brcm47xx: fix commit r18413 "128MB ram problem"

The patch commited in r18413 was wrong.
This patch prevents prom_init_mem from scanning over 128MB ram.
This is from #6765 and #3177

Refresh all patches

SVN-Revision: 20072

target/linux/brcm47xx/patches-2.6.30/170-128MB_ram_bugfix.patch

@@ -1,17 +1,32 @@
 --- a/arch/mips/bcm47xx/prom.c
 +++ b/arch/mips/bcm47xx/prom.c
-@@ -141,6 +141,14 @@ static __init void prom_init_mem(void)
+@@ -126,6 +126,7 @@ static __init void prom_init_cmdline(voi
+ static __init void prom_init_mem(void)
+ {
+ 	unsigned long mem;
++	unsigned long max;
+ 
+ 	/* Figure out memory size by finding aliases.
+ 	 *
+@@ -134,8 +135,21 @@ static __init void prom_init_mem(void)
+ 	 * want to reuse the memory used by CFE (around 4MB). That means cfe_*
+ 	 * functions stop to work at some point during the boot, we should only
+ 	 * call them at the beginning of the boot.
++	 * 
++	 * BCM47XX uses 128MB for addressing the ram, if the system contains
++	 * less that that amount of ram it remaps the ram more often into the
++	 * available space.
++	 * Accessing memory after 128MB will cause an exception.
++	 * max contains the biggest possible address supported by the platform.
++	 * If the method wants to try something above we assume 128MB ram.
+ 	 */
++	max = ((unsigned long)(prom_init) | ((128 << 20) - 1));
+ 	for (mem = (1 << 20); mem < (128 << 20); mem += (1 << 20)) {
++		if (((unsigned long)(prom_init) + mem) > max) {
++			mem = (128 << 20);
++			printk("assume 128MB RAM\n");
++			break;
++		}
+ 		if (*(unsigned long *)((unsigned long)(prom_init) + mem) ==
+ 		    *(unsigned long *)(prom_init))
  			break;
- 	}
- 
-+	/* Ignoring the last page when ddr size is 128M. Cached
-+	 * accesses to last page is causing the processor to prefetch
-+	 * using address above 128M stepping out of the ddr address
-+	 * space.
-+	 */
-+	if (mem == 0x8000000)
-+		mem -= 0x1000;
-+
- 	add_memory_region(0, mem, BOOT_MEM_RAM);
- }
- 

target/linux/brcm47xx/patches-2.6.30/700-ssb-gigabit-ethernet-driver.patch

@@ -252,7 +252,7 @@
  	if (tp->tg3_flags & TG3_FLAG_EEPROM_WRITE_PROT) {
  		tw32_f(GRC_LOCAL_CTRL, tp->grc_local_ctrl &
  		       ~GRC_LCLCTRL_GPIO_OUTPUT1);
-@@ -12099,6 +12168,11 @@ static int __devinit tg3_get_invariants(
+@@ -12099,6 +12169,11 @@ static int __devinit tg3_get_invariants(
  	      GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5701)))
  		tp->tg3_flags |= TG3_FLAG_SRAM_USE_CONFIG;
  
@@ -264,7 +264,7 @@
  	/* Get eeprom hw config before calling tg3_set_power_state().
  	 * In particular, the TG3_FLG2_IS_NIC flag must be
  	 * determined before calling tg3_set_power_state() so that
-@@ -12474,6 +12548,10 @@ static int __devinit tg3_get_device_addr
+@@ -12474,6 +12549,10 @@ static int __devinit tg3_get_device_addr
  	}
  
  	if (!is_valid_ether_addr(&dev->dev_addr[0])) {
@@ -275,7 +275,7 @@
  #ifdef CONFIG_SPARC
  		if (!tg3_get_default_macaddr_sparc(tp))
  			return 0;
-@@ -12965,6 +13043,7 @@ static char * __devinit tg3_phy_string(s
+@@ -12965,6 +13044,7 @@ static char * __devinit tg3_phy_string(s
  	case PHY_ID_BCM5704:	return "5704";
  	case PHY_ID_BCM5705:	return "5705";
  	case PHY_ID_BCM5750:	return "5750";
@@ -283,7 +283,7 @@
  	case PHY_ID_BCM5752:	return "5752";
  	case PHY_ID_BCM5714:	return "5714";
  	case PHY_ID_BCM5780:	return "5780";
-@@ -13175,6 +13254,13 @@ static int __devinit tg3_init_one(struct
+@@ -13175,6 +13255,13 @@ static int __devinit tg3_init_one(struct
  		tp->msg_enable = tg3_debug;
  	else
  		tp->msg_enable = TG3_DEF_MSG_ENABLE;

target/linux/brcm47xx/patches-2.6.30/800-fix_cfe_detection.patch

@@ -90,7 +90,7 @@
  {
  	char buf[CL_SIZE];
  
-@@ -154,9 +130,12 @@ static __init void prom_init_mem(void)
+@@ -160,9 +136,12 @@ static __init void prom_init_mem(void)
  
  void __init prom_init(void)
  {

target/linux/brcm47xx/patches-2.6.31/170-128MB_ram_bugfix.patch

@@ -1,17 +1,32 @@
 --- a/arch/mips/bcm47xx/prom.c
 +++ b/arch/mips/bcm47xx/prom.c
-@@ -141,6 +141,14 @@ static __init void prom_init_mem(void)
+@@ -126,6 +126,7 @@ static __init void prom_init_cmdline(voi
+ static __init void prom_init_mem(void)
+ {
+ 	unsigned long mem;
++	unsigned long max;
+ 
+ 	/* Figure out memory size by finding aliases.
+ 	 *
+@@ -134,8 +135,21 @@ static __init void prom_init_mem(void)
+ 	 * want to reuse the memory used by CFE (around 4MB). That means cfe_*
+ 	 * functions stop to work at some point during the boot, we should only
+ 	 * call them at the beginning of the boot.
++	 * 
++	 * BCM47XX uses 128MB for addressing the ram, if the system contains
++	 * less that that amount of ram it remaps the ram more often into the
++	 * available space.
++	 * Accessing memory after 128MB will cause an exception.
++	 * max contains the biggest possible address supported by the platform.
++	 * If the method wants to try something above we assume 128MB ram.
+ 	 */
++	max = ((unsigned long)(prom_init) | ((128 << 20) - 1));
+ 	for (mem = (1 << 20); mem < (128 << 20); mem += (1 << 20)) {
++		if (((unsigned long)(prom_init) + mem) > max) {
++			mem = (128 << 20);
++			printk("assume 128MB RAM\n");
++			break;
++		}
+ 		if (*(unsigned long *)((unsigned long)(prom_init) + mem) ==
+ 		    *(unsigned long *)(prom_init))
  			break;
- 	}
- 
-+	/* Ignoring the last page when ddr size is 128M. Cached
-+	 * accesses to last page is causing the processor to prefetch
-+	 * using address above 128M stepping out of the ddr address
-+	 * space.
-+	 */
-+	if (mem == 0x8000000)
-+		mem -= 0x1000;
-+
- 	add_memory_region(0, mem, BOOT_MEM_RAM);
- }
- 

target/linux/brcm47xx/patches-2.6.31/700-ssb-gigabit-ethernet-driver.patch

@@ -252,7 +252,7 @@
  	if (tp->tg3_flags & TG3_FLAG_EEPROM_WRITE_PROT) {
  		tw32_f(GRC_LOCAL_CTRL, tp->grc_local_ctrl &
  		       ~GRC_LCLCTRL_GPIO_OUTPUT1);
-@@ -12136,6 +12205,11 @@ static int __devinit tg3_get_invariants(
+@@ -12136,6 +12206,11 @@ static int __devinit tg3_get_invariants(
  	      GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5701)))
  		tp->tg3_flags |= TG3_FLAG_SRAM_USE_CONFIG;
  
