openwrt-owl/package/iw/patches/001-nl80211_sync.patch

--- a/nl80211.h
+++ b/nl80211.h
@@ -295,7 +295,9 @@
  *	auth and assoc steps. For this, you need to specify the SSID in a
  *	%NL80211_ATTR_SSID attribute, and can optionally specify the association
  *	IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC,
- *	%NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_CONTROL_PORT.
+ *	%NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
+ *	%NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
+ *	%NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
  *	It is also sent as an event, with the BSSID and response IEs when the
  *	connection is established or failed to be established. This can be
  *	determined by the STATUS_CODE attribute.
@@ -313,8 +315,8 @@
  *	channel for the specified amount of time. This can be used to do
  *	off-channel operations like transmit a Public Action frame and wait for
  *	a response while being associated to an AP on another channel.
- *	%NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify which
- *	radio is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
+ *	%NL80211_ATTR_IFINDEX is used to specify which interface (and thus
+ *	radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
  *	frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be
  *	optionally used to specify additional channel parameters.
  *	%NL80211_ATTR_DURATION is used to specify the duration in milliseconds
@@ -385,6 +387,8 @@
  *	of any other interfaces, and other interfaces will again take
  *	precedence when they are used.
  *
+ * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -487,6 +491,7 @@ enum nl80211_commands {
 	NL80211_CMD_NOTIFY_CQM,
 
 	NL80211_CMD_SET_CHANNEL,
+	NL80211_CMD_SET_WDS_PEER,
 
 	/* add new commands above here */
 
@@ -686,6 +691,15 @@ enum nl80211_commands {
  *	request, the driver will assume that the port is unauthorized until
  *	authorized by user space. Otherwise, port is marked authorized by
  *	default in station mode.
+ * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the
+ *	ethertype that will be used for key negotiation. It can be
+ *	specified with the associate and connect commands. If it is not
+ *	specified, the value defaults to 0x888E (PAE, 802.1X). This
+ *	attribute is also used as a flag in the wiphy information to
+ *	indicate that protocols other than PAE are supported.
+ * @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with
+ *	%NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom
+ *	ethertype frames used for key negotiation must not be encrypted.
  *
  * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
  *	We recommend using nested, driver-specific attributes within this.
@@ -787,6 +801,33 @@ enum nl80211_commands {
  *      This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING
  *      for non-automatic settings.
  *
+ * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly
+ *	means support for per-station GTKs.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting.
+ *	This can be used to mask out antennas which are not attached or should
+ *	not be used for transmitting. If an antenna is not selected in this
+ *	bitmap the hardware is not allowed to transmit on this antenna.
+ *
+ *	Each bit represents one antenna, starting with antenna 1 at the first
+ *	bit. Depending on which antennas are selected in the bitmap, 802.11n
+ *	drivers can derive which chainmasks to use (if all antennas belonging to
+ *	a particular chain are disabled this chain should be disabled) and if
+ *	a chain has diversity antennas wether diversity should be used or not.
+ *	HT capabilities (STBC, TX Beamforming, Antenna selection) can be
+ *	derived from the available chains after applying the antenna mask.
+ *	Non-802.11n drivers can derive wether to use diversity or not.
+ *	Drivers may reject configurations or RX/TX mask combinations they cannot
+ *	support by returning -EINVAL.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving.
+ *	This can be used to mask out antennas which are not attached or should
+ *	not be used for receiving. If an antenna is not selected in this bitmap
+ *	the hardware should not be configured to receive on this antenna.
+ *	For a more detailed descripton see @NL80211_ATTR_WIPHY_ANTENNA_TX.
+ *
+ * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -951,6 +992,16 @@ enum nl80211_attrs {
 	NL80211_ATTR_RX_FRAME_TYPES,
 	NL80211_ATTR_FRAME_TYPE,
 
+	NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
+	NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
+
+	NL80211_ATTR_SUPPORT_IBSS_RSN,
+
+	NL80211_ATTR_WIPHY_ANTENNA_TX,
+	NL80211_ATTR_WIPHY_ANTENNA_RX,
+
+	NL80211_ATTR_MCAST_RATE,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -1006,6 +1057,8 @@ enum nl80211_attrs {
  * @NL80211_IFTYPE_WDS: wireless distribution interface
  * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
  * @NL80211_IFTYPE_MESH_POINT: mesh point
+ * @NL80211_IFTYPE_P2P_CLIENT: P2P client
+ * @NL80211_IFTYPE_P2P_GO: P2P group owner
  * @NL80211_IFTYPE_MAX: highest interface type number currently defined
  * @NUM_NL80211_IFTYPES: number of defined interface types
  *
@@ -1022,6 +1075,8 @@ enum nl80211_iftype {
 	NL80211_IFTYPE_WDS,
 	NL80211_IFTYPE_MONITOR,
 	NL80211_IFTYPE_MESH_POINT,
+	NL80211_IFTYPE_P2P_CLIENT,
+	NL80211_IFTYPE_P2P_GO,
 
 	/* keep last */
 	NUM_NL80211_IFTYPES,
@@ -1111,6 +1166,8 @@ enum nl80211_rate_info {
  * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station)
  * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this
  *	station)
+ * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station)
+ * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station)
  */
 enum nl80211_sta_info {
 	__NL80211_STA_INFO_INVALID,
@@ -1124,6 +1181,8 @@ enum nl80211_sta_info {
 	NL80211_STA_INFO_TX_BITRATE,
 	NL80211_STA_INFO_RX_PACKETS,
 	NL80211_STA_INFO_TX_PACKETS,
+	NL80211_STA_INFO_TX_RETRIES,
+	NL80211_STA_INFO_TX_FAILED,
 
 	/* keep last */
 	__NL80211_STA_INFO_AFTER_LAST,
@@ -1277,7 +1336,11 @@ enum nl80211_bitrate_attr {
  * 	wireless core it thinks its knows the regulatory domain we should be in.
  * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an
  * 	802.11 country information element with regulatory information it
- * 	thinks we should consider.
+ * 	thinks we should consider. cfg80211 only processes the country
+ *	code from the IE, and relies on the regulatory domain information
+ *	structure pased by userspace (CRDA) from our wireless-regdb.
+ *	If a channel is enabled but the country code indicates it should
+ *	be disabled we disable the channel and re-enable it upon disassociation.
  */
 enum nl80211_reg_initiator {
 	NL80211_REGDOM_SET_BY_CORE,
@@ -1382,6 +1445,17 @@ enum nl80211_reg_rule_flags {
  * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
  * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
  * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
+ * @NL80211_SURVEY_INFO_IN_USE: channel is currently being used
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME: amount of time (in ms) that the radio
+ *	spent on this channel
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY: amount of the time the primary
+ *	channel was sensed busy (either due to activity or energy detect)
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: amount of time the extension
+ *	channel was sensed busy
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_RX: amount of time the radio spent
+ *	receiving data
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_TX: amount of time the radio spent
+ *	transmitting data
  * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
  *	currently defined
  * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
@@ -1390,6 +1464,12 @@ enum nl80211_survey_info {
 	__NL80211_SURVEY_INFO_INVALID,
 	NL80211_SURVEY_INFO_FREQUENCY,
 	NL80211_SURVEY_INFO_NOISE,
+	NL80211_SURVEY_INFO_IN_USE,
+	NL80211_SURVEY_INFO_CHANNEL_TIME,
+	NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY,
+	NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY,
+	NL80211_SURVEY_INFO_CHANNEL_TIME_RX,
+	NL80211_SURVEY_INFO_CHANNEL_TIME_TX,
 
 	/* keep last */
 	__NL80211_SURVEY_INFO_AFTER_LAST,
@@ -1636,11 +1716,14 @@ enum nl80211_auth_type {
  * @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key
  * @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key
  * @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS)
+ * @NUM_NL80211_KEYTYPES: number of defined key types
  */
 enum nl80211_key_type {
 	NL80211_KEYTYPE_GROUP,
 	NL80211_KEYTYPE_PAIRWISE,
 	NL80211_KEYTYPE_PEERKEY,
+
+	NUM_NL80211_KEYTYPES
 };
 
 /**
@@ -1671,6 +1754,9 @@ enum nl80211_wpa_versions {
  *	CCMP keys, each six bytes in little endian
  * @NL80211_KEY_DEFAULT: flag indicating default key
  * @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key
+ * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not
+ *	specified the default depends on whether a MAC address was
+ *	given with the command using the key or not (u32)
  * @__NL80211_KEY_AFTER_LAST: internal
  * @NL80211_KEY_MAX: highest key attribute
  */
@@ -1682,6 +1768,7 @@ enum nl80211_key_attributes {
 	NL80211_KEY_SEQ,
 	NL80211_KEY_DEFAULT,
 	NL80211_KEY_DEFAULT_MGMT,
+	NL80211_KEY_TYPE,
 
 	/* keep last */
 	__NL80211_KEY_AFTER_LAST,