openwrt-owl/target/linux/pxa/patches-2.6.21/044-smc911x-fixup.patch

--- a/drivers/net/smc911x.c
+++ b/drivers/net/smc911x.c
@@ -76,6 +76,7 @@ static const char version[] =
 #include <linux/etherdevice.h>
 #include <linux/skbuff.h>
 
+#include <linux/irq.h>
 #include <asm/io.h>
 #include <asm/irq.h>
 
@@ -303,14 +304,14 @@ static void smc911x_reset(struct net_dev
 	SMC_SET_AFC_CFG(lp->afc_cfg);
 
 
-	/* Set to LED outputs */
-	SMC_SET_GPIO_CFG(0x70070000);
+	/* Set to LED outputs and configure EEPROM pins as GP outputs */
+	SMC_SET_GPIO_CFG(GPIO_CFG_LED1_EN_ | GPIO_CFG_LED2_EN_ | 1 << 20);
 
 	/*
-	 * Deassert IRQ for 1*10us for edge type interrupts
+	 * Deassert IRQ for 22*10us for edge type interrupts
 	 * and drive IRQ pin push-pull
 	 */
-	SMC_SET_IRQ_CFG( (1 << 24) | INT_CFG_IRQ_EN_ | INT_CFG_IRQ_TYPE_ );
+	SMC_SET_IRQ_CFG( (22 << 24) | INT_CFG_IRQ_EN_ | INT_CFG_IRQ_TYPE_ );
 
 	/* clear anything saved */
 	if (lp->pending_tx_skb != NULL) {
@@ -413,7 +414,7 @@ static inline void smc911x_drop_pkt(stru
 	if (fifo_count <= 4) {
 		/* Manually dump the packet data */
 		while (fifo_count--)
-			SMC_GET_RX_FIFO();
+			(void)SMC_GET_RX_FIFO();
 	} else	 {
 		/* Fast forward through the bad packet */
 		SMC_SET_RX_DP_CTRL(RX_DP_CTRL_FFWD_BUSY_);
@@ -900,6 +901,7 @@ static void smc911x_phy_powerdown(struct
 	unsigned long ioaddr = dev->base_addr;
 	unsigned int bmcr;
 
+	DBG(SMC_DEBUG_FUNC, "%s: --> %s\n", dev->name, __FUNCTION__);
 	/* Enter Link Disable state */
 	SMC_GET_PHY_BMCR(phy, bmcr);
 	bmcr |= BMCR_PDOWN;
@@ -925,6 +927,7 @@ static void smc911x_phy_check_media(stru
 
 	if (mii_check_media(&lp->mii, netif_msg_link(lp), init)) {
 		/* duplex state has changed */
+		DBG(SMC_DEBUG_MISC, "%s: duplex state has changed\n", dev->name);
 		SMC_GET_PHY_BMCR(phyaddr, bmcr);
 		SMC_GET_MAC_CR(cr);
 		if (lp->mii.full_duplex) {
@@ -960,6 +963,7 @@ static void smc911x_phy_configure(struct
 	int my_phy_caps; /* My PHY capabilities */
 	int my_ad_caps; /* My Advertised capabilities */
 	int status;
+	int bmcr;
 	unsigned long flags;
 
 	DBG(SMC_DEBUG_FUNC, "%s: --> %s()\n", dev->name, __FUNCTION__);
@@ -1033,9 +1037,12 @@ static void smc911x_phy_configure(struct
 
 	DBG(SMC_DEBUG_MISC, "%s: phy caps=0x%04x\n", dev->name, my_phy_caps);
 	DBG(SMC_DEBUG_MISC, "%s: phy advertised caps=0x%04x\n", dev->name, my_ad_caps);
+	DBG(SMC_DEBUG_MISC, "%s: phy advertised readback caps=0x%04x\n", dev->name, status);
 
 	/* Restart auto-negotiation process in order to advertise my caps */
-	SMC_SET_PHY_BMCR(phyaddr, BMCR_ANENABLE | BMCR_ANRESTART);
+	SMC_GET_PHY_BMCR(phyaddr, bmcr);
+	bmcr |= BMCR_ANENABLE | BMCR_ANRESTART;
+	SMC_SET_PHY_BMCR(phyaddr, bmcr);
 
 	smc911x_phy_check_media(dev, 1);
 
@@ -1888,6 +1895,39 @@ static int __init smc911x_findirq(unsign
 	return probe_irq_off(cookie);
 }
 
+static inline unsigned int is_gumstix_oui(u8 *addr)
+{
+	return (addr[0] == 0x00 && addr[1] == 0x15 && addr[2] == 0xC9);
+}
+
+/**
+ * gen_serial_ether_addr - Generate software assigned Ethernet address
+ * based on the system_serial number
+ * @addr: Pointer to a six-byte array containing the Ethernet address
+ *
+ * Generate an Ethernet address (MAC) that is not multicast
+ * and has the local assigned bit set, keyed on the system_serial
+ */
+static inline void gen_serial_ether_addr(u8 *addr)
+{
+	static u8 ether_serial_digit = 0;
+	addr [0] = system_serial_high >> 8;
+	addr [1] = system_serial_high;
+	addr [2] = system_serial_low >> 24;
+	addr [3] = system_serial_low >> 16;
+	addr [4] = system_serial_low >> 8;
+	addr [5] = (system_serial_low & 0xc0) |	/* top bits are from system serial */
+		(1 << 4) |			/* 2 bits identify interface type 1=ether, 2=usb, 3&4 undef */
+		((ether_serial_digit++) & 0x0f);	/* 15 possible interfaces of each type */
+
+	if(!is_gumstix_oui(addr))
+	{
+		addr [0] &= 0xfe;		/* clear multicast bit */
+		addr [0] |= 0x02;		/* set local assignment bit (IEEE802) */
+	}
+}
+
+
 /*
  * Function: smc911x_probe(unsigned long ioaddr)
  *
@@ -2116,15 +2156,13 @@ static int __init smc911x_probe(struct n
 #endif
 		printk("\n");
 		if (!is_valid_ether_addr(dev->dev_addr)) {
-			printk("%s: Invalid ethernet MAC address. Please "
-					"set using ifconfig\n", dev->name);
-		} else {
-			/* Print the Ethernet address */
-			printk("%s: Ethernet addr: ", dev->name);
-			for (i = 0; i < 5; i++)
-				printk("%2.2x:", dev->dev_addr[i]);
-			printk("%2.2x\n", dev->dev_addr[5]);
+			gen_serial_ether_addr(dev->dev_addr);
 		}
+		/* Print the Ethernet address */
+		printk("%s: Ethernet addr: ", dev->name);
+		for (i = 0; i < 5; i++)
+			printk("%2.2x:", dev->dev_addr[i]);
+		printk("%2.2x\n", dev->dev_addr[5]);
 
 		if (lp->phy_type == 0) {
 			PRINTK("%s: No PHY found\n", dev->name);
@@ -2300,8 +2338,15 @@ static struct platform_driver smc911x_dr
 	},
 };
 
+#ifdef CONFIG_ARCH_GUMSTIX
+extern void gumstix_smc911x_load(void);
+#endif
+
 static int __init smc911x_init(void)
 {
+#ifdef CONFIG_ARCH_GUMSTIX
+	gumstix_smc911x_load();
+#endif
 	return platform_driver_register(&smc911x_driver);
 }
 
--- /dev/null
+++ b/drivers/net/gumstix-smc911x.c
@@ -0,0 +1,148 @@
+/*
+ *  Gumstix SMC911x chip intialization driver
+ *
+ *  Author:     Craig Hughes
+ *  Created:    December 9, 2004
+ *  Copyright:  (C) 2004 Craig Hughes
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+
+#include <asm/hardware.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/delay.h>
+
+#include <asm/arch/gumstix.h>
+
+#define SMC_DEBUG               9
+#include <asm/io.h>
+#include "smc911x.h"
+
+static struct resource gumstix_smc911x0_resources[] = {
+	[0] = {
+		.name	= "smc911x-regs",
+		.start  = PXA_CS1_PHYS,
+		.end    = PXA_CS1_PHYS + 0x000fffff,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = GUMSTIX_ETH0_IRQ,
+		.end    = GUMSTIX_ETH0_IRQ,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct resource gumstix_smc911x1_resources[] = {
+	[0] = {
+		.name	= "smc911x-regs",
+		.start	= PXA_CS2_PHYS,
+		.end	= PXA_CS2_PHYS + 0x000fffff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= GUMSTIX_ETH1_IRQ,
+		.end	= GUMSTIX_ETH1_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device gumstix_smc911x0_device = {
+	.name           = "smc911x",
+	.id             = 0,
+	.num_resources  = ARRAY_SIZE(gumstix_smc911x0_resources),
+	.resource       = gumstix_smc911x0_resources,
+};
+
+static struct platform_device gumstix_smc911x1_device = {
+	.name           = "smc911x",
+	.id             = 1,
+	.num_resources  = ARRAY_SIZE(gumstix_smc911x1_resources),
+	.resource       = gumstix_smc911x1_resources,
+};
+
+static struct platform_device *smc911x_devices[] = {
+	&gumstix_smc911x0_device,
+	&gumstix_smc911x1_device,
+};
+
+/* First we're going to test if there's a 2nd SMC911x, and if not, then we'll free up those resources and the GPIO lines
+ * that it would otherwise use.  We have no choice but to probe by doing:
+ * Set nCS2 to CS2 mode
+ * Set the reset line to GPIO out mode, and pull it high, then drop it low (to trigger reset)
+ * Read from the memory space to check for the sentinel sequence identifying a likely SMC911x device
+ */
+int __init gumstix_smc911x_init(void)
+{
+	unsigned int val, num_devices=ARRAY_SIZE(smc911x_devices);
+	void *ioaddr;
+
+	/* Set up nPWE */
+	pxa_gpio_mode(GPIO49_nPWE_MD);
+
+	pxa_gpio_mode(GPIO78_nCS_2_MD);
+	// If either if statement fails, then we'll drop out and turn_off_eth1,
+	// if both succeed, then we'll skip that and just proceed with 2 cards
+	if(request_mem_region(gumstix_smc911x1_resources[1].start, SMC911X_IO_EXTENT, "smc911x probe"))
+	{
+		ioaddr = ioremap(gumstix_smc911x1_resources[1].start, SMC911X_IO_EXTENT);
+		val = SMC_GET_PN();
+		iounmap(ioaddr);
+		release_mem_region(gumstix_smc911x1_resources[1].start, SMC911X_IO_EXTENT);
+		if (CHIP_9115 == val ||
+			CHIP_9116 == val ||
+			CHIP_9117 == val ||
+			CHIP_9118 == val ) {
+			goto proceed;
+		}
+	}
+
+turn_off_eth1:
+	// This is apparently not an SMC911x
+	// So, let's decrement the number of devices to request, and reset the GPIO lines to GPIO IN mode
+	num_devices--;
+	smc911x_devices[1] = NULL;
+	pxa_gpio_mode(78 | GPIO_IN);
+	
+proceed:
+	pxa_gpio_mode(GPIO15_nCS_1_MD);
+
+	if(smc911x_devices[1]) pxa_gpio_mode(GPIO_GUMSTIX_ETH1_RST_MD);
+	pxa_gpio_mode(GPIO_GUMSTIX_ETH0_RST_MD);
+
+	if(smc911x_devices[1]) GPCR(GPIO_GUMSTIX_ETH1_RST) = GPIO_bit(GPIO_GUMSTIX_ETH1_RST);
+	GPCR(GPIO_GUMSTIX_ETH0_RST) = GPIO_bit(GPIO_GUMSTIX_ETH0_RST);
+	msleep(500); // Hold RESET for at least 200µ
+
+	if(smc911x_devices[1]) GPSR(GPIO_GUMSTIX_ETH1_RST) = GPIO_bit(GPIO_GUMSTIX_ETH1_RST);
+	GPSR(GPIO_GUMSTIX_ETH0_RST) = GPIO_bit(GPIO_GUMSTIX_ETH0_RST);
+	msleep(50);
+
+	return platform_add_devices(smc911x_devices, num_devices);
+}
+
+void __exit gumstix_smc911x_exit(void)
+{
+	if(smc911x_devices[1] != NULL) platform_device_unregister(&gumstix_smc911x1_device);
+	platform_device_unregister(&gumstix_smc911x0_device);
+}
+
+void gumstix_smc911x_load(void) {}
+EXPORT_SYMBOL(gumstix_smc911x_load);
+
+module_init(gumstix_smc911x_init);
+module_exit(gumstix_smc911x_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Craig Hughes <craig@gumstix.com>");
+MODULE_DESCRIPTION("Gumstix board SMC911x chip initialization driver");
+MODULE_VERSION("1:0.1");
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1020,6 +1020,13 @@ config SMC911X
 	  called smc911x.  If you want to compile it as a module, say M 
 	  here and read <file:Documentation/modules.txt>
 
