mirror of https://github.com/hak5/openwrt-owl.git
ipq806x: overhaul AVM FRITZ!box 4040 device-tree file
This patch aligns the device-tree file with the latest guidelines. - No longer include qcom-ipq4019-ap.dk01.1.dtsi. This file is only partially upstream and therefore subjected to changes that might not be compatible with the board. As a result, the definitions from the file have been copied into this dts. - exclusively use decimal GPIO addresses. - reorganize the reserved-memory layout to waste less memory. There's no point in keeping the u-boot loader around. This should also make it possible to create an image that will boot with the original EVA/ADAM2 loader without needing to install the modified u-boot loader. And finally mark the "tz-apps" as reusable. There isn't a way to upload apps to the trust-zone in OpenWrt yet. But it might see some use in the future as a "secure" key-store/TPM. - sort the first-level nodes alphabetically. - sort nodes with an address by the address. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>owl
Christian Lamparter
Mathias Kresin
parent
8d755ef052
commit
42b47f1b40
|
|
@ -14,51 +14,107 @@
|
|||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019-ap.dk01.1.dtsi"
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include "qcom-ipq4019-bus.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "AVM FRITZ!Box 4040";
|
||||
compatible = "avm,fritzbox-4040", "qcom,ipq4019";
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <0x1>;
|
||||
#size-cells = <0x1>;
|
||||
ranges;
|
||||
|
||||
rsvd1@87000000 {
|
||||
reg = <0x87000000 0x500000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
wifi_dump@87500000 {
|
||||
reg = <0x87500000 0x600000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
rsvd2@87B00000 {
|
||||
reg = <0x87b00000 0x500000>;
|
||||
no-map;
|
||||
};
|
||||
aliases {
|
||||
led-boot = &power;
|
||||
led-failsafe = &flash;
|
||||
led-running = &power;
|
||||
led-upgrade = &flash;
|
||||
};
|
||||
/*
|
||||
This also works. Maybe it could be smaller still.
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <0x1>;
|
||||
#size-cells = <0x1>;
|
||||
ranges;
|
||||
|
||||
rsvd1@87E00000 {
|
||||
reg = <0x87e00000 0x200000>;
|
||||
tz_apps@87b80000 {
|
||||
reg = <0x87b80000 0x280000>;
|
||||
reusable;
|
||||
};
|
||||
|
||||
smem@87e00000 {
|
||||
reg = <0x87e00000 0x080000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
tz@87e80000 {
|
||||
reg = <0x87e80000 0x180000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
*/
|
||||
|
||||
soc {
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2@60f8800 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
serial@78af000 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
wifi@a000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
wifi@a800000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
qca8075: ess-switch@c000000 {
|
||||
status = "okay";
|
||||
|
||||
|
|
@ -68,10 +124,14 @@
|
|||
enable-usb-power {
|
||||
gpio-hog;
|
||||
line-name = "enable USB3 power";
|
||||
gpios = <0x7 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <7 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
|
|
@ -79,7 +139,7 @@
|
|||
|
||||
wlan {
|
||||
label = "wlan";
|
||||
gpios = <&tlmm 0x3a GPIO_ACTIVE_LOW>;
|
||||
gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RFKILL>;
|
||||
};
|
||||
|
||||
|
|
@ -90,52 +150,85 @@
|
|||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &power;
|
||||
led-failsafe = &flash;
|
||||
led-running = &power;
|
||||
led-upgrade = &flash;
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
wlan {
|
||||
label = "fritz4040:green:wlan";
|
||||
gpios = <&qca8075 0x1 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&qca8075 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
panic: info_red {
|
||||
label = "fritz4040:red:info";
|
||||
gpios = <&qca8075 0x3 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&qca8075 3 GPIO_ACTIVE_HIGH>;
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "fritz4040:green:wan";
|
||||
gpios = <&qca8075 0x5 GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&qca8075 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
power: power {
|
||||
label = "fritz4040:green:power";
|
||||
gpios = <&qca8075 0xb GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&qca8075 11 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "fritz4040:green:lan";
|
||||
gpios = <&qca8075 0xd GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&qca8075 13 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
flash: info_amber {
|
||||
label = "fritz4040:amber:info";
|
||||
gpios = <&qca8075 0xf GPIO_ACTIVE_HIGH>;
|
||||
gpios = <&qca8075 15 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
mux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
mux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&spi_0 { /* BLSP1 QUP1 */
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "ok";
|
||||
cs-gpios = <&tlmm 54 0>;
|
||||
|
||||
mx25l25635f@0 {
|
||||
compatible = "mx25l25635f", "jedec,spi-nor";
|
||||
compatible = "jedec,spi-nor";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0>;
|
||||
|
|
@ -206,12 +299,24 @@
|
|||
};
|
||||
partition11@2A0000 {
|
||||
label = "firmware";
|
||||
reg = <0x002A0000 0x01C60000>;
|
||||
reg = <0x002a0000 0x01c60000>;
|
||||
};
|
||||
partition12@1f00000 {
|
||||
label = "jffs2";
|
||||
reg = <0x01F00000 0x00100000>;
|
||||
reg = <0x01f00000 0x00100000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "ok";
|
||||
};
|
||||
|
|
|
|||
Loading…
Reference in New Issue