_POLL_INTERVAL,
++};
++
++static struct platform_device bcm63xx_gpio_keys_device = {
++	.name		= "gpio-keys-polled",
++	.id		= 0,
++	.dev.platform_data = &bcm63xx_gpio_keys_data,
++};
++
+ /*
+  * third stage init callback, register all board devices.
+  */
+ int __init board_register_devices(void)
+ {
++	int button_count = 0;
++
+ 	if (board.has_uart0)
+ 		bcm63xx_uart_register(0);
+ 
+@@ -884,5 +921,16 @@ int __init board_register_devices(void)
+ 
+ 	platform_device_register(&bcm63xx_gpio_leds);
+ 
++	/* count number of BUTTONs defined by this device */
++	while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc)
++		button_count++;
++
++	if (button_count) {
++		bcm63xx_gpio_keys_data.nbuttons = button_count;
++		bcm63xx_gpio_keys_data.buttons = board.buttons;
++
++		platform_device_register(&bcm63xx_gpio_keys_device);
++	}
++
+ 	return 0;
+ }
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -3,6 +3,7 @@
+ 
+ #include <linux/types.h>
+ #include <linux/gpio.h>
++#include <linux/gpio_keys.h>
+ #include <linux/leds.h>
+ #include <bcm63xx_dev_enet.h>
+ #include <bcm63xx_dev_usb_usbd.h>
+@@ -45,6 +46,9 @@ struct board_info {
+ 
+ 	/* GPIO LEDs */
+ 	struct gpio_led leds[5];
++
++	/* Buttons */
++	struct gpio_keys_button buttons[4];
+ };
+ 
+ #endif /* ! BOARD_BCM963XX_H_ */

target/linux/brcm63xx/patches-3.8/301-led_count.patch

@@ -0,0 +1,41 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -869,6 +869,7 @@ static struct platform_device bcm63xx_gp
+ int __init board_register_devices(void)
+ {
+ 	int button_count = 0;
++	int led_count = 0;
+ 
+ 	if (board.has_uart0)
+ 		bcm63xx_uart_register(0);
+@@ -916,10 +917,16 @@ int __init board_register_devices(void)
+ 
+ 	bcm63xx_flash_register();
+ 
+-	bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds);
+-	bcm63xx_led_data.leds = board.leds;
++	/* count number of LEDs defined by this device */
++	while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name)
++		led_count++;
++
++	if (led_count) {
++		bcm63xx_led_data.num_leds = led_count;
++		bcm63xx_led_data.leds = board.leds;
+ 
+-	platform_device_register(&bcm63xx_gpio_leds);
++		platform_device_register(&bcm63xx_gpio_leds);
++	}
+ 
+ 	/* count number of BUTTONs defined by this device */
+ 	while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc)
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -45,7 +45,7 @@ struct board_info {
+ 	struct bcm63xx_dsp_platform_data dsp;
+ 
+ 	/* GPIO LEDs */
+-	struct gpio_led leds[5];
++	struct gpio_led leds[14];
+ 
+ 	/* Buttons */
+ 	struct gpio_keys_button buttons[4];

target/linux/brcm63xx/patches-3.8/302-extended-platform-devices.patch

@@ -0,0 +1,25 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -915,6 +915,9 @@ int __init board_register_devices(void)
+ 
+ 	bcm63xx_spi_register();
+ 
++	if (board.num_devs)
++		platform_add_devices(board.devs, board.num_devs);
++
+ 	bcm63xx_flash_register();
+ 
+ 	/* count number of LEDs defined by this device */
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -49,6 +49,10 @@ struct board_info {
+ 
+ 	/* Buttons */
+ 	struct gpio_keys_button buttons[4];
++
++	/* Additional platform devices */
++	struct platform_device **devs;
++	unsigned int	num_devs;
+ };
+ 
+ #endif /* ! BOARD_BCM963XX_H_ */

target/linux/brcm63xx/patches-3.8/303-spi-board-info.patch

@@ -0,0 +1,33 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -14,6 +14,7 @@
+ #include <linux/ssb/ssb.h>
+ #include <linux/gpio_keys.h>
+ #include <linux/input.h>
++#include <linux/spi/spi.h>
+ #include <asm/addrspace.h>
+ #include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+@@ -918,6 +919,9 @@ int __init board_register_devices(void)
+ 	if (board.num_devs)
+ 		platform_add_devices(board.devs, board.num_devs);
+ 
++	if (board.num_spis)
++		spi_register_board_info(board.spis, board.num_spis);
++
+ 	bcm63xx_flash_register();
+ 
+ 	/* count number of LEDs defined by this device */
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -53,6 +53,10 @@ struct board_info {
+ 	/* Additional platform devices */
+ 	struct platform_device **devs;
+ 	unsigned int	num_devs;
++
++	/* Additional platform devices */
++	struct spi_board_info *spis;
++	unsigned int	num_spis;
+ };
+ 
+ #endif /* ! BOARD_BCM963XX_H_ */

target/linux/brcm63xx/patches-3.8/304-boardid_fixup.patch

@@ -0,0 +1,62 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -33,11 +33,16 @@
+ #include <bcm63xx_dev_usb_usbd.h>
+ #include <board_bcm963xx.h>
+ 
++#include <uapi/linux/bcm963xx_tag.h>
++
+ #define PFX	"board_bcm963xx: "
+ 
+ #define BCM963XX_KEYS_POLL_INTERVAL	20
+ #define BCM963XX_KEYS_DEBOUNCE_INTERVAL	(BCM963XX_KEYS_POLL_INTERVAL * 3)
+ 
++#define CFE_OFFSET_64K			0x10000
++#define CFE_OFFSET_128K			0x20000
++
+ static struct board_info board;
+ 
+ /*
+@@ -742,6 +747,30 @@ const char *board_get_name(void)
+ 	return board.name;
+ }
+ 
++static void __init boardid_fixup(u8 *boot_addr)
++{
++	struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K);
++	char *board_name = (char *)bcm63xx_nvram_get_name();
++
++	/* check if bcm_tag is at 64k offset */
++	if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) {
++		/* else try 128k */
++		tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_128K);
++		if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) {
++			/* No tag found */
++			printk(KERN_DEBUG "No bcm_tag found!\n");
++			return;
++		}
++	}
++	/* check if we should override the boardid */
++	if (tag->information1[0] != '+')
++		return;
++
++	strncpy(board_name, &tag->information1[1], BOARDID_LEN);
++
++	printk(KERN_INFO "Overriding boardid with '%s'\n", board_name);
++}
++
+ /*
+  * early init callback, read nvram data from flash and checksum it
+  */
+@@ -778,6 +807,11 @@ void __init board_prom_init(void)
+ 		return;
+ 	}
+ 
++	if (strcmp(cfe_version, "unknown") != 0) {
++		/* cfe present */
++		boardid_fixup(boot_addr);
++	}
++
+ 	board_name = bcm63xx_nvram_get_name();
+ 	/* find board by name */
+ 	for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {

target/linux/brcm63xx/patches-3.8/306-Revert-MIPS-BCM63XX-Call-board_register_device-from-.patch

@@ -0,0 +1,23 @@
+From a7d2622b6614fdca504c074a0cd307d5a1165c30 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 8 May 2012 09:39:01 +0200
+Subject: [PATCH 04/59] Revert "MIPS: BCM63XX: Call board_register_device from device_initcall()"
+
+This commit causes a race between PCI scan and SSB fallback SPROM handler
+registration, causing the wifi to not work on slower systems. The only
+subsystem touched from board_register_device is platform device
+registration, which should be safe as an arch init call.
+
+This reverts commit d64ed7ada2f689d2c62af1892ca55e47d3653e36.
+---
+ arch/mips/bcm63xx/setup.c |    2 +-
+ 1 files changed, 1 insertions(+), 1 deletions(-)
+
+--- a/arch/mips/bcm63xx/setup.c
++++ b/arch/mips/bcm63xx/setup.c
+@@ -157,4 +157,4 @@ int __init bcm63xx_register_devices(void
+ 	return board_register_devices();
+ }
+ 
+-device_initcall(bcm63xx_register_devices);
++arch_initcall(bcm63xx_register_devices);

target/linux/brcm63xx/patches-3.8/307-MIPS-BCM63XX-allow-second-UART-on-BCM6328.patch

@@ -0,0 +1,22 @@
+From c110865541e2d3782c412af9d48c016de5a64d9c Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 14 Jun 2011 21:14:39 +0200
+Subject: [PATCH 42/79] MIPS: BCM63XX: allow second UART on BCM6328
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/dev-uart.c |    3 ++-
+ 1 file changed, 2 insertions(+), 1 deletion(-)
+
+--- a/arch/mips/bcm63xx/dev-uart.c
++++ b/arch/mips/bcm63xx/dev-uart.c
+@@ -54,7 +54,8 @@ int __init bcm63xx_uart_register(unsigne
+ 	if (id >= ARRAY_SIZE(bcm63xx_uart_devices))
+ 		return -ENODEV;
+ 
+-	if (id == 1 && (!BCMCPU_IS_6358() && !BCMCPU_IS_6368()))
++	if (id == 1 && !BCMCPU_IS_6328() && !BCMCPU_IS_6358() &&
++	    !BCMCPU_IS_6368())
+ 		return -ENODEV;
+ 
+ 	if (id == 0) {

target/linux/brcm63xx/patches-3.8/308-MIPS-BCM63XX-expose-the-HS-SPI-clock.patch

@@ -0,0 +1,48 @@
+From 5aeb6273a610f8aab090b3499827177eb41311ba Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sat, 12 Nov 2011 12:19:09 +0100
+Subject: [PATCH 53/79] MIPS: BCM63XX: expose the HS SPI clock
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/clk.c |   22 ++++++++++++++++++++++
+ 1 file changed, 22 insertions(+)
+
+--- a/arch/mips/bcm63xx/clk.c
++++ b/arch/mips/bcm63xx/clk.c
+@@ -217,6 +217,26 @@ static struct clk clk_spi = {
+ };
+ 
+ /*
++ * SPI clock
++ */
++static void hsspi_set(struct clk *clk, int enable)
++{
++	u32 mask;
++
++	if (BCMCPU_IS_6328())
++		mask = CKCTL_6328_HSSPI_EN;
++	else
++		return;
++
++	bcm_hwclock_set(mask, enable);
++}
++
++static struct clk clk_hsspi = {
++	.set	= hsspi_set,
++};
++
++
++/*
+  * XTM clock
+  */
+ static void xtm_set(struct clk *clk, int enable)
+@@ -319,6 +339,8 @@ struct clk *clk_get(struct device *dev,
+ 		return &clk_usbd;
+ 	if (!strcmp(id, "spi"))
+ 		return &clk_spi;
++	if (!strcmp(id, "hsspi"))
++		return &clk_hsspi;
+ 	if (!strcmp(id, "xtm"))
+ 		return &clk_xtm;
+ 	if (!strcmp(id, "periph"))

target/linux/brcm63xx/patches-3.8/309-MIPS-BCM63XX-add-HSSPI-register-definitions.patch

@@ -0,0 +1,211 @@
+From 70f970222bc1096689ae1bffeb9ed09a7c4bed07 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sat, 12 Nov 2011 12:19:55 +0100
+Subject: [PATCH 28/60] MIPS: BCM63XX: add HSSPI register definitions
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h  |   18 ++++++++
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h |   47 +++++++++++++++++++++
+ 2 files changed, 65 insertions(+), 0 deletions(-)
+
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
+@@ -116,6 +116,7 @@ enum bcm63xx_regs_set {
+ 	RSET_UART1,
+ 	RSET_GPIO,
+ 	RSET_SPI,
++	RSET_HSSPI,
+ 	RSET_UDC0,
+ 	RSET_OHCI0,
+ 	RSET_OHCI_PRIV,
+@@ -161,6 +162,7 @@ enum bcm63xx_regs_set {
+ #define RSET_ENETDMA_SIZE		2048
+ #define RSET_ENETSW_SIZE		65536
+ #define RSET_UART_SIZE			24
++#define RSET_HSSPI_SIZE			1536
+ #define RSET_UDC_SIZE			256
+ #define RSET_OHCI_SIZE			256
+ #define RSET_EHCI_SIZE			256
+@@ -186,6 +188,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6328_UART1_BASE		(0xb0000120)
+ #define BCM_6328_GPIO_BASE		(0xb0000080)
+ #define BCM_6328_SPI_BASE		(0xdeadbeef)
++#define BCM_6328_HSSPI_BASE		(0xb0001000)
+ #define BCM_6328_UDC0_BASE		(0xdeadbeef)
+ #define BCM_6328_USBDMA_BASE		(0xb000c000)
+ #define BCM_6328_OHCI0_BASE		(0xb0002600)
+@@ -232,6 +235,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6338_UART1_BASE		(0xdeadbeef)
+ #define BCM_6338_GPIO_BASE		(0xfffe0400)
+ #define BCM_6338_SPI_BASE		(0xfffe0c00)
++#define BCM_6338_HSSPI_BASE		(0xdeadbeef)
+ #define BCM_6338_UDC0_BASE		(0xdeadbeef)
+ #define BCM_6338_USBDMA_BASE		(0xfffe2400)
+ #define BCM_6338_OHCI0_BASE		(0xdeadbeef)
+@@ -279,6 +283,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6345_UART1_BASE		(0xdeadbeef)
+ #define BCM_6345_GPIO_BASE		(0xfffe0400)
+ #define BCM_6345_SPI_BASE		(0xdeadbeef)
++#define BCM_6345_HSSPI_BASE		(0xdeadbeef)
+ #define BCM_6345_UDC0_BASE		(0xdeadbeef)
+ #define BCM_6345_USBDMA_BASE		(0xfffe2800)
+ #define BCM_6345_ENET0_BASE		(0xfffe1800)
+@@ -325,6 +330,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6348_UART1_BASE		(0xdeadbeef)
+ #define BCM_6348_GPIO_BASE		(0xfffe0400)
+ #define BCM_6348_SPI_BASE		(0xfffe0c00)
++#define BCM_6348_HSSPI_BASE		(0xdeadbeef)
+ #define BCM_6348_UDC0_BASE		(0xfffe1000)
+ #define BCM_6348_USBDMA_BASE		(0xdeadbeef)
+ #define BCM_6348_OHCI0_BASE		(0xfffe1b00)
+@@ -370,6 +376,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6358_UART1_BASE		(0xfffe0120)
+ #define BCM_6358_GPIO_BASE		(0xfffe0080)
+ #define BCM_6358_SPI_BASE		(0xfffe0800)
++#define BCM_6358_HSSPI_BASE		(0xdeadbeef)
+ #define BCM_6358_UDC0_BASE		(0xfffe0800)
+ #define BCM_6358_USBDMA_BASE		(0xdeadbeef)
+ #define BCM_6358_OHCI0_BASE		(0xfffe1400)
+@@ -416,6 +423,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6368_UART1_BASE		(0xb0000120)
+ #define BCM_6368_GPIO_BASE		(0xb0000080)
+ #define BCM_6368_SPI_BASE		(0xb0000800)
++#define BCM_6368_HSSPI_BASE		(0xdeadbeef)
+ #define BCM_6368_UDC0_BASE		(0xdeadbeef)
+ #define BCM_6368_USBDMA_BASE		(0xb0004800)
+ #define BCM_6368_OHCI0_BASE		(0xb0001600)
+@@ -467,6 +475,7 @@ extern const unsigned long *bcm63xx_regs
+ 	__GEN_RSET_BASE(__cpu, UART1)					\
+ 	__GEN_RSET_BASE(__cpu, GPIO)					\
+ 	__GEN_RSET_BASE(__cpu, SPI)					\
++	__GEN_RSET_BASE(__cpu, HSSPI)					\
+ 	__GEN_RSET_BASE(__cpu, UDC0)					\
+ 	__GEN_RSET_BASE(__cpu, OHCI0)					\
+ 	__GEN_RSET_BASE(__cpu, OHCI_PRIV)				\
+@@ -510,6 +519,7 @@ extern const unsigned long *bcm63xx_regs
+ 	[RSET_UART1]		= BCM_## __cpu ##_UART1_BASE,		\
+ 	[RSET_GPIO]		= BCM_## __cpu ##_GPIO_BASE,		\
+ 	[RSET_SPI]		= BCM_## __cpu ##_SPI_BASE,		\
++	[RSET_HSSPI]		= BCM_## __cpu ##_HSSPI_BASE,		\
+ 	[RSET_UDC0]		= BCM_## __cpu ##_UDC0_BASE,		\
+ 	[RSET_OHCI0]		= BCM_## __cpu ##_OHCI0_BASE,		\
+ 	[RSET_OHCI_PRIV]	= BCM_## __cpu ##_OHCI_PRIV_BASE,	\
+@@ -584,6 +594,7 @@ enum bcm63xx_irq {
+ 	IRQ_ENET0,
+ 	IRQ_ENET1,
+ 	IRQ_ENET_PHY,
++	IRQ_HSSPI,
+ 	IRQ_OHCI0,
+ 	IRQ_EHCI0,
+ 	IRQ_USBD,
+@@ -626,6 +637,7 @@ enum bcm63xx_irq {
+ #define BCM_6328_ENET0_IRQ		0
+ #define BCM_6328_ENET1_IRQ		0
+ #define BCM_6328_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 12)
++#define BCM_6328_HSSPI_IRQ		(IRQ_INTERNAL_BASE + 29)
+ #define BCM_6328_OHCI0_IRQ		(BCM_6328_HIGH_IRQ_BASE + 9)
+ #define BCM_6328_EHCI0_IRQ		(BCM_6328_HIGH_IRQ_BASE + 10)
+ #define BCM_6328_USBD_IRQ		(IRQ_INTERNAL_BASE + 4)
+@@ -671,6 +683,7 @@ enum bcm63xx_irq {
+ #define BCM_6338_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+ #define BCM_6338_ENET1_IRQ		0
+ #define BCM_6338_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 9)
++#define BCM_6338_HSSPI_IRQ		0
+ #define BCM_6338_OHCI0_IRQ		0
+ #define BCM_6338_EHCI0_IRQ		0
+ #define BCM_6338_USBD_IRQ		0
+@@ -709,6 +722,7 @@ enum bcm63xx_irq {
+ #define BCM_6345_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+ #define BCM_6345_ENET1_IRQ		0
+ #define BCM_6345_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 12)
++#define BCM_6345_HSSPI_IRQ		0
+ #define BCM_6345_OHCI0_IRQ		0
+ #define BCM_6345_EHCI0_IRQ		0
+ #define BCM_6345_USBD_IRQ		0
+@@ -747,6 +761,7 @@ enum bcm63xx_irq {
+ #define BCM_6348_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+ #define BCM_6348_ENET1_IRQ		(IRQ_INTERNAL_BASE + 7)
+ #define BCM_6348_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 9)
++#define BCM_6348_HSSPI_IRQ		0
+ #define BCM_6348_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 12)
+ #define BCM_6348_EHCI0_IRQ		0
+ #define BCM_6348_USBD_IRQ		0
+@@ -785,6 +800,7 @@ enum bcm63xx_irq {
+ #define BCM_6358_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+ #define BCM_6358_ENET1_IRQ		(IRQ_INTERNAL_BASE + 6)
+ #define BCM_6358_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 9)
++#define BCM_6358_HSSPI_IRQ		0
+ #define BCM_6358_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 5)
+ #define BCM_6358_EHCI0_IRQ		(IRQ_INTERNAL_BASE + 10)
+ #define BCM_6358_USBD_IRQ		0
+@@ -832,6 +848,7 @@ enum bcm63xx_irq {
+ #define BCM_6368_ENET0_IRQ		0
+ #define BCM_6368_ENET1_IRQ		0
+ #define BCM_6368_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 15)
++#define BCM_6368_HSSPI_IRQ		0
+ #define BCM_6368_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 5)
+ #define BCM_6368_EHCI0_IRQ		(IRQ_INTERNAL_BASE + 7)
+ #define BCM_6368_USBD_IRQ		(IRQ_INTERNAL_BASE + 8)
+@@ -879,6 +896,7 @@ extern const int *bcm63xx_irqs;
+ 	[IRQ_ENET0]		= BCM_## __cpu ##_ENET0_IRQ,		\
+ 	[IRQ_ENET1]		= BCM_## __cpu ##_ENET1_IRQ,		\
+ 	[IRQ_ENET_PHY]		= BCM_## __cpu ##_ENET_PHY_IRQ,		\
++	[IRQ_HSSPI]		= BCM_## __cpu ##_HSSPI_IRQ,		\
+ 	[IRQ_OHCI0]		= BCM_## __cpu ##_OHCI0_IRQ,		\
+ 	[IRQ_EHCI0]		= BCM_## __cpu ##_EHCI0_IRQ,		\
+ 	[IRQ_USBD]		= BCM_## __cpu ##_USBD_IRQ,		\
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -1409,4 +1409,51 @@
+ 
+ #define PCIE_DEVICE_OFFSET		0x8000
+ 
++/*************************************************************************
++ * _REG relative to RSET_HSSPI
++ *************************************************************************/
++
++#define HSSPI_GLOBAL_CTRL_REG			0x0
++#define GLOBAL_CTRL_CLK_POLARITY		(1 << 17)
++#define GLOBAL_CTRL_CLK_GATE_SSOFF		(1 << 16)
++
++#define HSSPI_GLOBAL_EXT_TRIGGER_REG		0x4
++
++#define HSSPI_INT_STATUS_REG			0x8
++#define HSSPI_INT_STATUS_MASKED_REG		0xc
++#define HSSPI_INT_MASK_REG			0x10
++
++#define HSSPI_PING0_CMD_DONE			(1 << 0)
++
++#define HSSPI_INT_CLEAR_ALL			0xff001f1f
++
++#define HSSPI_PINGPONG_COMMAND_REG(x)		(0x80 + (x) * 0x40)
++#define PINGPONG_CMD_COMMAND_MASK		0xf
++#define PINGPONG_COMMAND_NOOP			0
++#define PINGPONG_COMMAND_START_NOW		1
++#define PINGPONG_COMMAND_START_TRIGGER		2
++#define PINGPONG_COMMAND_HALT			3
++#define PINGPONG_COMMAND_FLUSH			4
++#define PINGPONG_CMD_PROFILE_SHIFT		8
++#define PINGPONG_CMD_SS_SHIFT			12
++
++#define HSSPI_PINGPONG_STATUS_REG(x)		(0x84 + (x) * 0x40)
++
++#define HSSPI_PROFILE_CLK_CTRL_REG(x)		(0x100 + (x) * 0x20)
++#define CLK_CTRL_ACCUM_RST_ON_LOOP		(1 << 15)
++
++#define HSSPI_PROFILE_SIGNAL_CTRL_REG(x)	(0x104 + (x) * 0x20)
++#define SIGNAL_CTRL_LATCH_RISING		(1 << 12)
++#define SIGNAL_CTRL_LAUNCH_RISING		(1 << 13)
++#define SIGNAL_CTRL_ASYNC_INPUT_PATH		(1 << 16)
++
++#define HSSPI_PROFILE_MODE_CTRL_REG(x)		(0x108 + (x) * 0x20)
++#define MODE_CTRL_MULTIDATA_RD_STRT_SHIFT	8
++#define MODE_CTRL_MULTIDATA_WR_STRT_SHIFT	12
++#define MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT	16
++#define MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT	18
++#define MODE_CTRL_PREPENDBYTE_CNT_SHIFT		24
++
++#define HSSPI_FIFO_REG(x)			(0x200 + (x) * 0x200)
++
+ #endif /* BCM63XX_REGS_H_ */

target/linux/brcm63xx/patches-3.8/310-board_leds_naming.patch

@@ -0,0 +1,267 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -112,28 +112,28 @@ static struct board_info __initdata boar
+ 
+ 	.leds = {
+ 		{
+-			.name		= "adsl",
++			.name		= "96338GW:green:adsl",
+ 			.gpio		= 3,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ses",
++			.name		= "96338GW:green:ses",
+ 			.gpio		= 5,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp-fail",
++			.name		= "96338GW:green:ppp-fail",
+ 			.gpio		= 4,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "power",
++			.name		= "96338GW:green:power",
+ 			.gpio		= 0,
+ 			.active_low	= 1,
+ 			.default_trigger = "default-on",
+ 		},
+ 		{
+-			.name		= "stop",
++			.name		= "96338GW:green:stop",
+ 			.gpio		= 1,
+ 			.active_low	= 1,
+ 		}
+@@ -153,28 +153,28 @@ static struct board_info __initdata boar
+ 
+ 	.leds = {
+ 		{
+-			.name		= "adsl",
++			.name		= "96338W:green:adsl",
+ 			.gpio		= 3,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ses",
++			.name		= "96338W:green:ses",
+ 			.gpio		= 5,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp-fail",
++			.name		= "96338W:green:ppp-fail",
+ 			.gpio		= 4,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "power",
++			.name		= "96338W:green:power",
+ 			.gpio		= 0,
+ 			.active_low	= 1,
+ 			.default_trigger = "default-on",
+ 		},
+ 		{
+-			.name		= "stop",
++			.name		= "96338W:green:stop",
+ 			.gpio		= 1,
+ 			.active_low	= 1,
+ 		},
+@@ -213,29 +213,29 @@ static struct board_info __initdata boar
+ 
+ 	.leds = {
+ 		{
+-			.name		= "adsl-fail",
++			.name		= "96348R:green:adsl-fail",
+ 			.gpio		= 2,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp",
++			.name		= "96348R:green:ppp",
+ 			.gpio		= 3,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp-fail",
++			.name		= "96348R:green:ppp-fail",
+ 			.gpio		= 4,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "power",
++			.name		= "96348R:green:power",
+ 			.gpio		= 0,
+ 			.active_low	= 1,
+ 			.default_trigger = "default-on",
+ 
+ 		},
+ 		{
+-			.name		= "stop",
++			.name		= "96348R:green:stop",
+ 			.gpio		= 1,
+ 			.active_low	= 1,
+ 		},
+@@ -274,28 +274,28 @@ static struct board_info __initdata boar
+ 
+ 	.leds = {
+ 		{
+-			.name		= "adsl-fail",
++			.name		= "96348GW-10:green:adsl-fail",
+ 			.gpio		= 2,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp",
++			.name		= "96348GW-10:green:ppp",
+ 			.gpio		= 3,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp-fail",
++			.name		= "96348GW-10:green:ppp-fail",
+ 			.gpio		= 4,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "power",
++			.name		= "96348GW-10:green:power",
+ 			.gpio		= 0,
+ 			.active_low	= 1,
+ 			.default_trigger = "default-on",
+ 		},
+ 		{
+-			.name		= "stop",
++			.name		= "96348GW-10:green:stop",
+ 			.gpio		= 1,
+ 			.active_low	= 1,
+ 		},
+@@ -328,28 +328,28 @@ static struct board_info __initdata boar
+ 
+ 	.leds = {
+ 		{
+-			.name		= "adsl-fail",
++			.name		= "96348GW-11:green:adsl-fail",
+ 			.gpio		= 2,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp",
++			.name		= "96348GW-11:green:ppp",
+ 			.gpio		= 3,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp-fail",
++			.name		= "96348GW-11:green:ppp-fail",
+ 			.gpio		= 4,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "power",
++			.name		= "96348GW-11:green:power",
+ 			.gpio		= 0,
+ 			.active_low	= 1,
+ 			.default_trigger = "default-on",
+ 		},
+ 		{
+-			.name		= "stop",
++			.name		= "96348GW-11:green:stop",
+ 			.gpio		= 1,
+ 			.active_low	= 1,
+ 		},
+@@ -396,28 +396,28 @@ static struct board_info __initdata boar
+ 
+ 	.leds = {
+ 		{
+-			.name		= "adsl-fail",
++			.name		= "96348GW:green:adsl-fail",
+ 			.gpio		= 2,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp",
++			.name		= "96348GW:green:ppp",
+ 			.gpio		= 3,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp-fail",
++			.name		= "96348GW:green:ppp-fail",
+ 			.gpio		= 4,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "power",
++			.name		= "96348GW:green:power",
+ 			.gpio		= 0,
+ 			.active_low	= 1,
+ 			.default_trigger = "default-on",
+ 		},
+ 		{
+-			.name		= "stop",
++			.name		= "96348GW:green:stop",
+ 			.gpio		= 1,
+ 			.active_low	= 1,
+ 		},
+@@ -549,27 +549,27 @@ static struct board_info __initdata boar
+ 
+ 	.leds = {
+ 		{
+-			.name		= "adsl-fail",
++			.name		= "96358VW:green:adsl-fail",
+ 			.gpio		= 15,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp",
++			.name		= "96358VW:green:ppp",
+ 			.gpio		= 22,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp-fail",
++			.name		= "96358VW:green:ppp-fail",
+ 			.gpio		= 23,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "power",
++			.name		= "96358VW:green:power",
+ 			.gpio		= 4,
+ 			.default_trigger = "default-on",
+ 		},
+ 		{
+-			.name		= "stop",
++			.name		= "96358VW:green:stop",
+ 			.gpio		= 5,
+ 		},
+ 	},
+@@ -601,22 +601,22 @@ static struct board_info __initdata boar
+ 
+ 	.leds = {
+ 		{
+-			.name		= "adsl",
++			.name		= "96358VW2:green:adsl",
+ 			.gpio		= 22,
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "ppp-fail",
++			.name		= "96358VW2:green:ppp-fail",
+ 			.gpio		= 23,
+ 		},
+ 		{
+-			.name		= "power",
++			.name		= "96358VW2:green:power",
+ 			.gpio		= 5,
+ 			.active_low	= 1,
+ 			.default_trigger = "default-on",
+ 		},
+ 		{
+-			.name		= "stop",
++			.name		= "96358VW2:green:stop",
+ 			.gpio		= 4,
+ 			.active_low	= 1,
+ 		},

target/linux/brcm63xx/patches-3.8/311-cfe_version_mod.patch

@@ -0,0 +1,26 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -798,6 +798,8 @@ void __init board_prom_init(void)
+ 	if (!memcmp(cfe, "cfe-v", 5))
+ 		snprintf(cfe_version, sizeof(cfe_version), "%u.%u.%u-%u.%u",
+ 			 cfe[5], cfe[6], cfe[7], cfe[8], cfe[9]);
++	else if (!memcmp(cfe, "cfe-", 4))
++		snprintf(cfe_version, 16, "%s", (char *) &cfe[4]);
+ 	else
+ 		strcpy(cfe_version, "unknown");
+ 	printk(KERN_INFO PFX "CFE version: %s\n", cfe_version);
+--- a/drivers/mtd/bcm63xxpart.c
++++ b/drivers/mtd/bcm63xxpart.c
+@@ -54,10 +54,10 @@ static int bcm63xx_detect_cfe(struct mtd
+ 	if (ret)
+ 		return ret;
+ 
+-	if (strncmp("cfe-v", buf, 5) == 0)
++	if (strncmp("cfe-", buf, 4) == 0)
+ 		return 0;
+ 
+-	/* very old CFE's do not have the cfe-v string, so check for magic */
++	/* very old CFE's do not have the cfe- string, so check for magic */
+ 	ret = mtd_read(master, BCM63XX_CFE_MAGIC_OFFSET, 8, &retlen,
+ 		       (void *)buf);
+ 	buf[retlen] = 0;

target/linux/brcm63xx/patches-3.8/312-MIPS-BCM63XX-add-basic-BCM6362-support.patch