@@ -264,7 +264,7 @@
  	/* Get eeprom hw config before calling tg3_set_power_state().
  	 * In particular, the TG3_FLG2_IS_NIC flag must be
  	 * determined before calling tg3_set_power_state() so that
-@@ -12513,6 +12587,10 @@ static int __devinit tg3_get_device_addr
+@@ -12513,6 +12588,10 @@ static int __devinit tg3_get_device_addr
  	}
  
  	if (!is_valid_ether_addr(&dev->dev_addr[0])) {
@@ -275,7 +275,7 @@
  #ifdef CONFIG_SPARC
  		if (!tg3_get_default_macaddr_sparc(tp))
  			return 0;
-@@ -13004,6 +13082,7 @@ static char * __devinit tg3_phy_string(s
+@@ -13004,6 +13083,7 @@ static char * __devinit tg3_phy_string(s
  	case PHY_ID_BCM5704:	return "5704";
  	case PHY_ID_BCM5705:	return "5705";
  	case PHY_ID_BCM5750:	return "5750";
@@ -283,7 +283,7 @@
  	case PHY_ID_BCM5752:	return "5752";
  	case PHY_ID_BCM5714:	return "5714";
  	case PHY_ID_BCM5780:	return "5780";
-@@ -13214,6 +13293,13 @@ static int __devinit tg3_init_one(struct
+@@ -13214,6 +13294,13 @@ static int __devinit tg3_init_one(struct
  		tp->msg_enable = tg3_debug;
  	else
  		tp->msg_enable = TG3_DEF_MSG_ENABLE;

target/linux/brcm47xx/patches-2.6.31/800-fix_cfe_detection.patch

@@ -90,7 +90,7 @@
  {
  	char buf[CL_SIZE];
  
-@@ -154,9 +130,12 @@ static __init void prom_init_mem(void)
+@@ -160,9 +136,12 @@ static __init void prom_init_mem(void)
  
  void __init prom_init(void)
  {

target/linux/brcm47xx/patches-2.6.32/170-128MB_ram_bugfix.patch

@@ -1,17 +1,32 @@
 --- a/arch/mips/bcm47xx/prom.c
 +++ b/arch/mips/bcm47xx/prom.c
-@@ -141,6 +141,14 @@ static __init void prom_init_mem(void)
+@@ -126,6 +126,7 @@ static __init void prom_init_cmdline(voi
+ static __init void prom_init_mem(void)
+ {
+ 	unsigned long mem;
++	unsigned long max;
+ 
+ 	/* Figure out memory size by finding aliases.
+ 	 *
+@@ -134,8 +135,21 @@ static __init void prom_init_mem(void)
+ 	 * want to reuse the memory used by CFE (around 4MB). That means cfe_*
+ 	 * functions stop to work at some point during the boot, we should only
+ 	 * call them at the beginning of the boot.
++	 * 
++	 * BCM47XX uses 128MB for addressing the ram, if the system contains
++	 * less that that amount of ram it remaps the ram more often into the
++	 * available space.
++	 * Accessing memory after 128MB will cause an exception.
++	 * max contains the biggest possible address supported by the platform.
++	 * If the method wants to try something above we assume 128MB ram.
+ 	 */
++	max = ((unsigned long)(prom_init) | ((128 << 20) - 1));
+ 	for (mem = (1 << 20); mem < (128 << 20); mem += (1 << 20)) {
++		if (((unsigned long)(prom_init) + mem) > max) {
++			mem = (128 << 20);
++			printk("assume 128MB RAM\n");
++			break;
++		}
+ 		if (*(unsigned long *)((unsigned long)(prom_init) + mem) ==
+ 		    *(unsigned long *)(prom_init))
  			break;
- 	}
- 
-+	/* Ignoring the last page when ddr size is 128M. Cached
-+	 * accesses to last page is causing the processor to prefetch
-+	 * using address above 128M stepping out of the ddr address
-+	 * space.
-+	 */
-+	if (mem == 0x8000000)
-+		mem -= 0x1000;
-+
- 	add_memory_region(0, mem, BOOT_MEM_RAM);
- }
- 

target/linux/brcm47xx/patches-2.6.32/180-ssb_extif_interrupt.patch

@@ -13,11 +13,9 @@ Signed-off-by: John W. Linville <linville@tuxdriver.com>
  drivers/ssb/driver_mipscore.c |    5 ++++-
  1 files changed, 4 insertions(+), 1 deletions(-)
 
