mirror of https://github.com/hak5/openwrt-owl.git
ramips: add support for TP-Link Archer C2
Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0
Preparing a TFTP recovery image for initial flashing:
Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!
Create a TFTP recovery image:
1) Download a stock TP-Link Firmware file here:
https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
#> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
#> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin
The resulting image can be flashed via TFTP recovery mode.
Flash instructions:
1) To flash the recovery image, start a TFTP server from IP address
192.168.0.66 and serve the recovery image named
ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
and power it up. Keep pressing the WPS/Reset button for 10 seconds.
It will try to download the recovery image and flash it.
It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
master
Franz Flasch
Mathias Kresin
parent
abb7524683
commit
8375623a06
|
|
@ -398,6 +398,12 @@ tl-wr841n-v13)
|
|||
ucidef_set_led_switch "lan4" "lan4" "$boardname:green:lan4" "switch0" "0x10"
|
||||
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"
|
||||
;;
|
||||
tplink,c2-v1)
|
||||
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch1" "0x1e"
|
||||
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch1" "0x01"
|
||||
set_usb_led "$boardname:green:usb" "2-1"
|
||||
set_wifi_led "$boardname:green:wlan"
|
||||
;;
|
||||
tplink,c20-v1)
|
||||
ucidef_set_led_switch "lan" "lan" "$boardname:blue:lan" "switch0" "0x1e"
|
||||
ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x01"
|
||||
|
|
|
|||
|
|
@ -335,6 +335,10 @@ ramips_setup_interfaces()
|
|||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
|
||||
;;
|
||||
tplink,c2-v1)
|
||||
ucidef_add_switch "switch1" \
|
||||
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
|
||||
;;
|
||||
tplink,tl-wr902ac-v3)
|
||||
ucidef_add_switch "switch0" \
|
||||
"4:lan" "6@eth0"
|
||||
|
|
|
|||
|
|
@ -79,6 +79,7 @@ get_status_led() {
|
|||
awapn2403|\
|
||||
dir-645|\
|
||||
sk-wb8|\
|
||||
tplink,c2-v1|\
|
||||
wrh-300cr)
|
||||
status_led="$boardname:green:wps"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -253,6 +253,7 @@ platform_check_image() {
|
|||
c20i|\
|
||||
c50|\
|
||||
mr200|\
|
||||
tplink,c2-v1|\
|
||||
tplink,c20-v1|\
|
||||
tplink,c20-v4|\
|
||||
tplink,c50-v3|\
|
||||
|
|
|
|||
|
|
@ -0,0 +1,178 @@
|
|||
/dts-v1/;
|
||||
|
||||
/include/ "mt7620a.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "tplink,c2-v1", "ralink,mt7620a-soc";
|
||||
model = "TP-Link Archer C2 v1";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "i2c", "uartf", "wled", "ephy", "spi refclk";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
lan {
|
||||
label = "c2-v1:green:lan";
|
||||
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "c2-v1:green:usb";
|
||||
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "c2-v1:green:wps";
|
||||
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "c2-v1:green:wan";
|
||||
gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan {
|
||||
label = "c2-v1:green:wlan";
|
||||
gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset_wps {
|
||||
label = "reset_wps";
|
||||
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
rfkill {
|
||||
label = "rfkill";
|
||||
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RFKILL>;
|
||||
};
|
||||
};
|
||||
|
||||
rtl8367rb {
|
||||
compatible = "realtek,rtl8367b", "rtl8367b";
|
||||
cpu_port = <6>;
|
||||
realtek,extif1 = <1 0 1 1 1 1 1 1 2>;
|
||||
mii-bus = <&mdio0>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
m25p80@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "firmware";
|
||||
reg = <0x20000 0x7a0000>;
|
||||
};
|
||||
|
||||
partition@7c0000 {
|
||||
label = "config";
|
||||
reg = <0x7c0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
rom: partition@7d0000 {
|
||||
label = "rom";
|
||||
reg = <0x7d0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7e0000 {
|
||||
label = "romfile";
|
||||
reg = <0x7e0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
radio: partition@7f0000 {
|
||||
label = "radio";
|
||||
reg = <0x7f0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
status = "okay";
|
||||
mtd-mac-address = <&rom 0xf100>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;
|
||||
|
||||
port@5 {
|
||||
status = "okay";
|
||||
mediatek,fixed-link = <1000 1 1 1>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
mdio0: mdio-bus {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
&gpio1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
ralink,mtd-eeprom = <&radio 0>;
|
||||
mtd-mac-address = <&rom 0xf100>;
|
||||
};
|
||||
|
||||
&ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ohci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
pcie-bridge {
|
||||
mt76@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
device_type = "pci";
|
||||
mediatek,mtd-eeprom = <&radio 0x8000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -472,6 +472,18 @@ define Device/tiny-ac
|
|||
endef
|
||||
TARGET_DEVICES += tiny-ac
|
||||
|
||||
define Device/tplink_c2-v1
|
||||
$(Device/Archer)
|
||||
DTS := ArcherC2-v1
|
||||
TPLINK_FLASHLAYOUT := 8Mmtk
|
||||
TPLINK_HWID := 0xc7500001
|
||||
TPLINK_HWREV := 50
|
||||
IMAGES += factory.bin
|
||||
DEVICE_TITLE := TP-Link Archer C2 v1
|
||||
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport kmod-switch-rtl8366-smi kmod-switch-rtl8367b
|
||||
endef
|
||||
TARGET_DEVICES += tplink_c2-v1
|
||||
|
||||
define Device/tplink_c20-v1
|
||||
$(Device/Archer)
|
||||
DTS := ArcherC20v1
|
||||
|
|
|
|||
Loading…
Reference in New Issue