@@ -0,0 +1,556 @@
+From 2665f554de21676a4cf609b1e1bb39d0597a1985 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Mon, 21 Nov 2011 00:48:52 +0100
+Subject: [PATCH 28/72] MIPS: BCM63XX: add basic BCM6362 support
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/Kconfig                         |    4 +
+ arch/mips/bcm63xx/boards/board_bcm963xx.c         |    2 +-
+ arch/mips/bcm63xx/cpu.c                           |   52 +++++++-
+ arch/mips/bcm63xx/irq.c                           |   19 +++
+ arch/mips/bcm63xx/prom.c                          |    2 +
+ arch/mips/bcm63xx/reset.c                         |   28 +++++
+ arch/mips/bcm63xx/setup.c                         |    3 +
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h  |  139 +++++++++++++++++++++
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h |    2 +
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h |   59 +++++++++
+ arch/mips/include/asm/mach-bcm63xx/ioremap.h      |    1 +
+ 11 files changed, 309 insertions(+), 2 deletions(-)
+
+--- a/arch/mips/bcm63xx/Kconfig
++++ b/arch/mips/bcm63xx/Kconfig
+@@ -37,6 +37,10 @@ config BCM63XX_CPU_6358
+ 	select BCM63XX_OHCI
+ 	select BCM63XX_EHCI
+ 
++config BCM63XX_CPU_6362
++	bool "support 6362 CPU"
++	select HW_HAS_PCI
++
+ config BCM63XX_CPU_6368
+ 	bool "support 6368 CPU"
+ 	select HW_HAS_PCI
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -785,7 +785,7 @@ void __init board_prom_init(void)
+ 	/* read base address of boot chip select (0)
+ 	 * 6328 does not have MPI but boots from a fixed address
+ 	 */
+-	if (BCMCPU_IS_6328())
++	if (BCMCPU_IS_6328() || BCMCPU_IS_6362())
+ 		val = 0x18000000;
+ 	else {
+ 		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+--- a/arch/mips/bcm63xx/cpu.c
++++ b/arch/mips/bcm63xx/cpu.c
+@@ -71,6 +71,15 @@ static const int bcm6358_irqs[] = {
+ 
+ };
+ 
++static const unsigned long bcm6362_regs_base[] = {
++	__GEN_CPU_REGS_TABLE(6362)
++};
++
++static const int bcm6362_irqs[] = {
++	__GEN_CPU_IRQ_TABLE(6362)
++
++};
++
+ static const unsigned long bcm6368_regs_base[] = {
+ 	__GEN_CPU_REGS_TABLE(6368)
+ };
+@@ -169,6 +178,42 @@ static unsigned int detect_cpu_clock(voi
+ 		return (16 * 1000000 * n1 * n2) / m1;
+ 	}
+ 
++	case BCM6362_CPU_ID:
++	{
++		unsigned int tmp, mips_pll_fcvo;
++
++		tmp = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
++		mips_pll_fcvo = (tmp & STRAPBUS_6362_FCVO_MASK)
++				>> STRAPBUS_6362_FCVO_SHIFT;
++		switch (mips_pll_fcvo) {
++		case 0x03:
++		case 0x0b:
++		case 0x13:
++		case 0x1b:
++			return 240000000;
++		case 0x04:
++		case 0x0c:
++		case 0x14:
++		case 0x1c:
++			return 160000000;
++		case 0x05:
++		case 0x0e:
++		case 0x16:
++		case 0x1e:
++		case 0x1f:
++			return 400000000;
++		case 0x06:
++			return 440000000;
++		case 0x07:
++		case 0x17:
++			return 384000000;
++		case 0x15:
++		case 0x1d:
++			return 200000000;
++		default:
++			return 320000000;
++		}
++	}
+ 	case BCM6368_CPU_ID:
+ 	{
+ 		unsigned int tmp, p1, p2, ndiv, m1;
+@@ -205,7 +250,7 @@ static unsigned int detect_memory_size(v
+ 	unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0;
+ 	u32 val;
+ 
+-	if (BCMCPU_IS_6328())
++	if (BCMCPU_IS_6328() || BCMCPU_IS_6362())
+ 		return bcm_ddr_readl(DDR_CSEND_REG) << 24;
+ 
+ 	if (BCMCPU_IS_6345()) {
+@@ -280,6 +325,11 @@ void __init bcm63xx_cpu_init(void)
+ 				bcm63xx_regs_base = bcm6328_regs_base;
+ 				bcm63xx_irqs = bcm6328_irqs;
+ 				break;
++			case BCM6362_CPU_ID:
++				expected_cpu_id = BCM6362_CPU_ID;
++				bcm63xx_regs_base = bcm6362_regs_base;
++				bcm63xx_irqs = bcm6362_irqs;
++				break;
+ 			case BCM6368_CPU_ID:
+ 				expected_cpu_id = BCM6368_CPU_ID;
+ 				bcm63xx_regs_base = bcm6368_regs_base;
+--- a/arch/mips/bcm63xx/irq.c
++++ b/arch/mips/bcm63xx/irq.c
+@@ -82,6 +82,14 @@ static void __internal_irq_unmask_64(uns
+ #define ext_irq_cfg_reg1	PERF_EXTIRQ_CFG_REG_6358
+ #define ext_irq_cfg_reg2	0
+ #endif
++#ifdef CONFIG_BCM63XX_CPU_6362
++#define irq_stat_reg		PERF_IRQSTAT_6362_REG
++#define irq_mask_reg		PERF_IRQMASK_6362_REG
++#define irq_bits		64
++#define is_ext_irq_cascaded	1
++#define ext_irq_start		(BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE)
++#define ext_irq_end		(BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE)
++#endif
+ #ifdef CONFIG_BCM63XX_CPU_6368
+ #define irq_stat_reg		PERF_IRQSTAT_6368_REG
+ #define irq_mask_reg		PERF_IRQMASK_6368_REG
+@@ -170,6 +178,16 @@ static void bcm63xx_init_irq(void)
+ 		ext_irq_end = BCM_6358_EXT_IRQ3 - IRQ_INTERNAL_BASE;
+ 		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6358;
+ 		break;
++	case BCM6362_CPU_ID:
++		irq_stat_addr += PERF_IRQSTAT_6362_REG;
++		irq_mask_addr += PERF_IRQMASK_6362_REG;
++		irq_bits = 64;
++		ext_irq_count = 4;
++		is_ext_irq_cascaded = 1;
++		ext_irq_start = BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE;
++		ext_irq_end = BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE;
++		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6362;
++		break;
+ 	case BCM6368_CPU_ID:
+ 		irq_stat_addr += PERF_IRQSTAT_6368_REG;
+ 		irq_mask_addr += PERF_IRQMASK_6368_REG;
+@@ -458,6 +476,7 @@ static int bcm63xx_external_irq_set_type
+ 	case BCM6338_CPU_ID:
+ 	case BCM6345_CPU_ID:
+ 	case BCM6358_CPU_ID:
++	case BCM6362_CPU_ID:
+ 	case BCM6368_CPU_ID:
+ 		if (levelsense)
+ 			reg |= EXTIRQ_CFG_LEVELSENSE(irq);
+--- a/arch/mips/bcm63xx/prom.c
++++ b/arch/mips/bcm63xx/prom.c
+@@ -36,6 +36,8 @@ void __init prom_init(void)
+ 		mask = CKCTL_6348_ALL_SAFE_EN;
+ 	else if (BCMCPU_IS_6358())
+ 		mask = CKCTL_6358_ALL_SAFE_EN;
++	else if (BCMCPU_IS_6362())
++		mask = CKCTL_6362_ALL_SAFE_EN;
+ 	else if (BCMCPU_IS_6368())
+ 		mask = CKCTL_6368_ALL_SAFE_EN;
+ 	else
+--- a/arch/mips/bcm63xx/reset.c
++++ b/arch/mips/bcm63xx/reset.c
+@@ -85,6 +85,20 @@
+ #define BCM6358_RESET_PCIE	0
+ #define BCM6358_RESET_PCIE_EXT	0
+ 
++#define BCM6362_RESET_SPI	SOFTRESET_6362_SPI_MASK
++#define BCM6362_RESET_ENET	0
++#define BCM6362_RESET_USBH	SOFTRESET_6362_USBH_MASK
++#define BCM6362_RESET_USBD	SOFTRESET_6362_USBS_MASK
++#define BCM6362_RESET_DSL	0
++#define BCM6362_RESET_SAR	SOFTRESET_6362_SAR_MASK
++#define BCM6362_RESET_EPHY	SOFTRESET_6362_EPHY_MASK
++#define BCM6362_RESET_ENETSW	SOFTRESET_6362_ENETSW_MASK
++#define BCM6362_RESET_PCM	SOFTRESET_6362_PCM_MASK
++#define BCM6362_RESET_MPI	0
++#define BCM6362_RESET_PCIE      (SOFTRESET_6362_PCIE_MASK | \
++				 SOFTRESET_6362_PCIE_CORE_MASK)
++#define BCM6362_RESET_PCIE_EXT	SOFTRESET_6362_PCIE_EXT_MASK
++
+ #define BCM6368_RESET_SPI	SOFTRESET_6368_SPI_MASK
+ #define BCM6368_RESET_ENET	0
+ #define BCM6368_RESET_USBH	SOFTRESET_6368_USBH_MASK
+@@ -119,6 +133,10 @@ static const u32 bcm6358_reset_bits[] =
+ 	__GEN_RESET_BITS_TABLE(6358)
+ };
+ 
++static const u32 bcm6362_reset_bits[] = {
++	__GEN_RESET_BITS_TABLE(6362)
++};
++
+ static const u32 bcm6368_reset_bits[] = {
+ 	__GEN_RESET_BITS_TABLE(6368)
+ };
+@@ -140,6 +158,9 @@ static int __init bcm63xx_reset_bits_ini
+ 	} else if (BCMCPU_IS_6358()) {
+ 		reset_reg = PERF_SOFTRESET_6358_REG;
+ 		bcm63xx_reset_bits = bcm6358_reset_bits;
++	} else if (BCMCPU_IS_6362()) {
++		reset_reg = PERF_SOFTRESET_6362_REG;
++		bcm63xx_reset_bits = bcm6362_reset_bits;
+ 	} else if (BCMCPU_IS_6368()) {
+ 		reset_reg = PERF_SOFTRESET_6368_REG;
+ 		bcm63xx_reset_bits = bcm6368_reset_bits;
+@@ -182,6 +203,13 @@ static const u32 bcm63xx_reset_bits[] =
+ #define reset_reg PERF_SOFTRESET_6358_REG
+ #endif
+ 
++#ifdef CONFIG_BCM63XX_CPU_6362
++static const u32 bcm63xx_reset_bits[] = {
++	__GEN_RESET_BITS_TABLE(6362)
++};
++#define reset_reg PERF_SOFTRESET_6362_REG
++#endif
++
+ #ifdef CONFIG_BCM63XX_CPU_6368
+ static const u32 bcm63xx_reset_bits[] = {
+ 	__GEN_RESET_BITS_TABLE(6368)
+--- a/arch/mips/bcm63xx/setup.c
++++ b/arch/mips/bcm63xx/setup.c
+@@ -83,6 +83,9 @@ void bcm63xx_machine_reboot(void)
+ 	case BCM6358_CPU_ID:
+ 		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6358;
+ 		break;
++	case BCM6362_CPU_ID:
++		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6362;
++		break;
+ 	}
+ 
+ 	for (i = 0; i < 2; i++) {
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
+@@ -14,6 +14,7 @@
+ #define BCM6345_CPU_ID		0x6345
+ #define BCM6348_CPU_ID		0x6348
+ #define BCM6358_CPU_ID		0x6358
++#define BCM6362_CPU_ID		0x6362
+ #define BCM6368_CPU_ID		0x6368
+ 
+ void __init bcm63xx_cpu_init(void);
+@@ -86,6 +87,20 @@ unsigned int bcm63xx_get_cpu_freq(void);
+ # define BCMCPU_IS_6358()	(0)
+ #endif
+ 
++#ifdef CONFIG_BCM63XX_CPU_6362
++# ifdef bcm63xx_get_cpu_id
++#  undef bcm63xx_get_cpu_id
++#  define bcm63xx_get_cpu_id()	__bcm63xx_get_cpu_id()
++#  define BCMCPU_RUNTIME_DETECT
++# else
++#  define bcm63xx_get_cpu_id()	BCM6362_CPU_ID
++# endif
++# define BCMCPU_IS_6362()	(bcm63xx_get_cpu_id() == BCM6362_CPU_ID)
++#else
++# define BCMCPU_IS_6362()	(0)
++#endif
++
++
+ #ifdef CONFIG_BCM63XX_CPU_6368
+ # ifdef bcm63xx_get_cpu_id
+ #  undef bcm63xx_get_cpu_id
+@@ -413,6 +428,62 @@ enum bcm63xx_regs_set {
+ 
+ 
+ /*
++ * 6362 register sets base address
++ */
++#define BCM_6362_DSL_LMEM_BASE		(0xdeadbeef)
++#define BCM_6362_PERF_BASE		(0xb0000000)
++#define BCM_6362_TIMER_BASE		(0xb0000040)
++#define BCM_6362_WDT_BASE		(0xb000005c)
++#define BCM_6362_UART0_BASE             (0xb0000100)
++#define BCM_6362_UART1_BASE		(0xb0000120)
++#define BCM_6362_GPIO_BASE		(0xb0000080)
++#define BCM_6362_SPI_BASE		(0xb0000800)
++#define BCM_6362_HSSPI_BASE		(0xb0001000)
++#define BCM_6362_UDC0_BASE		(0xdeadbeef)
++#define BCM_6362_USBDMA_BASE		(0xb000c000)
++#define BCM_6362_OHCI0_BASE		(0xb0002600)
++#define BCM_6362_OHCI_PRIV_BASE		(0xdeadbeef)
++#define BCM_6362_USBH_PRIV_BASE		(0xb0002700)
++#define BCM_6362_USBD_BASE		(0xb0002400)
++#define BCM_6362_MPI_BASE		(0xdeadbeef)
++#define BCM_6362_PCMCIA_BASE		(0xdeadbeef)
++#define BCM_6362_PCIE_BASE		(0xb0e40000)
++#define BCM_6362_SDRAM_REGS_BASE	(0xdeadbeef)
++#define BCM_6362_DSL_BASE		(0xdeadbeef)
++#define BCM_6362_UBUS_BASE		(0xdeadbeef)
++#define BCM_6362_ENET0_BASE		(0xdeadbeef)
++#define BCM_6362_ENET1_BASE		(0xdeadbeef)
++#define BCM_6362_ENETDMA_BASE		(0xb000d800)
++#define BCM_6362_ENETDMAC_BASE		(0xb000da00)
++#define BCM_6362_ENETDMAS_BASE		(0xb000dc00)
++#define BCM_6362_ENETSW_BASE		(0xb0e00000)
++#define BCM_6362_EHCI0_BASE		(0xb0002500)
++#define BCM_6362_SDRAM_BASE		(0xdeadbeef)
++#define BCM_6362_MEMC_BASE		(0xdeadbeef)
++#define BCM_6362_DDR_BASE		(0xb0003000)
++#define BCM_6362_M2M_BASE		(0xdeadbeef)
++#define BCM_6362_ATM_BASE		(0xdeadbeef)
++#define BCM_6362_XTM_BASE		(0xb0007800)
++#define BCM_6362_XTMDMA_BASE		(0xb000b800)
++#define BCM_6362_XTMDMAC_BASE		(0xdeadbeef)
++#define BCM_6362_XTMDMAS_BASE		(0xdeadbeef)
++#define BCM_6362_PCM_BASE		(0xb000a800)
++#define BCM_6362_PCMDMA_BASE		(0xdeadbeef)
++#define BCM_6362_PCMDMAC_BASE		(0xdeadbeef)
++#define BCM_6362_PCMDMAS_BASE		(0xdeadbeef)
++#define BCM_6362_RNG_BASE		(0xdeadbeef)
++#define BCM_6362_MISC_BASE		(0xb0001800)
++
++#define BCM_6362_NAND_REG_BASE		(0xb0000200)
++#define BCM_6362_NAND_CACHE_BASE	(0xb0000600)
++#define BCM_6362_LED_BASE		(0xb0001900)
++#define BCM_6362_IPSEC_BASE		(0xb0002800)
++#define BCM_6362_IPSEC_DMA_BASE		(0xb000d000)
++#define BCM_6362_WLAN_CHIPCOMMON_BASE	(0xb0004000)
++#define BCM_6362_WLAN_D11_BASE		(0xb0005000)
++#define BCM_6362_WLAN_SHIM_BASE		(0xb0007000)
++
++/*
+  * 6368 register sets base address
+  */
+ #define BCM_6368_DSL_LMEM_BASE		(0xdeadbeef)
+@@ -574,6 +645,9 @@ static inline unsigned long bcm63xx_regs
+ #ifdef CONFIG_BCM63XX_CPU_6358
+ 	__GEN_RSET(6358)
+ #endif
++#ifdef CONFIG_BCM63XX_CPU_6362
++	__GEN_RSET(6362)
++#endif
+ #ifdef CONFIG_BCM63XX_CPU_6368
+ 	__GEN_RSET(6368)
+ #endif
+@@ -836,6 +910,71 @@ enum bcm63xx_irq {
+ #define BCM_6358_EXT_IRQ3		(IRQ_INTERNAL_BASE + 28)
+ 
+ /*
++ * 6362 irqs
++ */
++#define BCM_6362_HIGH_IRQ_BASE		(IRQ_INTERNAL_BASE + 32)
++
++#define BCM_6362_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
++#define BCM_6362_SPI_IRQ		(IRQ_INTERNAL_BASE + 2)
++#define BCM_6362_UART0_IRQ		(IRQ_INTERNAL_BASE + 3)
++#define BCM_6362_UART1_IRQ		(IRQ_INTERNAL_BASE + 4)
++#define BCM_6362_DSL_IRQ		(IRQ_INTERNAL_BASE + 28)
++#define BCM_6362_UDC0_IRQ		0
++#define BCM_6362_ENET0_IRQ		0
++#define BCM_6362_ENET1_IRQ		0
++#define BCM_6362_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 14)
++#define BCM_6362_HSSPI_IRQ		(IRQ_INTERNAL_BASE + 5)
++#define BCM_6362_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 9)
++#define BCM_6362_EHCI0_IRQ		(IRQ_INTERNAL_BASE + 10)
++#define BCM_6362_USBD_IRQ		(IRQ_INTERNAL_BASE + 11)
++#define BCM_6362_USBD_RXDMA0_IRQ	(IRQ_INTERNAL_BASE + 20)
++#define BCM_6362_USBD_TXDMA0_IRQ	(IRQ_INTERNAL_BASE + 21)
++#define BCM_6362_USBD_RXDMA1_IRQ	(IRQ_INTERNAL_BASE + 22)
++#define BCM_6362_USBD_TXDMA1_IRQ	(IRQ_INTERNAL_BASE + 23)
++#define BCM_6362_USBD_RXDMA2_IRQ	(IRQ_INTERNAL_BASE + 24)
++#define BCM_6362_USBD_TXDMA2_IRQ	(IRQ_INTERNAL_BASE + 25)
++#define BCM_6362_PCMCIA_IRQ		0
++#define BCM_6362_ENET0_RXDMA_IRQ	0
++#define BCM_6362_ENET0_TXDMA_IRQ	0
++#define BCM_6362_ENET1_RXDMA_IRQ	0
++#define BCM_6362_ENET1_TXDMA_IRQ	0
++#define BCM_6362_PCI_IRQ		(IRQ_INTERNAL_BASE + 30)
++#define BCM_6362_ATM_IRQ		0
++#define BCM_6362_ENETSW_RXDMA0_IRQ	(BCM_6362_HIGH_IRQ_BASE + 0)
++#define BCM_6362_ENETSW_RXDMA1_IRQ	(BCM_6362_HIGH_IRQ_BASE + 1)
++#define BCM_6362_ENETSW_RXDMA2_IRQ	(BCM_6362_HIGH_IRQ_BASE + 2)
++#define BCM_6362_ENETSW_RXDMA3_IRQ	(BCM_6362_HIGH_IRQ_BASE + 3)
++#define BCM_6362_ENETSW_TXDMA0_IRQ	0
++#define BCM_6362_ENETSW_TXDMA1_IRQ	0
++#define BCM_6362_ENETSW_TXDMA2_IRQ	0
++#define BCM_6362_ENETSW_TXDMA3_IRQ	0
++#define BCM_6362_XTM_IRQ		0
++#define BCM_6362_XTM_DMA0_IRQ		(BCM_6362_HIGH_IRQ_BASE + 12)
++
++#define BCM_6362_RING_OSC_IRQ		(IRQ_INTERNAL_BASE + 1)
++#define BCM_6362_WLAN_GPIO_IRQ		(IRQ_INTERNAL_BASE + 6)
++#define BCM_6362_WLAN_IRQ		(IRQ_INTERNAL_BASE + 7)
++#define BCM_6362_IPSEC_IRQ		(IRQ_INTERNAL_BASE + 8)
++#define BCM_6362_NAND_IRQ		(IRQ_INTERNAL_BASE + 12)
++#define BCM_6362_PCM_IRQ		(IRQ_INTERNAL_BASE + 13)
++#define BCM_6362_DG_IRQ			(IRQ_INTERNAL_BASE + 15)
++#define BCM_6362_EPHY_ENERGY0_IRQ	(IRQ_INTERNAL_BASE + 16)
++#define BCM_6362_EPHY_ENERGY1_IRQ	(IRQ_INTERNAL_BASE + 17)
++#define BCM_6362_EPHY_ENERGY2_IRQ	(IRQ_INTERNAL_BASE + 18)
++#define BCM_6362_EPHY_ENERGY3_IRQ	(IRQ_INTERNAL_BASE + 19)
++#define BCM_6362_IPSEC_DMA0_IRQ		(IRQ_INTERNAL_BASE + 26)
++#define BCM_6362_IPSEC_DMA1_IRQ		(IRQ_INTERNAL_BASE + 27)
++#define BCM_6362_FAP0_IRQ		(IRQ_INTERNAL_BASE + 29)
++#define BCM_6362_PCM_DMA0_IRQ		(BCM_6362_HIGH_IRQ_BASE + 4)
++#define BCM_6362_PCM_DMA1_IRQ		(BCM_6362_HIGH_IRQ_BASE + 5)
++#define BCM_6362_DECT0_IRQ		(BCM_6362_HIGH_IRQ_BASE + 6)
++#define BCM_6362_DECT1_IRQ		(BCM_6362_HIGH_IRQ_BASE + 7)
++#define BCM_6362_EXT_IRQ0		(BCM_6362_HIGH_IRQ_BASE + 8)
++#define BCM_6362_EXT_IRQ1		(BCM_6362_HIGH_IRQ_BASE + 9)
++#define BCM_6362_EXT_IRQ2		(BCM_6362_HIGH_IRQ_BASE + 10)
++#define BCM_6362_EXT_IRQ3		(BCM_6362_HIGH_IRQ_BASE + 11)
++
++/*
+  * 6368 irqs
+  */
+ #define BCM_6368_HIGH_IRQ_BASE		(IRQ_INTERNAL_BASE + 32)
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
+@@ -17,6 +17,8 @@ static inline unsigned long bcm63xx_gpio
+ 		return 8;
+ 	case BCM6345_CPU_ID:
+ 		return 16;
++	case BCM6362_CPU_ID:
++		return 48;
+ 	case BCM6368_CPU_ID:
+ 		return 38;
+ 	case BCM6348_CPU_ID:
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -112,6 +112,39 @@
+ 					CKCTL_6358_USBSU_EN |		\
+ 					CKCTL_6358_EPHY_EN)
+ 
++#define CKCTL_6362_ADSL_QPROC_EN	(1 << 1)
++#define CKCTL_6362_ADSL_AFE_EN		(1 << 2)
++#define CKCTL_6362_ADSL_EN		(1 << 3)
++#define CKCTL_6362_MIPS_EN		(1 << 4)
++#define CKCTL_6362_WLAN_OCP_EN		(1 << 5)
++#define CKCTL_6362_SWPKT_USB_EN		(1 << 7)
++#define CKCTL_6362_SWPKT_SAR_EN		(1 << 8)
++#define CKCTL_6362_SAR_EN		(1 << 9)
++#define CKCTL_6362_ROBOSW_EN		(1 << 10)
++#define CKCTL_6362_PCM_EN		(1 << 11)
++#define CKCTL_6362_USBD_EN		(1 << 12)
++#define CKCTL_6362_USBH_EN		(1 << 13)
++#define CKCTL_6362_IPSEC_EN		(1 << 14)
++#define CKCTL_6362_SPI_EN		(1 << 15)
++#define CKCTL_6362_HSSPI_EN		(1 << 16)
++#define CKCTL_6362_PCIE_EN		(1 << 17)
++#define CKCTL_6362_FAP_EN		(1 << 18)
++#define CKCTL_6362_PHYMIPS_EN		(1 << 19)
++#define CKCTL_6362_NAND_EN		(1 << 20)
++
++#define CKCTL_6362_ALL_SAFE_EN		(CKCTL_6362_PHYMIPS_EN |	\
++					CKCTL_6362_ADSL_QPROC_EN |	\
++					CKCTL_6362_ADSL_AFE_EN |	\
++					CKCTL_6362_ADSL_EN |		\
++					CKCTL_6362_SAR_EN  |		\
++					CKCTL_6362_PCM_EN  |		\
++					CKCTL_6362_IPSEC_EN |		\
++					CKCTL_6362_USBD_EN |		\
++					CKCTL_6362_USBH_EN |		\
++					CKCTL_6362_ROBOSW_EN |		\
++					CKCTL_6362_PCIE_EN)
++
++
+ #define CKCTL_6368_VDSL_QPROC_EN	(1 << 2)
+ #define CKCTL_6368_VDSL_AFE_EN		(1 << 3)
+ #define CKCTL_6368_VDSL_BONDING_EN	(1 << 4)
+@@ -153,6 +186,7 @@
+ #define PERF_IRQMASK_6345_REG		0xc
+ #define PERF_IRQMASK_6348_REG		0xc
+ #define PERF_IRQMASK_6358_REG		0xc
++#define PERF_IRQMASK_6362_REG		0x20
+ #define PERF_IRQMASK_6368_REG		0x20
+ 
+ /* Interrupt Status register */
+@@ -161,6 +195,7 @@
+ #define PERF_IRQSTAT_6345_REG		0x10
+ #define PERF_IRQSTAT_6348_REG		0x10
+ #define PERF_IRQSTAT_6358_REG		0x10
++#define PERF_IRQSTAT_6362_REG		0x28
+ #define PERF_IRQSTAT_6368_REG		0x28
+ 
+ /* External Interrupt Configuration register */
+@@ -169,6 +204,7 @@
+ #define PERF_EXTIRQ_CFG_REG_6345	0x14
+ #define PERF_EXTIRQ_CFG_REG_6348	0x14
+ #define PERF_EXTIRQ_CFG_REG_6358	0x14
++#define PERF_EXTIRQ_CFG_REG_6362	0x18
+ #define PERF_EXTIRQ_CFG_REG_6368	0x18
+ 
+ #define PERF_EXTIRQ_CFG_REG2_6368	0x1c
+@@ -197,6 +233,7 @@
+ #define PERF_SOFTRESET_REG		0x28
+ #define PERF_SOFTRESET_6328_REG		0x10
+ #define PERF_SOFTRESET_6358_REG		0x34
++#define PERF_SOFTRESET_6362_REG		0x10
+ #define PERF_SOFTRESET_6368_REG		0x10
+ 
+ #define SOFTRESET_6328_SPI_MASK		(1 << 0)
+@@ -259,6 +296,22 @@
+ #define SOFTRESET_6358_PCM_MASK		(1 << 13)
+ #define SOFTRESET_6358_ADSL_MASK	(1 << 14)
+ 
++#define SOFTRESET_6362_SPI_MASK		(1 << 0)
++#define SOFTRESET_6362_IPSEC_MASK	(1 << 1)
++#define SOFTRESET_6362_EPHY_MASK	(1 << 2)
++#define SOFTRESET_6362_SAR_MASK		(1 << 3)
++#define SOFTRESET_6362_ENETSW_MASK	(1 << 4)
++#define SOFTRESET_6362_USBS_MASK	(1 << 5)
++#define SOFTRESET_6362_USBH_MASK	(1 << 6)
++#define SOFTRESET_6362_PCM_MASK		(1 << 7)
++#define SOFTRESET_6362_PCIE_CORE_MASK	(1 << 8)
++#define SOFTRESET_6362_PCIE_MASK	(1 << 9)
++#define SOFTRESET_6362_PCIE_EXT_MASK	(1 << 10)
++#define SOFTRESET_6362_WLAN_SHIM_MASK	(1 << 11)
++#define SOFTRESET_6362_DDR_PHY_MASK	(1 << 12)
++#define SOFTRESET_6362_FAP_MASK		(1 << 13)
++#define SOFTRESET_6362_WLAN_UBUS_MASK	(1 << 14)
++
+ #define SOFTRESET_6368_SPI_MASK		(1 << 0)
+ #define SOFTRESET_6368_MPI_MASK		(1 << 3)
+ #define SOFTRESET_6368_EPHY_MASK	(1 << 6)
+@@ -1352,6 +1405,12 @@
+ #define SERDES_PCIE_EN			(1 << 0)
+ #define SERDES_PCIE_EXD_EN		(1 << 15)
+ 
++#define MISC_STRAPBUS_6362_REG		0x14
++#define STRAPBUS_6362_FCVO_SHIFT	1
++#define STRAPBUS_6362_FCVO_MASK		(0x1f << STRAPBUS_6362_FCVO_SHIFT)
++#define STRAPBUS_6362_BOOT_SEL_SERIAL	(1 << 15)
++#define STRAPBUS_6362_BOOT_SEL_NAND	(0 << 15)
++
+ #define MISC_STRAPBUS_6328_REG		0x240
+ #define STRAPBUS_6328_FCVO_SHIFT	7
+ #define STRAPBUS_6328_FCVO_MASK		(0x1f << STRAPBUS_6328_FCVO_SHIFT)
+--- a/arch/mips/include/asm/mach-bcm63xx/ioremap.h
++++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h
+@@ -19,6 +19,7 @@ static inline int is_bcm63xx_internal_re
+ 			return 1;
+ 		break;
+ 	case BCM6328_CPU_ID:
++	case BCM6362_CPU_ID:
+ 	case BCM6368_CPU_ID:
+ 		if (offset >= 0xb0000000 && offset < 0xb1000000)
+ 			return 1;

target/linux/brcm63xx/patches-3.8/313-MIPS-BCM63XX-enable-pcie-for-BCM6362.patch

@@ -0,0 +1,52 @@
+From 2f94c414e554531e2a65a7c4a7fa2d1ba0380c0a Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Mon, 21 Nov 2011 00:53:26 +0100
+Subject: [PATCH 29/72] MIPS: BCM63XX: enable pcie for BCM6362
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/pci/pci-bcm63xx.c |   19 ++++++++++++++++---
+ 1 file changed, 16 insertions(+), 3 deletions(-)
+
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -1401,7 +1401,8 @@
+ /*************************************************************************
+  * _REG relative to RSET_MISC
+  *************************************************************************/
+-#define MISC_SERDES_CTRL_REG		0x0
++#define MISC_SERDES_CTRL_6328_REG	0x0
++#define MISC_SERDES_CTRL_6362_REG	0x4
+ #define SERDES_PCIE_EN			(1 << 0)
+ #define SERDES_PCIE_EXD_EN		(1 << 15)
+ 
+--- a/arch/mips/pci/pci-bcm63xx.c
++++ b/arch/mips/pci/pci-bcm63xx.c
+@@ -121,11 +121,17 @@ void __iomem *pci_iospace_start;
+ static void __init bcm63xx_reset_pcie(void)
+ {
+ 	u32 val;
++	u32 reg;
+ 
+ 	/* enable SERDES */
+-	val = bcm_misc_readl(MISC_SERDES_CTRL_REG);
++	if (BCMCPU_IS_6328())
++		reg = MISC_SERDES_CTRL_6328_REG;
++	else
++		reg = MISC_SERDES_CTRL_6362_REG;
++
++	val = bcm_misc_readl(reg);
+ 	val |= SERDES_PCIE_EN | SERDES_PCIE_EXD_EN;
+-	bcm_misc_writel(val, MISC_SERDES_CTRL_REG);
++	bcm_misc_writel(val, reg);
+ 
+ 	/* reset the PCIe core */
+ 	bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 1);
+@@ -330,6 +336,7 @@ static int __init bcm63xx_pci_init(void)
+ 
+ 	switch (bcm63xx_get_cpu_id()) {
+ 	case BCM6328_CPU_ID:
++	case BCM6362_CPU_ID:
+ 		return bcm63xx_register_pcie();
+ 	case BCM6348_CPU_ID:
+ 	case BCM6358_CPU_ID:

target/linux/brcm63xx/patches-3.8/404-bcm963xx_flashmap.patch

@@ -0,0 +1,65 @@
+From a4d005c91d403d9f3d0272db6cc46202c06ec774 Mon Sep 17 00:00:00 2001
+From: Axel Gembe <ago@bastart.eu.org>
+Date: Mon, 12 May 2008 18:54:09 +0200
+Subject: [PATCH] bcm963xx: flashmap support
+
+Signed-off-by: Axel Gembe <ago@bastart.eu.org>
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c |   19 +----------------
+ drivers/mtd/maps/bcm963xx-flash.c         |   32 ++++++++++++++++++++++++----
+ drivers/mtd/redboot.c                     |   13 +++++++++--
+ 3 files changed, 38 insertions(+), 26 deletions(-)
+
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -30,7 +30,7 @@ static struct mtd_partition mtd_partitio
+ 	}
+ };
+ 
+-static const char *bcm63xx_part_types[] = { "bcm63xxpart", NULL };
++static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL };
+ 
+ static struct physmap_flash_data flash_data = {
+ 	.width			= 2,
+--- a/drivers/mtd/redboot.c
++++ b/drivers/mtd/redboot.c
+@@ -72,6 +72,7 @@ static int parse_redboot_partitions(stru
+ 	int nulllen = 0;
+ 	int numslots;
+ 	unsigned long offset;
++	unsigned long fis_origin = 0;
+ #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
+ 	static char nullstring[] = "unallocated";
+ #endif
+@@ -176,6 +177,16 @@ static int parse_redboot_partitions(stru
+ 		goto out;
+ 	}
+ 
++	if (data && data->origin) {
++		fis_origin = data->origin;
++	} else {
++		for (i = 0; i < numslots; i++) {
++			if (!strncmp(buf[i].name, "RedBoot", 8)) {
++				fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
++			}
++		}
++	}
++
+ 	for (i = 0; i < numslots; i++) {
+ 		struct fis_list *new_fl, **prev;
+ 
+@@ -196,10 +207,10 @@ static int parse_redboot_partitions(stru
+ 			goto out;
+ 		}
+ 		new_fl->img = &buf[i];
+-		if (data && data->origin)
+-			buf[i].flash_base -= data->origin;
+-		else
+-			buf[i].flash_base &= master->size-1;
++		if (fis_origin)
++			buf[i].flash_base -= fis_origin;
++
++		buf[i].flash_base &= (master->size << 1) - 1;
+ 
+ 		/* I'm sure the JFFS2 code has done me permanent damage.
+ 		 * I now think the following is _normal_

target/linux/brcm63xx/patches-3.8/405-bcm963xx_real_rootfs_length.patch

@@ -0,0 +1,27 @@
+--- a/include/uapi/linux/bcm963xx_tag.h
++++ b/include/uapi/linux/bcm963xx_tag.h
+@@ -85,8 +85,10 @@ struct bcm_tag {
+ 	__u32 rootfs_crc;
+ 	/* 224-227: CRC32 of kernel partition */
+ 	__u32 kernel_crc;
+-	/* 228-235: Unused at present */
+-	char reserved1[8];
++	/* 228-231: Image sequence number */
++	char image_sequence[4];
++	/* 222-235: Openwrt: real rootfs length */
++	__u32 real_rootfs_length;
+ 	/* 236-239: CRC32 of header excluding last 20 bytes */
+ 	__u32 header_crc;
+ 	/* 240-255: Unused at present */
+--- a/drivers/mtd/bcm63xxpart.c
++++ b/drivers/mtd/bcm63xxpart.c
+@@ -131,7 +131,8 @@ static int bcm63xx_parse_cfe_partitions(
+ 		} else {
+ 			/* OpenWrt layout */
+ 			rootfsaddr = kerneladdr + kernellen;
+-			rootfslen = spareaddr - rootfsaddr;
++			rootfslen = buf->real_rootfs_length;
++			spareaddr = rootfsaddr + rootfslen;
+ 		}
+ 	} else {
+ 		pr_warn("CFE boot tag CRC invalid (expected %08x, actual %08x)\n",

target/linux/brcm63xx/patches-3.8/406_bcm63xx_enet_vlan_incoming_fixed.patch

@@ -0,0 +1,11 @@
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -1515,7 +1515,7 @@ static int compute_hw_mtu(struct bcm_ene
+ 	actual_mtu = mtu;
+ 
+ 	/* add ethernet header + vlan tag size */
+-	actual_mtu += VLAN_ETH_HLEN;
++	actual_mtu += VLAN_ETH_HLEN + VLAN_HLEN;
+ 
+ 	if (actual_mtu < 64 || actual_mtu > BCMENET_MAX_MTU)
+ 		return -EINVAL;

target/linux/brcm63xx/patches-3.8/408-6358-enet1-external-mii-clk.patch

@@ -0,0 +1,22 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -862,6 +862,8 @@ void __init board_prom_init(void)
+ 		if (BCMCPU_IS_6348())
+ 			val |= GPIO_MODE_6348_G3_EXT_MII |
+ 				GPIO_MODE_6348_G0_EXT_MII;
++		else if (BCMCPU_IS_6358())
++			val |= GPIO_MODE_6358_ENET1_MII_CLK_INV;
+ 	}
+ 
+ 	bcm_gpio_writel(val, GPIO_MODE_REG);
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -578,6 +578,8 @@
+ #define GPIO_MODE_6358_EXTRA_SPI_SS	(1 << 7)
+ #define GPIO_MODE_6358_SERIAL_LED	(1 << 10)
+ #define GPIO_MODE_6358_UTOPIA		(1 << 12)
++#define GPIO_MODE_6358_ENET1_MII_CLK_INV (1 << 30)
++#define GPIO_MODE_6358_ENET0_MII_CLK_INV (1 << 31)
+ 
+ #define GPIO_MODE_6368_ANALOG_AFE_0	(1 << 0)
+ #define GPIO_MODE_6368_ANALOG_AFE_1	(1 << 1)

target/linux/brcm63xx/patches-3.8/410-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch

@@ -0,0 +1,169 @@
+From b11218c750ab92cfab4408a0328f1b36ceec3f33 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 6 Jan 2012 12:24:18 +0100
+Subject: [PATCH 19/63] NET: bcm63xx_enet: move phy_(dis)connect into probe/remove
+
+Only connect/disconnect the phy during probe and remove, not during any
+open/close. The phy seldom changes during the runtime, and disconnecting
+the phy during close will prevent it from keeping any configuration over
+a down/up cycle.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c |   84 +++++++++++++-------------
+ 1 files changed, 41 insertions(+), 43 deletions(-)
+
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -784,10 +784,8 @@ static int bcm_enet_open(struct net_devi
+ 	struct bcm_enet_priv *priv;
+ 	struct sockaddr addr;
+ 	struct device *kdev;
+-	struct phy_device *phydev;
+ 	int i, ret;
+ 	unsigned int size;
+-	char phy_id[MII_BUS_ID_SIZE + 3];
+ 	void *p;
+ 	u32 val;
+ 
+@@ -795,40 +793,10 @@ static int bcm_enet_open(struct net_devi
+ 	kdev = &priv->pdev->dev;
+ 
+ 	if (priv->has_phy) {
+-		/* connect to PHY */
+-		snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT,
+-			 priv->mii_bus->id, priv->phy_id);
+-
+-		phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, 0,
+-				     PHY_INTERFACE_MODE_MII);
+-
+-		if (IS_ERR(phydev)) {
+-			dev_err(kdev, "could not attach to PHY\n");
+-			return PTR_ERR(phydev);
+-		}
+-
+-		/* mask with MAC supported features */
+-		phydev->supported &= (SUPPORTED_10baseT_Half |
+-				      SUPPORTED_10baseT_Full |
+-				      SUPPORTED_100baseT_Half |
+-				      SUPPORTED_100baseT_Full |
+-				      SUPPORTED_Autoneg |
+-				      SUPPORTED_Pause |
+-				      SUPPORTED_MII);
+-		phydev->advertising = phydev->supported;
+-
+-		if (priv->pause_auto && priv->pause_rx && priv->pause_tx)
+-			phydev->advertising |= SUPPORTED_Pause;
+-		else
+-			phydev->advertising &= ~SUPPORTED_Pause;
+-
+-		dev_info(kdev, "attached PHY at address %d [%s]\n",
+-			 phydev->addr, phydev->drv->name);
+-
++		/* Reset state */
+ 		priv->old_link = 0;
+ 		priv->old_duplex = -1;
+ 		priv->old_pause = -1;
+-		priv->phydev = phydev;
+ 	}
+ 
+ 	/* mask all interrupts and request them */
+@@ -838,7 +806,7 @@ static int bcm_enet_open(struct net_devi
+ 
+ 	ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev);
+ 	if (ret)
+-		goto out_phy_disconnect;
++		return ret;
+ 
+ 	ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, IRQF_DISABLED,
+ 			  dev->name, dev);
+@@ -1025,9 +993,6 @@ out_freeirq_rx:
+ out_freeirq:
+ 	free_irq(dev->irq, dev);
+ 
+-out_phy_disconnect:
+-	phy_disconnect(priv->phydev);
+-
+ 	return ret;
+ }
+ 
+@@ -1132,12 +1097,6 @@ static int bcm_enet_stop(struct net_devi
+ 	free_irq(priv->irq_rx, dev);
+ 	free_irq(dev->irq, dev);
+ 
+-	/* release phy */
+-	if (priv->has_phy) {
+-		phy_disconnect(priv->phydev);
+-		priv->phydev = NULL;
+-	}
+-
+ 	return 0;
+ }
+ 
+@@ -1714,6 +1673,8 @@ static int bcm_enet_probe(struct platfor
+ 
+ 	/* MII bus registration */
+ 	if (priv->has_phy) {
++		struct phy_device *phydev;
++		char phy_id[MII_BUS_ID_SIZE + 3];
+ 
+ 		priv->mii_bus = mdiobus_alloc();
+ 		if (!priv->mii_bus) {
+@@ -1750,6 +1711,38 @@ static int bcm_enet_probe(struct platfor
+ 			dev_err(&pdev->dev, "unable to register mdio bus\n");
+ 			goto out_free_mdio;
+ 		}
++
++		/* connect to PHY */
++		snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT,
++			 priv->mii_bus->id, priv->phy_id);
++
++		phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, 0,
++				     PHY_INTERFACE_MODE_MII);
++
++		if (IS_ERR(phydev)) {
++			dev_err(&pdev->dev, "could not attach to PHY\n");
++			goto out_unregister_mdio;
++		}
++
++		/* mask with MAC supported features */
++		phydev->supported &= (SUPPORTED_10baseT_Half |
++				      SUPPORTED_10baseT_Full |
++				      SUPPORTED_100baseT_Half |
++				      SUPPORTED_100baseT_Full |
++				      SUPPORTED_Autoneg |
++				      SUPPORTED_Pause |
++				      SUPPORTED_MII);
++		phydev->advertising = phydev->supported;
++
++		if (priv->pause_auto && priv->pause_rx && priv->pause_tx)
++			phydev->advertising |= SUPPORTED_Pause;
++		else
++			phydev->advertising &= ~SUPPORTED_Pause;
++
++		dev_info(&pdev->dev, "attached PHY at address %d [%s]\n",
++			 phydev->addr, phydev->drv->name);
++
++		priv->phydev = phydev;
+ 	} else {
+ 
+ 		/* run platform code to initialize PHY device */
+@@ -1795,6 +1788,9 @@ static int bcm_enet_probe(struct platfor
+ 	return 0;
+ 
+ out_unregister_mdio:
++	if (priv->phydev)
++		phy_disconnect(priv->phydev);
++
+ 	if (priv->mii_bus) {
+ 		mdiobus_unregister(priv->mii_bus);
+ 		kfree(priv->mii_bus->irq);
+@@ -1845,6 +1841,8 @@ static int bcm_enet_remove(struct platfo
+ 	enet_writel(priv, 0, ENET_MIISC_REG);
+ 
+ 	if (priv->has_phy) {
++		phy_disconnect(priv->phydev);
++		priv->phydev = NULL;
+ 		mdiobus_unregister(priv->mii_bus);
+ 		kfree(priv->mii_bus->irq);
+ 		mdiobus_free(priv->mii_bus);

target/linux/brcm63xx/patches-3.8/411-bcm63xx_enet-implement-reset_autoneg-ethtool.patch

@@ -0,0 +1,40 @@
+From accc558f334662c8b16c121b4819931c028e8eb0 Mon Sep 17 00:00:00 2001
+From: Maxime Bizon <mbizon@freebox.fr>
+Date: Mon, 8 Jun 2009 16:12:10 +0200
+Subject: [PATCH 27/63] bcm63xx_enet: implement reset_autoneg ethtool.
+
+---
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c |   15 +++++++++++++++
+ 1 files changed, 15 insertions(+), 0 deletions(-)
+
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -1290,6 +1290,20 @@ static void bcm_enet_get_ethtool_stats(s
+ 	mutex_unlock(&priv->mib_update_lock);
+ }
+ 
++static int bcm_enet_nway_reset(struct net_device *dev)
++{
++	struct bcm_enet_priv *priv;
++
++	priv = netdev_priv(dev);
++	if (priv->has_phy) {
++		if (!priv->phydev)
++			return -ENODEV;
++		return genphy_restart_aneg(priv->phydev);
++	}
++
++	return -EOPNOTSUPP;
++}
++
+ static int bcm_enet_get_settings(struct net_device *dev,
+ 				 struct ethtool_cmd *cmd)
+ {
+@@ -1432,6 +1446,7 @@ static const struct ethtool_ops bcm_enet
+ 	.get_strings		= bcm_enet_get_strings,
+ 	.get_sset_count		= bcm_enet_get_sset_count,
+ 	.get_ethtool_stats      = bcm_enet_get_ethtool_stats,
++	.nway_reset		= bcm_enet_nway_reset,
+ 	.get_settings		= bcm_enet_get_settings,
+ 	.set_settings		= bcm_enet_set_settings,
+ 	.get_drvinfo		= bcm_enet_get_drvinfo,

target/linux/brcm63xx/patches-3.8/412-bcm63xx_enet-use-resource_size.patch

@@ -0,0 +1,69 @@
+From dbd9b51204aa4114756b8659e180139ef3878032 Mon Sep 17 00:00:00 2001
+From: Maxime Bizon <mbizon@freebox.fr>
+Date: Thu, 21 Jan 2010 17:28:36 +0100
+Subject: [PATCH 28/63] bcm63xx_enet: use resource_size().
+
+---
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c |   18 ++++++++----------
+ 1 files changed, 8 insertions(+), 10 deletions(-)
+
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -1594,7 +1594,6 @@ static int bcm_enet_probe(struct platfor
+ 	struct resource *res_mem, *res_irq, *res_irq_rx, *res_irq_tx;
+ 	struct mii_bus *bus;
+ 	const char *clk_name;
+-	unsigned int iomem_size;
+ 	int i, ret;
+ 
+ 	/* stop if shared driver failed, assume driver->probe will be
+@@ -1619,13 +1618,13 @@ static int bcm_enet_probe(struct platfor
+ 	if (ret)
+ 		goto out;
+ 
+-	iomem_size = resource_size(res_mem);
+-	if (!request_mem_region(res_mem->start, iomem_size, "bcm63xx_enet")) {
++	if (!request_mem_region(res_mem->start, resource_size(res_mem),
++				"bcm63xx_enet")) {
+ 		ret = -EBUSY;
+ 		goto out;
+ 	}
+ 
+-	priv->base = ioremap(res_mem->start, iomem_size);
++	priv->base = ioremap(res_mem->start, resource_size(res_mem));
+ 	if (priv->base == NULL) {
+ 		ret = -ENOMEM;
+ 		goto out_release_mem;
+@@ -1831,7 +1830,7 @@ out_unmap:
+ 	iounmap(priv->base);
+ 
+ out_release_mem:
+-	release_mem_region(res_mem->start, iomem_size);
++	release_mem_region(res_mem->start, resource_size(res_mem));
+ out:
+ 	free_netdev(dev);
+ 	return ret;
+@@ -1903,19 +1902,18 @@ struct platform_driver bcm63xx_enet_driv
+ static int bcm_enet_shared_probe(struct platform_device *pdev)
+ {
+ 	struct resource *res;
+-	unsigned int iomem_size;
+ 
+ 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ 	if (!res)
+ 		return -ENODEV;
+ 
+-	iomem_size = resource_size(res);
+-	if (!request_mem_region(res->start, iomem_size, "bcm63xx_enet_dma"))
++	if (!request_mem_region(res->start, resource_size(res),
++				"bcm63xx_enet_dma"))
+ 		return -EBUSY;
+ 
+-	bcm_enet_shared_base = ioremap(res->start, iomem_size);
++	bcm_enet_shared_base = ioremap(res->start, resource_size(res));
+ 	if (!bcm_enet_shared_base) {
+-		release_mem_region(res->start, iomem_size);
++		release_mem_region(res->start, resource_size(res));
+ 		return -ENOMEM;
+ 	}
+ 	return 0;

target/linux/brcm63xx/patches-3.8/413-bcm63xx_enet-disable-clock-when-uninitializing-devic.patch

@@ -0,0 +1,20 @@
+From fd15ecd10c95480be5635f8993b781fe3a1527c2 Mon Sep 17 00:00:00 2001
+From: Maxime Bizon <mbizon@freebox.fr>
+Date: Fri, 29 Apr 2011 16:54:50 +0200
+Subject: [PATCH 29/63] bcm63xx_enet: disable clock when uninitializing device.
+
+---
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c |    2 ++
+ 1 files changed, 2 insertions(+), 0 deletions(-)
+
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -1870,6 +1870,8 @@ static int bcm_enet_remove(struct platfo
+ 	}
+ 
+ 	/* release device resources */
++	clk_disable(priv->mac_clk);
++	clk_put(priv->mac_clk);
+ 	iounmap(priv->base);
+ 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ 	release_mem_region(res->start, resource_size(res));

target/linux/brcm63xx/patches-3.8/414-bcm63xx_enet-split-dma-registers-access.patch

@@ -0,0 +1,381 @@
+From 305579c1f946ed1aa6c125252ace21c53d47c11d Mon Sep 17 00:00:00 2001
+From: Maxime Bizon <mbizon@freebox.fr>
+Date: Thu, 21 Jan 2010 17:50:54 +0100
+Subject: [PATCH 30/63] bcm63xx_enet: split dma registers access.
+
+---
+ arch/mips/bcm63xx/dev-enet.c                     |   23 +++-
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h |    4 +-
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c     |  179 ++++++++++++++--------
+ 3 files changed, 138 insertions(+), 68 deletions(-)
+
+--- a/arch/mips/bcm63xx/dev-enet.c
++++ b/arch/mips/bcm63xx/dev-enet.c
+@@ -19,6 +19,16 @@ static struct resource shared_res[] = {
+ 		.end		= -1, /* filled at runtime */
+ 		.flags		= IORESOURCE_MEM,
+ 	},
++	{
++		.start		= -1, /* filled at runtime */
++		.end		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_MEM,
++	},
++	{
++		.start		= -1, /* filled at runtime */
++		.end		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_MEM,
++	},
+ };
+ 
+ static struct platform_device bcm63xx_enet_shared_device = {
+@@ -110,10 +120,15 @@ int __init bcm63xx_enet_register(int uni
+ 	if (!shared_device_registered) {
+ 		shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA);
+ 		shared_res[0].end = shared_res[0].start;
+-		if (BCMCPU_IS_6338())
+-			shared_res[0].end += (RSET_ENETDMA_SIZE / 2)  - 1;
+-		else
+-			shared_res[0].end += (RSET_ENETDMA_SIZE)  - 1;
++		shared_res[0].end += (RSET_ENETDMA_SIZE)  - 1;
++
++		shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC);
++		shared_res[1].end = shared_res[1].start;
++		shared_res[1].end += RSET_ENETDMAC_SIZE(16)  - 1;
++
++		shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS);
++		shared_res[2].end = shared_res[2].start;
++		shared_res[2].end += RSET_ENETDMAS_SIZE(16)  - 1;
+ 
+ 		ret = platform_device_register(&bcm63xx_enet_shared_device);
+ 		if (ret)
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
+@@ -174,7 +174,9 @@ enum bcm63xx_regs_set {
+ #define BCM_6358_RSET_SPI_SIZE		1804
+ #define BCM_6368_RSET_SPI_SIZE		1804
+ #define RSET_ENET_SIZE			2048
+-#define RSET_ENETDMA_SIZE		2048
++#define RSET_ENETDMA_SIZE		256
++#define RSET_ENETDMAC_SIZE(chans)	(16 * (chans))
++#define RSET_ENETDMAS_SIZE(chans)	(16 * (chans))
+ #define RSET_ENETSW_SIZE		65536
+ #define RSET_UART_SIZE			24
+ #define RSET_HSSPI_SIZE			1536
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -41,8 +41,8 @@ static int copybreak __read_mostly = 128
+ module_param(copybreak, int, 0);
+ MODULE_PARM_DESC(copybreak, "Receive copy threshold");
+ 
+-/* io memory shared between all devices */
+-static void __iomem *bcm_enet_shared_base;
++/* io registers memory shared between all devices */
++static void __iomem *bcm_enet_shared_base[3];
+ 
+ /*
+  * io helpers to access mac registers
+@@ -63,13 +63,35 @@ static inline void enet_writel(struct bc
+  */
+ static inline u32 enet_dma_readl(struct bcm_enet_priv *priv, u32 off)
+ {
+-	return bcm_readl(bcm_enet_shared_base + off);
++	return bcm_readl(bcm_enet_shared_base[0] + off);
+ }
+ 
+ static inline void enet_dma_writel(struct bcm_enet_priv *priv,
+ 				       u32 val, u32 off)
+ {
+-	bcm_writel(val, bcm_enet_shared_base + off);
++	bcm_writel(val, bcm_enet_shared_base[0] + off);
++}
++
++static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off)
++{
++	return bcm_readl(bcm_enet_shared_base[1] + off);
++}
++
++static inline void enet_dmac_writel(struct bcm_enet_priv *priv,
++				       u32 val, u32 off)
++{
++	bcm_writel(val, bcm_enet_shared_base[1] + off);
++}
++
++static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off)
++{
++	return bcm_readl(bcm_enet_shared_base[2] + off);
++}
++
++static inline void enet_dmas_writel(struct bcm_enet_priv *priv,
++				       u32 val, u32 off)
++{
++	bcm_writel(val, bcm_enet_shared_base[2] + off);
+ }
+ 
+ /*
+@@ -353,8 +375,8 @@ static int bcm_enet_receive_queue(struct
+ 		bcm_enet_refill_rx(dev);
+ 
+ 		/* kick rx dma */
+-		enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
+-				ENETDMA_CHANCFG_REG(priv->rx_chan));
++		enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
++				 ENETDMAC_CHANCFG_REG(priv->rx_chan));
+ 	}
+ 
+ 	return processed;
+@@ -429,10 +451,10 @@ static int bcm_enet_poll(struct napi_str
+ 	dev = priv->net_dev;
+ 
+ 	/* ack interrupts */
+-	enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
+-			ENETDMA_IR_REG(priv->rx_chan));
+-	enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
+-			ENETDMA_IR_REG(priv->tx_chan));
++	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
++			 ENETDMAC_IR_REG(priv->rx_chan));
++	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
++			 ENETDMAC_IR_REG(priv->tx_chan));
+ 
+ 	/* reclaim sent skb */
+ 	tx_work_done = bcm_enet_tx_reclaim(dev, 0);
+@@ -451,10 +473,10 @@ static int bcm_enet_poll(struct napi_str
+ 	napi_complete(napi);
+ 
+ 	/* restore rx/tx interrupt */
+-	enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
+-			ENETDMA_IRMASK_REG(priv->rx_chan));
+-	enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
+-			ENETDMA_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
++			 ENETDMAC_IRMASK_REG(priv->rx_chan));
++	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
++			 ENETDMAC_IRMASK_REG(priv->tx_chan));
+ 
+ 	return rx_work_done;
+ }
+@@ -497,8 +519,8 @@ static irqreturn_t bcm_enet_isr_dma(int
+ 	priv = netdev_priv(dev);
+ 
+ 	/* mask rx/tx interrupts */
+-	enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
+-	enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
+ 
+ 	napi_schedule(&priv->napi);
+ 
+@@ -557,8 +579,8 @@ static int bcm_enet_start_xmit(struct sk
+ 	wmb();
+ 
+ 	/* kick tx dma */
+-	enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
+-			ENETDMA_CHANCFG_REG(priv->tx_chan));
++	enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
++			 ENETDMAC_CHANCFG_REG(priv->tx_chan));
+ 
+ 	/* stop queue if no more desc available */
+ 	if (!priv->tx_desc_count)
+@@ -801,8 +823,8 @@ static int bcm_enet_open(struct net_devi
+ 
+ 	/* mask all interrupts and request them */
+ 	enet_writel(priv, 0, ENET_IRMASK_REG);
+-	enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
+-	enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
+ 
+ 	ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev);
+ 	if (ret)
+@@ -891,28 +913,28 @@ static int bcm_enet_open(struct net_devi
+ 	}
+ 
+ 	/* write rx & tx ring addresses */
+-	enet_dma_writel(priv, priv->rx_desc_dma,
+-			ENETDMA_RSTART_REG(priv->rx_chan));
+-	enet_dma_writel(priv, priv->tx_desc_dma,
+-			ENETDMA_RSTART_REG(priv->tx_chan));
++	enet_dmas_writel(priv, priv->rx_desc_dma,
++			 ENETDMAS_RSTART_REG(priv->rx_chan));
++	enet_dmas_writel(priv, priv->tx_desc_dma,
++			 ENETDMAS_RSTART_REG(priv->tx_chan));
+ 
+ 	/* clear remaining state ram for rx & tx channel */
+-	enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->rx_chan));
+-	enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->tx_chan));
+-	enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->rx_chan));
+-	enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->tx_chan));
+-	enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->rx_chan));
+-	enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->tx_chan));
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan));
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan));
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan));
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan));
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan));
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan));
+ 
+ 	/* set max rx/tx length */
+ 	enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG);
+ 	enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG);
+ 
+ 	/* set dma maximum burst len */
+-	enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
+-			ENETDMA_MAXBURST_REG(priv->rx_chan));
+-	enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
+-			ENETDMA_MAXBURST_REG(priv->tx_chan));
++	enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
++			 ENETDMAC_MAXBURST_REG(priv->rx_chan));
++	enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
++			 ENETDMAC_MAXBURST_REG(priv->tx_chan));
+ 
+ 	/* set correct transmit fifo watermark */
+ 	enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG);
+@@ -930,26 +952,26 @@ static int bcm_enet_open(struct net_devi
+ 	val |= ENET_CTL_ENABLE_MASK;
+ 	enet_writel(priv, val, ENET_CTL_REG);
+ 	enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG);
+-	enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
+-			ENETDMA_CHANCFG_REG(priv->rx_chan));
++	enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
++			 ENETDMAC_CHANCFG_REG(priv->rx_chan));
+ 
+ 	/* watch "mib counters about to overflow" interrupt */
+ 	enet_writel(priv, ENET_IR_MIB, ENET_IR_REG);
+ 	enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG);
+ 
+ 	/* watch "packet transferred" interrupt in rx and tx */
+-	enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
+-			ENETDMA_IR_REG(priv->rx_chan));
+-	enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
+-			ENETDMA_IR_REG(priv->tx_chan));
++	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
++			 ENETDMAC_IR_REG(priv->rx_chan));
++	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
++			 ENETDMAC_IR_REG(priv->tx_chan));
+ 
+ 	/* make sure we enable napi before rx interrupt  */
+ 	napi_enable(&priv->napi);
+ 
+-	enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
+-			ENETDMA_IRMASK_REG(priv->rx_chan));
+-	enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
+-			ENETDMA_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
++			 ENETDMAC_IRMASK_REG(priv->rx_chan));
++	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
++			 ENETDMAC_IRMASK_REG(priv->tx_chan));
+ 
+ 	if (priv->has_phy)
+ 		phy_start(priv->phydev);
+@@ -1026,14 +1048,14 @@ static void bcm_enet_disable_dma(struct
+ {
+ 	int limit;
+ 
+-	enet_dma_writel(priv, 0, ENETDMA_CHANCFG_REG(chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG_REG(chan));
+ 
+ 	limit = 1000;
+ 	do {
+ 		u32 val;
+ 
+-		val = enet_dma_readl(priv, ENETDMA_CHANCFG_REG(chan));
+-		if (!(val & ENETDMA_CHANCFG_EN_MASK))
++		val = enet_dmac_readl(priv, ENETDMAC_CHANCFG_REG(chan));
++		if (!(val & ENETDMAC_CHANCFG_EN_MASK))
+ 			break;
+ 		udelay(1);
+ 	} while (limit--);
+@@ -1059,8 +1081,8 @@ static int bcm_enet_stop(struct net_devi
+ 
+ 	/* mask all interrupts */
+ 	enet_writel(priv, 0, ENET_IRMASK_REG);
+-	enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
+-	enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
+ 
+ 	/* make sure no mib update is scheduled */
+ 	cancel_work_sync(&priv->mib_update_task);
+@@ -1598,7 +1620,7 @@ static int bcm_enet_probe(struct platfor
+ 
+ 	/* stop if shared driver failed, assume driver->probe will be
+ 	 * called in the same order we register devices (correct ?) */
+-	if (!bcm_enet_shared_base)
++	if (!bcm_enet_shared_base[0])
+ 		return -ENODEV;
+ 
+ 	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+@@ -1904,30 +1926,61 @@ struct platform_driver bcm63xx_enet_driv
+ static int bcm_enet_shared_probe(struct platform_device *pdev)
+ {
+ 	struct resource *res;
++	int ret, i, requested[3];
+ 
+-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+-	if (!res)
+-		return -ENODEV;
++	memset(bcm_enet_shared_base, 0, sizeof (bcm_enet_shared_base));
++	memset(requested, 0, sizeof (requested));
+ 
+-	if (!request_mem_region(res->start, resource_size(res),
+-				"bcm63xx_enet_dma"))
+-		return -EBUSY;
++	for (i = 0; i < 3; i++) {
++		void __iomem *p;
+ 
+-	bcm_enet_shared_base = ioremap(res->start, resource_size(res));
+-	if (!bcm_enet_shared_base) {
+-		release_mem_region(res->start, resource_size(res));
+-		return -ENOMEM;
++		res = platform_get_resource(pdev, IORESOURCE_MEM, i);
++		if (!res) {
++			ret = -EINVAL;
++			goto fail;
++		}
++
++		if (!request_mem_region(res->start, resource_size(res),
++					"bcm63xx_enet_dma")) {
++			ret = -EBUSY;
++			goto fail;
++		}
++		requested[i] = 0;
++
++		p = ioremap(res->start, resource_size(res));
++		if (!p) {
++			ret = -ENOMEM;
++			goto fail;
++		}
++
++		bcm_enet_shared_base[i] = p;
+ 	}
++
+ 	return 0;
++
++fail:
++	for (i = 0; i < 3; i++) {
++		res = platform_get_resource(pdev, IORESOURCE_MEM, i);
++		if (!res)
++			continue;
++		if (bcm_enet_shared_base[i])
++			iounmap(bcm_enet_shared_base[i]);
++		if (requested[i])
++			release_mem_region(res->start, resource_size(res));
++	}
++	return ret;
+ }
+ 
+ static int bcm_enet_shared_remove(struct platform_device *pdev)
+ {
+ 	struct resource *res;
++	int i;
+ 
+-	iounmap(bcm_enet_shared_base);
+-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+-	release_mem_region(res->start, resource_size(res));
++	for (i = 0; i < 3; i++) {
++		iounmap(bcm_enet_shared_base[i]);
++		res = platform_get_resource(pdev, IORESOURCE_MEM, i);
++		release_mem_region(res->start, resource_size(res));
++	}
+ 	return 0;
+ }
+ 

target/linux/brcm63xx/patches-3.8/416-bcm63xx_enet-reset-port-link-state-in-bcm_enetsw_ope.patch

@@ -0,0 +1,28 @@
+From 6d5c5bb13db3fd8e3dd0b82742b3957f41a4a3ac Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Thu, 24 May 2012 20:38:58 +0200
+Subject: [PATCH] bcm63xx_enet: reset port link state in bcm_enetsw_open
+
+bcm_enetsw_open disables all ports, but does not reset their link state.
+This results in connected ports staying disabled after a ifdown/ifup
+cycle, since bcm_enetsw_phy_poll only enables them if their current state
+is different from the stored link state.
+
+Fix this by also resetting the port link state.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c |    2 ++
+ 1 file changed, 2 insertions(+)
+
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -2213,6 +2213,8 @@ static int bcm_enetsw_open(struct net_de
+ 		enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK |
+ 			      ENETSW_PTCTRL_TXDIS_MASK,
+ 			      ENETSW_PTCTRL_REG(i));
++
++		priv->sw_port_link[i] = 0;
+ 	}
+ 
+ 	/* reset mib */

target/linux/brcm63xx/patches-3.8/417-bcm63xx_enet-don-t-overwrite-settings-when-setting-d.patch

@@ -0,0 +1,20 @@
+From e79bc74f76361020d820ed4611d28f70ebd845ca Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 10 Jul 2012 10:44:09 +0200
+Subject: [PATCH 34/84] bcm63xx_enet: don't overwrite settings when setting duplex on force
+
+---
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c |    2 +-
+ 1 files changed, 1 insertions(+), 1 deletions(-)
+
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -2333,7 +2333,7 @@ static int bcm_enetsw_open(struct net_de
+ 		}
+ 
+ 		if (port->force_duplex_full)
+-			override = ENETSW_IMPOV_FDX_MASK;
++			override |= ENETSW_IMPOV_FDX_MASK;
+ 
+ 
+ 		enetsw_writeb(priv, override, ENETSW_PORTOV_REG(i));

target/linux/brcm63xx/patches-3.8/418-bcm63xx_enet-store-the-number-of-ports-instead-of-ha.patch

@@ -0,0 +1,98 @@
+From efe31ec8fca92162fc21630611971345014a81a0 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 10 Jul 2012 10:39:30 +0200
+Subject: [PATCH 33/84] bcm63xx_enet: store the number of ports instead of hardcoding them
+
+This will be needed for devices with a different number of ports
+---
+ arch/mips/bcm63xx/dev-enet.c                       |    2 ++
+ .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h    |    2 ++
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c       |    9 +++++----
+ drivers/net/ethernet/broadcom/bcm63xx_enet.h       |    1 +
+ 4 files changed, 10 insertions(+), 4 deletions(-)
+
+--- a/arch/mips/bcm63xx/dev-enet.c
++++ b/arch/mips/bcm63xx/dev-enet.c
+@@ -239,6 +239,8 @@ bcm63xx_enetsw_register(const struct bcm
+ 
+ 	memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof (*pd));
+ 
++	enetsw_pd.num_ports = ENETSW_PORTS_6368;
++
+ 	ret = platform_device_register(&bcm63xx_enetsw_device);
+ 	if (ret)
+ 		return ret;
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
+@@ -43,6 +43,7 @@ struct bcm63xx_enet_platform_data {
+  * on board ethernet switch platform data
+  */
+ #define ENETSW_MAX_PORT	6
++#define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */
+ 
+ struct bcm63xx_enetsw_port {
+ 	int		used;
+@@ -58,6 +59,7 @@ struct bcm63xx_enetsw_port {
+ 
+ struct bcm63xx_enetsw_platform_data {
+ 	char mac_addr[ETH_ALEN];
++	int num_ports;
+ 	struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
+ };
+ 
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -2041,7 +2041,7 @@ static void swphy_poll_timer(unsigned lo
+ 	struct bcm_enet_priv *priv = (struct bcm_enet_priv *)data;
+ 	unsigned int i;
+ 
+-	for (i = 0; i < ARRAY_SIZE(priv->used_ports); i++) {
++	for (i = 0; i < priv->num_ports; i++) {
+ 		struct bcm63xx_enetsw_port *port;
+ 		int val, j, up, advertise, lpa, lpa2, speed, duplex, media;
+ 		u8 override;
+@@ -2207,7 +2207,7 @@ static int bcm_enetsw_open(struct net_de
+ 	priv->rx_curr_desc = 0;
+ 
+ 	/* disable all ports */
+-	for (i = 0; i < 6; i++) {
++	for (i = 0; i < priv->num_ports; i++) {
+ 		enetsw_writeb(priv, ENETSW_PORTOV_ENABLE_MASK,
+ 			      ENETSW_PORTOV_REG(i));
+ 		enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK |
+@@ -2303,7 +2303,7 @@ static int bcm_enetsw_open(struct net_de
+ 	/*
+ 	 * apply override config for bypass_link ports here.
+ 	 */
+-	for (i = 0; i < ARRAY_SIZE(priv->used_ports); i++) {
++	for (i = 0; i < priv->num_ports; i++) {
+ 		struct bcm63xx_enetsw_port *port;
+ 		u8 override;
+ 		port = &priv->used_ports[i];
+@@ -2447,7 +2447,7 @@ static int bcm_enetsw_phy_is_external(st
+ {
+ 	int i;
+ 
+-	for (i = 0; i < (int)ARRAY_SIZE(priv->used_ports); ++i) {
++	for (i = 0; i < priv->num_ports; ++i) {
+ 		if (!priv->used_ports[i].used)
+ 			continue;
+ 		if (priv->used_ports[i].phy_id == phy_id)
+@@ -2735,6 +2735,7 @@ static int bcm_enetsw_probe(struct platf
+ 		memcpy(dev->dev_addr, pd->mac_addr, ETH_ALEN);
+ 		memcpy(priv->used_ports, pd->used_ports,
+ 		       sizeof (pd->used_ports));
++		priv->num_ports = pd->num_ports;
+ 	}
+ 
+ 	ret = compute_hw_mtu(priv, dev->mtu);
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h
+@@ -326,6 +326,7 @@ struct bcm_enet_priv {
+ 	unsigned int hw_mtu;
+ 
+ 	/* port mapping for switch devices */
++	int num_ports;
+ 	struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
+ 	int sw_port_link[ENETSW_MAX_PORT];
+ 

target/linux/brcm63xx/patches-3.8/419-bcm63xx_enet-store-is_sw-in-a-variable-instead-of-ch.patch

@@ -0,0 +1,73 @@
+From ef581388c45dbc48f7bbe050e87deb1e3c63a698 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 10 Jul 2012 10:52:02 +0200
+Subject: [PATCH 35/84] bcm63xx_enet: store is_sw in a variable instead of checking the cpuid
+
+Reduces the number of changes needed for making enetsw work on new
+chips.
+---
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c |    7 +++++--
+ drivers/net/ethernet/broadcom/bcm63xx_enet.h |   10 ++--------
+ 2 files changed, 7 insertions(+), 10 deletions(-)
+
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -364,7 +364,7 @@ static int bcm_enet_receive_queue(struct
+ 		}
+ 
+ 		/* recycle packet if it's marked as bad */
+-		if (!bcm_enet_is_sw(priv) &&
++		if (!priv->enet_is_sw &&
+ 		    unlikely(len_stat & DMADESC_ERR_MASK)) {
+ 			dev->stats.rx_errors++;
+ 
+@@ -597,7 +597,7 @@ static int bcm_enet_start_xmit(struct sk
+ 	}
+ 
+ 	/* pad small packets sent on a switch device */
+-	if (bcm_enet_is_sw(priv) && skb->len < 64) {
++	if (priv->enet_is_sw && skb->len < 64) {
+ 		int needed = 64 - skb->len;
+ 		char *data;
+ 
+@@ -1700,6 +1700,8 @@ static int bcm_enet_probe(struct platfor
+ 		return -ENOMEM;
+ 	priv = netdev_priv(dev);
+ 
++	priv->enet_is_sw = false;
++
+ 	ret = compute_hw_mtu(priv, dev->mtu);
+ 	if (ret)
+ 		goto out;
+@@ -2725,6 +2727,7 @@ static int bcm_enetsw_probe(struct platf
+ 	memset(priv, 0, sizeof(*priv));
+ 
+ 	/* initialize default and fetch platform data */
++	priv->enet_is_sw = true;
+ 	priv->irq_rx = irq_rx;
+ 	priv->irq_tx = irq_tx;
+ 	priv->rx_ring_size = BCMENET_DEF_RX_DESC;
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h
+@@ -325,6 +325,8 @@ struct bcm_enet_priv {
+ 	/* maximum hardware transmit/receive size */
+ 	unsigned int hw_mtu;
+ 
++	bool enet_is_sw;
++
+ 	/* port mapping for switch devices */
+ 	int num_ports;
+ 	struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
+@@ -335,12 +337,4 @@ struct bcm_enet_priv {
+ 	spinlock_t enetsw_mdio_lock;
+ };
+ 
+-static inline int bcm_enet_is_sw(struct bcm_enet_priv *priv)
+-{
+-	if (BCMCPU_IS_6368())
+-		return 1;
+-	else
+-		return 0;
+-}
+-
+ #endif /* ! BCM63XX_ENET_H_ */

target/linux/brcm63xx/patches-3.8/420-BCM63XX-allow-enetsw-without-tx-irq.patch

@@ -0,0 +1,69 @@
+From 625894c377ba266c0044675b53f05d65db6355b6 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sun, 8 Jul 2012 13:07:52 +0200
+Subject: [PATCH 38/84] BCM63XX: allow enetsw without tx irq
+
+---
+ arch/mips/bcm63xx/dev-enet.c                 |    2 ++
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c |   18 +++++++++++-------
+ 2 files changed, 13 insertions(+), 7 deletions(-)
+
+--- a/arch/mips/bcm63xx/dev-enet.c
++++ b/arch/mips/bcm63xx/dev-enet.c
+@@ -236,6 +236,8 @@ bcm63xx_enetsw_register(const struct bcm
+ 	enetsw_res[0].end += RSET_ENETSW_SIZE - 1;
+ 	enetsw_res[1].start = bcm63xx_get_irq_number(IRQ_ENETSW_RXDMA0);
+ 	enetsw_res[2].start = bcm63xx_get_irq_number(IRQ_ENETSW_TXDMA0);
++	if (!enetsw_res[2].start)
++		enetsw_res[2].start = -1;
+ 
+ 	memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof (*pd));
+ 
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -2151,10 +2151,12 @@ static int bcm_enetsw_open(struct net_de
+ 	if (ret)
+ 		goto out_freeirq;
+ 
+-	ret = request_irq(priv->irq_tx, bcm_enet_isr_dma,
+-			  IRQF_DISABLED, dev->name, dev);
+-	if (ret)
+-		goto out_freeirq_rx;
++	if (priv->irq_tx != -1) {
++		ret = request_irq(priv->irq_tx, bcm_enet_isr_dma,
++				  IRQF_DISABLED, dev->name, dev);
++		if (ret)
++			goto out_freeirq_rx;
++	}
+ 
+ 	/* allocate rx dma ring */
+ 	size = priv->rx_ring_size * sizeof(struct bcm_enet_desc);
+@@ -2376,7 +2378,8 @@ out_free_rx_ring:
+ 			  priv->rx_desc_cpu, priv->rx_desc_dma);
+ 
+ out_freeirq_tx:
+-	free_irq(priv->irq_tx, dev);
++	if (priv->irq_tx != -1)
++		free_irq(priv->irq_tx, dev);
+ 
+ out_freeirq_rx:
+ 	free_irq(priv->irq_rx, dev);
+@@ -2433,7 +2436,8 @@ static int bcm_enetsw_stop(struct net_de
+ 			  priv->rx_desc_cpu, priv->rx_desc_dma);
+ 	dma_free_coherent(kdev, priv->tx_desc_alloc_size,
+ 			  priv->tx_desc_cpu, priv->tx_desc_dma);
+-	free_irq(priv->irq_tx, dev);
++	if (priv->irq_tx != -1)
++		free_irq(priv->irq_tx, dev);
+ 	free_irq(priv->irq_rx, dev);
+ 
+ 	return 0;
+@@ -2716,7 +2720,7 @@ static int bcm_enetsw_probe(struct platf
+ 	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ 	irq_rx = platform_get_irq(pdev, 0);
+ 	irq_tx = platform_get_irq(pdev, 1);
+-	if (!res_mem || irq_rx < 0 || irq_tx < 0)
++	if (!res_mem || irq_rx < 0)
+ 		return -ENODEV;
+ 
+ 	ret = 0;

target/linux/brcm63xx/patches-3.8/421-BCM63XX-use-port-id-for-deciding-external-phy.patch

@@ -0,0 +1,87 @@
+From 85e4551e033df7cb043e93042661fc1e58799efa Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sun, 8 Jul 2012 15:36:23 +0200
+Subject: [PATCH 52/84] BCM63XX: use port id for deciding external phy
+
+Ports 0-3 always use the internal phy, while 4+ always need an external
+phy to work.
+---
+ .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h    |    3 ++-
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c       |   15 ++++++++-------
+ drivers/net/ethernet/broadcom/bcm63xx_enet.h       |    5 +++++
+ 3 files changed, 15 insertions(+), 8 deletions(-)
+
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
+@@ -45,9 +45,10 @@ struct bcm63xx_enet_platform_data {
+ #define ENETSW_MAX_PORT	6
+ #define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */
+ 
++#define ENETSW_RGMII_PORT0	4
++
+ struct bcm63xx_enetsw_port {
+ 	int		used;
+-	int		external_phy;
+ 	int		phy_id;
+ 
+ 	int		bypass_link;
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -2046,6 +2046,7 @@ static void swphy_poll_timer(unsigned lo
+ 	for (i = 0; i < priv->num_ports; i++) {
+ 		struct bcm63xx_enetsw_port *port;
+ 		int val, j, up, advertise, lpa, lpa2, speed, duplex, media;
++		int external_phy = bcm_enet_port_is_rgmii(i);
+ 		u8 override;
+ 
+ 		port = &priv->used_ports[i];
+@@ -2057,7 +2058,7 @@ static void swphy_poll_timer(unsigned lo
+ 
+ 		/* dummy read to clear */
+ 		for (j = 0; j < 2; j++)
+-			val = bcmenet_sw_mdio_read(priv, port->external_phy,
++			val = bcmenet_sw_mdio_read(priv, external_phy,
+ 						   port->phy_id, MII_BMSR);
+ 
+ 		if (val == 0xffff)
+@@ -2081,14 +2082,14 @@ static void swphy_poll_timer(unsigned lo
+ 			continue;
+ 		}
+ 
+-		advertise = bcmenet_sw_mdio_read(priv, port->external_phy,
++		advertise = bcmenet_sw_mdio_read(priv, external_phy,
+ 						 port->phy_id, MII_ADVERTISE);
+ 
+-		lpa = bcmenet_sw_mdio_read(priv, port->external_phy,
+-					   port->phy_id, MII_LPA);
++		lpa = bcmenet_sw_mdio_read(priv, external_phy, port->phy_id,
++					   MII_LPA);
+ 
+-		lpa2 = bcmenet_sw_mdio_read(priv, port->external_phy,
+-					   port->phy_id, MII_STAT1000);
++		lpa2 = bcmenet_sw_mdio_read(priv, external_phy, port->phy_id,
++					    MII_STAT1000);
+ 
+ 		/* figure out media and duplex from advertise and LPA values */
+ 		media = mii_nway_result(lpa & advertise);
+@@ -2457,7 +2458,7 @@ static int bcm_enetsw_phy_is_external(st
+ 		if (!priv->used_ports[i].used)
+ 			continue;
+ 		if (priv->used_ports[i].phy_id == phy_id)
+-			return priv->used_ports[i].external_phy;
++			return bcm_enet_port_is_rgmii(i);
+ 	}
+ 
+ 	printk_once(KERN_WARNING  "bcm63xx_enet: could not find a used port "
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h
+@@ -337,4 +337,9 @@ struct bcm_enet_priv {
+ 	spinlock_t enetsw_mdio_lock;
+ };
+ 
++static inline int bcm_enet_port_is_rgmii(int portid)
++{
++	return portid >= ENETSW_RGMII_PORT0;
++}
++
+ #endif /* ! BCM63XX_ENET_H_ */

target/linux/brcm63xx/patches-3.8/422-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch

@@ -0,0 +1,53 @@
+From d8237d704fc25eb2fc25ef4403608b78c6a6d4be Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sun, 15 Jul 2012 20:08:57 +0200
+Subject: [PATCH 54/81] bcm63xx_enet: enable rgmii clock on external ports
+
+---
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h |   13 +++++++++++++
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c      |   12 ++++++++++++
+ 2 files changed, 25 insertions(+), 0 deletions(-)
+
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -861,6 +861,19 @@
+ #define ENETSW_PORTOV_FDX_MASK		(1 << 1)
+ #define ENETSW_PORTOV_LINKUP_MASK	(1 << 0)
+ 
++/* Port RGMII control register */
++#define ENETSW_RGMII_CTRL_REG(x)	(0x60 + (x))
++#define ENETSW_RGMII_CTRL_GMII_CLK_EN	(1 << 7)
++#define ENETSW_RGMII_CTRL_MII_OVERRIDE_EN (1 << 6)
++#define ENETSW_RGMII_CTRL_MII_MODE_MASK	(3 << 4)
++#define ENETSW_RGMII_CTRL_RGMII_MODE	(0 << 4)
++#define ENETSW_RGMII_CTRL_MII_MODE	(1 << 4)
++#define ENETSW_RGMII_CTRL_RVMII_MODE	(2 << 4)
++#define ENETSW_RGMII_CTRL_TIMING_SEL_EN	(1 << 0)
++
++/* Port RGMII timing register */
++#define ENETSW_RGMII_TIMING_REG(x)	(0x68 + (x))
++
+ /* MDIO control register */
+ #define ENETSW_MDIOC_REG		(0xb0)
+ #define ENETSW_MDIOC_EXT_MASK		(1 << 16)
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -2222,6 +2222,18 @@ static int bcm_enetsw_open(struct net_de
+ 		priv->sw_port_link[i] = 0;
+ 	}
+ 
++	/* enable external ports */
++	for (i = ENETSW_RGMII_PORT0; i < priv->num_ports; i++) {
++		u8 rgmii_ctrl;
++
++		if (!priv->used_ports[i].used)
++			continue;
++
++		rgmii_ctrl = enetsw_readb(priv, ENETSW_RGMII_CTRL_REG(i));
++		rgmii_ctrl |= ENETSW_RGMII_CTRL_GMII_CLK_EN;
++		enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i));
++	}
++
+ 	/* reset mib */
+ 	val = enetsw_readb(priv, ENETSW_GMCR_REG);
+ 	val |= ENETSW_GMCR_RST_MIB_MASK;

target/linux/brcm63xx/patches-3.8/423-bcm63xx_enet-fix-lockup-on-BCM6328.patch

@@ -0,0 +1,93 @@
+From 382a0b0dc4cbd0e0fbfd6c2d132e972c3d1245b0 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sun, 13 Nov 2011 14:59:37 +0100
+Subject: [PATCH 39/84] bcm63xx_enet: fix lockup on BCM6328
+
+BCM6328 locks up on a maxburst size of 16, reduce it to 8 for BCM6328 and
+BCM6368.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c |   13 +++++++------
+ drivers/net/ethernet/broadcom/bcm63xx_enet.h |    4 ++++
+ 2 files changed, 11 insertions(+), 6 deletions(-)
+
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -261,7 +261,6 @@ static int bcm_enet_refill_rx(struct net
+ 			if (!skb)
+ 				break;
+ 			priv->rx_skb[desc_idx] = skb;
+-
+ 			p = dma_map_single(&priv->pdev->dev, skb->data,
+ 					   priv->rx_skb_size,
+ 					   DMA_FROM_DEVICE);
+@@ -995,9 +994,9 @@ static int bcm_enet_open(struct net_devi
+ 	enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG);
+ 
+ 	/* set dma maximum burst len */
+-	enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
++	enet_dmac_writel(priv, priv->dma_maxburst,
+ 			 ENETDMAC_MAXBURST_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
++	enet_dmac_writel(priv, priv->dma_maxburst,
+ 			 ENETDMAC_MAXBURST_REG(priv->tx_chan));
+ 
+ 	/* set correct transmit fifo watermark */
+@@ -1593,7 +1592,7 @@ static int compute_hw_mtu(struct bcm_ene
+ 	 * it's appended
+ 	 */
+ 	priv->rx_skb_size = ALIGN(actual_mtu + ETH_FCS_LEN,
+-				  BCMENET_DMA_MAXBURST * 4);
++				  priv->dma_maxburst * 4);
+ 	return 0;
+ }
+ 
+@@ -1701,6 +1700,7 @@ static int bcm_enet_probe(struct platfor
+ 	priv = netdev_priv(dev);
+ 
+ 	priv->enet_is_sw = false;
++	priv->dma_maxburst = BCMENET_DMA_MAXBURST;
+ 
+ 	ret = compute_hw_mtu(priv, dev->mtu);
+ 	if (ret)
+@@ -2282,9 +2282,9 @@ static int bcm_enetsw_open(struct net_de
+ 	enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan));
+ 
+ 	/* set dma maximum burst len */
+-	enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
++	enet_dmac_writel(priv, priv->dma_maxburst,
+ 			 ENETDMAC_MAXBURST_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
++	enet_dmac_writel(priv, priv->dma_maxburst,
+ 			 ENETDMAC_MAXBURST_REG(priv->tx_chan));
+ 
+ 	/* set flow control low/high threshold to 1/3 / 2/3 */
+@@ -2749,6 +2749,7 @@ static int bcm_enetsw_probe(struct platf
+ 	priv->irq_tx = irq_tx;
+ 	priv->rx_ring_size = BCMENET_DEF_RX_DESC;
+ 	priv->tx_ring_size = BCMENET_DEF_TX_DESC;
++	priv->dma_maxburst = BCMENETSW_DMA_MAXBURST;
+ 
+ 	pd = pdev->dev.platform_data;
+ 	if (pd) {
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h
+@@ -18,6 +18,7 @@
+ 
+ /* maximum burst len for dma (4 bytes unit) */
+ #define BCMENET_DMA_MAXBURST	16
++#define BCMENETSW_DMA_MAXBURST	8
+ 
+ /* tx transmit threshold (4 bytes unit), fifo is 256 bytes, the value
+  * must be low enough so that a DMA transfer of above burst length can
+@@ -252,6 +253,9 @@ struct bcm_enet_priv {
+ 	/* number of dma desc in tx ring */
+ 	int tx_ring_size;
+ 
++	/* maximum dma burst size */
++	int dma_maxburst;
++
+ 	/* cpu view of rx dma ring */
+ 	struct bcm_enet_desc *tx_desc_cpu;
+ 

target/linux/brcm63xx/patches-3.8/424-MIPS-BCM63XX-add-support-for-BCM6328-in-bcm_enetsw.patch

