openwrt-owl/target/linux/ixp4xx/patches-2.6.28/191-cambria_optional_uart.patch

--- a/arch/arm/mach-ixp4xx/cambria-setup.c
+++ b/arch/arm/mach-ixp4xx/cambria-setup.c
@@ -34,6 +34,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/setup.h>
+#include <linux/irq.h>
 
 struct cambria_board_info {
 	unsigned char	*model;
@@ -127,6 +128,45 @@ static struct platform_device cambria_ua
 	.resource	= &cambria_uart_resource,
 };
 
+static struct resource cambria_optional_uart_resources[] = {
+	{
+		.start	= 0x52000000,
+		.end	= 0x52000fff,
+		.flags	= IORESOURCE_MEM
+	},
+	{
+		.start	= 0x53000000,
+		.end	= 0x53000fff,
+		.flags	= IORESOURCE_MEM
+	}
+};
+
+static struct plat_serial8250_port cambria_optional_uart_data[] = {
+	{
+		.flags		= UPF_BOOT_AUTOCONF,
+		.iotype		= UPIO_MEM_DELAY,
+		.regshift	= 0,
+		.uartclk	= 1843200,
+		.rw_delay	= 2,
+	},
+	{
+		.flags		= UPF_BOOT_AUTOCONF,
+		.iotype		= UPIO_MEM_DELAY,
+		.regshift	= 0,
+		.uartclk	= 1843200,
+		.rw_delay	= 2,
+	},
+  { },
+};
+
+static struct platform_device cambria_optional_uart = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM1,
+	.dev.platform_data	= cambria_optional_uart_data,
+	.num_resources	= 2,
+	.resource	= cambria_optional_uart_resources,
+};
+
 static struct resource cambria_pata_resources[] = {
 	{
 		.flags	= IORESOURCE_MEM
@@ -283,6 +323,19 @@ static void __init cambria_gw23xx_setup(
 
 static void __init cambria_gw2350_setup(void)
 {
+	*IXP4XX_EXP_CS2 = 0xBFFF3C43;
+	set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING);
+	cambria_optional_uart_data[0].mapbase	= 0x52FF0000;
+	cambria_optional_uart_data[0].membase	= (void __iomem *)ioremap(0x52FF0000, 0x0fff);
+	cambria_optional_uart_data[0].irq		= IRQ_IXP4XX_GPIO3;
+
+	*IXP4XX_EXP_CS3 = 0xBFFF3C43;
+	set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING);
+	cambria_optional_uart_data[1].mapbase	= 0x53FF0000;
+	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53FF0000, 0x0fff);
+	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
+
+	platform_device_register(&cambria_optional_uart);
 	platform_device_register(&cambria_npec_device);
 	platform_device_register(&cambria_npea_device);
 
@@ -294,6 +347,19 @@ static void __init cambria_gw2350_setup(
 
 static void __init cambria_gw2358_setup(void)
 {
+	*IXP4XX_EXP_CS3 = 0xBFFF3C43;
+	set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING);
+	cambria_optional_uart_data[0].mapbase	= 0x53FC0000;
+	cambria_optional_uart_data[0].membase	= (void __iomem *)ioremap(0x53FC0000, 0x0fff);
+	cambria_optional_uart_data[0].irq		= IRQ_IXP4XX_GPIO3;
+
+	set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING);
+	cambria_optional_uart_data[1].mapbase	= 0x53F80000;
+	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53F80000, 0x0fff);
+	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
+
+	platform_device_register(&cambria_optional_uart);
+
 	platform_device_register(&cambria_npec_device);
 	platform_device_register(&cambria_npea_device);
 
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -26,6 +26,7 @@ struct plat_serial8250_port {
 	void            *private_data;
 	unsigned char	regshift;	/* register shift */
 	unsigned char	iotype;		/* UPIO_* */
+	unsigned int rw_delay;	/* udelay for slower busses IXP4XX Expansion Bus */
 	unsigned char	hub6;
 	upf_t		flags;		/* UPF_* flags */
 };
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -262,6 +262,7 @@ struct uart_port {
 #define UPIO_TSI		(5)			/* Tsi108/109 type IO */
 #define UPIO_DWAPB		(6)			/* DesignWare APB UART */
 #define UPIO_RM9000		(7)			/* RM9000 type IO */
+#define UPIO_MEM_DELAY	(8)
 
 	unsigned int		read_status_mask;	/* driver specific */
 	unsigned int		ignore_status_mask;	/* driver specific */
@@ -301,6 +302,7 @@ struct uart_port {
 
 	unsigned int		mctrl;			/* current modem ctrl settings */
 	unsigned int		timeout;		/* character-based timeout */
+	unsigned int		rw_delay;		/* udelay for slow busses, IXP4XX Expansion Bus */
 	unsigned int		type;			/* port type */
 	const struct uart_ops	*ops;
 	unsigned int		custom_divisor;
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -373,6 +373,8 @@ static unsigned int serial_in(struct uar
 		outb(up->port.hub6 - 1 + offset, up->port.iobase);
 		return inb(up->port.iobase + 1);
 
+	case UPIO_MEM_DELAY:
+		udelay(up->port.rw_delay);
 	case UPIO_MEM:
 	case UPIO_DWAPB:
 		return readb(up->port.membase + offset);
@@ -411,6 +413,8 @@ serial_out(struct uart_8250_port *up, in
 		outb(value, up->port.iobase + 1);
 		break;
 
+	case UPIO_MEM_DELAY:
+		udelay(up->port.rw_delay);
 	case UPIO_MEM:
 		writeb(value, up->port.membase + offset);
 		break;
@@ -2823,6 +2827,7 @@ static int __devinit serial8250_probe(st
 		port.hub6		= p->hub6;
 		port.private_data	= p->private_data;
 		port.dev		= &dev->dev;
+		port.rw_delay	= p->rw_delay;
 		if (share_irqs)
 			port.flags |= UPF_SHARE_IRQ;
 		ret = serial8250_register_port(&port);
@@ -2972,6 +2977,7 @@ int serial8250_register_port(struct uart
 		uart->port.iotype       = port->iotype;
 		uart->port.flags        = port->flags | UPF_BOOT_AUTOCONF;
 		uart->port.mapbase      = port->mapbase;
+		uart->port.rw_delay			= port->rw_delay;
 		uart->port.private_data = port->private_data;
 		if (port->dev)
 			uart->port.dev = port->dev;
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -2161,6 +2161,7 @@ uart_report_port(struct uart_driver *drv
 		snprintf(address, sizeof(address),
 			 "I/O 0x%lx offset 0x%x", port->iobase, port->hub6);
 		break;
+	case UPIO_MEM_DELAY:
 	case UPIO_MEM:
 	case UPIO_MEM32:
 	case UPIO_AU:
@@ -2577,6 +2578,7 @@ int uart_match_port(struct uart_port *po
 	case UPIO_HUB6:
 		return (port1->iobase == port2->iobase) &&
 		       (port1->hub6   == port2->hub6);
+	case UPIO_MEM_DELAY:
 	case UPIO_MEM:
 	case UPIO_MEM32:
 	case UPIO_AU: