openwrt-owl/target/linux/ramips/dts/WHR-1166D.dts

/dts-v1/;

/include/ "mt7620a.dtsi"

/ {
	compatible = "ralink,mt7620a-soc";
	model = "Buffalo WHR-1166D";

	palmbus@10000000 {
		gpio2: gpio@660 {
			status = "okay";
		};

		spi@b00 {
			status = "okay";

			m25p80@0 {
				#address-cells = <1>;
				#size-cells = <1>;
				compatible = "en25q64";
				reg = <0 0>;
				linux,modalias = "m25p80", "mx25l6405d";
				spi-max-frequency = <10000000>;

				partition@0 {
					label = "u-boot";
					reg = <0x0 0x30000>;
					read-only;
				};

				partition@30000 {
					label = "u-boot-env";
					reg = <0x30000 0x10000>;
					read-only;
				};

				factory: partition@40000 {
					label = "factory";
					reg = <0x40000 0x10000>;
					read-only;
				};

				partition@50000 {
					label = "firmware";
					reg = <0x50000 0xeb0000>;
				};

				partition@e00000 {
					label = "usercfg";
					reg = <0xf00000 0x100000>;
				};
			};
		};
	};

	pinctrl {
		state_default: pinctrl0 {
			gpio {
				ralink,group = "i2c", "uartf", "rgmii1", "wled", "nd_sd";
				ralink,function = "gpio";
			};
		};
	};

	ethernet@10100000 {
		pinctrl-names = "default";
		pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;

		port@5 {
			status = "okay";
			phy-handle = <&phy5>;
			phy-mode = "rgmii";
		};

		mdio-bus {
			status = "okay";

			phy5: ethernet-phy@5 {
				reg = <5>;
				phy-mode = "rgmii";
			};
		};
	};

	gsw@10110000 {
		ralink,port4 = "ephy";
	};

	wmac@10180000 {
		ralink,mtd-eeprom = <&factory 0>;
	};

	pcie@10140000 {
		status = "okay";

		pcie-bridge {
			mt76@0,0 {
				reg = <0x0000 0 0 0 0>;
				device_type = "pci";
				ralink,mtd-eeprom = <&factory 32768>;
			};
		};
	};
	
	gpio-leds {
		compatible = "gpio-leds";
		power {
			label = "buffalo:red:power";
			gpios = <&gpio0 7 1>;
		};
		status {
			label = "buffalo:green:status";
			gpios = <&gpio0 8 1>;
		};
		power2 {
			label = "buffalo:green:power";
			gpios = <&gpio0 9 1>;
		};
		status2 {
			label = "buffalo:orange:status";
			gpios = <&gpio0 10 1>;
		};
		internet {
			label = "buffalo:green:internet";
			gpios = <&gpio2 17 1>;
		};
		router {
			label = "buffalo:green:router";
			gpios = <&gpio2 18 1>;
		};
		router2 {
			label = "buffalo:orange:router";
			gpios = <&gpio2 19 1>;
		};
	};

	gpio-keys-polled {
		compatible = "gpio-keys-polled";
		#address-cells = <1>;
		#size-cells = <0>;
		poll-interval = <20>;
		s1 {
			label = "reset";
			gpios = <&gpio2 12 1>;
			linux,code = <0x100>;
		};
		s2 {
			label = "aoss";
			gpios = <&gpio2 13 1>;
			linux,code = <0x101>;
		};
		s3 {
			label = "ap";
			gpios = <&gpio2 14 1>;
			linux,code = <0x102>;
		};
		s4 {
			label = "bridge";
			gpios = <&gpio2 15 1>;
			linux,code = <0x103>;
		};
	};
};