@@ -0,0 +1,79 @@
+From a1bd0479a1ddac4f21afd4ebfe8f667b9fa5eff2 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 14 Jun 2011 21:14:39 +0200
+Subject: [PATCH 50/72] MIPS: BCM63XX: add support for BCM6328 in bcm_enetsw
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/clk.c                               |   15 +++++++++++----
+ arch/mips/bcm63xx/dev-enet.c                          |    9 ++++++---
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h |    1 +
+ 3 files changed, 18 insertions(+), 7 deletions(-)
+
+--- a/arch/mips/bcm63xx/clk.c
++++ b/arch/mips/bcm63xx/clk.c
+@@ -119,11 +119,18 @@ static struct clk clk_ephy = {
+  */
+ static void enetsw_set(struct clk *clk, int enable)
+ {
+-	if (!BCMCPU_IS_6368())
++	u32 mask;
++
++	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368())
+ 		return;
+-	bcm_hwclock_set(CKCTL_6368_ROBOSW_EN |
+-			CKCTL_6368_SWPKT_USB_EN |
+-			CKCTL_6368_SWPKT_SAR_EN, enable);
++
++	if (BCMCPU_IS_6328())
++		mask = CKCTL_6328_ROBOSW_EN;
++	else
++		mask = CKCTL_6368_ROBOSW_EN | CKCTL_6368_SWPKT_USB_EN |
++			CKCTL_6368_SWPKT_SAR_EN;
++
++	bcm_hwclock_set(mask, enable);
+ 	if (enable) {
+ 		/* reset switch core afer clock change */
+ 		bcm63xx_core_set_reset(BCM63XX_RESET_ENETSW, 1);
+--- a/arch/mips/bcm63xx/dev-enet.c
++++ b/arch/mips/bcm63xx/dev-enet.c
+@@ -141,7 +141,7 @@ static int __init register_shared(void)
+ 	shared_res[0].end = shared_res[0].start;
+ 	shared_res[0].end += (RSET_ENETDMA_SIZE)  - 1;
+ 
+-	if (BCMCPU_IS_6368())
++	if (BCMCPU_IS_6328() || BCMCPU_IS_6368())
+ 		chan_count = 32;
+ 	else
+ 		chan_count = 16;
+@@ -224,7 +224,7 @@ bcm63xx_enetsw_register(const struct bcm
+ {
+ 	int ret;
+ 
+-	if (!BCMCPU_IS_6368())
++	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368())
+ 		return -ENODEV;
+ 
+ 	ret = register_shared();
+@@ -241,7 +241,10 @@ bcm63xx_enetsw_register(const struct bcm
+ 
+ 	memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof (*pd));
+ 
+-	enetsw_pd.num_ports = ENETSW_PORTS_6368;
++	if (BCMCPU_IS_6328())
++		enetsw_pd.num_ports = ENETSW_PORTS_6328;
++	else if (BCMCPU_IS_6368())
++		enetsw_pd.num_ports = ENETSW_PORTS_6368;
+ 
+ 	ret = platform_device_register(&bcm63xx_enetsw_device);
+ 	if (ret)
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
+@@ -43,6 +43,7 @@ struct bcm63xx_enet_platform_data {
+  * on board ethernet switch platform data
+  */
+ #define ENETSW_MAX_PORT	6
++#define ENETSW_PORTS_6328 5 /* 4 FE PHY + 1 RGMII */
+ #define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */
+ 
+ #define ENETSW_RGMII_PORT0	4

target/linux/brcm63xx/patches-3.8/425-MIPS-BCM63XX-add-HS-SPI-platform-device-and-register.patch

@@ -0,0 +1,130 @@
+From 261ee140e75615351128eee497e6bbd76686784b Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sat, 12 Nov 2011 12:18:26 +0100
+Subject: [PATCH 51/72] MIPS: BCM63XX: add HS SPI platform device and register
+ it
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/Makefile                         |    4 +-
+ arch/mips/bcm63xx/boards/board_bcm963xx.c          |    2 +
+ arch/mips/bcm63xx/dev-hsspi.c                      |   57 ++++++++++++++++++++
+ .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h   |   20 +++++++
+ 4 files changed, 81 insertions(+), 2 deletions(-)
+ create mode 100644 arch/mips/bcm63xx/dev-hsspi.c
+ create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
+
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -1,7 +1,8 @@
+ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \
+ 		   setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
+-		   dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \
+-		   dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o usb-common.o
++		   dev-hsspi.o dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o \
++		   dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \
++		   usb-common.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -26,6 +26,7 @@
+ #include <bcm63xx_dev_enet.h>
+ #include <bcm63xx_dev_dsp.h>
+ #include <bcm63xx_dev_flash.h>
++#include <bcm63xx_dev_hsspi.h>
+ #include <bcm63xx_dev_pcmcia.h>
+ #include <bcm63xx_dev_spi.h>
+ #include <bcm63xx_dev_usb_ehci.h>
+@@ -955,6 +956,7 @@ int __init board_register_devices(void)
+ 			pr_err(PFX "failed to register fallback SPROM\n");
+ 	}
+ #endif
++	bcm63xx_hsspi_register();
+ 
+ 	bcm63xx_spi_register();
+ 
+--- /dev/null
++++ b/arch/mips/bcm63xx/dev-hsspi.c
+@@ -0,0 +1,57 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
++ */
++
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_dev_hsspi.h>
++#include <bcm63xx_regs.h>
++
++static struct resource spi_resources[] = {
++	{
++		.start		= -1, /* filled at runtime */
++		.end		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_MEM,
++	},
++	{
++		.start		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++static struct bcm63xx_hsspi_pdata spi_pdata = {
++	.bus_num	= 0,
++};
++
++static struct platform_device bcm63xx_hsspi_device = {
++	.name		= "bcm63xx-hsspi",
++	.id		= 0,
++	.num_resources	= ARRAY_SIZE(spi_resources),
++	.resource	= spi_resources,
++	.dev		= {
++		.platform_data = &spi_pdata,
++	},
++};
++
++int __init bcm63xx_hsspi_register(void)
++{
++
++	if (!BCMCPU_IS_6328())
++		return -ENODEV;
++
++	spi_resources[0].start = bcm63xx_regset_address(RSET_HSSPI);
++	spi_resources[0].end = spi_resources[0].start;
++	spi_resources[0].end += RSET_HSSPI_SIZE - 1;
++	spi_resources[1].start = bcm63xx_get_irq_number(IRQ_HSSPI);
++
++	spi_pdata.speed_hz = HSSPI_PLL_HZ_6328;
++
++	return platform_device_register(&bcm63xx_hsspi_device);
++}
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
+@@ -0,0 +1,20 @@
++#ifndef BCM63XX_DEV_HSSPI_H
++#define BCM63XX_DEV_HSSPI_H
++
++#include <linux/types.h>
++#include <bcm63xx_io.h>
++#include <bcm63xx_regs.h>
++
++int __init bcm63xx_hsspi_register(void);
++
++struct bcm63xx_hsspi_pdata {
++	int		bus_num;
++	u32		speed_hz;
++};
++
++#define bcm_hsspi_readl(o)	bcm_rset_readl(RSET_HSSPI, (o))
++#define bcm_hsspi_writel(v, o)	bcm_rset_writel(RSET_HSSPI, (v), (o))
++
++#define HSSPI_PLL_HZ_6328	133333333
++
++#endif /* BCM63XX_DEV_HSSPI_H */

target/linux/brcm63xx/patches-3.8/426-SPI-MIPS-BCM63XX-Add-HS-SPI-driver.patch

@@ -0,0 +1,481 @@
+From 4b27423676485d05bcd6fc6f3809164fb8f9d22d Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sat, 12 Nov 2011 12:19:55 +0100
+Subject: [PATCH 30/60] SPI: MIPS: BCM63XX: Add HSSPI driver
+
+Add a driver for the High Speed SPI controller found on newer BCM63XX SoCs.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h   |    2 +
+ drivers/spi/Kconfig                                |    7 +
+ drivers/spi/Makefile                               |    1 +
+ drivers/spi/spi-bcm63xx-hsspi.c                    |  427 ++++++++++++++++++++
+ 4 files changed, 437 insertions(+), 0 deletions(-)
+ create mode 100644 drivers/spi/spi-bcm63xx-hsspi.c
+
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
+@@ -17,4 +17,6 @@ struct bcm63xx_hsspi_pdata {
+ 
+ #define HSSPI_PLL_HZ_6328	133333333
+ 
++#define HSSPI_BUFFER_LEN   	512
++
+ #endif /* BCM63XX_DEV_HSSPI_H */
+--- a/drivers/spi/Kconfig
++++ b/drivers/spi/Kconfig
+@@ -100,6 +100,13 @@ config SPI_BCM63XX
+ 	help
+           Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
+ 
++config SPI_BCM63XX_HSSPI
++	tristate "Broadcom BCM63XX HS SPI controller driver"
++	depends on BCM63XX
++	help
++	  This enables support for the High Speed SPI controller present on
++	  newer Broadcom BCM63XX SoCs.
++
+ config SPI_BITBANG
+ 	tristate "Utilities for Bitbanging SPI masters"
+ 	help
+--- a/drivers/spi/Makefile
++++ b/drivers/spi/Makefile
+@@ -15,6 +15,7 @@ obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
+ obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
+ obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
+ obj-$(CONFIG_SPI_BCM63XX)		+= spi-bcm63xx.o
++obj-$(CONFIG_SPI_BCM63XX_HSSPI)		+= spi-bcm63xx-hsspi.o
+ obj-$(CONFIG_SPI_BFIN5XX)		+= spi-bfin5xx.o
+ obj-$(CONFIG_SPI_BFIN_SPORT)		+= spi-bfin-sport.o
+ obj-$(CONFIG_SPI_BITBANG)		+= spi-bitbang.o
+--- /dev/null
++++ b/drivers/spi/spi-bcm63xx-hsspi.c
+@@ -0,0 +1,427 @@
++/*
++ * Broadcom BCM63XX High Speed SPI Controller driver
++ *
++ * Copyright 2000-2010 Broadcom Corporation
++ * Copyright 2012 Jonas Gorski <jonas.gorski@gmail.com>
++ *
++ * Licensed under the GNU/GPL. See COPYING for details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/io.h>
++#include <linux/clk.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/delay.h>
++#include <linux/dma-mapping.h>
++#include <linux/err.h>
++#include <linux/interrupt.h>
++#include <linux/spi/spi.h>
++#include <linux/workqueue.h>
++
++#include <bcm63xx_regs.h>
++#include <bcm63xx_dev_hsspi.h>
++
++#define HSSPI_OP_CODE_SHIFT	13
++#define HSSPI_OP_SLEEP		(0 << HSSPI_OP_CODE_SHIFT)
++#define HSSPI_OP_READ_WRITE	(1 << HSSPI_OP_CODE_SHIFT)
++#define HSSPI_OP_WRITE		(2 << HSSPI_OP_CODE_SHIFT)
++#define HSSPI_OP_READ		(3 << HSSPI_OP_CODE_SHIFT)
++
++#define HSSPI_MAX_PREPEND_LEN	15
++
++#define HSSPI_MAX_SYNC_CLOCK	30000000
++
++struct bcm63xx_hsspi {
++	struct completion	done;
++	struct spi_transfer	*curr_trans;
++
++	struct platform_device  *pdev;
++	struct clk		*clk;
++	void __iomem		*regs;
++	u8 __iomem		*fifo;
++
++	u32			speed_hz;
++	int			irq;
++};
++
++static void bcm63xx_hsspi_set_clk(struct bcm63xx_hsspi *bs, int hz,
++				  int profile)
++{
++	u32 reg;
++
++	reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz));
++	bcm_hsspi_writel(CLK_CTRL_ACCUM_RST_ON_LOOP | reg,
++			 HSSPI_PROFILE_CLK_CTRL_REG(profile));
++
++	reg = bcm_hsspi_readl(HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
++	if (hz > HSSPI_MAX_SYNC_CLOCK)
++		reg |= SIGNAL_CTRL_ASYNC_INPUT_PATH;
++	else
++		reg &= ~SIGNAL_CTRL_ASYNC_INPUT_PATH;
++	bcm_hsspi_writel(reg, HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
++}
++
++static int bcm63xx_hsspi_do_txrx(struct spi_device *spi,
++				 struct spi_transfer *t1,
++				 struct spi_transfer *t2)
++{
++	struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master);
++	u8 chip_select = spi->chip_select;
++	u16 opcode = 0;
++	int len, prepend_size = 0;
++
++	init_completion(&bs->done);
++
++	bs->curr_trans = t2 ? t2 : t1;
++	bcm63xx_hsspi_set_clk(bs, bs->curr_trans->speed_hz, chip_select);
++
++	if (t2 && !t2->tx_buf)
++		prepend_size = t1->len;
++
++	bcm_hsspi_writel(prepend_size << MODE_CTRL_PREPENDBYTE_CNT_SHIFT |
++			 2 << MODE_CTRL_MULTIDATA_WR_STRT_SHIFT |
++			 2 << MODE_CTRL_MULTIDATA_RD_STRT_SHIFT | 0xff,
++			 HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
++
++	if (t1->rx_buf && t1->tx_buf)
++		opcode = HSSPI_OP_READ_WRITE;
++	else if (t1->rx_buf || (t2 && t2->rx_buf))
++		opcode = HSSPI_OP_READ;
++	else if (t1->tx_buf)
++		opcode = HSSPI_OP_WRITE;
++
++	if (opcode == HSSPI_OP_READ && t2)
++		len = t2->len;
++	else
++		len = t1->len;
++
++	if (t1->tx_buf) {
++		memcpy_toio(bs->fifo + 2, t1->tx_buf, t1->len);
++		if (t2 && t2->tx_buf) {
++			memcpy_toio(bs->fifo + 2 + t1->len,
++				    t2->tx_buf, t2->len);
++			len += t2->len;
++		}
++	}
++
++	opcode |= len;
++	memcpy_toio(bs->fifo, &opcode, sizeof(opcode));
++
++	/* enable interrupt */
++	bcm_hsspi_writel(HSSPI_PING0_CMD_DONE, HSSPI_INT_MASK_REG);
++
++	/* start the transfer */
++	bcm_hsspi_writel(chip_select << PINGPONG_CMD_SS_SHIFT |
++			 chip_select << PINGPONG_CMD_PROFILE_SHIFT |
++			 PINGPONG_COMMAND_START_NOW,
++			 HSSPI_PINGPONG_COMMAND_REG(0));
++
++	if (wait_for_completion_timeout(&bs->done, HZ) == 0) {
++		dev_err(&bs->pdev->dev, "transfer timed out!\n");
++		return -ETIMEDOUT;
++	}
++
++	return t1->len + (t2 ? t2->len : 0);
++}
++
++static int bcm63xx_hsspi_setup(struct spi_device *spi)
++{
++	u32 reg;
++
++	if (spi->bits_per_word != 8)
++		return -EINVAL;
++
++	if (spi->max_speed_hz == 0)
++		return -EINVAL;
++
++	reg = bcm_hsspi_readl(HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
++	reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING);
++	if (spi->mode & SPI_CPHA)
++		reg |= SIGNAL_CTRL_LAUNCH_RISING;
++	else
++		reg |= SIGNAL_CTRL_LATCH_RISING;
++	bcm_hsspi_writel(reg, HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
++
++	return 0;
++}
++
++static int bcm63xx_hsspi_transfer_one(struct spi_master *master,
++				      struct spi_message *msg)
++{
++	struct spi_transfer *t, *prev = NULL;
++	struct spi_device *spi = msg->spi;
++	u32 reg;
++	int ret = -EINVAL;
++	int len = 0;
++
++	/* check if we are able to make these transfers */
++	list_for_each_entry(t, &msg->transfers, transfer_list) {
++		if (!t->tx_buf && !t->rx_buf)
++			goto out;
++
++		if (t->speed_hz == 0)
++			t->speed_hz = spi->max_speed_hz;
++
++		if (t->speed_hz > spi->max_speed_hz)
++			goto out;
++
++		if (t->len > HSSPI_BUFFER_LEN)
++			goto out;
++
++		/*
++		 * This controller does not support keeping the chip select
++		 * active between transfers.
++		 * This logic currently supports combining:
++		 *  write then read with no cs_change (e.g. m25p80 RDSR)
++		 *  write then write with no cs_change (e.g. m25p80 PP)
++		 */
++		if (prev && prev->tx_buf && !prev->cs_change && !t->cs_change) {
++			/*
++			 * reject if we have to combine two tx transfers and
++			 * their combined length is bigger than the buffer
++			 */
++			if (prev->tx_buf && t->tx_buf &&
++			    (prev->len + t->len) > HSSPI_BUFFER_LEN)
++				goto out;
++			/*
++			 * reject if we need write more than 15 bytes in read
++			 * then write.
++			 */
++			if (prev->tx_buf && t->rx_buf &&
++			    prev->len > HSSPI_MAX_PREPEND_LEN)
++				goto out;
++		}
++
++	}
++
++	/* setup clock polarity */
++	reg = bcm_hsspi_readl(HSSPI_GLOBAL_CTRL_REG);
++	reg &= ~GLOBAL_CTRL_CLK_POLARITY;
++	if (spi->mode & SPI_CPOL)
++		reg |= GLOBAL_CTRL_CLK_POLARITY;
++	bcm_hsspi_writel(reg, HSSPI_GLOBAL_CTRL_REG);
++
++	list_for_each_entry(t, &msg->transfers, transfer_list) {
++		if (prev && prev->tx_buf && !prev->cs_change && !t->cs_change) {
++			/* combine write with following transfer */
++			ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, t);
++			if (ret < 0)
++				goto out;
++
++			len += ret;
++			prev = NULL;
++			continue;
++		}
++
++		/* write the previous pending transfer */
++		if (prev != NULL) {
++			ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, NULL);
++			if (ret < 0)
++				goto out;
++
++			len += ret;
++		}
++
++		prev = t;
++	}
++
++	/* do last pending transfer */
++	if (prev != NULL) {
++		ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, NULL);
++		if (ret < 0)
++			goto out;
++		len += ret;
++	}
++
++	msg->actual_length = len;
++	ret = 0;
++out:
++	msg->status = ret;
++	spi_finalize_current_message(master);
++	return 0;
++}
++
++static irqreturn_t bcm63xx_hsspi_interrupt(int irq, void *dev_id)
++{
++	struct spi_master *master = (struct spi_master *)dev_id;
++	struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
++
++	if (bcm_hsspi_readl(HSSPI_INT_STATUS_MASKED_REG) == 0)
++		return IRQ_NONE;
++
++	bcm_hsspi_writel(HSSPI_INT_CLEAR_ALL, HSSPI_INT_STATUS_REG);
++	bcm_hsspi_writel(0, HSSPI_INT_MASK_REG);
++
++	if (bs->curr_trans && bs->curr_trans->rx_buf)
++		memcpy_fromio(bs->curr_trans->rx_buf,  bs->fifo,
++			      bs->curr_trans->len);
++	complete(&bs->done);
++
++	return IRQ_HANDLED;
++}
++
++static int bcm63xx_hsspi_probe(struct platform_device *pdev)
++{
++
++	struct spi_master *master;
++	struct bcm63xx_hsspi *bs;
++	struct resource *res_mem;
++	void __iomem *regs;
++	struct device *dev = &pdev->dev;
++	struct bcm63xx_hsspi_pdata *pdata = pdev->dev.platform_data;
++	struct clk *clk;
++	int irq;
++	int ret;
++
++	irq = platform_get_irq(pdev, 0);
++	if (irq < 0) {
++		dev_err(dev, "no irq\n");
++		return -ENXIO;
++	}
++
++	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	regs = devm_request_and_ioremap(dev, res_mem);
++	if (!regs) {
++		dev_err(dev, "unable to ioremap regs\n");
++		return -ENXIO;
++	}
++
++	clk = clk_get(dev, "hsspi");
++
++	if (IS_ERR(clk)) {
++		ret = PTR_ERR(clk);
++		goto out_release;
++	}
++
++	clk_prepare_enable(clk);
++
++	master = spi_alloc_master(&pdev->dev, sizeof(*bs));
++	if (!master) {
++		ret = -ENOMEM;
++		goto out_disable_clk;
++	}
++
++	bs = spi_master_get_devdata(master);
++	bs->pdev = pdev;
++	bs->clk = clk;
++	bs->regs = regs;
++
++	master->bus_num = pdata->bus_num;
++	master->num_chipselect = 8;
++	master->setup = bcm63xx_hsspi_setup;
++	master->transfer_one_message = bcm63xx_hsspi_transfer_one;
++	master->mode_bits = SPI_CPOL | SPI_CPHA;
++
++	bs->speed_hz = pdata->speed_hz;
++	bs->fifo = (u8 __iomem *)(bs->regs + HSSPI_FIFO_REG(0));
++
++	platform_set_drvdata(pdev, master);
++
++	bs->curr_trans = NULL;
++
++	/* Initialize the hardware */
++	bcm_hsspi_writel(0, HSSPI_INT_MASK_REG);
++
++	/* clean up any pending interrupts */
++	bcm_hsspi_writel(HSSPI_INT_CLEAR_ALL, HSSPI_INT_STATUS_REG);
++
++	bcm_hsspi_writel(bcm_hsspi_readl(HSSPI_GLOBAL_CTRL_REG) |
++			 GLOBAL_CTRL_CLK_GATE_SSOFF,
++			 HSSPI_GLOBAL_CTRL_REG);
++
++	ret = devm_request_irq(dev, irq, bcm63xx_hsspi_interrupt, IRQF_SHARED,
++			       pdev->name, master);
++
++	if (ret)
++		goto out_put_master;
++
++	/* register and we are done */
++	ret = spi_register_master(master);
++	if (ret)
++		goto out_free_irq;
++
++	return 0;
++
++out_free_irq:
++	devm_free_irq(dev, bs->irq, master);
++out_put_master:
++	spi_master_put(master);
++out_disable_clk:
++	clk_disable_unprepare(clk);
++	clk_put(clk);
++out_release:
++	devm_ioremap_release(dev, regs);
++
++	return ret;
++}
++
++
++static int __exit bcm63xx_hsspi_remove(struct platform_device *pdev)
++{
++	struct spi_master *master = platform_get_drvdata(pdev);
++	struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
++
++	spi_unregister_master(master);
++
++	/* reset the hardware and block queue progress */
++	bcm_hsspi_writel(0, HSSPI_INT_MASK_REG);
++	clk_disable_unprepare(bs->clk);
++	clk_put(bs->clk);
++
++	return 0;
++}
++
++#ifdef CONFIG_PM
++static int bcm63xx_hsspi_suspend(struct platform_device *pdev,
++				 pm_message_t mesg)
++{
++	struct spi_master *master = platform_get_drvdata(pdev);
++	struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
++
++	spi_master_suspend(master);
++	clk_disable(bs->clk);
++
++	return 0;
++}
++
++static int bcm63xx_hsspi_resume(struct platform_device *pdev)
++{
++	struct spi_master *master = platform_get_drvdata(pdev);
++	struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
++
++	clk_enable(bs->clk);
++	spi_master_resume(master);
++
++	return 0;
++}
++
++static const struct dev_pm_ops bcm63xx_hsspi_pm_ops = {
++	.suspend	= bcm63xx_hsspi_suspend,
++	.resume		= bcm63xx_hsspi_resume,
++};
++
++#define BCM63XX_HSSPI_PM_OPS	(&bcm63xx_hsspi_pm_ops)
++#else
++#define BCM63XX_HSSPI_PM_OPS	NULL
++#endif
++
++
++
++static struct platform_driver bcm63xx_hsspi_driver = {
++	.driver = {
++		.name	= "bcm63xx-hsspi",
++		.owner	= THIS_MODULE,
++		.pm	= BCM63XX_HSSPI_PM_OPS,
++	},
++	.probe		= bcm63xx_hsspi_probe,
++	.remove		= __exit_p(bcm63xx_hsspi_remove),
++};
++
++module_platform_driver(bcm63xx_hsspi_driver);
++
++MODULE_ALIAS("platform:bcm63xx_hsspi");
++MODULE_DESCRIPTION("Broadcom BCM63xx HS SPI Controller driver");
++MODULE_AUTHOR("Jonas Gorski <jonas.gorski@gmail.com>");
++MODULE_LICENSE("GPL");

target/linux/brcm63xx/patches-3.8/427-MIPS-BCM63XX-Register-SPI-flash-if-present.patch

@@ -0,0 +1,102 @@
+From d135d94b3d1fe599d13e7198d5f502912d694c13 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sun, 3 Jul 2011 15:00:38 +0200
+Subject: [PATCH 29/60] MIPS: BCM63XX: Register SPI flash if present
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/dev-flash.c                     |   33 +++++++++++++++++++-
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h |    2 +
+ 2 files changed, 33 insertions(+), 2 deletions(-)
+
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -16,9 +16,12 @@
+ #include <linux/mtd/mtd.h>
+ #include <linux/mtd/partitions.h>
+ #include <linux/mtd/physmap.h>
++#include <linux/spi/spi.h>
++#include <linux/spi/flash.h>
+ 
+ #include <bcm63xx_cpu.h>
+ #include <bcm63xx_dev_flash.h>
++#include <bcm63xx_dev_hsspi.h>
+ #include <bcm63xx_regs.h>
+ #include <bcm63xx_io.h>
+ 
+@@ -55,6 +58,21 @@ static struct platform_device mtd_dev =
+ 	},
+ };
+ 
++static struct flash_platform_data bcm63xx_flash_data = {
++	.part_probe_types	= bcm63xx_part_types,
++};
++
++static struct spi_board_info bcm63xx_spi_flash_info[] = {
++	{
++		.bus_num	= 0,
++		.chip_select	= 0,
++		.mode		= 0,
++		.max_speed_hz	= 781000,
++		.modalias	= "m25p80",
++		.platform_data	= &bcm63xx_flash_data,
++	},
++};
++
+ static int __init bcm63xx_detect_flash_type(void)
+ {
+ 	u32 val;
+@@ -62,6 +80,11 @@ static int __init bcm63xx_detect_flash_t
+ 	switch (bcm63xx_get_cpu_id()) {
+ 	case BCM6328_CPU_ID:
+ 		val = bcm_misc_readl(MISC_STRAPBUS_6328_REG);
++		if (val & STRAPBUS_6328_HSSPI_CLK_FAST)
++			bcm63xx_spi_flash_info[0].max_speed_hz = 33333334;
++		else
++			bcm63xx_spi_flash_info[0].max_speed_hz = 16666667;
++
+ 		if (val & STRAPBUS_6328_BOOT_SEL_SERIAL)
+ 			return BCM63XX_FLASH_TYPE_SERIAL;
+ 		else
+@@ -79,6 +102,9 @@ static int __init bcm63xx_detect_flash_t
+ 			return BCM63XX_FLASH_TYPE_SERIAL;
+ 	case BCM6368_CPU_ID:
+ 		val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
++		if (val & STRAPBUS_6368_SPI_CLK_FAST)
++			bcm63xx_spi_flash_info[0].max_speed_hz = 20000000;
++
+ 		switch (val & STRAPBUS_6368_BOOT_SEL_MASK) {
+ 		case STRAPBUS_6368_BOOT_SEL_NAND:
+ 			return BCM63XX_FLASH_TYPE_NAND;
+@@ -110,8 +136,11 @@ int __init bcm63xx_flash_register(void)
+ 
+ 		return platform_device_register(&mtd_dev);
+ 	case BCM63XX_FLASH_TYPE_SERIAL:
+-		pr_warn("unsupported serial flash detected\n");
+-		return -ENODEV;
++		if (BCMCPU_IS_6328())
++			bcm63xx_flash_data.max_transfer_len = HSSPI_BUFFER_LEN;
++
++		return spi_register_board_info(bcm63xx_spi_flash_info,
++					ARRAY_SIZE(bcm63xx_spi_flash_info));
+ 	case BCM63XX_FLASH_TYPE_NAND:
+ 		pr_warn("unsupported NAND flash detected\n");
+ 		return -ENODEV;
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -629,6 +629,7 @@
+ #define GPIO_STRAPBUS_REG		0x40
+ #define STRAPBUS_6358_BOOT_SEL_PARALLEL	(1 << 1)
+ #define STRAPBUS_6358_BOOT_SEL_SERIAL	(0 << 1)
++#define STRAPBUS_6368_SPI_CLK_FAST	(1 << 6)
+ #define STRAPBUS_6368_BOOT_SEL_MASK	0x3
+ #define STRAPBUS_6368_BOOT_SEL_NAND	0
+ #define STRAPBUS_6368_BOOT_SEL_SERIAL	1
+@@ -1478,6 +1479,7 @@
+ #define STRAPBUS_6362_BOOT_SEL_NAND	(0 << 15)
+ 
+ #define MISC_STRAPBUS_6328_REG		0x240
++#define STRAPBUS_6328_HSSPI_CLK_FAST	(1 << 4)
+ #define STRAPBUS_6328_FCVO_SHIFT	7
+ #define STRAPBUS_6328_FCVO_MASK		(0x1f << STRAPBUS_6328_FCVO_SHIFT)
+ #define STRAPBUS_6328_BOOT_SEL_SERIAL	(1 << 28)

target/linux/brcm63xx/patches-3.8/428-MIPS-BCM63XX-add-flash-detection-for-BCM6362.patch

@@ -0,0 +1,50 @@
+From d9666553a10ea85ea64e3e8784a42167a1709ed5 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Mon, 21 Nov 2011 00:48:52 +0100
+Subject: [PATCH 55/84] MIPS: BCM63XX: add flash detection for BCM6362
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/dev-flash.c                     |   13 ++++++++++++-
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h |    1 +
+ 2 files changed, 13 insertions(+), 1 deletions(-)
+
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -100,6 +100,17 @@ static int __init bcm63xx_detect_flash_t
+ 			return BCM63XX_FLASH_TYPE_PARALLEL;
+ 		else
+ 			return BCM63XX_FLASH_TYPE_SERIAL;
++	case BCM6362_CPU_ID:
++		val = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
++		if (val & STRAPBUS_6362_HSSPI_CLK_FAST)
++			bcm63xx_spi_flash_info[0].max_speed_hz = 50000000;
++		else
++			bcm63xx_spi_flash_info[0].max_speed_hz = 20000000;
++
++		if (val & STRAPBUS_6362_BOOT_SEL_SERIAL)
++			return BCM63XX_FLASH_TYPE_SERIAL;
++		else
++			return BCM63XX_FLASH_TYPE_NAND;
+ 	case BCM6368_CPU_ID:
+ 		val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
+ 		if (val & STRAPBUS_6368_SPI_CLK_FAST)
+@@ -136,7 +147,7 @@ int __init bcm63xx_flash_register(void)
+ 
+ 		return platform_device_register(&mtd_dev);
+ 	case BCM63XX_FLASH_TYPE_SERIAL:
+-		if (BCMCPU_IS_6328())
++		if (BCMCPU_IS_6328() || BCMCPU_IS_6362())
+ 			bcm63xx_flash_data.max_transfer_len = HSSPI_BUFFER_LEN;
+ 
+ 		return spi_register_board_info(bcm63xx_spi_flash_info,
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -1474,6 +1474,7 @@
+ 
+ #define MISC_STRAPBUS_6362_REG		0x14
+ #define STRAPBUS_6362_FCVO_SHIFT	1
++#define STRAPBUS_6362_HSSPI_CLK_FAST	(1 << 13)
+ #define STRAPBUS_6362_FCVO_MASK		(0x1f << STRAPBUS_6362_FCVO_SHIFT)
+ #define STRAPBUS_6362_BOOT_SEL_SERIAL	(1 << 15)
+ #define STRAPBUS_6362_BOOT_SEL_NAND	(0 << 15)

target/linux/brcm63xx/patches-3.8/429-MIPS-BCM63XX-export-PSI-size-from-nvram.patch

@@ -0,0 +1,44 @@
+From ffbeb183bf0e9e12fd607c5352f48420c32f588f Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sat, 12 May 2012 23:04:17 +0200
+Subject: [PATCH 61/79] MIPS: BCM63XX: export PSI size from nvram
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/nvram.c                          |   11 +++++++++++
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h |    2 ++
+ 2 files changed, 13 insertions(+)
+
+--- a/arch/mips/bcm63xx/nvram.c
++++ b/arch/mips/bcm63xx/nvram.c
+@@ -35,6 +35,8 @@ struct bcm963xx_nvram {
+ 	u32	checksum_high;
+ };
+ 
++#define BCM63XX_DEFAULT_PSI_SIZE	64
++
+ static struct bcm963xx_nvram nvram;
+ static int mac_addr_used;
+ 
+@@ -105,3 +107,12 @@ int bcm63xx_nvram_get_mac_address(u8 *ma
+ 	return 0;
+ }
+ EXPORT_SYMBOL(bcm63xx_nvram_get_mac_address);
++
++int bcm63xx_nvram_get_psi_size(void)
++{
++	if (nvram.psi_size > 0)
++		return nvram.psi_size;
++
++	return BCM63XX_DEFAULT_PSI_SIZE;
++}
++EXPORT_SYMBOL(bcm63xx_nvram_get_psi_size);
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h
+@@ -32,4 +32,6 @@ u8 *bcm63xx_nvram_get_name(void);
+  */
+ int bcm63xx_nvram_get_mac_address(u8 *mac);
+ 
++int bcm63xx_nvram_get_psi_size(void);
++
+ #endif /* BCM63XX_NVRAM_H */

target/linux/brcm63xx/patches-3.8/430-MTD-bcm63xxpart-use-nvram-for-PSI-size.patch

@@ -0,0 +1,29 @@
+From 658afad639a9456e1bb6fe5bba0032f3c0c3f699 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 1 May 2012 14:10:39 +0200
+Subject: [PATCH 62/79] MTD: bcm63xxpart: use nvram for PSI size
+
+---
+ drivers/mtd/bcm63xxpart.c |    4 +++-
+ 1 file changed, 3 insertions(+), 1 deletion(-)
+
+--- a/drivers/mtd/bcm63xxpart.c
++++ b/drivers/mtd/bcm63xxpart.c
+@@ -32,6 +32,7 @@
+ #include <linux/mtd/mtd.h>
+ #include <linux/mtd/partitions.h>
+ 
++#include <asm/mach-bcm63xx/bcm63xx_nvram.h>
+ #include <linux/bcm963xx_tag.h>
+ #include <asm/mach-bcm63xx/board_bcm963xx.h>
+ 
+@@ -90,7 +91,8 @@ static int bcm63xx_parse_cfe_partitions(
+ 			      BCM63XX_CFE_BLOCK_SIZE);
+ 
+ 	cfelen = cfe_erasesize;
+-	nvramlen = cfe_erasesize;
++	nvramlen = bcm63xx_nvram_get_psi_size() * 1024;
++	nvramlen = roundup(nvramlen, cfe_erasesize);
+ 
+ 	/* Allocate memory for buffer */
+ 	buf = vmalloc(sizeof(struct bcm_tag));

target/linux/brcm63xx/patches-3.8/431-MTD-physmap-allow-passing-pp_data.patch

@@ -0,0 +1,41 @@
+From 266c506f4b262bd6aba0776a03d82c98e65d9906 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 1 May 2012 17:32:36 +0200
+Subject: [PATCH 63/79] MTD: physmap: allow passing pp_data
+
+---
+ drivers/mtd/maps/physmap.c  |    4 +++-
+ include/linux/mtd/physmap.h |    1 +
+ 2 files changed, 4 insertions(+), 1 deletion(-)
+
+--- a/drivers/mtd/maps/physmap.c
++++ b/drivers/mtd/maps/physmap.c
+@@ -100,6 +100,7 @@ static int physmap_flash_probe(struct pl
+ {
+ 	struct physmap_flash_data *physmap_data;
+ 	struct physmap_flash_info *info;
++	struct mtd_part_parser_data *pp_data;
+ 	const char **probe_type;
+ 	const char **part_types;
+ 	int err = 0;
+@@ -191,8 +192,9 @@ static int physmap_flash_probe(struct pl
+ 	spin_lock_init(&info->vpp_lock);
+ 
+ 	part_types = physmap_data->part_probe_types ? : part_probe_types;
++	pp_data = physmap_data->pp_data ? physmap_data->pp_data : NULL;
+ 
+-	mtd_device_parse_register(info->cmtd, part_types, NULL,
++	mtd_device_parse_register(info->cmtd, part_types, pp_data,
+ 				  physmap_data->parts, physmap_data->nr_parts);
+ 	return 0;
+ 
+--- a/include/linux/mtd/physmap.h
++++ b/include/linux/mtd/physmap.h
+@@ -32,6 +32,7 @@ struct physmap_flash_data {
+ 	char                    *probe_type;
+ 	struct mtd_partition	*parts;
+ 	const char		**part_probe_types;
++	struct mtd_part_parser_data *pp_data;
+ };
+ 
+ #endif /* __LINUX_MTD_PHYSMAP__ */

target/linux/brcm63xx/patches-3.8/432-BCM63XX-allow-providing-fixup-data-in-board-data.patch

@@ -0,0 +1,81 @@
+From 8879e209111192c5e9752d7bd203cf7582693328 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Thu, 3 May 2012 14:40:03 +0200
+Subject: [PATCH 58/72] BCM63XX: allow providing fixup data in board data
+
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c           |    9 ++++++++-
+ arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h |   10 ++++++++++
+ 2 files changed, 18 insertions(+), 1 deletion(-)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -33,6 +33,7 @@
+ #include <bcm63xx_dev_usb_ohci.h>
+ #include <bcm63xx_dev_usb_usbd.h>
+ #include <board_bcm963xx.h>
++#include <pci_ath9k_fixup.h>
+ 
+ #include <uapi/linux/bcm963xx_tag.h>
+ 
+@@ -910,6 +911,7 @@ int __init board_register_devices(void)
+ {
+ 	int button_count = 0;
+ 	int led_count = 0;
++	int i;
+ 
+ 	if (board.has_uart0)
+ 		bcm63xx_uart_register(0);
+@@ -948,7 +950,8 @@ int __init board_register_devices(void)
+ 	 * do this after registering enet devices
+ 	 */
+ #ifdef CONFIG_SSB_PCIHOST
+-	if (!bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) {
++	if (!board.has_caldata &&
++	    !bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) {
+ 		memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN);
+ 		memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN);
+ 		if (ssb_arch_register_fallback_sprom(
+@@ -990,5 +993,9 @@ int __init board_register_devices(void)
+ 		platform_device_register(&bcm63xx_gpio_keys_device);
+ 	}
+ 
++	/* register any fixups */
++	for (i = 0; i < board.has_caldata; i++)
++		pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset);
++
+ 	return 0;
+ }
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -8,6 +8,7 @@
+ #include <bcm63xx_dev_enet.h>
+ #include <bcm63xx_dev_usb_usbd.h>
+ #include <bcm63xx_dev_dsp.h>
++#include <pci_ath9k_fixup.h>
+ 
+ /*
+  * flash mapping
+@@ -15,6 +16,11 @@
+ #define BCM963XX_CFE_VERSION_OFFSET	0x570
+ #define BCM963XX_NVRAM_OFFSET		0x580
+ 
++struct ath9k_caldata {
++	unsigned int	slot;
++	u32		caldata_offset;
++};
++
+ /*
+  * board definition
+  */
+@@ -34,6 +40,10 @@ struct board_info {
+ 	unsigned int	has_dsp:1;
+ 	unsigned int	has_uart0:1;
+ 	unsigned int	has_uart1:1;
++	unsigned int	has_caldata:2;
++
++	/* wifi calibration data config */
++	struct ath9k_caldata caldata[2];
+ 
+ 	/* ethernet config */
+ 	struct bcm63xx_enet_platform_data enet0;

target/linux/brcm63xx/patches-3.8/433-MTD-m25p80-allow-passing-pp_data.patch

@@ -0,0 +1,40 @@
+From 7f17dfe9009beb07a3de0e380932a725293829df Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 1 May 2012 17:33:03 +0200
+Subject: [PATCH 64/79] MTD: m25p80: allow passing pp_data
+
+---
+ drivers/mtd/devices/m25p80.c |    3 +++
+ include/linux/spi/flash.h    |    2 ++
+ 2 files changed, 5 insertions(+)
+
+--- a/drivers/mtd/devices/m25p80.c
++++ b/drivers/mtd/devices/m25p80.c
+@@ -877,6 +877,9 @@ static int m25p_probe(struct spi_device
+ 			dev_warn(&spi->dev, "unrecognized id %s\n", data->type);
+ 	}
+ 
++	if (data && data->pp_data)
++		memcpy(&ppdata, data->pp_data, sizeof(ppdata));
++
+ 	info = (void *)id->driver_data;
+ 
+ 	if (info->jedec_id) {
+--- a/include/linux/spi/flash.h
++++ b/include/linux/spi/flash.h
+@@ -12,6 +12,7 @@ struct mtd_part_parser_data;
+  *	with chips that can't be queried for JEDEC or other IDs
+  * @part_probe_types: optional list of MTD parser names to use for
+  *	partitioning
++ * @pp_data: optional partition parser data.
+  *
+  * @max_transfer_len: option maximum read/write length limitation for
+  *	SPI controllers not able to transfer any length commands.
+@@ -30,6 +31,7 @@ struct flash_platform_data {
+ 	char		*type;
+ 
+ 	const char	**part_probe_types;
++	struct mtd_part_parser_data *pp_data;
+ 
+ 	unsigned int	max_transfer_len;
+ 	/* we'll likely add more ... use JEDEC IDs, etc */

target/linux/brcm63xx/patches-3.8/434-MIPS-BCM63XX-store-the-flash-type-in-global-variable.patch

@@ -0,0 +1,122 @@
+From f888824d352df894ab721a5ca067b0313500efe7 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Thu, 3 May 2012 12:17:54 +0200
+Subject: [PATCH 38/59] MIPS: BCM63XX: store the flash type in global variable
+
+---
+ arch/mips/bcm63xx/dev-flash.c                      |   36 +++++++++++++------
+ .../include/asm/mach-bcm63xx/bcm63xx_dev_flash.h   |    2 +
+ 2 files changed, 26 insertions(+), 12 deletions(-)
+
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -25,6 +25,8 @@
+ #include <bcm63xx_regs.h>
+ #include <bcm63xx_io.h>
+ 
++int bcm63xx_attached_flash = -1;
++
+ static struct mtd_partition mtd_partitions[] = {
+ 	{
+ 		.name		= "cfe",
+@@ -86,20 +88,23 @@ static int __init bcm63xx_detect_flash_t
+ 			bcm63xx_spi_flash_info[0].max_speed_hz = 16666667;
+ 
+ 		if (val & STRAPBUS_6328_BOOT_SEL_SERIAL)
+-			return BCM63XX_FLASH_TYPE_SERIAL;
++			bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL;
+ 		else
+-			return BCM63XX_FLASH_TYPE_NAND;
++			bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND;
++		break;
+ 	case BCM6338_CPU_ID:
+ 	case BCM6345_CPU_ID:
+ 	case BCM6348_CPU_ID:
+ 		/* no way to auto detect so assume parallel */
+-		return BCM63XX_FLASH_TYPE_PARALLEL;
++		bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL;
++		break;
+ 	case BCM6358_CPU_ID:
+ 		val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
+ 		if (val & STRAPBUS_6358_BOOT_SEL_PARALLEL)
+-			return BCM63XX_FLASH_TYPE_PARALLEL;
++			bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL;
+ 		else
+-			return BCM63XX_FLASH_TYPE_SERIAL;
++			bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL;
++		break;
+ 	case BCM6362_CPU_ID:
+ 		val = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
+ 		if (val & STRAPBUS_6362_HSSPI_CLK_FAST)
+@@ -108,9 +113,10 @@ static int __init bcm63xx_detect_flash_t
+ 			bcm63xx_spi_flash_info[0].max_speed_hz = 20000000;
+ 
+ 		if (val & STRAPBUS_6362_BOOT_SEL_SERIAL)
+-			return BCM63XX_FLASH_TYPE_SERIAL;
++			bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL;
+ 		else
+-			return BCM63XX_FLASH_TYPE_NAND;
++			bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND;
++		break;
+ 	case BCM6368_CPU_ID:
+ 		val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
+ 		if (val & STRAPBUS_6368_SPI_CLK_FAST)
+@@ -118,25 +124,32 @@ static int __init bcm63xx_detect_flash_t
+ 
+ 		switch (val & STRAPBUS_6368_BOOT_SEL_MASK) {
+ 		case STRAPBUS_6368_BOOT_SEL_NAND:
+-			return BCM63XX_FLASH_TYPE_NAND;
++			bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND;
++			break;
+ 		case STRAPBUS_6368_BOOT_SEL_SERIAL:
+-			return BCM63XX_FLASH_TYPE_SERIAL;
++			bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL;
++			break;
+ 		case STRAPBUS_6368_BOOT_SEL_PARALLEL:
+-			return BCM63XX_FLASH_TYPE_PARALLEL;
++			bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL;
++			break;
++		default:
++			return -EINVAL;
+ 		}
+ 	default:
+ 		return -EINVAL;
+ 	}
++
++	return 0;
+ }
+ 
+ int __init bcm63xx_flash_register(void)
+ {
+-	int flash_type;
+ 	u32 val;
+ 
+-	flash_type = bcm63xx_detect_flash_type();
+ 
+-	switch (flash_type) {
++	bcm63xx_detect_flash_type();
++
++	switch (bcm63xx_attached_flash) {
+ 	case BCM63XX_FLASH_TYPE_PARALLEL:
+ 		/* read base address of boot chip select (0) */
+ 		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+@@ -157,7 +170,7 @@ int __init bcm63xx_flash_register(void)
+ 		return -ENODEV;
+ 	default:
+ 		pr_err("flash detection failed for BCM%x: %d\n",
+-		       bcm63xx_get_cpu_id(), flash_type);
++		       bcm63xx_get_cpu_id(), bcm63xx_attached_flash);
+ 		return -ENODEV;
+ 	}
+ }
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
+@@ -7,6 +7,8 @@ enum {
+ 	BCM63XX_FLASH_TYPE_NAND,
+ };
+ 
++extern int bcm63xx_attached_flash;
++
+ int __init bcm63xx_flash_register(void);
+ 
+ #endif /* __BCM63XX_FLASH_H */

target/linux/brcm63xx/patches-3.8/435-BCM63XX-add-a-fixup-for-ath9k-devices.patch

@@ -0,0 +1,227 @@
+From bbebbf735a02b6d044ed928978ab4bd5f1833364 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Thu, 3 May 2012 14:36:11 +0200
+Subject: [PATCH 61/72] BCM63XX: add a fixup for ath9k devices
+
+---
+ arch/mips/bcm63xx/Makefile                         |    3 +-
+ arch/mips/bcm63xx/pci-ath9k-fixup.c                |  190 ++++++++++++++++++++
+ .../include/asm/mach-bcm63xx/pci_ath9k_fixup.h     |    7 +
+ 3 files changed, 199 insertions(+), 1 deletion(-)
+ create mode 100644 arch/mips/bcm63xx/pci-ath9k-fixup.c
+ create mode 100644 arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
+
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -2,7 +2,7 @@ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o
+ 		   setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
+ 		   dev-hsspi.o dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o \
+ 		   dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \
+-		   usb-common.o
++		   pci-ath9k-fixup.o usb-common.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- /dev/null
++++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c
+@@ -0,0 +1,190 @@
++/*
++ *  Broadcom BCM63XX Ath9k EEPROM fixup helper.
++ *
++ *  Copytight (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
++ *
++ *  Based on
++ *
++ *  Atheros AP94 reference board PCI initialization
++ *
++ *  Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
++ *
++ *  This program is free software; you can redistribute it and/or modify it
++ *  under the terms of the GNU General Public License version 2 as published
++ *  by the Free Software Foundation.
++ */
++
++#include <linux/pci.h>
++#include <linux/delay.h>
++#include <linux/ath9k_platform.h>
++
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_io.h>
++#include <bcm63xx_nvram.h>
++#include <bcm63xx_dev_pci.h>
++#include <bcm63xx_dev_flash.h>
++#include <bcm63xx_dev_hsspi.h>
++#include <pci_ath9k_fixup.h>
++
++struct ath9k_fixup {
++	unsigned slot;
++	u8 mac[ETH_ALEN];
++	struct ath9k_platform_data pdata;
++};
++
++static int ath9k_num_fixups;
++static struct ath9k_fixup ath9k_fixups[2] = {
++	{
++		.slot = 255,
++		.pdata = {
++			.led_pin	= -1,
++		},
++	},
++	{
++		.slot = 255,
++		.pdata = {
++			.led_pin	= -1,
++		},
++	},
++};
++
++static u16 *bcm63xx_read_eeprom(u16 *eeprom, u32 offset)
++{
++	u32 addr;
++
++	if (BCMCPU_IS_6328()) {
++		addr = 0x18000000;
++	} else {
++		addr = bcm_mpi_readl(MPI_CSBASE_REG(0));
++		addr &= MPI_CSBASE_BASE_MASK;
++	}
++
++	switch (bcm63xx_attached_flash) {
++	case BCM63XX_FLASH_TYPE_PARALLEL:
++		memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16));
++		return eeprom;
++	case BCM63XX_FLASH_TYPE_SERIAL:
++		/* the first megabyte is memory mapped */
++		if (offset < 0x100000) {
++			memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16));
++			return eeprom;
++		}
++
++		if (BCMCPU_IS_6328()) {
++			/* we can change the memory mapped megabyte */
++			bcm_hsspi_writel(offset & 0xf00000, 0x18);
++			memcpy(eeprom, (void *)KSEG1ADDR(addr + (offset & 0xfffff)), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16));
++			bcm_hsspi_writel(0, 0x18);
++			return eeprom;
++		}
++		/* can't do anything here without talking to the SPI controller. */
++	case BCM63XX_FLASH_TYPE_NAND:
++	default:
++		return NULL;
++	}
++}
++
++static void ath9k_pci_fixup(struct pci_dev *dev)
++{
++	void __iomem *mem;
++	struct ath9k_platform_data *pdata = NULL;
++	u16 *cal_data = NULL;
++	u16 cmd;
++	u32 bar0;
++	u32 val;
++	unsigned i;
++
++	for (i = 0; i < ath9k_num_fixups; i++) {
++		if (ath9k_fixups[i].slot != PCI_SLOT(dev->devfn))
++			continue;
++
++		cal_data = ath9k_fixups[i].pdata.eeprom_data;
++		pdata = &ath9k_fixups[i].pdata;
++		break;
++	}
++
++	if (cal_data == NULL)
++		return;
++
++	if (*cal_data != 0xa55a) {
++		pr_err("pci %s: invalid calibration data\n", pci_name(dev));
++		return;
++	}
++
++	pr_info("pci %s: fixup device configuration\n", pci_name(dev));
++
++	switch (bcm63xx_get_cpu_id()) {
++	case BCM6328_CPU_ID:
++		val = BCM_PCIE_MEM_BASE_PA;
++		break;
++	case BCM6348_CPU_ID:
++	case BCM6358_CPU_ID:
++	case BCM6368_CPU_ID:
++		val = BCM_PCI_MEM_BASE_PA;
++		break;
++	default:
++		BUG();
++	}
++
++	mem = ioremap(val, 0x10000);
++	if (!mem) {
++		pr_err("pci %s: ioremap error\n", pci_name(dev));
++		return;
++	}
++
++	pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0);
++	pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0);
++	pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, val);
++
++	pci_read_config_word(dev, PCI_COMMAND, &cmd);
++	cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
++	pci_write_config_word(dev, PCI_COMMAND, cmd);
++
++	/* set offset to first reg address */
++	cal_data += 3;
++	while(*cal_data != 0xffff) {
++		u32 reg;
++		reg = *cal_data++;
++		val = *cal_data++;
++		val |= (*cal_data++) << 16;
++
++		writel(val, mem + reg);
++		udelay(100);
++	}
++
++	pci_read_config_dword(dev, PCI_VENDOR_ID, &val);
++	dev->vendor = val & 0xffff;
++	dev->device = (val >> 16) & 0xffff;
++
++	pci_read_config_dword(dev, PCI_CLASS_REVISION, &val);
++	dev->revision = val & 0xff;
++	dev->class = val >> 8; /* upper 3 bytes */
++
++	pci_read_config_word(dev, PCI_COMMAND, &cmd);
++	cmd &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
++	pci_write_config_word(dev, PCI_COMMAND, cmd);
++
++	pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, bar0);
++
++	iounmap(mem);
++
++	dev->dev.platform_data = pdata;
++}
++DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup);
++
++void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset)
++{
++	if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups))
++		return;
++
++	ath9k_fixups[ath9k_num_fixups].slot = slot;
++
++	if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset))
++		return;
++
++	if (bcm63xx_nvram_get_mac_address(ath9k_fixups[ath9k_num_fixups].mac))
++		return;
++
++	ath9k_fixups[ath9k_num_fixups].pdata.macaddr = ath9k_fixups[ath9k_num_fixups].mac;
++	ath9k_num_fixups++;
++}
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
+@@ -0,0 +1,7 @@
++#ifndef _PCI_ATH9K_FIXUP
++#define _PCI_ATH9K_FIXUP
++
++
++void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init;
++
++#endif /* _PCI_ATH9K_FIXUP */

target/linux/brcm63xx/patches-3.8/436-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch

@@ -0,0 +1,120 @@
+Allow bcm63xxpart to receive a caldata offset if calibration data is
+contained in flash.
+---
+ drivers/mtd/bcm63xxpart.c      |   51 ++++++++++++++++++++++++++++++++++++---
+ include/linux/mtd/partitions.h |    2 +
+ 2 files changed, 49 insertions(+), 4 deletions(-)
+
+--- a/drivers/mtd/bcm63xxpart.c
++++ b/drivers/mtd/bcm63xxpart.c
+@@ -76,10 +76,12 @@ static int bcm63xx_parse_cfe_partitions(
+ 	struct mtd_partition *parts;
+ 	int ret;
+ 	size_t retlen;
+-	unsigned int rootfsaddr, kerneladdr, spareaddr;
++	unsigned int rootfsaddr, kerneladdr, spareaddr, nvramaddr;
+ 	unsigned int rootfslen, kernellen, sparelen, totallen;
+ 	unsigned int cfelen, nvramlen;
+ 	unsigned int cfe_erasesize;
++	unsigned int caldatalen1 = 0, caldataaddr1 = 0;
++	unsigned int caldatalen2 = 0, caldataaddr2 = 0;
+ 	int i;
+ 	u32 computed_crc;
+ 	bool rootfs_first = false;
+@@ -93,6 +95,24 @@ static int bcm63xx_parse_cfe_partitions(
+ 	cfelen = cfe_erasesize;
+ 	nvramlen = bcm63xx_nvram_get_psi_size() * 1024;
+ 	nvramlen = roundup(nvramlen, cfe_erasesize);
++	nvramaddr = master->size - nvramlen;
++
++	if (data) {
++		if (data->caldata[0]) {
++			caldatalen1 = cfe_erasesize;
++			caldataaddr1 = rounddown(data->caldata[0],
++						 cfe_erasesize);
++		}
++		if (data->caldata[1]) {
++			caldatalen2 = cfe_erasesize;
++			caldataaddr2 = rounddown(data->caldata[1],
++						 cfe_erasesize);
++		}
++		if (caldataaddr1 == caldataaddr2) {
++			caldataaddr2 = 0;
++			caldatalen2 = 0;
++		}
++	}
+ 
+ 	/* Allocate memory for buffer */
+ 	buf = vmalloc(sizeof(struct bcm_tag));
+@@ -144,7 +164,7 @@ static int bcm63xx_parse_cfe_partitions(
+ 		rootfsaddr = 0;
+ 		spareaddr = cfelen;
+ 	}
+-	sparelen = master->size - spareaddr - nvramlen;
++	sparelen = min_not_zero(nvramaddr, caldataaddr1) - spareaddr;
+ 
+ 	/* Determine number of partitions */
+ 	if (rootfslen > 0)
+@@ -153,6 +173,12 @@ static int bcm63xx_parse_cfe_partitions(
+ 	if (kernellen > 0)
+ 		nrparts++;
+ 
++	if (caldatalen1 > 0)
++		nrparts++;
++
++	if (caldatalen2 > 0)
++		nrparts++;
++
+ 	/* Ask kernel for more memory */
+ 	parts = kzalloc(sizeof(*parts) * nrparts + 10 * nrparts, GFP_KERNEL);
+ 	if (!parts) {
+@@ -190,15 +216,32 @@ static int bcm63xx_parse_cfe_partitions(
+ 		curpart++;
+ 	}
+ 
++	if (caldatalen1 > 0) {
++		if (caldatalen2 > 0)
++			parts[curpart].name = "cal_data1";
++		else
++			parts[curpart].name = "cal_data";
++		parts[curpart].offset = caldataaddr1;
++		parts[curpart].size = caldatalen1;
++		curpart++;
++	}
++
++	if (caldatalen2 > 0) {
++		parts[curpart].name = "cal_data2";
++		parts[curpart].offset = caldataaddr2;
++		parts[curpart].size = caldatalen2;
++		curpart++;
++	}
++
+ 	parts[curpart].name = "nvram";
+-	parts[curpart].offset = master->size - nvramlen;
++	parts[curpart].offset = nvramaddr;
+ 	parts[curpart].size = nvramlen;
+ 	curpart++;
+ 
+ 	/* Global partition "linux" to make easy firmware upgrade */
+ 	parts[curpart].name = "linux";
+ 	parts[curpart].offset = cfelen;
+-	parts[curpart].size = master->size - cfelen - nvramlen;
++	parts[curpart].size = min_not_zero(nvramaddr, caldataaddr1) - cfelen;
+ 
+ 	for (i = 0; i < nrparts; i++)
+ 		pr_info("Partition %d is %s offset %llx and length %llx\n", i,
+--- a/include/linux/mtd/partitions.h
++++ b/include/linux/mtd/partitions.h
+@@ -58,10 +58,12 @@ struct device_node;
+ /**
+  * struct mtd_part_parser_data - used to pass data to MTD partition parsers.
+  * @origin: for RedBoot, start address of MTD device
++ * @caldata: for CFE, start address of wifi calibration data
+  * @of_node: for OF parsers, device node containing partitioning information
+  */
+ struct mtd_part_parser_data {
+ 	unsigned long origin;
++	unsigned long caldata[2];
+ 	struct device_node *of_node;
+ };
+ 

target/linux/brcm63xx/patches-3.8/437-MIPS-BCM63XX-pass-caldata-info-to-flash.patch

@@ -0,0 +1,82 @@
+From 977f8a30103b9c4992cab8f49357fe0d4274004f Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Thu, 3 May 2012 14:55:26 +0200
+Subject: [PATCH 69/80] MIPS: BCM63XX: pass caldata info to flash
+
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c              |    2 +-
+ arch/mips/bcm63xx/dev-flash.c                          |    9 ++++++++-
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h |    4 +++-
+ 3 files changed, 12 insertions(+), 3 deletions(-)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -969,7 +969,7 @@ int __init board_register_devices(void)
+ 	if (board.num_spis)
+ 		spi_register_board_info(board.spis, board.num_spis);
+ 
+-	bcm63xx_flash_register();
++	bcm63xx_flash_register(board.has_caldata, board.caldata);
+ 
+ 	/* count number of LEDs defined by this device */
+ 	while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name)
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -35,12 +35,15 @@ static struct mtd_partition mtd_partitio
+ 	}
+ };
+ 
++static struct mtd_part_parser_data bcm63xx_parser_data;
++
+ static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL };
+ 
+ static struct physmap_flash_data flash_data = {
+ 	.width			= 2,
+ 	.parts			= mtd_partitions,
+ 	.part_probe_types	= bcm63xx_part_types,
++	.pp_data		= &bcm63xx_parser_data,
+ };
+ 
+ static struct resource mtd_resources[] = {
+@@ -62,6 +65,7 @@ static struct platform_device mtd_dev =
+ 
+ static struct flash_platform_data bcm63xx_flash_data = {
+ 	.part_probe_types	= bcm63xx_part_types,
++	.pp_data		= &bcm63xx_parser_data,
+ };
+ 
+ static struct spi_board_info bcm63xx_spi_flash_info[] = {
+@@ -142,10 +146,13 @@ static int __init bcm63xx_detect_flash_t
+ 	return 0;
+ }
+ 
+-int __init bcm63xx_flash_register(void)
++int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata)
+ {
+ 	u32 val;
++	unsigned int i;
+ 
++	for (i = 0; i < num_caldata; i++)
++		bcm63xx_parser_data.caldata[i] = caldata[i].caldata_offset;
+ 
+ 	bcm63xx_detect_flash_type();
+ 
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
+@@ -1,6 +1,8 @@
+ #ifndef __BCM63XX_FLASH_H
+ #define __BCM63XX_FLASH_H
+ 
++#include <board_bcm963xx.h>
++
+ enum {
+ 	BCM63XX_FLASH_TYPE_PARALLEL,
+ 	BCM63XX_FLASH_TYPE_SERIAL,
+@@ -9,6 +11,6 @@ enum {
+ 
+ extern int bcm63xx_attached_flash;
+ 
+-int __init bcm63xx_flash_register(void);
++int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata);
+ 
+ #endif /* __BCM63XX_FLASH_H */

target/linux/brcm63xx/patches-3.8/439-MIPS-BCM63XX-wire-up-the-HS-SPI-controller-for-BCM63.patch

@@ -0,0 +1,56 @@
+From ed225910f0e062d9c28d5cf216f97b3cf457a8c5 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Mon, 21 Nov 2011 00:55:49 +0100
+Subject: [PATCH 58/81] MIPS: BCM63XX: wire up the HS SPI controller for BCM6362
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/clk.c                            |    2 ++
+ arch/mips/bcm63xx/dev-hsspi.c                      |    7 +++++--
+ .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h   |    1 +
+ 3 files changed, 8 insertions(+), 2 deletions(-)
+
+--- a/arch/mips/bcm63xx/clk.c
++++ b/arch/mips/bcm63xx/clk.c
+@@ -232,6 +232,8 @@ static void hsspi_set(struct clk *clk, i
+ 
+ 	if (BCMCPU_IS_6328())
+ 		mask = CKCTL_6328_HSSPI_EN;
++	else if (BCMCPU_IS_6362())
++		mask = CKCTL_6362_HSSPI_EN;
+ 	else
+ 		return;
+ 
+--- a/arch/mips/bcm63xx/dev-hsspi.c
++++ b/arch/mips/bcm63xx/dev-hsspi.c
+@@ -43,7 +43,7 @@ static struct platform_device bcm63xx_hs
+ int __init bcm63xx_hsspi_register(void)
+ {
+ 
+-	if (!BCMCPU_IS_6328())
++	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362())
+ 		return -ENODEV;
+ 
+ 	spi_resources[0].start = bcm63xx_regset_address(RSET_HSSPI);
+@@ -51,7 +51,10 @@ int __init bcm63xx_hsspi_register(void)
+ 	spi_resources[0].end += RSET_HSSPI_SIZE - 1;
+ 	spi_resources[1].start = bcm63xx_get_irq_number(IRQ_HSSPI);
+ 
+-	spi_pdata.speed_hz = HSSPI_PLL_HZ_6328;
++	if (BCMCPU_IS_6328())
++		spi_pdata.speed_hz = HSSPI_PLL_HZ_6328;
++	else
++		spi_pdata.speed_hz = HSSPI_PLL_HZ;
+ 
+ 	return platform_device_register(&bcm63xx_hsspi_device);
+ }
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
+@@ -16,6 +16,7 @@ struct bcm63xx_hsspi_pdata {
+ #define bcm_hsspi_writel(v, o)	bcm_rset_writel(RSET_HSSPI, (v), (o))
+ 
+ #define HSSPI_PLL_HZ_6328	133333333
++#define HSSPI_PLL_HZ		400000000
+ 
+ #define HSSPI_BUFFER_LEN   	512
+ 

target/linux/brcm63xx/patches-3.8/440-MIPS-BCM63XX-enable-SPI-controller-for-BCM6362.patch

@@ -0,0 +1,101 @@
+From eef84812bc7ffd590da6ad6b83bfeebaa43a7055 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Thu, 5 Jul 2012 21:19:20 +0200
+Subject: [PATCH 58/84] MIPS: BCM63XX: enable SPI controller for BCM6362
+
+---
+ arch/mips/bcm63xx/clk.c                            |    2 ++
+ arch/mips/bcm63xx/dev-spi.c                        |   11 ++++++++++-
+ .../include/asm/mach-bcm63xx/bcm63xx_dev_spi.h     |    3 +++
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h  |   16 ++++++++++++++++
+ 4 files changed, 31 insertions(+), 1 deletions(-)
+
+--- a/arch/mips/bcm63xx/clk.c
++++ b/arch/mips/bcm63xx/clk.c
+@@ -213,6 +213,8 @@ static void spi_set(struct clk *clk, int
+ 		mask = CKCTL_6348_SPI_EN;
+ 	else if (BCMCPU_IS_6358())
+ 		mask = CKCTL_6358_SPI_EN;
++	else if (BCMCPU_IS_6362())
++		mask = CKCTL_6362_SPI_EN;
+ 	else
+ 		/* BCMCPU_IS_6368 */
+ 		mask = CKCTL_6368_SPI_EN;
+--- a/arch/mips/bcm63xx/dev-spi.c
++++ b/arch/mips/bcm63xx/dev-spi.c
+@@ -34,6 +34,10 @@ static const unsigned long bcm6358_regs_
+ 	__GEN_SPI_REGS_TABLE(6358)
+ };
+ 
++static const unsigned long bcm6362_regs_spi[] = {
++	__GEN_SPI_REGS_TABLE(6362)
++};
++
+ static const unsigned long bcm6368_regs_spi[] = {
+ 	__GEN_SPI_REGS_TABLE(6368)
+ };
+@@ -49,6 +53,8 @@ static __init void bcm63xx_spi_regs_init
+ 		bcm63xx_regs_spi = bcm6348_regs_spi;
+ 	if (BCMCPU_IS_6358())
+ 		bcm63xx_regs_spi = bcm6358_regs_spi;
++	if (BCMCPU_IS_6362())
++		bcm63xx_regs_spi = bcm6362_regs_spi;
+ 	if (BCMCPU_IS_6368())
+ 		bcm63xx_regs_spi = bcm6368_regs_spi;
+ }
+@@ -99,6 +105,9 @@ int __init bcm63xx_spi_register(void)
+ 	/* Set bus frequency */
+ 	spi_pdata.speed_hz = clk_get_rate(periph_clk);
+ 
++	if (BCMCPU_IS_6362())
++		spi_pdata.bus_num = 1;
++
+ 	spi_resources[0].start = bcm63xx_regset_address(RSET_SPI);
+ 	spi_resources[0].end = spi_resources[0].start;
+ 	spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI);
+@@ -110,7 +119,7 @@ int __init bcm63xx_spi_register(void)
+ 		spi_pdata.msg_ctl_width = SPI_6338_MSG_CTL_WIDTH;
+ 	}
+ 
+-	if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
++	if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) {
+ 		spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1;
+ 		spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE;
+ 		spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT;
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
+@@ -81,6 +81,9 @@ static inline unsigned long bcm63xx_spir
+ #ifdef CONFIG_BCM63XX_CPU_6358
+ 	__GEN_SPI_RSET(6358)
+ #endif
++#ifdef CONFIG_BCM63XX_CPU_6362
++	__GEN_SPI_RSET(6362)
++#endif
+ #ifdef CONFIG_BCM63XX_CPU_6368
+ 	__GEN_SPI_RSET(6368)
+ #endif
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -1393,6 +1393,22 @@
+ #define SPI_6358_MSG_TAIL		0x709
+ #define SPI_6358_RX_TAIL		0x70B
+ 
++/* BCM 6362 SPI core */
++#define SPI_6362_MSG_CTL		0x00	/* 16-bits register */
++#define SPI_6362_MSG_DATA		0x02
++#define SPI_6362_MSG_DATA_SIZE		0x21e
++#define SPI_6362_RX_DATA		0x400
++#define SPI_6362_RX_DATA_SIZE		0x220
++#define SPI_6362_CMD			0x700	/* 16-bits register */
++#define SPI_6362_INT_STATUS		0x702
++#define SPI_6362_INT_MASK_ST		0x703
++#define SPI_6362_INT_MASK		0x704
++#define SPI_6362_ST			0x705
++#define SPI_6362_CLK_CFG		0x706
++#define SPI_6362_FILL_BYTE		0x707
++#define SPI_6362_MSG_TAIL		0x709
++#define SPI_6362_RX_TAIL		0x70B
++
+ /* BCM 6358 SPI core */
+ #define SPI_6368_MSG_CTL		0x00	/* 16-bits register */
+ #define SPI_6368_MSG_CTL_WIDTH		16

target/linux/brcm63xx/patches-3.8/441-MIPS-BCM63XX-enable-USB-for-BCM6362.patch

@@ -0,0 +1,71 @@
+From fb9e98936590637c26b66d60137a7b44b329a254 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sun, 12 Feb 2012 14:40:56 +0100
+Subject: [PATCH 59/84] MIPS: BCM63XX: enable USB for BCM6362
+
+BCM6362 has the same USB controller as BCM6368.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ arch/mips/bcm63xx/Kconfig        |    2 ++
+ arch/mips/bcm63xx/clk.c          |    4 ++++
+ arch/mips/bcm63xx/dev-usb-ehci.c |    3 ++-
+ arch/mips/bcm63xx/dev-usb-ohci.c |    2 +-
+ drivers/usb/host/ehci-bcm63xx.c  |    2 +-
+ drivers/usb/host/ohci-bcm63xx.c  |    2 +-
+ 6 files changed, 11 insertions(+), 4 deletions(-)
+
+--- a/arch/mips/bcm63xx/Kconfig
++++ b/arch/mips/bcm63xx/Kconfig
+@@ -40,6 +40,8 @@ config BCM63XX_CPU_6358
+ config BCM63XX_CPU_6362
+ 	bool "support 6362 CPU"
+ 	select HW_HAS_PCI
++	select BCM63XX_OHCI
++	select BCM63XX_EHCI
+ 
+ config BCM63XX_CPU_6368
+ 	bool "support 6368 CPU"
+--- a/arch/mips/bcm63xx/clk.c
++++ b/arch/mips/bcm63xx/clk.c
+@@ -167,6 +167,8 @@ static void usbh_set(struct clk *clk, in
+ 		bcm_hwclock_set(CKCTL_6328_USBH_EN, enable);
+ 	else if (BCMCPU_IS_6348())
+ 		bcm_hwclock_set(CKCTL_6348_USBH_EN, enable);
++	else if (BCMCPU_IS_6362())
++		bcm_hwclock_set(CKCTL_6362_USBH_EN, enable);
+ 	else if (BCMCPU_IS_6368())
+ 		bcm_hwclock_set(CKCTL_6368_USBH_EN, enable);
+ 	else
+--- a/arch/mips/bcm63xx/dev-usb-ehci.c
++++ b/arch/mips/bcm63xx/dev-usb-ehci.c
+@@ -81,7 +81,8 @@ static struct platform_device bcm63xx_eh
+ 
+ int __init bcm63xx_ehci_register(void)
+ {
+-	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6368())
++	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6362() &&
++	    !BCMCPU_IS_6368())
+ 		return 0;
+ 
+ 	ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0);
+--- a/arch/mips/bcm63xx/usb-common.c
++++ b/arch/mips/bcm63xx/usb-common.c
+@@ -100,7 +100,7 @@ void bcm63xx_usb_priv_ohci_cfg_set(void)
+ 		bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020,
+ 				USBH_PRIV_TEST_6358_REG);
+ 
+-	} else if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) {
++	} else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) {
+ 		reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
+ 		reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK;
+ 		reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK;
+@@ -135,7 +135,7 @@ void bcm63xx_usb_priv_ehci_cfg_set(void)
+ 		bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020,
+ 				USBH_PRIV_TEST_6358_REG);
+ 
+-	} else if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) {
++	} else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() ||  BCMCPU_IS_6368()) {
+ 		reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
+ 		reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK;
+ 		reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK;

target/linux/brcm63xx/patches-3.8/442-MIPS-BCM63XX-enable-enetsw-for-BCM6362.patch

@@ -0,0 +1,67 @@
+From eac04ec501cac3069c279ccaa72fce4f530a4071 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Sun, 8 Jul 2012 21:07:12 +0200
+Subject: [PATCH 68/72] MIPS: BCM63XX: enable enetsw for BCM6362
+
+---
+ arch/mips/bcm63xx/clk.c                               |    4 +++-
+ arch/mips/bcm63xx/dev-enet.c                          |    6 ++++--
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h |    1 +
+ 3 files changed, 8 insertions(+), 3 deletions(-)
+
+--- a/arch/mips/bcm63xx/clk.c
++++ b/arch/mips/bcm63xx/clk.c
+@@ -121,11 +121,13 @@ static void enetsw_set(struct clk *clk,
+ {
+ 	u32 mask;
+ 
+-	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368())
++	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368())
+ 		return;
+ 
+ 	if (BCMCPU_IS_6328())
+ 		mask = CKCTL_6328_ROBOSW_EN;
++	else if (BCMCPU_IS_6362())
++		mask = CKCTL_6362_ROBOSW_EN;
+ 	else
+ 		mask = CKCTL_6368_ROBOSW_EN | CKCTL_6368_SWPKT_USB_EN |
+ 			CKCTL_6368_SWPKT_SAR_EN;
+--- a/arch/mips/bcm63xx/dev-enet.c
++++ b/arch/mips/bcm63xx/dev-enet.c
+@@ -141,7 +141,7 @@ static int __init register_shared(void)
+ 	shared_res[0].end = shared_res[0].start;
+ 	shared_res[0].end += (RSET_ENETDMA_SIZE)  - 1;
+ 
+-	if (BCMCPU_IS_6328() || BCMCPU_IS_6368())
++	if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
+ 		chan_count = 32;
+ 	else
+ 		chan_count = 16;
+@@ -224,7 +224,7 @@ bcm63xx_enetsw_register(const struct bcm
+ {
+ 	int ret;
+ 
+-	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368())
++	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368())
+ 		return -ENODEV;
+ 
+ 	ret = register_shared();
+@@ -243,6 +243,8 @@ bcm63xx_enetsw_register(const struct bcm
+ 
+ 	if (BCMCPU_IS_6328())
+ 		enetsw_pd.num_ports = ENETSW_PORTS_6328;
++	else if (BCMCPU_IS_6362())
++		enetsw_pd.num_ports = ENETSW_PORTS_6362;
+ 	else if (BCMCPU_IS_6368())
+ 		enetsw_pd.num_ports = ENETSW_PORTS_6368;
+ 
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
+@@ -44,6 +44,7 @@ struct bcm63xx_enet_platform_data {
+  */
+ #define ENETSW_MAX_PORT	6
+ #define ENETSW_PORTS_6328 5 /* 4 FE PHY + 1 RGMII */
++#define ENETSW_PORTS_6362 6 /* 4 FE PHY + 2 RGMII */
+ #define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */
+ 
+ #define ENETSW_RGMII_PORT0	4

target/linux/brcm63xx/patches-3.8/443-MIPS-BCM63XX-enable-enet-for-BCM6345.patch

@@ -0,0 +1,802 @@
+From 1b0b5d325d0cc50cade62afd6a9416fb3cd1e658 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jogo@openwrt.org>
+Date: Mon, 7 Jan 2013 17:42:45 +0100
+Subject: [PATCH 69/72] 443-MIPS-BCM63XX-enable-enet-for-BCM6345.patch
+
+---
+ arch/mips/bcm63xx/dev-enet.c                       |   63 ++++++-
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h   |    3 +-
+ .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h    |   88 +++++++++
+ arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h  |   43 ++++-
+ drivers/net/ethernet/broadcom/bcm63xx_enet.c       |  199 ++++++++++++--------
+ drivers/net/ethernet/broadcom/bcm63xx_enet.h       |   15 ++
+ 6 files changed, 320 insertions(+), 91 deletions(-)
+
+--- a/arch/mips/bcm63xx/dev-enet.c
++++ b/arch/mips/bcm63xx/dev-enet.c
+@@ -9,10 +9,44 @@
+ #include <linux/init.h>
+ #include <linux/kernel.h>
+ #include <linux/platform_device.h>
++#include <linux/export.h>
+ #include <bcm63xx_dev_enet.h>
+ #include <bcm63xx_io.h>
+ #include <bcm63xx_regs.h>
+ 
++#ifdef BCMCPU_RUNTIME_DETECT
++static const unsigned long bcm6xxx_regs_enetdmac[] = {
++	[ENETDMAC_CHANCFG]	= ENETDMAC_CHANCFG_REG,
++	[ENETDMAC_IR]		= ENETDMAC_IR_REG,
++	[ENETDMAC_IRMASK]	= ENETDMAC_IRMASK_REG,
++	[ENETDMAC_MAXBURST]	= ENETDMAC_MAXBURST_REG,
++};
++
++static const unsigned long bcm6345_regs_enetdmac[] = {
++	[ENETDMAC_CHANCFG]	= ENETDMA_6345_CHANCFG_REG,
++	[ENETDMAC_IR]		= ENETDMA_6345_IR_REG,
++	[ENETDMAC_IRMASK]	= ENETDMA_6345_IRMASK_REG,
++	[ENETDMAC_MAXBURST]	= ENETDMA_6345_MAXBURST_REG,
++	[ENETDMAC_BUFALLOC]	= ENETDMA_6345_BUFALLOC_REG,
++	[ENETDMAC_RSTART]	= ENETDMA_6345_RSTART_REG,
++	[ENETDMAC_FC]		= ENETDMA_6345_FC_REG,
++	[ENETDMAC_LEN]		= ENETDMA_6345_LEN_REG,
++};
++
++const unsigned long *bcm63xx_regs_enetdmac;
++EXPORT_SYMBOL(bcm63xx_regs_enetdmac);
++
++static __init void bcm63xx_enetdmac_regs_init(void)
++{
++	if (BCMCPU_IS_6345())
++		bcm63xx_regs_enetdmac = bcm6345_regs_enetdmac;
++	else
++		bcm63xx_regs_enetdmac = bcm6xxx_regs_enetdmac;
++}
++#else
++static __init void bcm63xx_enetdmac_regs_init(void) { }
++#endif
++
+ static struct resource shared_res[] = {
+ 	{
+ 		.start		= -1, /* filled at runtime */
+@@ -137,12 +171,19 @@ static int __init register_shared(void)
+ 	if (shared_device_registered)
+ 		return 0;
+ 
++	bcm63xx_enetdmac_regs_init();
++
+ 	shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA);
+ 	shared_res[0].end = shared_res[0].start;
+-	shared_res[0].end += (RSET_ENETDMA_SIZE)  - 1;
++	if (BCMCPU_IS_6345())
++		shared_res[0].end += (RSET_6345_ENETDMA_SIZE) - 1;
++	else
++		shared_res[0].end += (RSET_ENETDMA_SIZE)  - 1;
+ 
+ 	if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
+ 		chan_count = 32;
++	else if (BCMCPU_IS_6345())
++		chan_count = 8;
+ 	else
+ 		chan_count = 16;
+ 
+@@ -172,7 +213,7 @@ int __init bcm63xx_enet_register(int uni
+ 	if (unit > 1)
+ 		return -ENODEV;
+ 
+-	if (unit == 1 && BCMCPU_IS_6338())
++	if (unit == 1 && (BCMCPU_IS_6338() || BCMCPU_IS_6345()))
+ 		return -ENODEV;
+ 
+ 	ret = register_shared();
+@@ -213,6 +254,20 @@ int __init bcm63xx_enet_register(int uni
+ 		dpd->phy_interrupt = bcm63xx_get_irq_number(IRQ_ENET_PHY);
+ 	}
+ 
++	dpd->dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK;
++	dpd->dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK;
++	if (BCMCPU_IS_6345()) {
++		dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_CHAINING_MASK;
++		dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_WRAP_EN_MASK;
++		dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_FLOWC_EN_MASK;
++		dpd->dma_chan_int_mask |= ENETDMA_IR_BUFDONE_MASK;
++		dpd->dma_chan_int_mask |= ENETDMA_IR_NOTOWNER_MASK;
++		dpd->dma_chan_width = ENETDMA_6345_CHAN_WIDTH;
++		dpd->dma_no_sram = 1;
++		dpd->dma_desc_shift = ENETDMA_6345_DESC_SHIFT;
++	} else
++		dpd->dma_chan_width = ENETDMA_CHAN_WIDTH;
++
+ 	ret = platform_device_register(pdev);
+ 	if (ret)
+ 		return ret;
+@@ -248,6 +303,10 @@ bcm63xx_enetsw_register(const struct bcm
+ 	else if (BCMCPU_IS_6368())
+ 		enetsw_pd.num_ports = ENETSW_PORTS_6368;
+ 
++	enetsw_pd.dma_chan_width = ENETDMA_CHAN_WIDTH;
++	enetsw_pd.dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK;
++	enetsw_pd.dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK;
++
+ 	ret = platform_device_register(&bcm63xx_enetsw_device);
+ 	if (ret)
+ 		return ret;
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
+@@ -175,6 +175,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6368_RSET_SPI_SIZE		1804
+ #define RSET_ENET_SIZE			2048
+ #define RSET_ENETDMA_SIZE		256
++#define RSET_6345_ENETDMA_SIZE		64
+ #define RSET_ENETDMAC_SIZE(chans)	(16 * (chans))
+ #define RSET_ENETDMAS_SIZE(chans)	(16 * (chans))
+ #define RSET_ENETSW_SIZE		65536
+@@ -305,7 +306,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6345_USBDMA_BASE		(0xfffe2800)
+ #define BCM_6345_ENET0_BASE		(0xfffe1800)
+ #define BCM_6345_ENETDMA_BASE		(0xfffe2800)
+-#define BCM_6345_ENETDMAC_BASE		(0xfffe2900)
++#define BCM_6345_ENETDMAC_BASE		(0xfffe2840)
+ #define BCM_6345_ENETDMAS_BASE		(0xfffe2a00)
+ #define BCM_6345_ENETSW_BASE		(0xdeadbeef)
+ #define BCM_6345_PCMCIA_BASE		(0xfffe2028)
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
+@@ -4,6 +4,8 @@
+ #include <linux/if_ether.h>
+ #include <linux/init.h>
+ 
++#include <bcm63xx_regs.h>
++
+ /*
+  * on board ethernet platform data
+  */
+@@ -37,6 +39,21 @@ struct bcm63xx_enet_platform_data {
+ 					  int phy_id, int reg),
+ 			  void (*mii_write)(struct net_device *dev,
+ 					    int phy_id, int reg, int val));
++
++	/* DMA channel enable mask */
++	u32 dma_chan_en_mask;
++
++	/* DMA channel interrupt mask */
++	u32 dma_chan_int_mask;
++
++	/* Set to one if DMA engine has *no* SRAM */
++	unsigned int dma_no_sram;
++
++	/* DMA channel register width */
++	unsigned int dma_chan_width;
++
++	/* DMA descriptor shift */
++	unsigned int dma_desc_shift;
+ };
+ 
+ /*
+@@ -64,6 +81,15 @@ struct bcm63xx_enetsw_platform_data {
+ 	char mac_addr[ETH_ALEN];
+ 	int num_ports;
+ 	struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
++
++	/* DMA channel enable mask */
++	u32 dma_chan_en_mask;
++
++	/* DMA channel interrupt mask */
++	u32 dma_chan_int_mask;
++
++	/* DMA channel register width */
++	unsigned int dma_chan_width;
+ };
+ 
+ int __init bcm63xx_enet_register(int unit,
+@@ -72,4 +98,66 @@ int __init bcm63xx_enet_register(int uni
+ int __init
+ bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd);
+ 
++enum bcm63xx_regs_enetdmac {
++	ENETDMAC_CHANCFG,
++	ENETDMAC_IR,
++	ENETDMAC_IRMASK,
++	ENETDMAC_MAXBURST,
++	ENETDMAC_BUFALLOC,
++	ENETDMAC_RSTART,
++	ENETDMAC_FC,
++	ENETDMAC_LEN,
++};
++
++static inline unsigned long bcm63xx_enetdmacreg(enum bcm63xx_regs_enetdmac reg)
++{
++#ifdef BCMCPU_RUNTIME_DETECT
++	extern const unsigned long *bcm63xx_regs_enetdmac;
++
++	return bcm63xx_regs_enetdmac[reg];
++#else
++#ifdef CONFIG_BCM63XX_CPU_6345
++	switch (reg) {
++	case ENETDMAC_CHANCFG:
++		return ENETDMA_6345_CHANCFG_REG;
++	case ENETDMAC_IR:
++		return ENETDMA_6345_IR_REG;
++	case ENETDMAC_IRMASK:
++		return ENETDMA_6345_IRMASK_REG;
++	case ENETDMAC_MAXBURST:
++		return ENETDMA_6345_MAXBURST_REG;
++	case ENETDMAC_BUFALLOC:
++		return ENETDMA_6345_BUFALLOC_REG;
++	case ENETDMAC_RSTART:
++		return ENETDMA_6345_RSTART_REG;
++	case ENETDMAC_FC:
++		return ENETDMA_6345_FC_REG;
++	case ENETDMAC_LEN:
++		return ENETDMA_6345_LEN_REG;
++	}
++#endif
++#if defined(CONFIG_BCM6XX_CPU_6338) || defined(CONFIG_BCM63XX_CPU_6348) \
++	defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6362) \
++	defined(CONFIG_BCM63XX_CPU_6368)
++	switch (reg) {
++	case ENETDMAC_CHANCFG:
++		return ENETDMAC_CHANCFG_REG;
++	case ENETDMAC_IR:
++		return ENETDMAC_IR_REG;
++	case ENETDMAC_IRMASK:
++		return ENETDMAC_IRMASK_REG;
++	case ENETDMAC_MAXBURST:
++		return ENETDMAC_MAXBURST_REG;
++	case ENETDMAC_BUFALLOC:
++	case ENETDMAC_RSTART:
++	case ENETDMAC_FC:
++	case ENETDMAC_LEN:
++		return 0;
++	}
++#endif
++#endif
++	return 0;
++}
++
++
+ #endif /* ! BCM63XX_DEV_ENET_H_ */
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -730,6 +730,8 @@
+ /*************************************************************************
+  * _REG relative to RSET_ENETDMA
+  *************************************************************************/
++#define ENETDMA_CHAN_WIDTH		0x10
++#define ENETDMA_6345_CHAN_WIDTH		0x40
+ 
+ /* Controller Configuration Register */
+ #define ENETDMA_CFG_REG			(0x0)
+@@ -785,31 +787,56 @@
+ /* State Ram Word 4 */
+ #define ENETDMA_SRAM4_REG(x)		(0x20c + (x) * 0x10)
+ 
++/* Broadcom 6345 ENET DMA definitions */
++#define ENETDMA_6345_CHANCFG_REG	(0x00)
++
++#define ENETDMA_6345_MAXBURST_REG	(0x40)
++
++#define ENETDMA_6345_RSTART_REG		(0x08)
++
++#define ENETDMA_6345_LEN_REG		(0x0C)
++
++#define ENETDMA_6345_IR_REG		(0x14)
++
++#define ENETDMA_6345_IRMASK_REG		(0x18)
++
++#define ENETDMA_6345_FC_REG		(0x1C)
++
++#define ENETDMA_6345_BUFALLOC_REG	(0x20)
++
++/* Shift down for EOP, SOP and WRAP bits */
++#define ENETDMA_6345_DESC_SHIFT		(3)
+ 
+ /*************************************************************************
+  * _REG relative to RSET_ENETDMAC
+  *************************************************************************/
+ 
+ /* Channel Configuration register */
+-#define ENETDMAC_CHANCFG_REG(x)		((x) * 0x10)
++#define ENETDMAC_CHANCFG_REG		(0x0)
+ #define ENETDMAC_CHANCFG_EN_SHIFT	0
+ #define ENETDMAC_CHANCFG_EN_MASK	(1 << ENETDMAC_CHANCFG_EN_SHIFT)
+ #define ENETDMAC_CHANCFG_PKTHALT_SHIFT	1
+ #define ENETDMAC_CHANCFG_PKTHALT_MASK	(1 << ENETDMAC_CHANCFG_PKTHALT_SHIFT)
+ #define ENETDMAC_CHANCFG_BUFHALT_SHIFT	2
+ #define ENETDMAC_CHANCFG_BUFHALT_MASK	(1 << ENETDMAC_CHANCFG_BUFHALT_SHIFT)
++#define ENETDMAC_CHANCFG_CHAINING_SHIFT	2
++#define ENETDMAC_CHANCFG_CHAINING_MASK	(1 << ENETDMAC_CHANCFG_CHAINING_SHIFT)
++#define ENETDMAC_CHANCFG_WRAP_EN_SHIFT	3
++#define ENETDMAC_CHANCFG_WRAP_EN_MASK	(1 << ENETDMAC_CHANCFG_WRAP_EN_SHIFT)
++#define ENETDMAC_CHANCFG_FLOWC_EN_SHIFT	4
++#define ENETDMAC_CHANCFG_FLOWC_EN_MASK	(1 << ENETDMAC_CHANCFG_FLOWC_EN_SHIFT)
+ 
+ /* Interrupt Control/Status register */
+-#define ENETDMAC_IR_REG(x)		(0x4 + (x) * 0x10)
++#define ENETDMAC_IR_REG			(0x4)
+ #define ENETDMAC_IR_BUFDONE_MASK	(1 << 0)
+ #define ENETDMAC_IR_PKTDONE_MASK	(1 << 1)
+ #define ENETDMAC_IR_NOTOWNER_MASK	(1 << 2)
+ 
+ /* Interrupt Mask register */
+-#define ENETDMAC_IRMASK_REG(x)		(0x8 + (x) * 0x10)
++#define ENETDMAC_IRMASK_REG		(0x8)
+ 
+ /* Maximum Burst Length */
+-#define ENETDMAC_MAXBURST_REG(x)	(0xc + (x) * 0x10)
++#define ENETDMAC_MAXBURST_REG		(0xc)
+ 
+ 
+ /*************************************************************************
+@@ -817,16 +844,16 @@
+  *************************************************************************/
+ 
+ /* Ring Start Address register */
+-#define ENETDMAS_RSTART_REG(x)		((x) * 0x10)
++#define ENETDMAS_RSTART_REG		(0x0)
+ 
+ /* State Ram Word 2 */
+-#define ENETDMAS_SRAM2_REG(x)		(0x4 + (x) * 0x10)
++#define ENETDMAS_SRAM2_REG		(0x4)
+ 
+ /* State Ram Word 3 */
+-#define ENETDMAS_SRAM3_REG(x)		(0x8 + (x) * 0x10)
++#define ENETDMAS_SRAM3_REG		(0x8)
+ 
+ /* State Ram Word 4 */
+-#define ENETDMAS_SRAM4_REG(x)		(0xc + (x) * 0x10)
++#define ENETDMAS_SRAM4_REG		(0xc)
+ 
+ 
+ /*************************************************************************
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -115,26 +115,28 @@ static inline void enet_dma_writel(struc
+ 	bcm_writel(val, bcm_enet_shared_base[0] + off);
+ }
+ 
+-static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off)
++static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off, int chan)
+ {
+-	return bcm_readl(bcm_enet_shared_base[1] + off);
++	return bcm_readl(bcm_enet_shared_base[1] +
++		(bcm63xx_enetdmacreg(off) + (chan * priv->dma_chan_width)));
+ }
+ 
+ static inline void enet_dmac_writel(struct bcm_enet_priv *priv,
+-				       u32 val, u32 off)
++				       u32 val, u32 off, int chan)
+ {
+-	bcm_writel(val, bcm_enet_shared_base[1] + off);
++	bcm_writel(val, bcm_enet_shared_base[1] +
++		(bcm63xx_enetdmacreg(off) + (chan * priv->dma_chan_width)));
+ }
+ 
+-static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off)
++static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off, int chan)
+ {
+-	return bcm_readl(bcm_enet_shared_base[2] + off);
++	return bcm_readl(bcm_enet_shared_base[2] + (off + (chan * priv->dma_chan_width)));
+ }
+ 
+ static inline void enet_dmas_writel(struct bcm_enet_priv *priv,
+-				       u32 val, u32 off)
++				       u32 val, u32 off, int chan)
+ {
+-	bcm_writel(val, bcm_enet_shared_base[2] + off);
++	bcm_writel(val, bcm_enet_shared_base[2] + (off + (chan * priv->dma_chan_width)));
+ }
+ 
+ /*
+@@ -270,7 +272,7 @@ static int bcm_enet_refill_rx(struct net
+ 		len_stat = priv->rx_skb_size << DMADESC_LENGTH_SHIFT;
+ 		len_stat |= DMADESC_OWNER_MASK;
+ 		if (priv->rx_dirty_desc == priv->rx_ring_size - 1) {
+-			len_stat |= DMADESC_WRAP_MASK;
++			len_stat |= (DMADESC_WRAP_MASK >> priv->dma_desc_shift);
+ 			priv->rx_dirty_desc = 0;
+ 		} else {
+ 			priv->rx_dirty_desc++;
+@@ -281,7 +283,10 @@ static int bcm_enet_refill_rx(struct net
+ 		priv->rx_desc_count++;
+ 
+ 		/* tell dma engine we allocated one buffer */
+-		enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan));
++		if (!priv->dma_no_sram)
++			enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan));
++		else
++			enet_dmac_writel(priv, 1, ENETDMAC_BUFALLOC, priv->rx_chan);
+ 	}
+ 
+ 	/* If rx ring is still empty, set a timer to try allocating
+@@ -357,7 +362,8 @@ static int bcm_enet_receive_queue(struct
+ 
+ 		/* if the packet does not have start of packet _and_
+ 		 * end of packet flag set, then just recycle it */
+-		if ((len_stat & DMADESC_ESOP_MASK) != DMADESC_ESOP_MASK) {
++		if ((len_stat & (DMADESC_ESOP_MASK >> priv->dma_desc_shift)) !=
++			(DMADESC_ESOP_MASK >> priv->dma_desc_shift)) {
+ 			dev->stats.rx_dropped++;
+ 			continue;
+ 		}
+@@ -418,8 +424,8 @@ static int bcm_enet_receive_queue(struct
+ 		bcm_enet_refill_rx(dev);
+ 
+ 		/* kick rx dma */
+-		enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
+-				 ENETDMAC_CHANCFG_REG(priv->rx_chan));
++		enet_dmac_writel(priv, priv->dma_chan_en_mask,
++					 ENETDMAC_CHANCFG, priv->rx_chan);
+ 	}
+ 
+ 	return processed;
+@@ -494,10 +500,10 @@ static int bcm_enet_poll(struct napi_str
+ 	dev = priv->net_dev;
+ 
+ 	/* ack interrupts */
+-	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IR_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IR_REG(priv->tx_chan));
++	enet_dmac_writel(priv, priv->dma_chan_int_mask,
++			 ENETDMAC_IR, priv->rx_chan);
++	enet_dmac_writel(priv, priv->dma_chan_int_mask,
++			 ENETDMAC_IR, priv->tx_chan);
+ 
+ 	/* reclaim sent skb */
+ 	tx_work_done = bcm_enet_tx_reclaim(dev, 0);
+@@ -516,10 +522,10 @@ static int bcm_enet_poll(struct napi_str
+ 	napi_complete(napi);
+ 
+ 	/* restore rx/tx interrupt */
+-	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IRMASK_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, priv->dma_chan_int_mask,
++			 ENETDMAC_IRMASK, priv->rx_chan);
++	enet_dmac_writel(priv, priv->dma_chan_int_mask,
++			 ENETDMAC_IRMASK, priv->tx_chan);
+ 
+ 	return rx_work_done;
+ }
+@@ -562,8 +568,8 @@ static irqreturn_t bcm_enet_isr_dma(int
+ 	priv = netdev_priv(dev);
+ 
+ 	/* mask rx/tx interrupts */
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
+ 
+ 	napi_schedule(&priv->napi);
+ 
+@@ -624,14 +630,14 @@ static int bcm_enet_start_xmit(struct sk
+ 				       DMA_TO_DEVICE);
+ 
+ 	len_stat = (skb->len << DMADESC_LENGTH_SHIFT) & DMADESC_LENGTH_MASK;
+-	len_stat |= DMADESC_ESOP_MASK |
++	len_stat |= (DMADESC_ESOP_MASK >> priv->dma_desc_shift) |
+ 		DMADESC_APPEND_CRC |
+ 		DMADESC_OWNER_MASK;
+ 
+ 	priv->tx_curr_desc++;
+ 	if (priv->tx_curr_desc == priv->tx_ring_size) {
+ 		priv->tx_curr_desc = 0;
+-		len_stat |= DMADESC_WRAP_MASK;
++		len_stat |= (DMADESC_WRAP_MASK >> priv->dma_desc_shift);
+ 	}
+ 	priv->tx_desc_count--;
+ 
+@@ -642,8 +648,8 @@ static int bcm_enet_start_xmit(struct sk
+ 	wmb();
+ 
+ 	/* kick tx dma */
+-	enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
+-			 ENETDMAC_CHANCFG_REG(priv->tx_chan));
++	enet_dmac_writel(priv, priv->dma_chan_en_mask,
++				 ENETDMAC_CHANCFG, priv->tx_chan);
+ 
+ 	/* stop queue if no more desc available */
+ 	if (!priv->tx_desc_count)
+@@ -771,6 +777,9 @@ static void bcm_enet_set_flow(struct bcm
+ 		val &= ~ENET_RXCFG_ENFLOW_MASK;
+ 	enet_writel(priv, val, ENET_RXCFG_REG);
+ 
++	if (priv->dma_no_sram)
++		return;
++
+ 	/* tx flow control (pause frame generation) */
+ 	val = enet_dma_readl(priv, ENETDMA_CFG_REG);
+ 	if (tx_en)
+@@ -886,8 +895,8 @@ static int bcm_enet_open(struct net_devi
+ 
+ 	/* mask all interrupts and request them */
+ 	enet_writel(priv, 0, ENET_IRMASK_REG);
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
+ 
+ 	ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev);
+ 	if (ret)
+@@ -966,8 +975,12 @@ static int bcm_enet_open(struct net_devi
+ 	priv->rx_curr_desc = 0;
+ 
+ 	/* initialize flow control buffer allocation */
+-	enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
+-			ENETDMA_BUFALLOC_REG(priv->rx_chan));
++	if (!priv->dma_no_sram)
++		enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
++				ENETDMA_BUFALLOC_REG(priv->rx_chan));
++	else
++		enet_dmac_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
++				ENETDMAC_BUFALLOC, priv->rx_chan);
+ 
+ 	if (bcm_enet_refill_rx(dev)) {
+ 		dev_err(kdev, "cannot allocate rx skb queue\n");
+@@ -976,18 +989,30 @@ static int bcm_enet_open(struct net_devi
+ 	}
+ 
+ 	/* write rx & tx ring addresses */
+-	enet_dmas_writel(priv, priv->rx_desc_dma,
+-			 ENETDMAS_RSTART_REG(priv->rx_chan));
+-	enet_dmas_writel(priv, priv->tx_desc_dma,
+-			 ENETDMAS_RSTART_REG(priv->tx_chan));
++	if (!priv->dma_no_sram) {
++		enet_dmas_writel(priv, priv->rx_desc_dma,
++				 ENETDMAS_RSTART_REG, priv->rx_chan);
++		enet_dmas_writel(priv, priv->tx_desc_dma,
++			 ENETDMAS_RSTART_REG, priv->tx_chan);
++	} else {
++		enet_dmac_writel(priv, priv->rx_desc_dma,
++				ENETDMAC_RSTART, priv->rx_chan);
++		enet_dmac_writel(priv, priv->tx_desc_dma,
++				ENETDMAC_RSTART, priv->tx_chan);
++	}
+ 
+ 	/* clear remaining state ram for rx & tx channel */
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan));
++	if (!priv->dma_no_sram) {
++		enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->rx_chan);
++		enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->tx_chan);
++		enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->rx_chan);
++		enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->tx_chan);
++		enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->rx_chan);
++		enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->tx_chan);
++	} else {
++		enet_dmac_writel(priv, 0, ENETDMAC_FC, priv->rx_chan);
++		enet_dmac_writel(priv, 0, ENETDMAC_FC, priv->tx_chan);
++	}
+ 
+ 	/* set max rx/tx length */
+ 	enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG);
+@@ -995,18 +1020,24 @@ static int bcm_enet_open(struct net_devi
+ 
+ 	/* set dma maximum burst len */
+ 	enet_dmac_writel(priv, priv->dma_maxburst,
+-			 ENETDMAC_MAXBURST_REG(priv->rx_chan));
++			 ENETDMAC_MAXBURST, priv->rx_chan);
+ 	enet_dmac_writel(priv, priv->dma_maxburst,
+-			 ENETDMAC_MAXBURST_REG(priv->tx_chan));
++			 ENETDMAC_MAXBURST, priv->tx_chan);
+ 
+ 	/* set correct transmit fifo watermark */
+ 	enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG);
+ 
+ 	/* set flow control low/high threshold to 1/3 / 2/3 */
+-	val = priv->rx_ring_size / 3;
+-	enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan));
+-	val = (priv->rx_ring_size * 2) / 3;
+-	enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan));
++	if (!priv->dma_no_sram) {
++		val = priv->rx_ring_size / 3;
++		enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan));
++		val = (priv->rx_ring_size * 2) / 3;
++		enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan));
++	} else {
++		enet_dmac_writel(priv, 5, ENETDMAC_FC, priv->rx_chan);
++		enet_dmac_writel(priv, priv->rx_ring_size, ENETDMAC_LEN, priv->rx_chan);
++		enet_dmac_writel(priv, priv->tx_ring_size, ENETDMAC_LEN, priv->tx_chan);
++	}
+ 
+ 	/* all set, enable mac and interrupts, start dma engine and
+ 	 * kick rx dma channel */
+@@ -1015,26 +1046,26 @@ static int bcm_enet_open(struct net_devi
+ 	val |= ENET_CTL_ENABLE_MASK;
+ 	enet_writel(priv, val, ENET_CTL_REG);
+ 	enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG);
+-	enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
+-			 ENETDMAC_CHANCFG_REG(priv->rx_chan));
++	enet_dmac_writel(priv, priv->dma_chan_en_mask,
++			 ENETDMAC_CHANCFG, priv->rx_chan);
+ 
+ 	/* watch "mib counters about to overflow" interrupt */
+ 	enet_writel(priv, ENET_IR_MIB, ENET_IR_REG);
+ 	enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG);
+ 
+ 	/* watch "packet transferred" interrupt in rx and tx */
+-	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IR_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IR_REG(priv->tx_chan));
++	enet_dmac_writel(priv, priv->dma_chan_int_mask,
++			 ENETDMAC_IR, priv->rx_chan);
++	enet_dmac_writel(priv, priv->dma_chan_int_mask,
++			 ENETDMAC_IR, priv->tx_chan);
+ 
+ 	/* make sure we enable napi before rx interrupt  */
+ 	napi_enable(&priv->napi);
+ 
+-	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IRMASK_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, priv->dma_chan_int_mask,
++			 ENETDMAC_IRMASK, priv->rx_chan);
++	enet_dmac_writel(priv, priv->dma_chan_int_mask,
++			 ENETDMAC_IRMASK, priv->tx_chan);
+ 
+ 	if (priv->has_phy)
+ 		phy_start(priv->phydev);
+@@ -1111,13 +1142,13 @@ static void bcm_enet_disable_dma(struct
+ {
+ 	int limit;
+ 
+-	enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG_REG(chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG, chan);
+ 
+ 	limit = 1000;
+ 	do {
+ 		u32 val;
+ 
+-		val = enet_dmac_readl(priv, ENETDMAC_CHANCFG_REG(chan));
++		val = enet_dmac_readl(priv, ENETDMAC_CHANCFG, chan);
+ 		if (!(val & ENETDMAC_CHANCFG_EN_MASK))
+ 			break;
+ 		udelay(1);
+@@ -1144,8 +1175,8 @@ static int bcm_enet_stop(struct net_devi
+ 
+ 	/* mask all interrupts */
+ 	enet_writel(priv, 0, ENET_IRMASK_REG);
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
+ 
+ 	/* make sure no mib update is scheduled */
+ 	cancel_work_sync(&priv->mib_update_task);
+@@ -1757,6 +1788,11 @@ static int bcm_enet_probe(struct platfor
+ 		priv->pause_tx = pd->pause_tx;
+ 		priv->force_duplex_full = pd->force_duplex_full;
+ 		priv->force_speed_100 = pd->force_speed_100;
++		priv->dma_chan_en_mask = pd->dma_chan_en_mask;
++		priv->dma_chan_int_mask = pd->dma_chan_int_mask;
++		priv->dma_chan_width = pd->dma_chan_width;
++		priv->dma_no_sram = pd->dma_no_sram;
++		priv->dma_desc_shift = pd->dma_desc_shift;
+ 	}
+ 
+ 	if (priv->mac_id == 0 && priv->has_phy && !priv->use_external_mii) {
+@@ -2144,8 +2180,8 @@ static int bcm_enetsw_open(struct net_de
+ 	kdev = &priv->pdev->dev;
+ 
+ 	/* mask all interrupts and request them */
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
+ 
+ 	ret = request_irq(priv->irq_rx, bcm_enet_isr_dma,
+ 			  IRQF_DISABLED, dev->name, dev);
+@@ -2269,23 +2305,23 @@ static int bcm_enetsw_open(struct net_de
+ 
+ 	/* write rx & tx ring addresses */
+ 	enet_dmas_writel(priv, priv->rx_desc_dma,
+-			 ENETDMAS_RSTART_REG(priv->rx_chan));
++			 ENETDMAS_RSTART_REG, priv->rx_chan);
+ 	enet_dmas_writel(priv, priv->tx_desc_dma,
+-			 ENETDMAS_RSTART_REG(priv->tx_chan));
++			 ENETDMAS_RSTART_REG, priv->tx_chan);
+ 
+ 	/* clear remaining state ram for rx & tx channel */
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan));
+-	enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan));
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->rx_chan);
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->tx_chan);
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->rx_chan);
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->tx_chan);
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->rx_chan);
++	enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->tx_chan);
+ 
+ 	/* set dma maximum burst len */
+ 	enet_dmac_writel(priv, priv->dma_maxburst,
+-			 ENETDMAC_MAXBURST_REG(priv->rx_chan));
++			 ENETDMAC_MAXBURST, priv->rx_chan);
+ 	enet_dmac_writel(priv, priv->dma_maxburst,
+-			 ENETDMAC_MAXBURST_REG(priv->tx_chan));
++			 ENETDMAC_MAXBURST, priv->tx_chan);
+ 
+ 	/* set flow control low/high threshold to 1/3 / 2/3 */
+ 	val = priv->rx_ring_size / 3;
+@@ -2298,21 +2334,21 @@ static int bcm_enetsw_open(struct net_de
+ 	wmb();
+ 	enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG);
+ 	enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
+-			 ENETDMAC_CHANCFG_REG(priv->rx_chan));
++			 ENETDMAC_CHANCFG, priv->rx_chan);
+ 
+ 	/* watch "packet transferred" interrupt in rx and tx */
+ 	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IR_REG(priv->rx_chan));
++			 ENETDMAC_IR, priv->rx_chan);
+ 	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IR_REG(priv->tx_chan));
++			 ENETDMAC_IR, priv->tx_chan);
+ 
+ 	/* make sure we enable napi before rx interrupt  */
+ 	napi_enable(&priv->napi);
+ 
+ 	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IRMASK_REG(priv->rx_chan));
++			 ENETDMAC_IRMASK, priv->rx_chan);
+ 	enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
+-			 ENETDMAC_IRMASK_REG(priv->tx_chan));
++			 ENETDMAC_IRMASK, priv->tx_chan);
+ 
+ 	netif_carrier_on(dev);
+ 	netif_start_queue(dev);
+@@ -2419,8 +2455,8 @@ static int bcm_enetsw_stop(struct net_de
+ 	del_timer_sync(&priv->rx_timeout);
+ 
+ 	/* mask all interrupts */
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
+-	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
++	enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
+ 
+ 	/* disable dma & mac */
+ 	bcm_enet_disable_dma(priv, priv->tx_chan);
+@@ -2757,6 +2793,9 @@ static int bcm_enetsw_probe(struct platf
+ 		memcpy(priv->used_ports, pd->used_ports,
+ 		       sizeof (pd->used_ports));
+ 		priv->num_ports = pd->num_ports;
++		priv->dma_chan_en_mask = pd->dma_chan_en_mask;
++		priv->dma_chan_int_mask = pd->dma_chan_int_mask;
++		priv->dma_chan_width = pd->dma_chan_width;
+ 	}
+ 
+ 	ret = compute_hw_mtu(priv, dev->mtu);
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h
+@@ -339,6 +339,21 @@ struct bcm_enet_priv {
+ 	/* used to poll switch port state */
+ 	struct timer_list swphy_poll;
+ 	spinlock_t enetsw_mdio_lock;
++
++	/* dma channel enable mask */
++	u32 dma_chan_en_mask;
++
++	/* dma channel interrupt mask */
++	u32 dma_chan_int_mask;
++
++	/* dma engine has *no* internal SRAM */
++	unsigned int dma_no_sram;
++
++	/* dma channel width */
++	unsigned int dma_chan_width;
++
++	/* dma descriptor shift value */
++	unsigned int dma_desc_shift;
+ };
+ 
+ static inline int bcm_enet_port_is_rgmii(int portid)

target/linux/brcm63xx/patches-3.8/444-BCM63XX-add-endian-check-for-ath9k.patch

@@ -0,0 +1,51 @@
+--- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
++++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
+@@ -2,6 +2,7 @@
+ #define _PCI_ATH9K_FIXUP
+ 
+ 
+-void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init;
++void pci_enable_ath9k_fixup(unsigned slot, u32 offset,
++	unsigned endian_check) __init;
+ 
+ #endif /* _PCI_ATH9K_FIXUP */
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -19,6 +19,7 @@
+ struct ath9k_caldata {
+ 	unsigned int	slot;
+ 	u32		caldata_offset;
++	unsigned int	endian_check:1;
+ };
+ 
+ /*
+--- a/arch/mips/bcm63xx/pci-ath9k-fixup.c
++++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c
+@@ -172,12 +172,14 @@ static void ath9k_pci_fixup(struct pci_d
+ }
+ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup);
+ 
+-void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset)
++void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset,
++	unsigned endian_check)
+ {
+ 	if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups))
+ 		return;
+ 
+ 	ath9k_fixups[ath9k_num_fixups].slot = slot;
++	ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check;
+ 
+ 	if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset))
+ 		return;
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -995,7 +995,8 @@ int __init board_register_devices(void)
+ 
+ 	/* register any fixups */
+ 	for (i = 0; i < board.has_caldata; i++)
+-		pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset);
++		pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset,
++			board.caldata[i].endian_check);
+ 
+ 	return 0;
+ }

target/linux/brcm63xx/patches-3.8/445-BCM63XX-add-led-pin-for-ath9k.patch

@@ -0,0 +1,49 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -996,7 +996,7 @@ int __init board_register_devices(void)
+ 	/* register any fixups */
+ 	for (i = 0; i < board.has_caldata; i++)
+ 		pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset,
+-			board.caldata[i].endian_check);
++			board.caldata[i].endian_check, board.caldata[i].led_pin);
+ 
+ 	return 0;
+ }
+--- a/arch/mips/bcm63xx/pci-ath9k-fixup.c
++++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c
+@@ -173,13 +173,14 @@ static void ath9k_pci_fixup(struct pci_d
+ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup);
+ 
+ void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset,
+-	unsigned endian_check)
++	unsigned endian_check, int led_pin)
+ {
+ 	if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups))
+ 		return;
+ 
+ 	ath9k_fixups[ath9k_num_fixups].slot = slot;
+ 	ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check;
++	ath9k_fixups[ath9k_num_fixups].pdata.led_pin = led_pin;
+ 
+ 	if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset))
+ 		return;
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -20,6 +20,7 @@ struct ath9k_caldata {
+ 	unsigned int	slot;
+ 	u32		caldata_offset;
+ 	unsigned int	endian_check:1;
++	int		led_pin;
+ };
+ 
+ /*
+--- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
++++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
+@@ -3,6 +3,6 @@
+ 
+ 
+ void pci_enable_ath9k_fixup(unsigned slot, u32 offset,
+-	unsigned endian_check) __init;
++	unsigned endian_check, int led_pin) __init;
+ 
+ #endif /* _PCI_ATH9K_FIXUP */

target/linux/brcm63xx/patches-3.8/446-BCM63XX-add-a-fixup-for-rt2x00-devices.patch

