ipq806x: disable DMA on the SPI flash

Previous patch 6f2905eeb6ce5ddec8d12d677e1f377a940b537b enabled ADM in
the kernel, which causes a kernel panic when accessing the SPI flash.

As a workaround, We'll disable DMA for the flash for now. It was not
enabled previously anyway so we'll just leave it as is.

Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 46587

target/linux/ipq806x/patches-3.18/157-ARM-DT-ipq8064-Add-ADM-device-node.patch

@@ -11,19 +11,6 @@ Signed-off-by: Andy Gross <agross@codeaurora.org>
  arch/arm/boot/dts/qcom-ipq8064.dtsi      | 21 +++++++++++++++++++++
  2 files changed, 25 insertions(+)
 
---- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-+++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-@@ -90,6 +90,10 @@
- 
- 				cs-gpios = <&qcom_pinmux 20 0>;
- 
-+				dmas = <&adm_dma 6>,
-+					<&adm_dma 5>;
-+				dma-names = "rx", "tx";
-+
- 				flash: m25p80@0 {
- 					compatible = "s25fl256s1";
- 					#address-cells = <1>;
 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
 +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
 @@ -657,5 +657,25 @@

target/linux/ipq806x/patches-3.18/165-arm-qcom-dts-Enable-NAND-node-on-IPQ8064-AP148-platform.patch

@@ -57,7 +57,7 @@ arch/arm/boot/dts/qcom-ipq8064-ap148.dts | 36 ++++++++++++++++++++++++++++++++
  		};
  
  		gsbi@16300000 {
-@@ -174,5 +199,19 @@
+@@ -170,5 +195,19 @@
  			pinctrl-0 = <&pcie1_pins>;
  			pinctrl-names = "default";
  		};

target/linux/ipq806x/patches-3.18/707-ARM-dts-qcom-add-mdio-nodes-to-ap148-db149.patch

@@ -38,7 +38,7 @@ Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
  		};
  
  		gsbi@16300000 {
-@@ -209,6 +219,34 @@
+@@ -205,6 +215,34 @@
  			nand-ecc-strength = <4>;
  			nand-bus-width = <8>;
  		};

target/linux/ipq806x/patches-3.18/708-ARM-dts-qcom-add-gmac-nodes-to-ipq806x-platforms.patch

@@ -29,7 +29,7 @@ Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
  		};
  
  		gsbi@16300000 {
-@@ -247,6 +257,27 @@
+@@ -243,6 +253,27 @@
  				reg = <4>;
  			};
  		};