+config SMC911X_GUMSTIX
+	tristate
+	default m if SMC911X=m
+	default y if SMC911X=y
+	depends on SMC911X && ARCH_GUMSTIX
+
+
 config NET_VENDOR_RACAL
 	bool "Racal-Interlan (Micom) NI cards"
 	depends on NET_ETHERNET && ISA
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -202,6 +202,7 @@ obj-$(CONFIG_PASEMI_MAC) += pasemi_mac.o
 obj-$(CONFIG_MACB) += macb.o
 
 obj-$(CONFIG_SMC91X_GUMSTIX) += gumstix-smc91x.o
+obj-$(CONFIG_SMC911X_GUMSTIX) += gumstix-smc911x.o
 obj-$(CONFIG_ARM) += arm/
 obj-$(CONFIG_DEV_APPLETALK) += appletalk/
 obj-$(CONFIG_TR) += tokenring/
--- a/include/asm-arm/arch-pxa/gumstix.h
+++ b/include/asm-arm/arch-pxa/gumstix.h
@@ -52,7 +52,7 @@
 #define GPIO_GUMSTIX_ETH0_RST		80
 #define GPIO_GUMSTIX_ETH0		36
 #else
-#define GPIO_GUMSTIX_ETH0_RST		32
+#define GPIO_GUMSTIX_ETH0_RST		107
 #define GPIO_GUMSTIX_ETH0		99
 #endif
 #define GPIO_GUMSTIX_ETH1_RST		52
--- a/drivers/net/smc911x.h
+++ b/drivers/net/smc911x.h
@@ -33,7 +33,9 @@
  * Use the DMA feature on PXA chips
  */
 #ifdef CONFIG_ARCH_PXA
+#if !defined( CONFIG_SMC911X_GUMSTIX ) && !defined( CONFIG_SMC911X_GUMSTIX_MODULE )
   #define SMC_USE_PXA_DMA	1
+#endif
   #define SMC_USE_16BIT		0
   #define SMC_USE_32BIT		1
 #endif
@@ -46,13 +48,13 @@
 #if	SMC_USE_16BIT
 #define SMC_inb(a, r)			 readb((a) + (r))
 #define SMC_inw(a, r)			 readw((a) + (r))
-#define SMC_inl(a, r)			 ((SMC_inw(a, r) & 0xFFFF)+(SMC_inw(a+2, r)<<16))
+#define SMC_inl(a, r)			 ((SMC_inw(a, r) & 0xFFFF)+(SMC_inw((a)+2, r)<<16))
 #define SMC_outb(v, a, r)		 writeb(v, (a) + (r))
 #define SMC_outw(v, a, r)		 writew(v, (a) + (r))
 #define SMC_outl(v, a, r) 			 \
 	do{					 \
-		 writel(v & 0xFFFF, (a) + (r));	 \
-		 writel(v >> 16, (a) + (r) + 2); \
+		 writel((v) & 0xFFFF, (a) + (r));	 \
+		 writel((v) >> 16, (a) + (r) + 2); \
 	 } while (0)
 #define SMC_insl(a, r, p, l)	 readsw((short*)((a) + (r)), p, l*2)
 #define SMC_outsl(a, r, p, l)	 writesw((short*)((a) + (r)), p, l*2)