@@ -0,0 +1,205 @@
+From 5ed5b5e9614fa5b02da699ab565af76c7e63d64d Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jogo@openwrt.org>
+Date: Mon, 7 Jan 2013 17:45:39 +0100
+Subject: [PATCH 72/72] 446-BCM63XX-add-a-fixup-for-rt2x00-devices
+
+---
+ arch/mips/bcm63xx/Makefile                         |    2 +-
+ arch/mips/bcm63xx/boards/board_bcm963xx.c          |   17 ++++-
+ arch/mips/bcm63xx/dev-flash.c                      |    2 +-
+ arch/mips/bcm63xx/pci-rt2x00-fixup.c               |   71 ++++++++++++++++++++
+ .../include/asm/mach-bcm63xx/bcm63xx_dev_flash.h   |    2 +-
+ .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h |    9 ++-
+ .../include/asm/mach-bcm63xx/pci_rt2x00_fixup.h    |    9 +++
+ 7 files changed, 104 insertions(+), 8 deletions(-)
+ create mode 100644 arch/mips/bcm63xx/pci-rt2x00-fixup.c
+ create mode 100644 arch/mips/include/asm/mach-bcm63xx/pci_rt2x00_fixup.h
+
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -2,7 +2,7 @@ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o
+ 		   setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
+ 		   dev-hsspi.o dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o \
+ 		   dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \
+-		   pci-ath9k-fixup.o usb-common.o
++		   pci-ath9k-fixup.o pci-rt2x00-fixup.o usb-common.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -34,6 +34,7 @@
+ #include <bcm63xx_dev_usb_usbd.h>
+ #include <board_bcm963xx.h>
+ #include <pci_ath9k_fixup.h>
++#include <pci_rt2x00_fixup.h>
+ 
+ #include <uapi/linux/bcm963xx_tag.h>
+ 
+@@ -994,9 +995,19 @@ int __init board_register_devices(void)
+ 	}
+ 
+ 	/* register any fixups */
+-	for (i = 0; i < board.has_caldata; i++)
+-		pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset,
+-			board.caldata[i].endian_check, board.caldata[i].led_pin);
++	for (i = 0; i < board.has_caldata; i++) {
++		switch (board.caldata[i].vendor) {
++		case PCI_VENDOR_ID_ATHEROS:
++			pci_enable_ath9k_fixup(board.caldata[i].slot,
++				board.caldata[i].caldata_offset, board.caldata[i].endian_check,
++				board.caldata[i].led_pin);
++			break;
++		case PCI_VENDOR_ID_RALINK:
++			pci_enable_rt2x00_fixup(board.caldata[i].slot,
++				board.caldata[i].eeprom);
++			break;
++		}
++	}
+ 
+ 	return 0;
+ }
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -146,7 +146,7 @@ static int __init bcm63xx_detect_flash_t
+ 	return 0;
+ }
+ 
+-int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata)
++int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata)
+ {
+ 	u32 val;
+ 	unsigned int i;
+--- /dev/null
++++ b/arch/mips/bcm63xx/pci-rt2x00-fixup.c
+@@ -0,0 +1,72 @@
++/*
++ *  Broadcom BCM63XX RT2x00 EEPROM fixup helper.
++ *
++ *  Copyright (C) 2012 Álvaro Fernández Rojas <noltari@gmail.com>
++ *
++ *  Based on
++ *
++ *  Broadcom BCM63XX Ath9k EEPROM fixup helper.
++ *
++ *  Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
++ *
++ *  This program is free software; you can redistribute it and/or modify it
++ *  under the terms of the GNU General Public License version 2 as published
++ *  by the Free Software Foundation.
++ */
++
++#include <linux/if_ether.h>
++#include <linux/pci.h>
++#include <linux/platform_device.h>
++#include <linux/rt2x00_platform.h>
++
++#include <bcm63xx_nvram.h>
++#include <pci_rt2x00_fixup.h>
++
++struct rt2x00_fixup {
++	unsigned slot;
++	u8 mac[ETH_ALEN];
++	struct rt2x00_platform_data pdata;
++};
++
++static int rt2x00_num_fixups;
++static struct rt2x00_fixup rt2x00_fixups[2] = {
++	{
++		.slot = 255,
++	},
++	{
++		.slot = 255,
++	},
++};
++
++static void rt2x00_pci_fixup(struct pci_dev *dev)
++{
++	unsigned i;
++	struct rt2x00_platform_data *pdata = NULL;
++
++	for (i = 0; i < rt2x00_num_fixups; i++) {
++		if (rt2x00_fixups[i].slot != PCI_SLOT(dev->devfn))
++			continue;
++
++		pdata = &rt2x00_fixups[i].pdata;
++		break;
++	}
++
++	dev->dev.platform_data = pdata;
++}
++DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_RALINK, PCI_ANY_ID, rt2x00_pci_fixup);
++
++void __init pci_enable_rt2x00_fixup(unsigned slot, char* eeprom)
++{
++	if (rt2x00_num_fixups >= ARRAY_SIZE(rt2x00_fixups))
++		return;
++
++	rt2x00_fixups[rt2x00_num_fixups].slot = slot;
++	rt2x00_fixups[rt2x00_num_fixups].pdata.eeprom_file_name = kstrdup(eeprom, GFP_KERNEL);
++
++	if (bcm63xx_nvram_get_mac_address(rt2x00_fixups[rt2x00_num_fixups].mac))
++		return;
++
++	rt2x00_fixups[rt2x00_num_fixups].pdata.mac_address = rt2x00_fixups[rt2x00_num_fixups].mac;
++	rt2x00_num_fixups++;
++}
++
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
+@@ -11,6 +11,6 @@ enum {
+ 
+ extern int bcm63xx_attached_flash;
+ 
+-int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata);
++int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata);
+ 
+ #endif /* __BCM63XX_FLASH_H */
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -9,6 +9,7 @@
+ #include <bcm63xx_dev_usb_usbd.h>
+ #include <bcm63xx_dev_dsp.h>
+ #include <pci_ath9k_fixup.h>
++#include <pci_rt2x00_fixup.h>
+ 
+ /*
+  * flash mapping
+@@ -16,11 +17,15 @@
+ #define BCM963XX_CFE_VERSION_OFFSET	0x570
+ #define BCM963XX_NVRAM_OFFSET		0x580
+ 
+-struct ath9k_caldata {
++struct bcm63xx_caldata {
++	unsigned int	vendor;
+ 	unsigned int	slot;
+ 	u32		caldata_offset;
++	/* Atheros */
+ 	unsigned int	endian_check:1;
+ 	int		led_pin;
++	/* Ralink */
++	char*		eeprom;
+ };
+ 
+ /*
+@@ -45,7 +50,7 @@ struct board_info {
+ 	unsigned int	has_caldata:2;
+ 
+ 	/* wifi calibration data config */
+-	struct ath9k_caldata caldata[2];
++	struct bcm63xx_caldata caldata[2];
+ 
+ 	/* ethernet config */
+ 	struct bcm63xx_enet_platform_data enet0;
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/pci_rt2x00_fixup.h
+@@ -0,0 +1,9 @@
++#ifndef _PCI_RT2X00_FIXUP
++#define _PCI_RT2X00_FIXUP
++
++#define PCI_VENDOR_ID_RALINK 0x1814
++
++void pci_enable_rt2x00_fixup(unsigned slot, char* eeprom) __init;
++
++#endif /* _PCI_RT2X00_FIXUP */
++

target/linux/brcm63xx/patches-3.8/447-bcm63xx_enet_add_b53_support.patch

@@ -0,0 +1,169 @@
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h
+@@ -336,6 +336,9 @@ struct bcm_enet_priv {
+ 	struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
+ 	int sw_port_link[ENETSW_MAX_PORT];
+ 
++	/* platform device for associated switch */
++	struct platform_device *b53_device;
++
+ 	/* used to poll switch port state */
+ 	struct timer_list swphy_poll;
+ 	spinlock_t enetsw_mdio_lock;
+--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+@@ -30,6 +30,7 @@
+ #include <linux/dma-mapping.h>
+ #include <linux/platform_device.h>
+ #include <linux/if_vlan.h>
++#include <linux/platform_data/b53.h>
+ 
+ #include <bcm63xx_dev_enet.h>
+ #include "bcm63xx_enet.h"
+@@ -2013,7 +2014,8 @@ static int bcm_enet_remove(struct platfo
+ 	return 0;
+ }
+ 
+-struct platform_driver bcm63xx_enet_driver = {
++
++static struct platform_driver bcm63xx_enet_driver = {
+ 	.probe	= bcm_enet_probe,
+ 	.remove	= bcm_enet_remove,
+ 	.driver	= {
+@@ -2022,6 +2024,42 @@ struct platform_driver bcm63xx_enet_driv
+ 	},
+ };
+ 
++struct b53_platform_data bcm63xx_b53_pdata = {
++	.chip_id = 0x6300,
++	.big_endian = 1,
++};
++
++struct platform_device bcm63xx_b53_dev = {
++	.name		= "b53-switch",
++	.id		= -1,
++	.dev		= {
++		.platform_data = &bcm63xx_b53_pdata,
++	},
++};
++
++static int bcmenet_switch_register(struct bcm_enet_priv *priv, u16 port_mask)
++{
++	int ret;
++
++	bcm63xx_b53_pdata.regs = priv->base;
++	bcm63xx_b53_pdata.enabled_ports = port_mask;
++	bcm63xx_b53_pdata.alias = priv->net_dev->name;
++
++	ret = platform_device_register(&bcm63xx_b53_dev);
++	if (!ret)
++		priv->b53_device = &bcm63xx_b53_dev;
++
++	return ret;
++}
++
++static void bcmenet_switch_unregister(struct bcm_enet_priv *priv)
++{
++	if (priv->b53_device)
++		platform_device_unregister(&bcm63xx_b53_dev);
++
++	priv->b53_device = NULL;
++}
++
+ /*
+  * switch mii access callbacks
+  */
+@@ -2270,29 +2308,6 @@ static int bcm_enetsw_open(struct net_de
+ 		enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i));
+ 	}
+ 
+-	/* reset mib */
+-	val = enetsw_readb(priv, ENETSW_GMCR_REG);
+-	val |= ENETSW_GMCR_RST_MIB_MASK;
+-	enetsw_writeb(priv, val, ENETSW_GMCR_REG);
+-	mdelay(1);
+-	val &= ~ENETSW_GMCR_RST_MIB_MASK;
+-	enetsw_writeb(priv, val, ENETSW_GMCR_REG);
+-	mdelay(1);
+-
+-	/* force CPU port state */
+-	val = enetsw_readb(priv, ENETSW_IMPOV_REG);
+-	val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK;
+-	enetsw_writeb(priv, val, ENETSW_IMPOV_REG);
+-
+-	/* enable switch forward engine */
+-	val = enetsw_readb(priv, ENETSW_SWMODE_REG);
+-	val |= ENETSW_SWMODE_FWD_EN_MASK;
+-	enetsw_writeb(priv, val, ENETSW_SWMODE_REG);
+-
+-	/* enable jumbo on all ports */
+-	enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG);
+-	enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG);
+-
+ 	/* initialize flow control buffer allocation */
+ 	enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
+ 			ENETDMA_BUFALLOC_REG(priv->rx_chan));
+@@ -2760,6 +2775,9 @@ static int bcm_enetsw_probe(struct platf
+ 	struct bcm63xx_enetsw_platform_data *pd;
+ 	struct resource *res_mem;
+ 	int ret, irq_rx, irq_tx;
++	unsigned i, num_ports = 0;
++	u16 port_mask = BIT(8);
++	u8 val;
+ 
+ 	/* stop if shared driver failed, assume driver->probe will be
+ 	 * called in the same order we register devices (correct ?) */
+@@ -2847,6 +2865,43 @@ static int bcm_enetsw_probe(struct platf
+ 	priv->pdev = pdev;
+ 	priv->net_dev = dev;
+ 
++	/* reset mib */
++	val = enetsw_readb(priv, ENETSW_GMCR_REG);
++	val |= ENETSW_GMCR_RST_MIB_MASK;
++	enetsw_writeb(priv, val, ENETSW_GMCR_REG);
++	mdelay(1);
++	val &= ~ENETSW_GMCR_RST_MIB_MASK;
++	enetsw_writeb(priv, val, ENETSW_GMCR_REG);
++	mdelay(1);
++
++	/* force CPU port state */
++	val = enetsw_readb(priv, ENETSW_IMPOV_REG);
++	val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK;
++	enetsw_writeb(priv, val, ENETSW_IMPOV_REG);
++
++	/* enable switch forward engine */
++	val = enetsw_readb(priv, ENETSW_SWMODE_REG);
++	val |= ENETSW_SWMODE_FWD_EN_MASK;
++	enetsw_writeb(priv, val, ENETSW_SWMODE_REG);
++
++	/* enable jumbo on all ports */
++	enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG);
++	enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG);
++
++	for (i = 0; i < priv->num_ports; i++) {
++		struct bcm63xx_enetsw_port *port = &priv->used_ports[i];
++
++		if (!port->used)
++			continue;
++
++		num_ports++;
++		port_mask |= BIT(i);
++	}
++
++	/* only register if there is more than one external port */
++	if (num_ports > 1)
++		bcmenet_switch_register(priv, port_mask);
++
+ 	return 0;
+ 
+ out_put_clk:
+@@ -2877,6 +2932,9 @@ static int bcm_enetsw_remove(struct plat
+ 	priv = netdev_priv(dev);
+ 	unregister_netdev(dev);
+ 
++	/* remove switch */
++	bcmenet_switch_unregister(priv);
++
+ 	/* release device resources */
+ 	iounmap(priv->base);
+ 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);

target/linux/brcm63xx/patches-3.8/500-board-D4PW.patch

@@ -0,0 +1,67 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -520,6 +520,56 @@ static struct board_info __initdata boar
+ 
+ 	.has_ohci0 = 1,
+ };
++
++static struct board_info __initdata board_96348_D4PW = {
++	.name				= "D-4P-W",
++	.expected_cpu_id		= 0x6348,
++
++	.has_enet1			= 1,
++	.has_pci			= 1,
++	.has_uart0 			= 1,
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.leds = {
++		{
++			.name		= "D-4P-W:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++		},
++		{
++			.name		= "D-4P-W::status",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{
++			.name		= "D-4P-W:green:internet",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "D-4P-W:red:internet",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 7,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -694,6 +744,7 @@ static const struct board_info __initcon
+ 	&board_DV201AMR,
+ 	&board_96348gw_a,
+ 	&board_rta1025w_16,
++	&board_96348_D4PW,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358

target/linux/brcm63xx/patches-3.8/501-board-NB4.patch

@@ -0,0 +1,650 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -15,6 +15,8 @@
+ #include <linux/gpio_keys.h>
+ #include <linux/input.h>
+ #include <linux/spi/spi.h>
++#include <linux/spi/spi_gpio.h>
++#include <linux/spi/74x164.h>
+ #include <asm/addrspace.h>
+ #include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+@@ -46,6 +48,12 @@
+ #define CFE_OFFSET_64K			0x10000
+ #define CFE_OFFSET_128K			0x20000
+ 
++#define NB4_PID_OFFSET		0xff80
++#define NB4_74X164_GPIO_BASE	64
++#define NB4_SPI_GPIO_MOSI	7
++#define NB4_SPI_GPIO_CLK	6
++#define NB4_74HC64_GPIO(X)	(NB4_74X164_GPIO_BASE + (X))
++
+ static struct board_info board;
+ 
+ /*
+@@ -719,6 +727,596 @@ static struct board_info __initdata boar
+ 
+ 	.has_ohci0			= 1,
+ };
++
++struct spi_gpio_platform_data nb4_spi_gpio_data = {
++	.sck		= NB4_SPI_GPIO_CLK,
++	.mosi		= NB4_SPI_GPIO_MOSI,
++	.miso		= SPI_GPIO_NO_MISO,
++	.num_chipselect	= 1,
++};
++
++
++static struct platform_device nb4_spi_gpio = {
++	.name = "spi_gpio",
++	.id   = 1,
++	.dev = {
++		.platform_data = &nb4_spi_gpio_data,
++	},
++};
++
++static struct platform_device * __initdata nb4_devices[] = {
++	&nb4_spi_gpio,
++};
++
++const struct gen_74x164_chip_platform_data nb4_74x164_platform_data = {
++	.base = NB4_74X164_GPIO_BASE
++};
++
++static struct spi_board_info nb4_spi_devices[] = {
++	{
++		.modalias = "74x164",
++		.max_speed_hz = 781000,
++		.bus_num = 1,
++		.controller_data = (void *) SPI_GPIO_NO_CHIPSELECT,
++		.mode = SPI_MODE_0,
++		.platform_data = &nb4_74x164_platform_data
++	}
++};
++
++static struct board_info __initdata board_nb4_ser_r0 = {
++	.name				= "NB4-SER-r0",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "NB4-SER-r0:white:adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r0:white:traffic",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r0:white:tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r0:white:tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r0:white:wifi",
++			.gpio		= 15,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r0:white:alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r0:red:service",
++			.gpio		= 29,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r0:green:service",
++			.gpio		= 30,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r0:blue:service",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "service",
++			.gpio		= 27,
++			.type		= EV_KEY,
++			.code		= BTN_0,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "clip",
++			.gpio		= 31,
++			.type		= EV_KEY,
++			.code		= BTN_1,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
++
++static struct board_info __initdata board_nb4_ser_r1 = {
++	.name				= "NB4-SER-r1",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "NB4-SER-r1:white:adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r1:white:traffic",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r1:white:tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r1:white:tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r1:white:wifi",
++			.gpio		= 15,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r1:white:alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r1:red:service",
++			.gpio		= 29,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r1:green:service",
++			.gpio		= 30,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r1:blue:service",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "service",
++			.gpio		= 27,
++			.type		= EV_KEY,
++			.code		= BTN_0,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "clip",
++			.gpio		= 31,
++			.type		= EV_KEY,
++			.code		= BTN_1,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
++
++static struct board_info __initdata board_nb4_ser_r2 = {
++	.name				= "NB4-SER-r2",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "NB4-SER-r2:white:adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r2:white:traffic",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r2:white:tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r2:white:tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r2:white:wifi",
++			.gpio		= 15,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r2:white:alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r2:red:service",
++			.gpio		= 29,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r2:green:service",
++			.gpio		= 30,
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-SER-r2:blue:service",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "service",
++			.gpio		= 27,
++			.type		= EV_KEY,
++			.code		= BTN_0,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "clip",
++			.gpio		= 31,
++			.type		= EV_KEY,
++			.code		= BTN_1,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
++
++static struct board_info __initdata board_nb4_fxc_r1 = {
++	.name				= "NB4-FXC-r1",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "NB4-FXC-r1:white:adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-FXC-r1:white:traffic",
++			.gpio		= 2,
++		},
++		{
++			.name		= "NB4-FXC-r1:white:tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-FXC-r1:white:tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-FXC-r1:white:wifi",
++			.gpio		= 15,
++		},
++		{
++			.name		= "NB4-FXC-r1:white:alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-FXC-r1:red:service",
++			.gpio		= 29,
++		},
++		{
++			.name		= "NB4-FXC-r1:green:service",
++			.gpio		= 30,
++		},
++		{
++			.name		= "NB4-FXC-r1:blue:service",
++			.gpio		= 4,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "service",
++			.gpio		= 27,
++			.type		= EV_KEY,
++			.code		= BTN_0,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "clip",
++			.gpio		= 31,
++			.type		= EV_KEY,
++			.code		= BTN_1,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
++
++static struct board_info __initdata board_nb4_fxc_r2 = {
++	.name				= "NB4-FXC-r2",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "NB4-FXC-r2:white:adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-FXC-r2:white:traffic",
++			.gpio		= 2,
++		},
++		{
++			.name		= "NB4-FXC-r2:white:tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-FXC-r2:white:tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-FXC-r2:white:wifi",
++			.gpio		= 15,
++		},
++		{
++			.name		= "NB4-FXC-r2:white:alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "NB4-FXC-r2:red:service",
++			.gpio		= 29,
++		},
++		{
++			.name		= "NB4-FXC-r2:green:service",
++			.gpio		= 30,
++		},
++		{
++			.name		= "NB4-FXC-r2:blue:service",
++			.gpio		= 4,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "service",
++			.gpio		= 27,
++			.type		= EV_KEY,
++			.code		= BTN_0,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "clip",
++			.gpio		= 31,
++			.type		= EV_KEY,
++			.code		= BTN_1,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
+ #endif
+ 
+ /*
+@@ -752,6 +1350,11 @@ static const struct board_info __initcon
+ 	&board_96358vw2,
+ 	&board_AGPFS0,
+ 	&board_DWVS0,
++	&board_nb4_ser_r0,
++	&board_nb4_ser_r1,
++	&board_nb4_ser_r2,
++	&board_nb4_fxc_r1,
++	&board_nb4_fxc_r2,
+ #endif
+ };
+ 
+@@ -806,6 +1409,16 @@ static void __init boardid_fixup(u8 *boo
+ 	struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K);
+ 	char *board_name = (char *)bcm63xx_nvram_get_name();
+ 
++	if (BCMCPU_IS_6358() && (!strcmp(board_name, "96358VW"))) {
++		u8 *p = boot_addr + NB4_PID_OFFSET;
++
++		/* Extract nb4 PID */
++		if (!memcmp(p, "NB4-", 4)) {
++			memcpy(board_name, p, sizeof("NB4-XXX-rX"));
++			return;
++		}
++	}
++
+ 	/* check if bcm_tag is at 64k offset */
+ 	if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) {
+ 		/* else try 128k */

target/linux/brcm63xx/patches-3.8/502-board-96338W2_E7T.patch

@@ -0,0 +1,51 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -191,6 +191,40 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_96338w2_e7t = {
++	.name				= "96338W2_E7T",
++	.expected_cpu_id		= 0x6338,
++
++	.has_enet0			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++		.leds = {
++		{
++			.name		= "96338W2_E7T:green:ppp",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "96338W2_E7T:green:ppp-fail",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "96338W2_E7T:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -1329,6 +1363,7 @@ static const struct board_info __initcon
+ #ifdef CONFIG_BCM63XX_CPU_6338
+ 	&board_96338gw,
+ 	&board_96338w,
++	&board_96338w2_e7t,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_6345
+ 	&board_96345gw2,

target/linux/brcm63xx/patches-3.8/503-board-CPVA642.patch

@@ -0,0 +1,109 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -718,6 +718,98 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++static struct board_info __initdata board_CPVA642 = {
++	.name                           = "CPVA642",
++	.expected_cpu_id                = 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet1                      = 1,
++	.has_pci                        = 1,
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100        = 1,
++		.force_duplex_full      = 1,
++ 	},
++
++	.has_ohci0 = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "CPVA642:red:power",
++			.gpio		= 14,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CPVA642:green:power",
++			.gpio		= 11,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "CPVA642:red:wifi",
++			.gpio		= 6,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CPVA642:green:wifi",
++			.gpio		= 28,
++			.active_low	= 0,
++		},
++		{
++			.name		= "CPVA642:red:link",
++			.gpio		= 9,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CPVA642:green:link",
++			.gpio		= 10,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CPVA642:green:ether",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CPVA642:green:phone1",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CPVA642:green:phone2",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CPVA642:green:usb",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++    },
++
++	.buttons = {
++		{
++			.desc           = "reset",
++			.gpio           = 36,
++			.active_low     = 1,
++			.type           = EV_KEY,
++			.code           = KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
++
+ static struct board_info __initdata board_AGPFS0 = {
+ 	.name                           = "AGPF-S0",
+ 	.expected_cpu_id                = 0x6358,
+@@ -1384,6 +1476,7 @@ static const struct board_info __initcon
+ 	&board_96358vw,
+ 	&board_96358vw2,
+ 	&board_AGPFS0,
++	&board_CPVA642,
+ 	&board_DWVS0,
+ 	&board_nb4_ser_r0,
+ 	&board_nb4_ser_r1,

target/linux/brcm63xx/patches-3.8/504-board_dsl_274xb_rev_c.patch

@@ -0,0 +1,72 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -854,6 +854,61 @@ static struct board_info __initdata boar
+ 	.has_ohci0			= 1,
+ };
+ 
++/* D-Link DSL-274xB revison C2/C3 */
++static struct board_info __initdata board_dsl_274xb_rev_c = {
++	.name				= "AW4139",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.leds = {
++		{
++			.name		= "dsl-274xb:green:power",
++			.gpio		= 5,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "dsl-274xb:red:power",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "dsl-274xb:green:adsl",
++			.gpio		= 9,
++			.active_low	= 1,
++		},
++		{
++			.name		= "dsl-274xb:green:internet",
++			.gpio		= 2,
++		},
++		{
++			.name		= "dsl-274xb:red:internet",
++			.gpio		= 10,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
+ struct spi_gpio_platform_data nb4_spi_gpio_data = {
+ 	.sck		= NB4_SPI_GPIO_CLK,
+ 	.mosi		= NB4_SPI_GPIO_MOSI,
+@@ -1478,6 +1533,7 @@ static const struct board_info __initcon
+ 	&board_AGPFS0,
+ 	&board_CPVA642,
+ 	&board_DWVS0,
++	&board_dsl_274xb_rev_c,
+ 	&board_nb4_ser_r0,
+ 	&board_nb4_ser_r1,
+ 	&board_nb4_ser_r2,

target/linux/brcm63xx/patches-3.8/505-board_spw500v.patch

@@ -0,0 +1,78 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -612,6 +612,67 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_spw500v = {
++	.name				= "SPW500V",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.has_dsp			= 1,
++	.dsp = {
++		.gpio_rst		= 6,
++		.gpio_int		= 34,
++		.ext_irq		= 2,
++		.cs			= 2,
++	},
++
++	.leds = {
++		{
++			.name		= "SPW500V:red:power",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++		{
++			.name		= "SPW500V:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "SPW500V:green:ppp",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{	.name		= "SPW500V:green:pstn",
++			.gpio		= 28,
++			.active_low	= 1,
++		},
++		{
++			.name		= "SPW500V:green:voip",
++			.gpio		= 32,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 33,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -1525,6 +1586,7 @@ static const struct board_info __initcon
+ 	&board_96348gw_a,
+ 	&board_rta1025w_16,
+ 	&board_96348_D4PW,
++	&board_spw500v,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358

target/linux/brcm63xx/patches-3.8/506-board_gw6200_gw6000.patch

@@ -0,0 +1,124 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -479,6 +479,112 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++static struct board_info __initdata board_gw6200 = {
++	.name				= "GW6200",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0 = 1,
++
++	.has_dsp			= 1,
++		.dsp = {
++		.gpio_rst		= 8, /* FIXME: What is real GPIO here? */
++		.gpio_int		= 34,
++		.ext_irq		= 2,
++		.cs			= 2,
++	},
++
++	.leds = {
++		{
++			.name		= "GW6200:green:line1",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "GW6200:green:line2",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "GW6200:green:line3",
++			.gpio		= 6,
++			.active_low	= 1,
++		},
++		{
++			.name		= "GW6200:green:tel",
++			.gpio		= 7,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 36,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
++static struct board_info __initdata board_gw6000 = {
++	.name				= "GW6000",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0 = 1,
++
++	.has_dsp			= 1,
++	.dsp = {
++		.gpio_rst		= 6,
++		.gpio_int		= 34,
++		.ext_irq		= 2,
++		.cs			= 2,
++	},
++
++	/* GW6000 has no GPIO-controlled leds */
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 36,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
++
++
+ static struct board_info __initdata board_FAST2404 = {
+ 	.name				= "F@ST2404",
+ 	.expected_cpu_id		= 0x6348,
+@@ -1579,6 +1685,8 @@ static const struct board_info __initcon
+ #ifdef CONFIG_BCM63XX_CPU_6348
+ 	&board_96348r,
+ 	&board_96348gw,
++	&board_gw6000,
++	&board_gw6200,
+ 	&board_96348gw_10,
+ 	&board_96348gw_11,
+ 	&board_FAST2404,

target/linux/brcm63xx/patches-3.8/507-board-MAGIC.patch

@@ -0,0 +1,89 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -779,6 +779,78 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_96348sv = {
++	.name				= "MAGIC",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++	.enet1 = {
++		/* it has BP_ENET_EXTERNAL_PHY */
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0			= 1,
++	.has_pccard			= 1,
++	.has_ehci0			= 1,
++
++	.has_dsp			= 1,
++	.dsp = {
++		.gpio_rst		= 25,
++		.gpio_int		= 34,
++		.cs			= 2,
++		.ext_irq		= 2,
++	},
++
++	.leds = {
++		{
++			.name		= "MAGIC:green:voip",
++			.gpio		= 22,
++			.active_low	= 1,
++		},
++		{
++			.name		= "MAGIC:green:adsl",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "MAGIC:green:wifi",
++			.gpio		= 28,
++		},
++		{
++			.name		= "MAGIC:green:usb",
++			.gpio		= 35,
++			.active_low	= 1,
++		},
++		{
++			.name		= "MAGIC:green:hpna",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "MAGIC:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "MAGIC:green:stop",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -1695,6 +1767,7 @@ static const struct board_info __initcon
+ 	&board_rta1025w_16,
+ 	&board_96348_D4PW,
+ 	&board_spw500v,
++	&board_96348sv,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358

target/linux/brcm63xx/patches-3.8/508-board_hw553.patch

@@ -0,0 +1,93 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1737,6 +1737,82 @@ static struct board_info __initdata boar
+ 	.spis = nb4_spi_devices,
+ 	.num_spis = ARRAY_SIZE(nb4_spi_devices),
+ };
++
++static struct board_info __initdata board_HW553 = {
++	.name                           = "HW553",
++	.expected_cpu_id                = 0x6358,
++
++	.has_uart0			= 1,
++
++	.has_enet0                      = 1,
++	.has_enet1                      = 1,
++	.has_pci                        = 1,
++
++	.enet0 = {
++		.has_phy                = 1,
++		.use_internal_phy       = 1,
++	},
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100        = 1,
++		.force_duplex_full      = 1,
++	},
++
++	.has_ohci0 = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "HW553:red:lan",
++			.gpio		= 34,
++			.active_low	= 1,
++		},
++		{
++			.name		= "HW553:blue:lan",
++			.gpio		= 35,
++			.active_low	= 1,
++		},
++		{
++			.name		= "HW553:red:adsl",
++			.gpio		= 22,
++			.active_low	= 1,
++		},
++		{
++			.name		= "HW553:blue:adsl",
++			.gpio		= 23,
++			.active_low	= 1,
++		},
++		{
++			.name		= "HW553:red:power",
++			.gpio		= 5,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++
++		{
++			.name		= "HW553:blue:power",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "HW553:red:wifi",
++			.gpio		= 25,
++			.active_low	= 1,
++		},
++		{
++			.name		= "HW553:red:internetkey",
++			.gpio		= 12,
++			.active_low	= 1,
++		},
++		{
++			.name		= "HW553:blue:internetkey",
++			.gpio		= 13,
++			.active_low	= 1,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -1782,6 +1858,7 @@ static const struct board_info __initcon
+ 	&board_nb4_ser_r2,
+ 	&board_nb4_fxc_r1,
+ 	&board_nb4_fxc_r2,
++	&board_HW553,
+ #endif
+ };
+ 

target/linux/brcm63xx/patches-3.8/509-board_rta1320_16m.patch

@@ -0,0 +1,56 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -225,6 +225,45 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_rta1320_16m = {
++	.name				= "RTA1320_16M",
++	.expected_cpu_id		= 0x6338,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++		.leds = {
++		{
++			.name		= "RTA1320_16M:green:adsl",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{
++			.name		= "RTA1320_16M:green:ppp",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "RTA1320_16M:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "RTA1320_16M:green:stop",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -1826,6 +1865,7 @@ static const struct board_info __initcon
+ 	&board_96338gw,
+ 	&board_96338w,
+ 	&board_96338w2_e7t,
++	&board_rta1320_16m,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_6345
+ 	&board_96345gw2,

target/linux/brcm63xx/patches-3.8/510-board_spw303v.patch

@@ -0,0 +1,83 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1852,6 +1852,72 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++ /* T-Home Speedport W 303V Typ B */
++static struct board_info __initdata board_spw303v = {
++	.name			= "96358-502V",
++	.expected_cpu_id	= 0x6358,
++
++	.has_uart0		= 1,
++	.has_enet0		= 1,
++	.has_pci		= 1,
++
++	.enet0 = {
++		.has_phy 		= 1,
++		.use_internal_phy 	= 1,
++	},
++
++	.leds = {
++		{
++			.name		= "spw303v:green:power+adsl",
++			.gpio		= 22,
++			.active_low 	= 1,
++		},
++		{
++			.name		= "spw303v:red:power+adsl",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "spw303v:green:ppp",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "spw303v:green:ses",
++			.gpio		= 0,
++			.active_low	= 1,
++		},
++		{
++			.name		= "spw303v:green:voip",
++			.gpio		= 27,
++			.active_low	= 1,
++		},
++		{
++			.name		= "spw303v:green:pots",
++			.gpio		= 31,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 11,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "ses",
++			.gpio		= 37,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	}
++};
+ #endif
+ 
+ /*
+@@ -1899,6 +1965,7 @@ static const struct board_info __initcon
+ 	&board_nb4_fxc_r1,
+ 	&board_nb4_fxc_r2,
+ 	&board_HW553,
++	&board_spw303v,
+ #endif
+ };
+ 

target/linux/brcm63xx/patches-3.8/511-board_V2500V.patch

@@ -0,0 +1,123 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -890,6 +890,65 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_V2500V_BB = {
++	.name				= "V2500V_BB",
++        .expected_cpu_id                = 0x6348,
++
++        .has_uart0                      = 1,
++        .has_enet0                      = 1,
++        .has_enet1                      = 1,
++        .has_pci                        = 1,
++
++        .enet0 = {
++                .has_phy                = 1,
++                .use_internal_phy       = 1,
++        },
++        .enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++                .force_speed_100        = 1,
++                .force_duplex_full      = 1,
++	},
++
++	.leds =	{
++		{
++			.name		= "V2500V_BB:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "V2500V_BB:red:power",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++		{
++			.name		= "V2500V_BB:green:adsl",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{	.name		= "V2500V_BB:green:ppp",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{
++			.name		= "V2500V_BB:green:wireless",
++			.gpio		= 6,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 31,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -1950,6 +2009,7 @@ static const struct board_info __initcon
+ 	&board_96348_D4PW,
+ 	&board_spw500v,
+ 	&board_96348sv,
++	&board_V2500V_BB,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358
+@@ -2070,6 +2130,22 @@ void __init board_prom_init(void)
+ 		val &= MPI_CSBASE_BASE_MASK;
+ 	}
+ 	boot_addr = (u8 *)KSEG1ADDR(val);
++	printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
++
++	/* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
++	/* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
++	/* Loading firmware from the CFE Prompt always loads to Bank 0 */
++	/* Do an early check of CFE and then select bank 0 */
++
++	if (boot_addr == (u8 *)0xbf800000) {
++		u8 *tmp_boot_addr = (u8*)0xbfc00000;
++
++		if (!bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET) &&
++		    !strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
++			printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
++			boot_addr = tmp_boot_addr;
++		}
++	}
+ 
+ 	/* dump cfe version */
+ 	cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -19,6 +19,7 @@
+ #include <linux/spi/spi.h>
+ #include <linux/spi/flash.h>
+ 
++#include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+ #include <bcm63xx_dev_flash.h>
+ #include <bcm63xx_dev_hsspi.h>
+@@ -162,6 +163,13 @@ int __init bcm63xx_flash_register(int nu
+ 		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+ 		val &= MPI_CSBASE_BASE_MASK;
+ 
++		/* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
++		/* Loading from CFE always uses Bank 0 */
++		if (!strcmp(board_get_name(), "V2500V_BB")) {
++			pr_info("V2500V: Start in Bank 0\n");
++			val = val + 0x400000; // Select Bank 0 start address
++		}
++
+ 		mtd_resources[0].start = val;
+ 		mtd_resources[0].end = 0x1FFFFFFF;
+ 

target/linux/brcm63xx/patches-3.8/512-board_BTV2110.patch

@@ -0,0 +1,75 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -450,6 +450,64 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++
++/* BT Voyager 2110 */
++static struct board_info __initdata board_V2110 = {
++	.name				= "V2110",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.leds = {
++		{
++			.name           = "V2110:green:power",
++			.gpio           = 0,
++			.active_low     = 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name           = "V2110:red:power",
++			.gpio           = 1,
++			.active_low     = 1,
++		},
++		{
++			.name           = "V2110:green:adsl",
++			.gpio           = 2,
++			.active_low     = 1,
++		},
++		{       .name           = "V2110:green:ppp",
++			.gpio           = 3,
++			.active_low     = 1,
++		},
++		{
++			.name           = "V2110:green:wireless",
++			.gpio           = 6,
++			.active_low     = 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 33,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
++
+ static struct board_info __initdata board_96348gw = {
+ 	.name				= "96348GW",
+ 	.expected_cpu_id		= 0x6348,
+@@ -2010,6 +2068,7 @@ static const struct board_info __initcon
+ 	&board_spw500v,
+ 	&board_96348sv,
+ 	&board_V2500V_BB,
++	&board_V2110,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358