-diff --git a/drivers/ssb/driver_mipscore.c b/drivers/ssb/driver_mipscore.c
-index 3c6feed..97efce1 100644
 --- a/drivers/ssb/driver_mipscore.c
 +++ b/drivers/ssb/driver_mipscore.c
-@@ -270,7 +270,6 @@ void ssb_mipscore_init(struct ssb_mipscore *mcore)
+@@ -270,7 +270,6 @@ void ssb_mipscore_init(struct ssb_mipsco
  				set_irq(dev, irq++);
  			}
  			break;
@@ -25,7 +23,7 @@ index 3c6feed..97efce1 100644
  		case SSB_DEV_PCI:
  		case SSB_DEV_ETHERNET:
  		case SSB_DEV_ETHERNET_GBIT:
-@@ -281,6 +280,10 @@ void ssb_mipscore_init(struct ssb_mipscore *mcore)
+@@ -281,6 +280,10 @@ void ssb_mipscore_init(struct ssb_mipsco
  				set_irq(dev, irq++);
  				break;
  			}
@@ -36,6 +34,3 @@ index 3c6feed..97efce1 100644
  		}
  	}
  	ssb_dprintk(KERN_INFO PFX "after irq reconfiguration\n");
--- 
-1.7.0
-

target/linux/brcm47xx/patches-2.6.32/800-fix_cfe_detection.patch

@@ -90,7 +90,7 @@
  {
  	static char buf[CL_SIZE] __initdata;
  
-@@ -154,9 +130,12 @@ static __init void prom_init_mem(void)
+@@ -160,9 +136,12 @@ static __init void prom_init_mem(void)
  
  void __init prom_init(void)
  {

target/linux/brcm47xx/patches-2.6.33/170-128MB_ram_bugfix.patch

@@ -0,0 +1,45 @@
+--- a/arch/mips/bcm47xx/prom.c
++++ b/arch/mips/bcm47xx/prom.c
+@@ -126,6 +126,7 @@ static __init void prom_init_cmdline(voi
+ static __init void prom_init_mem(void)
+ {
+ 	unsigned long mem;
++	unsigned long max;
+ 
+ 	/* Figure out memory size by finding aliases.
+ 	 *
+@@ -134,21 +135,26 @@ static __init void prom_init_mem(void)
+ 	 * want to reuse the memory used by CFE (around 4MB). That means cfe_*
+ 	 * functions stop to work at some point during the boot, we should only
+ 	 * call them at the beginning of the boot.
++	 * 
++	 * BCM47XX uses 128MB for addressing the ram, if the system contains
++	 * less that that amount of ram it remaps the ram more often into the
++	 * available space.
++	 * Accessing memory after 128MB will cause an exception.
++	 * max contains the biggest possible address supported by the platform.
++	 * If the method wants to try something above we assume 128MB ram.
+ 	 */
++	max = ((unsigned long)(prom_init) | ((128 << 20) - 1));
+ 	for (mem = (1 << 20); mem < (128 << 20); mem += (1 << 20)) {
++		if (((unsigned long)(prom_init) + mem) > max) {
++			mem = (128 << 20);
++			printk("assume 128MB RAM\n");
++			break;
++		}
+ 		if (*(unsigned long *)((unsigned long)(prom_init) + mem) ==
+ 		    *(unsigned long *)(prom_init))
+ 			break;
+ 	}
+ 
+-	/* Ignoring the last page when ddr size is 128M. Cached
+-	 * accesses to last page is causing the processor to prefetch
+-	 * using address above 128M stepping out of the ddr address
+-	 * space.
+-	 */
+-	if (mem == 0x8000000)
+-		mem -= 0x1000;
+-
+ 	add_memory_region(0, mem, BOOT_MEM_RAM);
+ }
+ 

target/linux/brcm47xx/patches-2.6.33/800-fix_cfe_detection.patch

@@ -90,7 +90,7 @@
  {
  	static char buf[COMMAND_LINE_SIZE] __initdata;
  
-@@ -154,9 +130,12 @@ static __init void prom_init_mem(void)
+@@ -160,9 +136,12 @@ static __init void prom_init_mem(void)
  
  void __init prom_init(void)
  {