target/linux/brcm63xx/patches-3.8/513-board_livebox.patch

@@ -0,0 +1,389 @@
+--- a/arch/mips/bcm63xx/boards/Kconfig
++++ b/arch/mips/bcm63xx/boards/Kconfig
+@@ -8,4 +8,10 @@ config BOARD_BCM963XX
+ 	select SSB
+        help
+ 
++config BOARD_LIVEBOX
++	bool "Inventel Livebox(es) boards"
++	select SSB
++	help
++	 Inventel Livebox boards using the RedBoot bootloader.
++
+ endchoice
+--- a/arch/mips/bcm63xx/boards/Makefile
++++ b/arch/mips/bcm63xx/boards/Makefile
+@@ -1 +1,2 @@
+ obj-$(CONFIG_BOARD_BCM963XX)		+= board_bcm963xx.o
++obj-$(CONFIG_BOARD_LIVEBOX)		+= board_livebox.o
+--- /dev/null
++++ b/arch/mips/bcm63xx/boards/board_livebox.c
+@@ -0,0 +1,368 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
++ */
++
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/string.h>
++#include <linux/platform_device.h>
++#include <linux/mtd/mtd.h>
++#include <linux/mtd/partitions.h>
++#include <linux/mtd/physmap.h>
++#include <linux/ssb/ssb.h>
++#include <linux/gpio_keys.h>
++#include <linux/input.h>
++#include <linux/spi/spi.h>
++#include <asm/addrspace.h>
++#include <bcm63xx_board.h>
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_dev_uart.h>
++#include <bcm63xx_regs.h>
++#include <bcm63xx_io.h>
++#include <bcm63xx_dev_pci.h>
++#include <bcm63xx_dev_enet.h>
++#include <bcm63xx_dev_dsp.h>
++#include <bcm63xx_dev_pcmcia.h>
++#include <bcm63xx_dev_usb_ohci.h>
++#include <bcm63xx_dev_usb_ehci.h>
++#include <bcm63xx_dev_spi.h>
++#include <board_bcm963xx.h>
++
++#define PFX	"board_livebox: "
++
++#define LIVEBOX_KEYS_POLL_INTERVAL	20
++#define LIVEBOX_KEYS_DEBOUNCE_INTERVAL	(LIVEBOX_KEYS_POLL_INTERVAL * 3)
++
++static unsigned int mac_addr_used = 0;
++static struct board_info board;
++
++/*
++ * known 6348 boards
++ */
++#ifdef CONFIG_BCM63XX_CPU_6348
++static struct board_info __initdata board_livebox_blue5g = {
++	.name				= "Livebox-blue-5g",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		  .has_phy		= 1,
++		  .phy_id 		= 31,
++	},
++
++	.has_ohci0			= 1,
++	.has_pccard			= 1,
++
++	.has_dsp			= 0, /*TODO some Liveboxes have dsp*/
++	.dsp = {
++		.gpio_rst		= 6, /*FIXME eth1 shares gpio6 with dsp?*/
++		.gpio_int		= 35,
++		.cs			= 2,
++		.ext_irq		= 2,
++	},
++
++	.leds = {
++		{
++			.name		= "Livebox-blue-5g::adsl-fail",
++			.gpio		= 0,
++			.active_low	= 0,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "Livebox-blue-5g::adsl",
++			.gpio		= 1,
++		},
++		{
++			.name		= "Livebox-blue-5g::traffic",
++			.gpio		= 2,
++		},
++		{
++			.name		= "Livebox-blue-5g::phone",
++			.gpio		= 3,
++		},
++		{
++			.name		= "Livebox-blue-5g::wifi",
++			.gpio		= 4,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "BTN_1",
++			.gpio		= 36,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= BTN_1,
++			.debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "BTN_2",
++			.gpio		= 7,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= BTN_2,
++			.debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL,
++		},
++
++	},
++};
++#endif
++
++/*
++ * all boards
++ */
++static const struct board_info __initdata *bcm963xx_boards[] = {
++#ifdef CONFIG_BCM63XX_CPU_6348
++	&board_livebox_blue5g
++#endif
++};
++/*
++ * return board name for /proc/cpuinfo
++ */
++const char *board_get_name(void)
++{
++	return board.name;
++}
++
++/*
++ * register & return a new board mac address
++ */
++static int board_get_mac_address(u8 *mac)
++{
++	u8 *p;
++	int count;
++
++	memcpy(mac, (u8 *)0xBEBFF377, ETH_ALEN);
++
++	p = mac + ETH_ALEN - 1;
++	count = mac_addr_used;
++
++	while (count--) {
++		do {
++			(*p)++;
++			if (*p != 0)
++				break;
++			p--;
++		} while (p != mac);
++	}
++
++	if (p == mac) {
++		printk(KERN_ERR PFX "unable to fetch mac address\n");
++		return -ENODEV;
++	}
++        mac_addr_used++;
++
++	return 0;
++}
++
++/*
++ * early init callback
++ */
++#define LIVEBOX_GPIO_DETECT_MASK	0x000000ff
++#define LIVEBOX_BOOT_ADDR		0x1e400000
++
++#define LIVEBOX_HW_BLUE5G_9		0x90
++
++void __init board_prom_init(void)
++{
++	u32 val;
++	u8 hw_version;
++
++	/* Get hardware version */
++	val = bcm_gpio_readl(GPIO_CTL_LO_REG);
++	val &= ~LIVEBOX_GPIO_DETECT_MASK;
++	bcm_gpio_writel(val, GPIO_CTL_LO_REG);
++
++	hw_version = bcm_gpio_readl(GPIO_DATA_LO_REG) & LIVEBOX_GPIO_DETECT_MASK;
++	switch (hw_version) {
++	case LIVEBOX_HW_BLUE5G_9:
++		printk(KERN_INFO PFX "Livebox BLUE5G.9\n");
++		memcpy(&board, bcm963xx_boards[0], sizeof(board));
++		break;
++	default:
++		printk(KERN_INFO PFX "Unknown livebox version: %02x\n", hw_version);
++		break;
++	}
++
++	/* use default livebox configuration */
++	memcpy(&board, bcm963xx_boards[0], sizeof(board));
++
++	/* setup pin multiplexing depending on board enabled device,
++	 * this has to be done this early since PCI init is done
++	 * inside arch_initcall */
++	val = 0;
++
++#ifdef CONFIG_PCI
++	if (board.has_pci) {
++		if (BCMCPU_IS_6348())
++			val |= GPIO_MODE_6348_G2_PCI;
++	}
++#endif
++	if (board.has_pccard) {
++		if (BCMCPU_IS_6348())
++			val |= GPIO_MODE_6348_G1_MII_PCCARD;
++	}
++
++	if (board.has_enet0 && !board.enet0.use_internal_phy) {
++		if (BCMCPU_IS_6348())
++			val |= GPIO_MODE_6348_G3_EXT_MII |
++				GPIO_MODE_6348_G0_EXT_MII;
++	}
++
++	if (board.has_enet1 && !board.enet1.use_internal_phy) {
++		if (BCMCPU_IS_6348())
++			val |= GPIO_MODE_6348_G3_EXT_MII |
++				GPIO_MODE_6348_G0_EXT_MII;
++			printk(KERN_INFO PFX "resetting gpio6 for eth1...\n");
++			gpio_request(6, "dsp_eth_rst");
++			gpio_direction_output(6, 0);
++			gpio_set_value(6, 1);
++	}
++
++	bcm_gpio_writel(val, GPIO_MODE_REG);
++}
++
++/*
++ * second stage init callback, good time to panic if we couldn't
++ * identify on which board we're running since early printk is working
++ */
++void __init board_setup(void)
++{
++	if (!board.name[0])
++		panic("unable to detect bcm963xx board");
++	printk(KERN_INFO PFX "board name: %s\n", board.name);
++
++	/* make sure we're running on expected cpu */
++	if (bcm63xx_get_cpu_id() != board.expected_cpu_id)
++		panic("unexpected CPU for bcm963xx board");
++}
++
++static struct physmap_flash_data flash_data = {
++	.width			= 2,
++};
++
++static struct resource mtd_resources[] = {
++	{
++		.start          = 0,    /* filled at runtime */
++		.end            = 0,    /* filled at runtime */
++		.flags          = IORESOURCE_MEM,
++	}
++};
++
++static struct platform_device mtd_dev = {
++	.name			= "physmap-flash",
++	.resource		= mtd_resources,
++	.num_resources		= ARRAY_SIZE(mtd_resources),
++	.dev			= {
++		.platform_data	= &flash_data,
++	},
++};
++
++static struct gpio_led_platform_data bcm63xx_led_data;
++
++static struct platform_device bcm63xx_gpio_leds = {
++	.name			= "leds-gpio",
++	.id			= 0,
++	.dev.platform_data	= &bcm63xx_led_data,
++};
++
++static struct gpio_keys_platform_data bcm63xx_gpio_keys_data = {
++	.poll_interval  = LIVEBOX_KEYS_POLL_INTERVAL,
++};
++
++static struct platform_device bcm63xx_gpio_keys_device = {
++	.name		= "gpio-keys-polled",
++	.id		= 0,
++	.dev.platform_data = &bcm63xx_gpio_keys_data,
++};
++
++/*
++ * third stage init callback, register all board devices.
++ */
++int __init board_register_devices(void)
++{
++	u32 val;
++	int led_count = 0;
++	int button_count = 0;
++
++	if (board.has_uart0)
++		bcm63xx_uart_register(0);
++
++	if (board.has_uart1)
++		bcm63xx_uart_register(1);
++
++	if (board.has_pccard)
++		bcm63xx_pcmcia_register();
++
++	if (board.has_enet0 &&
++	    !board_get_mac_address(board.enet0.mac_addr))
++		bcm63xx_enet_register(0, &board.enet0);
++
++	if (board.has_enet1 &&
++	    !board_get_mac_address(board.enet1.mac_addr))
++		bcm63xx_enet_register(1, &board.enet1);
++
++	if (board.has_ehci0)
++		bcm63xx_ehci_register();
++
++	if (board.has_ohci0)
++		bcm63xx_ohci_register();
++
++	if (board.has_dsp)
++		bcm63xx_dsp_register(&board.dsp);
++
++	bcm63xx_spi_register();
++
++	if (board.num_devs)
++		platform_add_devices(board.devs, board.num_devs);
++
++	if (board.num_spis)
++		spi_register_board_info(board.spis, board.num_spis);
++
++
++	/* read base address of boot chip select (0) */
++	val = bcm_mpi_readl(MPI_CSBASE_REG(0));
++	val &= MPI_CSBASE_BASE_MASK;
++	if (val != LIVEBOX_BOOT_ADDR)
++		printk(KERN_NOTICE PFX "flash address is: 0x%08x, forcing to: 0x%08x\n",
++			val, LIVEBOX_BOOT_ADDR);
++	mtd_resources[0].start = LIVEBOX_BOOT_ADDR;
++	mtd_resources[0].end = 0x1ebfffff;
++
++	platform_device_register(&mtd_dev);
++
++	/* count number of LEDs defined by this device */
++	while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name)
++		led_count++;
++
++	bcm63xx_led_data.num_leds = led_count;
++	bcm63xx_led_data.leds = board.leds;
++
++	platform_device_register(&bcm63xx_gpio_leds);
++
++	/* count number of BUTTONs defined by this device */
++	while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc)
++		button_count++;
++
++	if (button_count) {
++		bcm63xx_gpio_keys_data.nbuttons = button_count;
++		bcm63xx_gpio_keys_data.buttons = board.buttons;
++
++		platform_device_register(&bcm63xx_gpio_keys_device);
++	}
++
++	return 0;
++}

target/linux/brcm63xx/patches-3.8/514-board_ct536_ct5621.patch

@@ -0,0 +1,62 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -508,6 +508,51 @@ static struct board_info __initdata boar
+ };
+ 
+ 
++static struct board_info __initdata board_ct536_ct5621 = {
++	.name				= "CT536_CT5621",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 0,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "CT536_CT5621:green:adsl-fail",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CT536_CT5621:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 33,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
+ static struct board_info __initdata board_96348gw = {
+ 	.name				= "96348GW",
+ 	.expected_cpu_id		= 0x6348,
+@@ -2069,6 +2114,7 @@ static const struct board_info __initcon
+ 	&board_96348sv,
+ 	&board_V2500V_BB,
+ 	&board_V2110,
++	&board_ct536_ct5621,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358

target/linux/brcm63xx/patches-3.8/515-board_DWV-S0_fixes.patch

@@ -0,0 +1,19 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1277,6 +1277,8 @@ static struct board_info __initdata boar
+ 	.name				= "DWV-S0",
+ 	.expected_cpu_id		= 0x6358,
+ 
++	.has_uart0			= 1,
++
+ 	.has_enet0			= 1,
+ 	.has_enet1			= 1,
+ 	.has_pci			= 1,
+@@ -1292,6 +1294,7 @@ static struct board_info __initdata boar
+ 	},
+ 
+ 	.has_ohci0			= 1,
++	.has_ehci0			= 1,
+ };
+ 
+ /* D-Link DSL-274xB revison C2/C3 */

target/linux/brcm63xx/patches-3.8/516-board_96348A-122.patch

@@ -0,0 +1,80 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -553,6 +553,69 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++static struct board_info __initdata board_96348A_122 = {
++	.name				= "96348A-122",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0 = 1,
++
++	.leds = {
++		{
++			.name		= "96348A-122:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "96348A-122:red:alarm",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "96348A-122:green:wps",
++			.gpio		= 6,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 33,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wlan",
++			.gpio		= 34,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_WLAN,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 35,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
+ static struct board_info __initdata board_96348gw = {
+ 	.name				= "96348GW",
+ 	.expected_cpu_id		= 0x6348,
+@@ -2118,6 +2181,7 @@ static const struct board_info __initcon
+ 	&board_V2500V_BB,
+ 	&board_V2110,
+ 	&board_ct536_ct5621,
++	&board_96348A_122,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358

target/linux/brcm63xx/patches-3.8/517-RTA1205W_16_uart_fixes.patch

@@ -0,0 +1,10 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -818,6 +818,7 @@ static struct board_info __initdata boar
+ 	.name				= "RTA1025W_16",
+ 	.expected_cpu_id		= 0x6348,
+ 
++	.has_uart0			= 1,
+ 	.has_enet0			= 1,
+ 	.has_enet1			= 1,
+ 	.has_pci			= 1,

target/linux/brcm63xx/patches-3.8/519_board_CPVA502plus.patch

@@ -0,0 +1,57 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1116,6 +1116,46 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_CPVA502plus = {
++	.name				= "CPVA502+",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.leds = {
++		{
++			.name		= "CPVA502+:green:phone",
++			.gpio		= 0,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CPVA502+:green:link",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CPVA502+:green:feth1", /* FIXME:does gpio4 enable eth1 phy? */
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++	},
++};
++
+ #endif
+ 
+ /*
+@@ -2183,6 +2223,7 @@ static const struct board_info __initcon
+ 	&board_V2110,
+ 	&board_ct536_ct5621,
+ 	&board_96348A_122,
++	&board_CPVA502plus,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358

target/linux/brcm63xx/patches-3.8/520-bcm63xx-add-support-for-96368MVWG-board.patch

@@ -0,0 +1,128 @@
+From eeacc2529942051504bc957726aa178671344421 Mon Sep 17 00:00:00 2001
+From: Maxime Bizon <mbizon@freebox.fr>
+Date: Wed, 20 Jan 2010 16:21:30 +0100
+Subject: [PATCH 32/63] bcm63xx: add support for 96368MVWG board.
+
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c          |   95 ++++++++++++++++++++
+ .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h |    2 +
+ 2 files changed, 97 insertions(+), 0 deletions(-)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -2190,6 +2190,78 @@ static struct board_info __initdata boar
+ #endif
+ 
+ /*
++ * known 6368 boards
++ */
++#ifdef CONFIG_BCM63XX_CPU_6368
++static struct board_info __initdata board_96368mvwg = {
++	.name				= "96368MVWG",
++	.expected_cpu_id		= 0x6368,
++
++	.has_uart0			= 1,
++	.has_pci			= 1,
++	.has_enetsw			= 1,
++
++	.enetsw = {
++		.used_ports = {
++			[1] = {
++				.used	= 1,
++				.phy_id	= 2,
++				.name	= "port1",
++			},
++
++			[2] = {
++				.used	= 1,
++				.phy_id	= 3,
++				.name	= "port2",
++			},
++
++			[4] = {
++				.used	= 1,
++				.phy_id	= 0x12,
++				.name	= "port0",
++			},
++
++			[5] = {
++				.used	= 1,
++				.phy_id	= 0x11,
++				.name	= "port3",
++			},
++		},
++	},
++
++	.leds = {
++		{
++			.name		= "96368MVWG:green:adsl",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "96368MVWG:green:ppp",
++			.gpio		= 5,
++		},
++		{
++			.name		= "96368MVWG:green:power",
++			.gpio		= 22,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "96368MVWG:green:wps",
++			.gpio		= 23,
++			.active_low	= 1,
++		},
++		{
++			.name		= "96368MVWG:green:ppp-fail",
++			.gpio		= 31,
++		},
++	},
++
++	.has_ohci0 = 1,
++	.has_ehci0 = 1,
++};
++#endif
++
++/*
+  * all boards
+  */
+ static const struct board_info __initconst *bcm963xx_boards[] = {
+@@ -2241,6 +2313,10 @@ static const struct board_info __initcon
+ 	&board_HW553,
+ 	&board_spw303v,
+ #endif
++
++#ifdef CONFIG_BCM63XX_CPU_6368
++	&board_96368mvwg,
++#endif
+ };
+ 
+ /*
+@@ -2412,12 +2488,25 @@ void __init board_prom_init(void)
+ 		bcm63xx_pci_enabled = 1;
+ 		if (BCMCPU_IS_6348())
+ 			val |= GPIO_MODE_6348_G2_PCI;
++
++		if (BCMCPU_IS_6368())
++			val |= GPIO_MODE_6368_PCI_REQ1 |
++				GPIO_MODE_6368_PCI_GNT1 |
++				GPIO_MODE_6368_PCI_INTB |
++				GPIO_MODE_6368_PCI_REQ0 |
++				GPIO_MODE_6368_PCI_GNT0;
+ 	}
+ #endif
+ 
+ 	if (board.has_pccard) {
+ 		if (BCMCPU_IS_6348())
+ 			val |= GPIO_MODE_6348_G1_MII_PCCARD;
++
++		if (BCMCPU_IS_6368())
++			val |= GPIO_MODE_6368_PCMCIA_CD1 |
++				GPIO_MODE_6368_PCMCIA_CD2 |
++				GPIO_MODE_6368_PCMCIA_VS1 |
++				GPIO_MODE_6368_PCMCIA_VS2;
+ 	}
+ 
+ 	if (board.has_enet0 && !board.enet0.use_internal_phy) {

target/linux/brcm63xx/patches-3.8/521-bcm63xx-add-support-for-96368MVNgr-board.patch

@@ -0,0 +1,92 @@
+From f457fc2eb9bb915b5a4d251c7c68d4694cf07b01 Mon Sep 17 00:00:00 2001
+From: Maxime Bizon <mbizon@freebox.fr>
+Date: Fri, 4 Nov 2011 12:33:48 +0100
+Subject: [PATCH 33/63] bcm63xx: add support for 96368MVNgr board.
+
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c |   67 +++++++++++++++++++++++++++++
+ 1 files changed, 67 insertions(+), 0 deletions(-)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -2259,6 +2259,72 @@ static struct board_info __initdata boar
+ 	.has_ohci0 = 1,
+ 	.has_ehci0 = 1,
+ };
++
++static struct board_info __initdata board_96368mvngr = {
++	.name				= "96368MVNgr",
++	.expected_cpu_id		= 0x6368,
++
++	.has_uart0			= 1,
++	.has_pci			= 1,
++	.has_enetsw			= 1,
++
++	.enetsw = {
++		.used_ports = {
++			[0] = {
++				.used	= 1,
++				.phy_id	= 1,
++				.name	= "port1",
++			},
++
++			[1] = {
++				.used	= 1,
++				.phy_id	= 2,
++				.name	= "port2",
++			},
++
++			[2] = {
++				.used	= 1,
++				.phy_id	= 3,
++				.name	= "port3",
++			},
++
++			[3] = {
++				.used	= 1,
++				.phy_id	= 4,
++				.name	= "port4",
++			},
++		},
++	},
++
++	.leds = {
++		{
++			.name		= "96368MVNgr:green:adsl",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "96368MVNgr:green:inet",
++			.gpio		= 5,
++		},
++		{
++			.name		= "96368MVNgr:green:power",
++			.gpio		= 22,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "96368MVNgr:green:wps",
++			.gpio		= 23,
++			.active_low	= 1,
++		},
++		{
++			.name		= "96368MVNgr:green:inet-fail",
++			.gpio		= 3,
++		},
++	},
++
++	.has_ohci0 = 1,
++	.has_ehci0 = 1,
++};
+ #endif
+ 
+ /*
+@@ -2316,6 +2382,7 @@ static const struct board_info __initcon
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6368
+ 	&board_96368mvwg,
++	&board_96368mvngr,
+ #endif
+ };
+ 

target/linux/brcm63xx/patches-3.8/522-MIPS-BCM63XX-add-96328avng-reference-board.patch

@@ -0,0 +1,67 @@
+From c93c2bbf0cc96da5a47d77f01daf6c983cfe4216 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 29 May 2012 10:52:25 +0200
+Subject: [PATCH] MIPS: BCM63XX: add 96328avng reference board
+
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c |   77 +++++++++++++++++++++++++++++
+ 1 files changed, 77 insertions(+), 0 deletions(-)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -73,13 +73,45 @@ static struct board_info __initdata boar
+ 		.port_no		= 0,
+ 	},
+ 
++	.has_enetsw			= 1,
++
++	.enetsw = {
++		.used_ports = {
++			[0] = {
++				.used	= 1,
++				.phy_id = 1,
++				.name	= "Port 1",
++			},
++			[1] = {
++				.used	= 1,
++				.phy_id	= 2,
++				.name	= "Port 2",
++			},
++			[2] = {
++				.used	= 1,
++				.phy_id	= 3,
++				.name	= "Port 3",
++			},
++			[3] = {
++				.used	= 1,
++				.phy_id	= 4,
++				.name	= "Port 4",
++			},
++		},
++	},
++
+ 	.leds = {
+ 		{
+-			.name		= "96328avng::ppp-fail",
++			.name		= "96328avng::internet-fail",
+ 			.gpio		= 2,
+ 			.active_low	= 1,
+ 		},
+ 		{
++			.name		= "96328avng::dsl",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{
+ 			.name		= "96328avng::power",
+ 			.gpio		= 4,
+ 			.active_low	= 1,
+@@ -96,7 +128,7 @@ static struct board_info __initdata boar
+ 			.active_low	= 1,
+ 		},
+ 		{
+-			.name		= "96328avng::ppp",
++			.name		= "96328avng::internet",
+ 			.gpio		= 11,
+ 			.active_low	= 1,
+ 		},

target/linux/brcm63xx/patches-3.8/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch

@@ -0,0 +1,96 @@
+From f0649f7b7c672cf452a1796a1422bf615e1973f8 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Tue, 29 May 2012 11:01:12 +0200
+Subject: [PATCH] MIPS: BCM63XX: add 963281TAN reference board
+
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c |   71 +++++++++++++++++++++++++++++
+ 1 files changed, 71 insertions(+), 0 deletions(-)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -134,6 +134,76 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_963281TAN = {
++	.name				= "963281TAN",
++	.expected_cpu_id		= 0x6328,
++
++	.has_uart0			= 1,
++	.has_pci			= 1,
++
++	.has_enetsw			= 1,
++
++	.enetsw = {
++		.used_ports = {
++			[0] = {
++				.used	= 1,
++				.phy_id = 1,
++				.name	= "Port 1",
++			},
++			[1] = {
++				.used	= 1,
++				.phy_id	= 2,
++				.name	= "Port 2",
++			},
++			[2] = {
++				.used	= 1,
++				.phy_id	= 3,
++				.name	= "Port 3",
++			},
++			[3] = {
++				.used	= 1,
++				.phy_id	= 4,
++				.name	= "Port 4",
++			},
++		},
++	},
++
++	.leds = {
++		{
++			.name		= "963281TAN::internet",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963281TAN::power",
++			.gpio		= 4,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "963281TAN::internet-fail",
++			.gpio		= 7,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963281TAN::power-fail",
++			.gpio		= 8,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963281TAN::wps",
++			.gpio		= 9,
++			.active_low	= 1,
++		},
++		{
++			.name		= "963281TAN::dsl",
++			.gpio		= 11,
++			.active_low	= 1,
++		},
++
++	},
++};
+ #endif
+ 
+ /*
+@@ -2365,6 +2435,7 @@ static struct board_info __initdata boar
+ static const struct board_info __initconst *bcm963xx_boards[] = {
+ #ifdef CONFIG_BCM63XX_CPU_6328
+ 	&board_96328avng,
++	&board_963281TAN,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_6338
+ 	&board_96338gw,

target/linux/brcm63xx/patches-3.8/524-board_dsl_274xb_rev_f.patch

@@ -0,0 +1,132 @@
+From 66808f706b3dcd83a9f5157997ff478a880a2906 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Mon, 30 Apr 2012 09:10:51 +0200
+Subject: [PATCH 70/79] MIPS: BCM63XX: Add board definition for D-Link
+ DSL-274xB rev F1
+
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c |  104 +++++++++++++++++++++++++++++
+ 1 files changed, 104 insertions(+), 0 deletions(-)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -204,6 +204,111 @@ static struct board_info __initdata boar
+ 
+ 	},
+ };
++
++static struct board_info __initdata board_dsl_274xb_f1 = {
++	.name				= "AW4339U",
++	.expected_cpu_id		= 0x6328,
++
++	.has_uart0			= 1,
++	.has_pci			= 1,
++
++	.has_caldata			= 1,
++	.caldata = {
++		{
++			.vendor		= PCI_VENDOR_ID_ATHEROS,
++			.caldata_offset	= 0x7d1000,
++			.slot		= 0,
++			.led_pin	= -1,
++		},
++	},
++
++	.has_enetsw			= 1,
++
++	.enetsw = {
++		.used_ports = {
++			[0] = {
++				.used	= 1,
++				.phy_id = 1,
++				.name	= "Port 4",
++			},
++			[1] = {
++				.used	= 1,
++				.phy_id	= 2,
++				.name	= "Port 3",
++			},
++			[2] = {
++				.used	= 1,
++				.phy_id	= 3,
++				.name	= "Port 2",
++			},
++			[3] = {
++				.used	= 1,
++				.phy_id	= 4,
++				.name	= "Port 1",
++			},
++		},
++	},
++
++	.leds = {
++		{
++			.name		= "dsl-274xb:red:internet",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "dsl-274xb:green:dsl",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{
++			.name		= "dsl-274xb:green:power",
++			.gpio		= 4,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "dsl-274xb:red:power",
++			.gpio		= 8,
++			.active_low	= 1,
++		},
++		{
++			.name		= "dsl-274xb:blue:wps",
++			.gpio		= 9,
++			.active_low	= 1,
++		},
++		{
++			.name		= "dsl-274xb:green:internet",
++			.gpio		= 11,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "wifi",
++			.gpio		= 10,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= BTN_0,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "reset",
++			.gpio		= 23,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 24,
++			.active_low	= 1,
++			.code		= KEY_WPS_BUTTON,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -2436,6 +2541,7 @@ static const struct board_info __initcon
+ #ifdef CONFIG_BCM63XX_CPU_6328
+ 	&board_96328avng,
+ 	&board_963281TAN,
++	&board_dsl_274xb_f1,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_6338
+ 	&board_96338gw,

target/linux/brcm63xx/patches-3.8/525-board_96348w3.patch

@@ -0,0 +1,70 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1363,6 +1363,59 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++/* NetGear DG834G v4 */
++static struct board_info __initdata board_96348W3 = {
++ 	.name	 			= "96348W3",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0	 		= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0	 		= 1,
++
++	.leds = {
++		{
++			.name		= "96348W3:green:power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "96348W3:red:power",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++		{
++			.name		= "96348W3::adsl",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "96348W3::internet",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++			{
++			.desc		= "reset",
++			.gpio		= 6,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++			},
++	},
++};
++
+ #endif
+ 
+ /*
+@@ -2571,6 +2624,7 @@ static const struct board_info __initcon
+ 	&board_ct536_ct5621,
+ 	&board_96348A_122,
+ 	&board_CPVA502plus,
++	&board_96348W3,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358

target/linux/brcm63xx/patches-3.8/526-board_CT6373-1.patch

@@ -0,0 +1,138 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -54,6 +54,13 @@
+ #define NB4_SPI_GPIO_CLK	6
+ #define NB4_74HC64_GPIO(X)	(NB4_74X164_GPIO_BASE + (X))
+ 
++#define CT6373_PID_OFFSET		0xff80
++#define CT6373_74X164_GPIO_BASE	64
++#define CT6373_SPI_GPIO_MOSI	7
++#define CT6373_SPI_GPIO_CLK		6
++#define CT6373_74HC64_GPIO(X)	(CT6373_74X164_GPIO_BASE + (X))
++
++
+ static struct board_info board;
+ 
+ /*
+@@ -2306,6 +2313,113 @@ static struct board_info __initdata boar
+ 	.num_spis = ARRAY_SIZE(nb4_spi_devices),
+ };
+ 
++
++struct spi_gpio_platform_data ct6373_spi_gpio_data = {
++	.sck		= CT6373_SPI_GPIO_CLK,
++	.mosi		= CT6373_SPI_GPIO_MOSI,
++	.miso		= SPI_GPIO_NO_MISO,
++	.num_chipselect	= 1,
++};
++
++static struct platform_device ct6373_spi_gpio = {
++	.name = "spi_gpio",
++	.id   = 1,
++	.dev = {
++		.platform_data = &ct6373_spi_gpio_data,
++	},
++};
++
++static struct platform_device * __initdata ct6373_devices[] = {
++	&ct6373_spi_gpio,
++};
++
++const struct gen_74x164_chip_platform_data ct6373_74x164_platform_data = {
++	.base = CT6373_74X164_GPIO_BASE
++};
++
++static struct spi_board_info ct6373_spi_devices[] = {
++	{
++		.modalias = "74x164",
++		.max_speed_hz = 781000,
++		.bus_num = 1,
++		.controller_data = (void *) SPI_GPIO_NO_CHIPSELECT,
++		.mode = SPI_MODE_0,
++		.platform_data = &ct6373_74x164_platform_data
++	}
++};
++
++static struct board_info __initdata board_ct6373_1 = {
++	.name				= "CT6373-1",
++	.expected_cpu_id	= 0x6358,
++
++	.has_uart0			= 1,
++	.has_pci			= 1,
++	.has_ohci0			= 1,
++	.has_ehci0			= 1,
++
++	.has_enet1			= 1,
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.leds = {
++		{
++			.name		= "CT6373-1:green:power",
++			.gpio		= 0,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "CT6373-1:green:usb",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CT6373-1:green:wlan",
++			.gpio		= 9,
++			.active_low	= 1,
++		},
++		{
++			.name		= "CT6373-1:green:adsl",
++			.gpio		= CT6373_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "CT6373-1:green:line",
++			.gpio		= CT6373_74HC64_GPIO(1),
++			.active_low	= 1,
++		},
++		{
++			.name		= "CT6373-1:green:fxs1",
++			.gpio		= CT6373_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "CT6373-1:green:fxs2",
++			.gpio		= CT6373_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 35,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++
++	.devs = ct6373_devices,
++	.num_devs = ARRAY_SIZE(ct6373_devices),
++	.spis = ct6373_spi_devices,
++	.num_spis = ARRAY_SIZE(ct6373_spi_devices),
++};
++
+ static struct board_info __initdata board_HW553 = {
+ 	.name                           = "HW553",
+ 	.expected_cpu_id                = 0x6358,
+@@ -2639,6 +2753,7 @@ static const struct board_info __initcon
+ 	&board_nb4_ser_r2,
+ 	&board_nb4_fxc_r1,
+ 	&board_nb4_fxc_r2,
++	&board_ct6373_1,
+ 	&board_HW553,
+ 	&board_spw303v,
+ #endif

target/linux/brcm63xx/patches-3.8/527-board_dva-g3810bn-tl-1.patch

@@ -0,0 +1,84 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -2561,6 +2561,73 @@ static struct board_info __initdata boar
+ 		},
+ 	}
+ };
++
++/* D-Link DVA-G3810BN/TL */
++static struct board_info __initdata board_DVAG3810BN = {
++	.name			= "DVAG3810BN",
++	.expected_cpu_id	= 0x6358,
++
++	.has_uart0		= 1,
++	.has_enet0		= 1,
++	.has_enet1		= 1,
++	.has_pci		= 1,
++
++	.enet0 = {
++		.has_phy		= 0,
++		.use_internal_phy	= 1,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.enet1 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0		= 1,
++	.has_pccard		= 1,
++	.has_ehci0		= 1,
++
++	.leds = {
++		{
++			.name	= "DVAG3810BN::voip",
++			.gpio	= 1,
++		},
++		{
++			.name	= "DVAG3810BN::dsl",
++			.gpio	= 22,
++			.active_low  = 1,
++		},
++		{
++			.name	= "DVAG3810BN::internet",
++			.gpio	= 23,
++			.active_low  = 1,
++		},
++		{
++			.name	= "DVAG3810BN::power",
++			.gpio	= 4,
++			.default_trigger = "default-on",
++		},
++		{
++			.name	= "DVAG3810BN::stop",
++			.gpio	= 5,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc	= "reset",
++			.gpio	= 34,
++			.active_low = 1,
++			.type	= EV_KEY,
++			.code	= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -2756,6 +2823,7 @@ static const struct board_info __initcon
+ 	&board_ct6373_1,
+ 	&board_HW553,
+ 	&board_spw303v,
++	&board_DVAG3810BN,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6368

target/linux/brcm63xx/patches-3.8/528-board_nb6.patch

@@ -0,0 +1,146 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -17,6 +17,7 @@
+ #include <linux/spi/spi.h>
+ #include <linux/spi/spi_gpio.h>
+ #include <linux/spi/74x164.h>
++#include <linux/rtl8367.h>
+ #include <asm/addrspace.h>
+ #include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+@@ -53,6 +54,8 @@
+ #define NB4_SPI_GPIO_MOSI	7
+ #define NB4_SPI_GPIO_CLK	6
+ #define NB4_74HC64_GPIO(X)	(NB4_74X164_GPIO_BASE + (X))
++#define NB6_GPIO_RTL8367_SDA	18
++#define NB6_GPIO_RTL8367_SCK	20
+ 
+ #define CT6373_PID_OFFSET		0xff80
+ #define CT6373_74X164_GPIO_BASE	64
+@@ -2630,6 +2633,103 @@ static struct board_info __initdata boar
+ };
+ #endif
+ 
++#ifdef CONFIG_BCM63XX_CPU_6362
++static struct rtl8367_extif_config nb6_rtl8367_extif0_cfg = {
++	.mode = RTL8367_EXTIF_MODE_RGMII,
++	.txdelay = 1,
++	.rxdelay = 5,
++	.ability = {
++		.force_mode = 1,
++		.txpause = 1,
++		.rxpause = 1,
++		.link = 1,
++		.duplex = 1,
++		.speed = RTL8367_PORT_SPEED_1000,
++	},
++};
++
++static struct rtl8367_platform_data nb6_rtl8367_data = {
++	.gpio_sda	= NB6_GPIO_RTL8367_SDA,
++	.gpio_sck	= NB6_GPIO_RTL8367_SCK,
++	.extif0_cfg	= &nb6_rtl8367_extif0_cfg,
++};
++
++static struct platform_device nb6_rtl8367_device = {
++	.name		= RTL8367_DRIVER_NAME,
++	.id		= -1,
++	.dev = {
++		.platform_data	= &nb6_rtl8367_data,
++	}
++};
++
++static struct platform_device * __initdata nb6_devices[] = {
++	&nb6_rtl8367_device,
++};
++
++static struct board_info __initdata board_nb6 = {
++	.name				= "NB6",
++	.expected_cpu_id		= 0x6362,
++
++	.has_uart0			= 1,
++
++	.has_ohci0			= 1,
++	.has_ehci0			= 1,
++
++	.has_enetsw			= 1,
++
++	.enetsw = {
++		.used_ports = {
++			[4] = {
++				.used	= 1,
++				.phy_id	= 0xff,
++				.bypass_link = 1,
++				.force_speed = 1000,
++				.force_duplex_full = 1,
++				.name	= "RGMII",
++			},
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 24,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++			.active_low	= 1,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 25,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++			.active_low	= 1,
++		},
++		{
++			.desc		= "wlan",
++			.gpio		= 12,
++			.type		= EV_KEY,
++			.code		= KEY_WLAN,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++			.active_low	= 1,
++		},
++		{
++			.desc		= "service",
++			.gpio		= 10,
++			.type		= EV_KEY,
++			.code		= BTN_0,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++			.active_low	= 1,
++		},
++	},
++
++	.devs = nb6_devices,
++	.num_devs = ARRAY_SIZE(nb6_devices),
++};
++#endif
++
+ /*
+  * known 6368 boards
+  */
+@@ -2826,6 +2926,10 @@ static const struct board_info __initcon
+ 	&board_DVAG3810BN,
+ #endif
+ 
++#ifdef CONFIG_BCM63XX_CPU_6362
++	&board_nb6,
++#endif
++
+ #ifdef CONFIG_BCM63XX_CPU_6368
+ 	&board_96368mvwg,
+ 	&board_96368mvngr,
+@@ -2893,6 +2997,11 @@ static void __init boardid_fixup(u8 *boo
+ 		}
+ 	}
+ 
++	if (BCMCPU_IS_6362() && (!strncmp(board_name, "NB6-", sizeof("NB6-") - 1))) {
++		board_name[sizeof("NB6") - 1] = '\0';
++		return ;
++	}
++
+ 	/* check if bcm_tag is at 64k offset */
+ 	if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) {
+ 		/* else try 128k */

target/linux/brcm63xx/patches-3.8/529-board_fast2604.patch

@@ -0,0 +1,68 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1031,6 +1031,57 @@ static struct board_info __initdata boar
+ 	.has_ehci0			= 1,
+ };
+ 
++static struct board_info __initdata board_FAST2604 = {
++	.name						= "F@ST2604",
++	.expected_cpu_id			= 0x6348,
++
++	.has_uart0					= 1,
++	.has_pci					= 1,
++	.has_ohci0					= 1,
++
++	.has_enet1					= 1,
++	.enet1 = {
++		.has_phy			= 1,
++		.phy_id				= 0,
++		.force_speed_100		= 1,
++		.force_duplex_full		= 1,
++	},
++
++	.leds = {
++		{
++			.name				= "F@ST2604:green:power",
++			.gpio				= 0,
++			.active_low			= 1,
++			.default_trigger	= "default-on",
++		},
++		{
++			.name				= "F@ST2604:red:power",
++			.gpio				= 1,
++			.active_low			= 1,
++		},
++		{
++			.name				= "F@ST2604:red:inet",
++			.gpio				= 4,
++			.active_low			= 1,
++		},
++		{
++			.name				= "F@ST2604:green:wps",
++			.gpio				= 5,
++			.active_low			= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc				= "reset",
++			.gpio				= 33,
++			.active_low			= 1,
++			.type				= EV_KEY,
++			.code				= KEY_RESTART,
++			.debounce_interval	= BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
+ static struct board_info __initdata board_rta1025w_16 = {
+ 	.name				= "RTA1025W_16",
+ 	.expected_cpu_id		= 0x6348,
+@@ -2894,6 +2945,7 @@ static const struct board_info __initcon
+ 	&board_96348gw_10,
+ 	&board_96348gw_11,
+ 	&board_FAST2404,
++	&board_FAST2604,
+ 	&board_DV201AMR,
+ 	&board_96348gw_a,
+ 	&board_rta1025w_16,